When installing bearing on shaft, hit/contact the bearing inner ring. Not the outer ring or it will damage the bearing, specially when it's a tight tolerance fit.
Для тех кому интересно - это планетарноцевочный редуктор… очень эффективная штука при понижении числа оборотов до больших значений в малом корпусе. Минус в сложности изготовлении и частых заклиниваниях…
If the press fit is on the inner, you tap on the inner, if on the outer, tap on the outer otherwise the balls leave dimples on the running surface and you start with a stuffed bearing.
That is 100% wrong. First, the guy above me explained it well, and second these are hardened and wont take any damage from light tapping. The worst that could happen is that if you tap too hard the ring could shatter in thousands of pieces - but definetly not with the tapping shown in the vid
sim, foi muito errado ele bater com um martelo de metal isso vai arranhar e danificar a peça, tem que bater com um martelo de madeira revertido de couro ou emborrachado, martelo de borracha nunca vai arranhar as peças.
Small taps may not he too bad. It's all a case of knowing metal and hardness and what impact will deform. You CAN use a chisel as a screwdriver and visa versa; depends on circumstances!!! PS. I own over a 100 ! .... and respect the difference!
I don't think the few soft taps he gave the bearings would hurt them, though he could have greased the bearings before inserting them. Sure they will get grease eventually, but there can be some significant wear if they run dry under load for any period of time. The majority of wear to your engine bearings occurs in the first 30 seconds of starting your car in the morning.
It’s sad that fewer and fewer people get experience how satisfying this is…rebuilding a transmission, steering gear, etc. with cleaned parts and new gaskets and seals.
I've rebuilt several of these units part of a centrifuge/strainer equipment. They have a grease line on the bottom. When the grease line brakes they don't last very long.
Not an excellent job! Looks like a job of a novice. should have packed both bearings with grease before mounting them. Pounding metal to metal is another no no!
@@roaringcat1 Come on man, you use a bushing that is the same diameter as the inner race of the bearing, to lightly tap against. Never ever hit the outer race unless you like redoing your work in the not too distant future.
Если нужно забить подшипник, то используй трубку того же диаметра, что и внутреннее кольцо подшипника. Технология провкренная временем. Трубка гораздо более мягкая, чем подшипник
Сколько помню, в СССР все молотком собирали, даже телевизор после удара по нему работать начинал😂 а теперь все увидев стук по подшипнику, умничают. Умелые руки, и молотком все аккуратно сделают, а рукопоп, и прессом перекосит обойму.
NLG 1 grease or 00 imo ,not very common to see since most parts use the type 2 but I see the mechanism there might require a constant lubrication flow grease tho
Everything was fine until he hammered on the outer race. Contrary to popular belief, you can use a hammer to seat a bearing. However, you must ONLY hammer on the race making contact. If you are seating it into a flange, you hammer the outer race; on a shaft, hammer the inner race. It’s intuitive once you understand.
It's a sumitomo cyclo gear box not a auto transmission. It achieves incredibly low gear ratios the part he is striking in isn't damaged I've assembled hundreds of these.
Idk but I'm not a mechanic, but there's something I just love about mechanics, maybe it's just fitting joints perfectly and lubricating; and seeing it works perfectly, and complex fun trying again if not
Never hit machine parts with a steel hammer.
It is made in China😂
Never heard that before. Noted friend.
@@jtjjbannie plastic, leather brass all work and won't damage or distort a part
А если машина не заводится?
Yeah his wood hammer used 😊😊
Вся красота видео оборвалась с ударами молотка по наружной обойме подшипника
И прокладку еще криво подожил
😅😮😮@@hihirururara 😅😅😮😂😂
😂😢
😂😂😂 é verdade!
Что ещё ожидать от кетайской сборки
When installing bearing on shaft, hit/contact the bearing inner ring. Not the outer ring or it will damage the bearing, specially when it's a tight tolerance fit.
Yes sir. Absolutely.
Nie ucz ojca dzieci robić 🤣🤣 on to lubi robić więc wali w łożysko żeby niedługo rozebrać ponownie 👍
I think that cylindrical tool is cut out to avoid this, but not sure.
