Thanks for taking the time to explain the difficulties you had, what you did wrong, what you'll try next time etc. Looks like you managed to solve the problems well.
I don't know how to surf, but I love watching all your videos. Maybe someday I will learn. Living in Oregon our costal waters are so cold year round that I don't think it's a good place to learn. Thanks for the great videos.
Awesome video. Seems like eps and epoxy materials easier to get for the backyard builder than poly. Can’t wait to get my shop/tent setup and build a few. Thanks.
YEEEEWWW! Thanks for the video! I can only get EPS blanks in my area (without paying wild amounts for shipping), so it's good to see it done and to hear some of the challenges. Enjoy the ranch! Well deserved!
Awesome video mate! I use only epoxy for my boards, I hate the smell of polyester resin. What you said about sealing the blank: don't do it. In time the board will delaminate, the sealing (q cell especially) won't allow a strong bond between the blank and the laminate. But if you still do it, make sure you seal the whole blank,otherwise you'll have different shades of colour on your board. Also,about your masking tape, gently press it with a spoon when you stick it on the blank. Works like a dream! Enjoy your time at the ranch, maybe the GOAT rides one of your boards! 💪👍
I was going to ask about that too! The only board I've built followed a guide from over 10 years ago & it actually recommended a slight rough sanding for more "tooth". So I too am skeptical of the newer EPS sealing advice but by no means experienced or expert.
Thanks for the tips man. Yeah I’ve heard some seal it and others don’t so I figured I’d save the time doing it. The masking tape was driving me crazy! I pressed it down with the back of my razor but every time it bled through. Never had that issue with poly resin.
@@BendheimBoards I have no experience masking epoxy so no help there. I know guys like Andrew W on UA-cam have had success. I sure like the light weight and durability of EPS / epoxy boards though!
Yew, sweet board once again. I’m currently working on an 8’6 with a black-ish bottom and rail cut lap. Really digging that black pin stripe down the stringer line. Also, glad you showed the relief cuts on the ends, as well the sanding of where the laps crease over before doing the inlay and top lam. Also how you addressed the bleed through. Wish I would have had those on the first two boards. By the second board, I starting figuring out, and to keep sanding until the creases were flat and be careful but not worry too much about the ruining the color and just make it flat. Hard to find any videos where they show those two steps in the process close enough to really see it. Keep up these videos, such great content. And KS’s wave?!? Sweeet, big timing now!
i heard one tip to overcome bleeding is to paint the base color first before painting on the color that you want. i think that's what they do with painting
Sick board man! When i did my first eps i sealed it with microballoons wich worked wonderfull, took some time but it might help with the bleeding lines on the cutlaps. Keep it up :)
still, despite the circumstances with being new to EPS and Epoxy, a dope end result! Enjoy the lighter and more floating aspect of EPS in the wavepool!
If I could ever make a board as good as yours I would be ecstatic, happy as a pig in sh,t you might say lol, awesome job you did mate well done be proud of it , awesome board man.👍
I'm getting ready to glass my first board. Really appreciate your videos. I've been watching them before I go out and work on my board. What do you use to clean up your tools? Acetone?
What is that little pen you use before glassing the top deck? (1:44) What does that help with? Also, is that just a permanent marker at the (2:30) mark? Do you think I should do a white tint on the top deck? I was going to try clear..have you tried going clear on the top? I'm going to glass a board with this same color scheme and I'd be stoked if it came out half as good as yours. Thanks for sharing!
Those are Posca paint pens. I just used them to clean up the color that bled through. You don’t have to color the deck with white, especially if your doing PU foam. This board was EPS foam and I didn’t want the texture showing through a clear coat. If your doing EPS you could also seal the deck to avoid using white.
Hey tanner! Awesome tint job, the board came out awesome. Just wondering, isn’t the board a bit heavy due to the multiple resin layers? See ya! Enjoy surf ranch
What were you using to sand the rough edges between bottom and deck laminations and hot coats? It looked like a stripping disc but not sure. By the way, thank you for making these videos, I really enjoy them!
A couple questions, please.... 1) On my next board (EPS & epoxy) I want yellow rails top and bottom with a clear bottom and deck. I will paint the rails with yellow acrylic before I start glassing. I know how to mask this off when the width of where I’ll apply the paint is the same from nose to tail (kind of like you did at the beginning of this video). Thing is, I want the area on the rails where I’ll paint to get narrower as it approaches the nose and tail. I was wondering if you can suggest an accurate way to mask off this taper so it’s even? 2) Did you buy the black and white markers and pre-cut tape covers for the fin boxes at Greenlight? Your video are the best! Thanks for taking the time to film, edit and upload these.😀 Congratulations on getting to surf Slaters wave!🏄🏻♂️
I’ve never tapered off my cutlaps but I understand what your trying to accomplish. Maybe try measuring how far in you want the colored rails and mark them with dots and then pull your tape connecting the dots. The tape will help you get a more even transition. I used posca paint pens in this video. Each FCS 2 fin box you buy comes with two precut tape covers for glassing which is what I was using. Good luck!