It's made in china 😂
Для тех кому интересно - это планетарноцевочный редуктор… очень эффективная штука при понижении числа оборотов до больших значений в малом корпусе. Минус в сложности изготовлении и частых заклиниваниях…
Thanks I was wondering 😊
Если не запомнить последовательность , то его очень долго собирать.
А где он применяется, Вадим? Скажи пожалуйста.
@@Stanislavskiy1985 в самокатах.Мотор-колесо кароче.
@@Demonius1976 🤝👍
Son: Mom what's there special tonight to eat?
Mom: crank shaft with lubricant oil hammered with barring wheel.
Underrated comment
Jajajaj 😂😂
Not funny
😂😂😂😂
Bearing*
- How much grease should I use?
- Yes.
He didn't even use enough
it seemed to be just the right amount...
Хаха
More, he skimped like a skimper. Should’ve covered the last cog. I forgot what the parts to a harmonic drive are. Wonder what this one is for
How much you got?
Так хорошо все начиналось! Но осаживания подшипника убил😂
С языка снял
+
Ты чо не слышишь китайскую музыку? Вместо тысячи слов😅
Китайская сборка😂😂😂😂
Там ещё шплинт не поставил
Подшипник, молотком?!?! Удачи!!!!
В Китае похоже это норма, в прочем и в России тоже.
Bro made all of Russia angry with this post.
А что с ним будет то? Особенно если по внутренней обойме не сильно бить...
Not with a metal hammer beating on a bearing , no wonder my transmission had to be overhaul this past summer !
а шпильки где?зафиксировано?га
Thought the same.
And never hit the out race to seat a bearing!
No wonder
Didn't pack the bearing either.
Wow, changing the blinker fluid is way more complicated than I thought! 😂
That’s because it’s for a BMW. That’s why drivers don’t want to wear them out by using them.
Haha
I guess he lost his rubber hammer... never tap in a bearing with a steel hammer.
Yeah i know, instant claim😂😂😂 warranty better be good on this. Its going to have scarring
Still no excuse... Use the wood tip of your hammer handle...
Dead Blow Hammer.
Guess what! It works and last just as long too
Not usa clearly
I feel like im getting a tableside presentation at a mechanics restaurant
I could go for a slice of lemon meringue pie right about now.
Shit, you ain't kidding, was just thinking about one yesterday.
Thats the levelof that lubricant. Just one use
I’m actually eating some lemon meringue pie while watching this!
My wife is going to make two Key Lime pies tomorrow. Stop by.
Ye ye
Never tap on the center race of a bearing. You'll cause flat places on it and the it will wear out faster.
If the press fit is on the inner, you tap on the inner, if on the outer, tap on the outer otherwise the balls leave dimples on the running surface and you start with a stuffed bearing.
That is 100% wrong. First, the guy above me explained it well, and second these are hardened and wont take any damage from light tapping. The worst that could happen is that if you tap too hard the ring could shatter in thousands of pieces - but definetly not with the tapping shown in the vid
sim, foi muito errado ele bater com um martelo de metal isso vai arranhar e danificar a peça, tem que bater com um martelo de madeira revertido de couro ou emborrachado, martelo de borracha nunca vai arranhar as peças.
You dont know what the hell you're talking about.
@@noreply5829The balls are harder than the race. They leave indents. Try it yourself.
Small taps may not he too bad. It's all a case of knowing metal and hardness and what impact will deform. You CAN use a chisel as a screwdriver and visa versa; depends on circumstances!!!
PS. I own over a 100 ! .... and respect the difference!
Hey, it's the internet - everything is absolute!
Молотком по подшипнику без проставки, ну очень технологично))))
Steel hammer and bearings usually don't mix unless destroying them..a rubber mallet would work a touch better I would guess..
Leather mallet
Use a block of Wood
and never hit the outer ring!
I don't think the few soft taps he gave the bearings would hurt them, though he could have greased the bearings before inserting them.
Sure they will get grease eventually, but there can be some significant wear if they run dry under load for any period of time.
The majority of wear to your engine bearings occurs in the first 30 seconds of starting your car in the morning.
Did I miss you putting in the key in the"keyway"?
I thought that too. It doesn’t look like he put one in and I can’t see an edit where it was done.
Yes
I thought the same thing but the first split second of the video, you can see the key on the shaft.
@@benlindsey8082 😅 good call!