Can you go over how you performed your cut lap? I have attempted one before on the bottom and when I glassed the deck, you could see the places where my razor cut into the blank.
I’m no expert but you want to cut before the board is cured but hard enough to flip. For me it’s around 1.5 hr on poly resin and around 3hr for epoxy. You can cut straight into the rail like me or do what they call a zipper cut which takes some practice. Just keep at it man and learn from the mistakes 🤙
How are you making your hot coats so good? Every time that I’m trying to do hot coats with epoxy I get those weird fish eyes. Anyone know what I’m doing wrong?
Make sure your wearing gloves and not touching the board with your hands. Oils from your hands or other debris like dust can cause it. Greenlight epoxy resin has worked really well for me.
I am glassing a poly board with poly resin and I’m just curious how long the resin should take to fully harden and how long I should wait in between laminations and between the top lamination and the hot coat? And how long I should wait until I sand the hot coat?
@@micahsawyer2055 Check it every 30 min until its ready to flip. Hard enough to be able to flip but soft enough to cut. Maybe an hour to 1.5 hr. I'm having a hard time remembering since I''m working with epoxy and its so much longer now. just babysit it.
@@BendheimBoards ok sounds good! Thank you for the advice. And I just have one more question for you, would you recommend a free lap or cut lap? I’m just a bit worried a free lap might look sloppy but I’ll be using fully clear resin or maybe not, let me know what you think.
![Surfboard Glassing [Retro Fish]](http://i.ytimg.com/vi/iJpIzqaNeZo/mqdefault.jpg)
![Surfboard Glassing [Retro Fish]](/img/tr.png)
![Surfboard Shaping & Glassing [High-Performance Shortboard]](http://i.ytimg.com/vi/rYYuDt8Z2cY/mqdefault.jpg)
![Surfboard Glassing [Shortboard Single Fin]](/img/n.gif)
I gasped when I saw this new upload. These videos are invaluable as I’m trying to shape my own board :)
Stoked! Thanks for the support
I'm hooked on these bro, I hope your channel does well.
Appreciate it!
Dude. A+. I have no idea why I like watching these so much. I just do. The way you shape is cool and the way edit is gold.
Glad to hear it, thanks!
I know nothing about surfing, but seeing his work it's just amazing.
Thanks man!
Gorgeous!!! Love the polished black.
So awesome you get to surf Kelly's pool
🙌
I was rewatching all of your other videos just last night, wondering when this video was going to drop. Stoked to watch when I get home from work!
Awesome, thanks for the support man!
Box
Smk. Type in I
Thanks for taking the time to explain the difficulties you had, what you did wrong, what you'll try next time etc. Looks like you managed to solve the problems well.
Thanks for the feedback 🤙
I don't know how to surf, but I love watching all your videos. Maybe someday I will learn. Living in Oregon our costal waters are so cold year round that I don't think it's a good place to learn. Thanks for the great videos.
Thanks, glad to hear it appeals to people outside of surfing. Hopefully you’ll get a chance one day!
I feel for you ! Had all the same issues w black rail. You did well fixing it. Worth the time investment. Hope you have a great time at the ranch
🤙
Awesome video. Seems like eps and epoxy materials easier to get for the backyard builder than poly. Can’t wait to get my shop/tent setup and build a few. Thanks.
Thanks man good luck with your setup!
YEEEEWWW! Thanks for the video! I can only get EPS blanks in my area (without paying wild amounts for shipping), so it's good to see it done and to hear some of the challenges. Enjoy the ranch! Well deserved!
Thanks man! It had some challenges but that’s expected with the first go. Best of luck with your builds!
Impressive precision when taping the lines! I love these videos, planning to shape my own board soon.
BTW SUUUPER stoked for u (kelly's pool)
Thanks, best of luck with shaping your board!
Can't wait to see that on The waves !!
Maybe in Kelly' ranch. Who knows xD
Also like a color! And I’m jealous of the paint gun !
Thanks just got it! First airbrush and compressor so I’m excited to keep messing around with it.
Great to see a new upload! Dig the new logo on the board too!