I saw the same thing.....that first bearing had a key slot.....
It’s sad that fewer and fewer people get experience how satisfying this is…rebuilding a transmission, steering gear, etc. with cleaned parts and new gaskets and seals.
that middle bearing is the nicest bearing ive ever seen
Германские и японские автоинженеров нервно сидят в стороне и курят...
Not really, they should have used another type of hammer on the product piece. It will get damaged.
Dead Blow Hammer.
And Russia is completely going down the drain...
@@user-dv7hq2rh4g youd be surprised friend. Groceries are cheaper here than in Canada, Germany, France, Norway, etc.
You destroyed last bearing
Sealed bearing Sir....
Nah...
If he did it's the worst bearing imaginable. Barely tapped on it.
I totally agree. It was going so well. Did he even hit it straight!😅
How come that last bearing went in dry no Greece?
Когда хвостовик напильника лучший инструмент))
I bet he never hits a bearing with a steel hammer again
nahh, it's actually fine, especially the way he did it. No bearing got hurt during the making of this video.
Стальным молотком по обойме подшипника?
В гейропе или СШП обычная практика
@@MT3-82 И потом ещё добил через проставку по наружней обойме! За такое вообще по рукам надо надавать....
Looked like you forgot to put the key in. Light hammer taps don’t looked that bad.
Dude listening to that 1030ad music. Dope.
эстетическое удовольствие...до последнего подшипника (((
I í9
I've rebuilt several of these units part of a centrifuge/strainer equipment. They have a grease line on the bottom. When the grease line brakes they don't last very long.
It's a cycloidal gear and the grease is likely to be something called "Mollywhite 00 grease" or "FZ Multemp 00"
If that helps at all
so its a drive coupling? i stared at it for a while wondering what it was.
Какая душевная музыка на заднем фоне, прям так и веет качеством деталей оттуда 😂
The music is so good. Beautiful
Chinese
Glad this person isn't rebuilding my stuff.
That lubricant looks delicious!
soft lemon curd.
Makan lah
When a chef becomes automobile engineer 😅
That's why you don't buy foreign parts, hitting bearings with hammer, not lubricating the bearings
Good job but you need more grease.
He needed to grease the inner bearings before dropping them in.
Not an excellent job! Looks like a job of a novice. should have packed both bearings with grease before mounting them. Pounding metal to metal is another no no!
Орбитальный редуктор, просто шедевр. Подшипник так себе по качеству, если приходится молотком запрессовать а не кувалдой.
Мужики видят детали техники со смазкой,
Женщины видят груду металла в жиже,
Дети видят слайм!
Rule #12345 if bearing dont go get a bigger hammer.
Эй "мастер"... а шпонку кто ставить будет?!
O9
Есть там шпонка. Присмотрись. Я тоже думал что нет.
Нормально, последний подшипник заколотил☝🏻🤣🤣
Oh wait, I forgot to put the key in.😮
That's what I thought
Этого рабочего нужно сразу увольнять.
لماذا ؟
ممكن تشرح لي
Now just wait 12 hours for the epoxy to set
That ungreased part at the top hurts me the most.....😩😣
Needs more grease.....
After seeing parts tapped together with a ball peen hammer I wouldn't let this person restore my lawnmower.
What do you think he should've used to put the bearing on with a feather?
@@roaringcat1 Come on man, you use a bushing that is the same diameter as the inner race of the bearing, to lightly tap against. Never ever hit the outer race unless you like redoing your work in the not too distant future.
@@brianlangum6253 I have tapped them in with a hammer for over 40 years and never had a problem
только приходиться потом за китайцев потом подшипники смазкой самому набивать, куда пропадает пока едет к нам )
Если нужно забить подшипник, то используй трубку того же диаметра, что и внутреннее кольцо подшипника. Технология провкренная временем. Трубка гораздо более мягкая, чем подшипник
А шпонка подшипника! Как так?
Это под эксцентрик… в подшипнике нет паза. планитарноцевочный редуктор загуглите…
Well you that bearing is going to spin on it's shaft. Right for a sec then super loose. Overseas quality right there...
Сколько помню, в СССР все молотком собирали, даже телевизор после удара по нему работать начинал😂 а теперь все увидев стук по подшипнику, умничают. Умелые руки, и молотком все аккуратно сделают, а рукопоп, и прессом перекосит обойму.