🤙
Thx for sharing, nice shape, top design....you will have many good moments with this board for sure. All the best from the Baltic Sea / north Germany
Thank you! 🇩🇪
What an absolute stunner! Well done man can't wait to see it in action. Have a blast at the surf ranch 🤙
🙌
New simple minimal logo looks great
Thanks I appreciate the feedback, I like simple as well 👍
That board looks sick
Love the black and white
I would love a board like that
Thanks man!
I'm not a surfer but love these videos! Keep them coming! You do great work!
Thanks man glad to hear it 🙏
What a amazing job. Board turns out really beautiful. Well done. Amazing piece of art.
🙏
@@BendheimBoards how does it works ? Is it good in the water ? 🌊
@@sambado Yes, works great! Just took it to the surf ranch and had a blast!
@@BendheimBoards Be happy my friend. Enjoy ur piece if art in a man made surf wonder.
Sweet board build bro looking forward to another video enjoy slaters wave pool
🤙
Everytime i watch your videos im like I wish i have that kind of surfboard
Awesome video mate! I use only epoxy for my boards, I hate the smell of polyester resin. What you said about sealing the blank: don't do it. In time the board will delaminate, the sealing (q cell especially) won't allow a strong bond between the blank and the laminate. But if you still do it, make sure you seal the whole blank,otherwise you'll have different shades of colour on your board. Also,about your masking tape, gently press it with a spoon when you stick it on the blank. Works like a dream! Enjoy your time at the ranch, maybe the GOAT rides one of your boards! 💪👍
I was going to ask about that too! The only board I've built followed a guide from over 10 years ago & it actually recommended a slight rough sanding for more "tooth". So I too am skeptical of the newer EPS sealing advice but by no means experienced or expert.
Thanks for the tips man. Yeah I’ve heard some seal it and others don’t so I figured I’d save the time doing it. The masking tape was driving me crazy! I pressed it down with the back of my razor but every time it bled through. Never had that issue with poly resin.
@@BendheimBoards I have no experience masking epoxy so no help there. I know guys like Andrew W on UA-cam have had success. I sure like the light weight and durability of EPS / epoxy boards though!
Your work is really amazing! I am a fan from Brazil. ✌️
Brigado cara, amo Brasil🇧🇷
That board is fire!!! 🏆
Your boards are the best! I’m trying to learn how to shape rn and your videos have been way helpful 🤙🏽
Awesome, thank you! 🤙
Awesome work! Have a great time at Slater’s Surf Ranch! That board should show well out there.
That board came out spectacular, thanks for the video.
Good job!!
Congratulations
Yew, sweet board once again. I’m currently working on an 8’6 with a black-ish bottom and rail cut lap. Really digging that black pin stripe down the stringer line. Also, glad you showed the relief cuts on the ends, as well the sanding of where the laps crease over before doing the inlay and top lam. Also how you addressed the bleed through. Wish I would have had those on the first two boards. By the second board, I starting figuring out, and to keep sanding until the creases were flat and be careful but not worry too much about the ruining the color and just make it flat. Hard to find any videos where they show those two steps in the process close enough to really see it. Keep up these videos, such great content. And KS’s wave?!? Sweeet, big timing now!
Thanks man, really glad to hear that the videos are helping! It’s always a steep learning curve in this industry. Thanks for watching 🤙
The best yet dude! Love it, and can’t wait to see some footage from KS wave pool!
Yew!
Great video once again🤙
I love your videos, keep it up 🤙🏻🤙🏻🤙🏻🤙🏻🔥🔥
parabéns pelo serviço, verdadeiro artista .....BRASIL....
Brigado cara! 🇧🇷
Nice surfboard
Life’s busy, but I wish you had more uploads. Love the videos 👍🏽
Yeah man, wish I had more time too. So many projects going on 🤙
Really really great as always thanks man!!!
love the content
Always inspiring! Good job!
Amazing job!!!!!! 👍👍👍💪💪💪
Great work man. So fresh and so clean!
There you are !!
Conner!! What’s up man! Yeah took forever to get this one done.
Bro you do great job !
Looks nice, good job ✌
That is one dope board!!!!!!!
Beautiful job dude! Nice video :)
Boa man... gostei do trabalho com o pigmento preto... vou fazer assim na minha próxima prancha... parabéns
Legal cara! Brigado 🤙
i heard one tip to overcome bleeding is to paint the base color first before painting on the color that you want. i think that's what they do with painting
Sick board man! When i did my first eps i sealed it with microballoons wich worked wonderfull, took some time but it might help with the bleeding lines on the cutlaps. Keep it up :)
Thanks! Next time 👍
I have a suggestion. In the future you should show footage of you riding your finished product. That’d be pretty cool
Thanks for the suggestion!