The ambient sounds + the camera angle made me think he was making street food.
Didn't you forget to put the key back in the keyway slot?
Hey man
Somebody is gonna have a surprise :)))
Key pen is built on to the shaft
It was there before he put grease oil in at beginning
Это чё у него там, уплотнительная резинка в луже смазки или одноразовая дистанционная шайба из пластика?
Si quieres una de las mejores transmisiones ok reductores averigua está .
распорная шайба...
Men this thing gonna work smoother than my life
I lost it when he blew by putting the key in the keyway and could no longer watch when he hit those bearing races with a steel hammer and socket.
Cycloidal gearbox with what looks like FZ Multemp grease. This gear is normally used in applications that require zero backlash
MORE COWBELL !!!
I dig it baby 😎
Best skit ever.
Тук тук
-это кто?
-это треснутый подшипник.😅😅😅😅
Молодец. А теперь снимай верхний подшипник и меняй. Нельзя их молотком заколачивать.
Ngl I'm more curious about that background Chinese music. Let me know if someone knows.
Very soothing and calming, eh ?
NLG 1 grease or 00 imo ,not very common to see since most parts use the type 2 but I see the mechanism there might require a constant lubrication flow grease tho
Name the Song please ❤❤❤
It's called Peace by Faizal Ishram.
Но мы-то знаем, что такое количество смазки, они кладут только на камеру😁
de los pocos honestos trabajando como es
Looks delicious. Can I have the recipe
Придётся переделать. Шпонку не поставил
Да и по подшипнику молотком.....?
Шпонка стоит.
No pin required, I just beat the snot out of the bearing so it stays in place 😅
Сложилось впечатление, что один из сальников (тонкая резинка большого диаметра) не лёг на своё место.
Ну, с такой смазкой, что угодно будет работать!
А ещё такая жидкая смазка , при нагреве подшипника превратится в воду.
Самое хрупкое в этом редукторе это подшипник с смещенным центром
Наверное вкусный этот джем...🤔🙂😂
If anyone’s wondering, you can find that lemon filling at Dunkin’
😂😂😂😂❤
Вот и молотком по подшипнику, гениально🤣
Да , подшипник ушатал😂
Never hit the outside of a bearing that is the center part that is pressed on. It will damage the balls.
Belíssimo esse vídeo!
Помоему кто-то забыл шпонку под подшипник положить ))))
Yah kitny kv ki motor hy😮
Подшипник молотком забивает. Эх мастер
Everything was fine until he hammered on the outer race. Contrary to popular belief, you can use a hammer to seat a bearing. However, you must ONLY hammer on the race making contact. If you are seating it into a flange, you hammer the outer race; on a shaft, hammer the inner race. It’s intuitive once you understand.
It's a sumitomo cyclo gear box not a auto transmission.
It achieves incredibly low gear ratios the part he is striking in isn't damaged I've assembled hundreds of these.
Хорошая работа, если это будет в выставочном образце 😂
Idk but I'm not a mechanic, but there's something I just love about mechanics, maybe it's just fitting joints perfectly and lubricating; and seeing it works perfectly, and complex fun trying again if not
That's ok this guy ain't no mechanic either
Вот они технологии высшего мира, к прогрессу в пещеры
Столько умных ... Это лёгкие постукивания допустимы!
Машина любит ласку, да смазку!👍
Втулка с закрытыми подшипником наружный подшипник открытый красотень!!!
Все хорошо, кроме молотка по подшипнику)))
В магазине запчастей мне сказали, если увидишь что ступичный подшипник хотят выбивать-забивать молотком- беги оттуда 😁
В наше время туда смазку кладут так же как Гёкче с локтя солит))
Что-то для китайцев смазки больно много!)))
Watching him tap the outer race with a hardened steel hammer made me wince
Железный молоток доставил 😂
Музон прям грабит моё время😂
Мне одному самого начало казалось как будто мёд налил 😂
зато маленький подшипник сухой! 🤣
Der Hammer hat auch noch Kontakt mit dem Aussenring des Lagers, Schaden vorprogrammiert.
Ah yes, the squeaky-bearing-inator.