Tanx👍👍👍❤️
still, despite the circumstances with being new to EPS and Epoxy, a dope end result! Enjoy the lighter and more floating aspect of EPS in the wavepool!
Yeah man, fun to try new stuff! Can’t wait to get it out there.
Enjoy Kelly Waves Co !!
This was a sick one! Can you do a swallow tail tutorial or a tutorial on how to properly mix resin either epoxy or polyester?
Thanks man, appreciate the suggestions. I plan to make more fishes in the future
Another beautiful build! All new processes take time to work the kinks out. The finished board looks great! How does it ride?
Thanks Jim! I’m nursing a sore shoulder so I haven’t taken it out yet but will break it in next week before the surf ranch 🤙
@@BendheimBoards Get well soon and have a ball at the surf ranch!!!
Turned out well mate. That chat about sealing the blank before 👀... Just kidding haha
If I could ever make a board as good as yours I would be ecstatic, happy as a pig in sh,t you might say lol, awesome job you did mate well done be proud of it , awesome board man.👍
I'm getting ready to glass my first board. Really appreciate your videos. I've been watching them before I go out and work on my board. What do you use to clean up your tools? Acetone?
Acetone works for poly resin and vinegar for epoxy
hey tanner can you do a skimboard build please that would be coo, also great job on the video
One day 🤙
Wish i could ride some of your custom surfboards yeiww 😁🤙
;Your fan from Philippines ❤️
🤙🇵🇭
Amazing video! Maybe you could also show glassing of longboard? :)
That will be my next glassing video 🤙
Hi Tanner - Big fan of your videos, always fun to watch. How did you get the logo print out in white?
I used boardlams.com since inkjet printers don't print white
Hello. Very interesting video. please tell me what kind of markers, pens do you use for touch-up? on what basis is their paint? Thank you.
Posca paint pens. Water based
What is that little pen you use before glassing the top deck? (1:44) What does that help with? Also, is that just a permanent marker at the (2:30) mark? Do you think I should do a white tint on the top deck? I was going to try clear..have you tried going clear on the top? I'm going to glass a board with this same color scheme and I'd be stoked if it came out half as good as yours. Thanks for sharing!
Those are Posca paint pens. I just used them to clean up the color that bled through. You don’t have to color the deck with white, especially if your doing PU foam. This board was EPS foam and I didn’t want the texture showing through a clear coat. If your doing EPS you could also seal the deck to avoid using white.
🤩
Great job and thanx for the video!
Wich cream do you use to polish the board?
Polishing compound from meguiar’s
👏🔥👏
Hey tanner! Awesome tint job, the board came out awesome. Just wondering, isn’t the board a bit heavy due to the multiple resin layers?
See ya! Enjoy surf ranch
The extra bottom gloss coat adds a little weight but the EPS foam is super light and it feels good under the arm
What were you using to sand the rough edges between bottom and deck laminations and hot coats? It looked like a stripping disc but not sure. By the way, thank you for making these videos, I really enjoy them!
3” Disc Pad Holder: www.amazon.com/dp/B07D342TQP/...
@@BendheimBoards thanks!
Great work man, just wondering does the tent contain the polyester resin fume inside the tent? cheers
No, the poly smell will come out
A couple questions, please....
1) On my next board (EPS & epoxy) I want yellow rails top and bottom with a clear bottom and deck. I will paint the rails with yellow acrylic before I start glassing. I know how to mask this off when the width of where I’ll apply the paint is the same from nose to tail (kind of like you did at the beginning of this video). Thing is, I want the area on the rails where I’ll paint to get narrower as it approaches the nose and tail. I was wondering if you can suggest an accurate way to mask off this taper so it’s even?
2) Did you buy the black and white markers and pre-cut tape covers for the fin boxes at Greenlight?
Your video are the best! Thanks for taking the time to film, edit and upload these.😀 Congratulations on getting to surf Slaters wave!🏄🏻♂️
I’ve never tapered off my cutlaps but I understand what your trying to accomplish. Maybe try measuring how far in you want the colored rails and mark them with dots and then pull your tape connecting the dots. The tape will help you get a more even transition. I used posca paint pens in this video. Each FCS 2 fin box you buy comes with two precut tape covers for glassing which is what I was using. Good luck!
@@BendheimBoards Great idea about doing the dots. Thanks!
Could you explain in a video how you did your workshop?
Thank you!!
Already made one, check out my UA-cam page and you’ll find it 🤙
Showwww, muito trabalho né, galera acha que é mole , vlw abçs !!!!!!!!!!!!
Brigado cara! Muito trabalho mesmo! 🇧🇷
Don't forget to take a GoPro to the Surf Ranch!
Haha I have the original GoPro 1 which is probably comparable to a brick cellphone these days
Yoooo do a retro twin in next!!!
Planning to make some this year 🤙
Do you have/ use a chart for resin to catalyst ratio based on temp and humidity? Or just mix it the same no matter?
I use the greenlight resin chart. if its hotter, its going to cure faster, especially for poly resin
Do you think I could spray paint the rails before hot coating?
You'd have to do it either on the foam blank or after the hot coat, but not on the lamination
So how did the trip to Surf Ranch go? Did the board perform well?
So much fun man, yes the board works great. Tested it in Hawaii a week ago as well
@@BendheimBoards awesome! That is way cool that you shaped your own and surfed it, aaannd it turned out great. Super pumped for you. Congrats bro!
Are you waiting until the resin dries before applying the hot coat?
Can you go over how you performed your cut lap? I have attempted one before on the bottom and when I glassed the deck, you could see the places where my razor cut into the blank.
I’m no expert but you want to cut before the board is cured but hard enough to flip. For me it’s around 1.5 hr on poly resin and around 3hr for epoxy. You can cut straight into the rail like me or do what they call a zipper cut which takes some practice. Just keep at it man and learn from the mistakes 🤙
How are you making your hot coats so good? Every time that I’m trying to do hot coats with epoxy I get those weird fish eyes. Anyone know what I’m doing wrong?
Make sure your wearing gloves and not touching the board with your hands. Oils from your hands or other debris like dust can cause it. Greenlight epoxy resin has worked really well for me.
hello, does the epoxy resin not melt the eps foam?
Correct
🤙🏼
Some Spackle on the boarder of the tape on the foam side you are glassing might help ya w the bleeding
🤙
Hey , please i want to know how much kilo of resine epoxy u need to glass this surfboard?
Depends on the size of the board. Greenlight surf has resin charts you can use
I am glassing a poly board with poly resin and I’m just curious how long the resin should take to fully harden and how long I should wait in between laminations and between the top lamination and the hot coat? And how long I should wait until I sand the hot coat?
I always work at night and then come back to it the following night. Never need to wait longer than that for all steps mentioned
@@BendheimBoards Thank you for the help! Also how long does it take for the poly resin to become the perfect consistency to cut the laps?
@@micahsawyer2055 Check it every 30 min until its ready to flip. Hard enough to be able to flip but soft enough to cut. Maybe an hour to 1.5 hr. I'm having a hard time remembering since I''m working with epoxy and its so much longer now. just babysit it.
@@BendheimBoards ok sounds good! Thank you for the advice. And I just have one more question for you, would you recommend a free lap or cut lap? I’m just a bit worried a free lap might look sloppy but I’ll be using fully clear resin or maybe not, let me know what you think.
@@micahsawyer2055 Freelaps are used for clear resin. If your worried about it you can do a cutlap, it just takes a little more prep work.
At what point would you put glass on fins on? Before or after hot coat?
Before hot coat then hot coat the board and fins.
@@BendheimBoards Awesome thank you! Also do you suggest buying one of those clear measuring tools for fin placements?
@@micahsawyer2055 For sure, I use the Terry Senate Fin marker and it makes it super easy.
Any idea why you had so much bleed through on the tape?
Not really, if I had to guess it’s gotta be the difference between EPS/epoxy and PU/poly. Never had these issues with PU/poly.
Is this classified as a sanded gloss finish? Or is it just a sanded finish? Thanks!
I want this item
What colour paint you mix in epoxy resin?
Black on the bottom and white on the top
Which tool using the glassing
Epoxy resin 🤙
Is this the one based off the Fever?
Shape is based on the Channel Islands Sampler
@@BendheimBoards Ah, I thought it was the Channel Island Fever ;) But Sampler, cool :D
Hola soy de Panamá como se ordena una tabla con ustd
Sorry don’t have any for sale right now 🇵🇦
Whats the name of the first instrument in the video???😅
Marking gauge from Foam EZ
Do you sell these boards you make?
Not yet but probably will once I outgrow my quiver and friend projects
Was that a pu blank or eps?
EPS
@@BendheimBoards how was it shaping
@@donaldknoth6705 Great, didn't mind it for shaping. I still prefer PU since you get that fine sanded finish and it works better with glassing.
Bang maskernya namanya apa
You are a wonderful person. But can you give me the materials to make it?