Surfboard Glassing: How to do a Freelap Bottom Lam with Chris Bauer

Поділитися
Вставка
  • Опубліковано 24 гру 2024

КОМЕНТАРІ • 17

  • @stephenbrown664
    @stephenbrown664 Рік тому

    This guy is a pro.. Awesome to watch. Thanks for sharing your technique..

  • @cabacronulla
    @cabacronulla 3 місяці тому

    Been a Glasser since 1977...This guy is PRO!!!! Way back No Gloves or Mask....My skin is stuffed...

  • @jobhiojkp
    @jobhiojkp 7 місяців тому

    Wow, the photographer stuck to him like glue to get fantastic closeups during the whole wetting out process. BTW, from 10:37 - 10:40 I seem to see a lot of wet "stringies" hanging down from the rail and I'm surprised he doesn't cut those off. Surely he's not going to lap them around to the deck. They always cause so much trouble when glassing the deck. OK, so I watched some more, and he lays them down parallel to the rail and not out onto the deck. BTW, photography at 13:28 is incredible; you can see the drips so clearly! Kudos to the cameraman!

  • @preplan1
    @preplan1 10 місяців тому

    With the 7533, is that inches, making it over 600 feet of fiberglass? Thanks. Great video 🤙🏽

  • @Sswervyy
    @Sswervyy 2 місяці тому +1

    so how come he doesnt tape off the deck of the board so that the resin doesnt get all over the deck when he wraps the rails?

  • @mauricioreyes9756
    @mauricioreyes9756 2 місяці тому

    How much resin did you use for the bottom?

  • @johnstokes6301
    @johnstokes6301 2 місяці тому

    How much resin are you guys using per foot of board?

  • @matthewwillis4892
    @matthewwillis4892 Рік тому

    Bauer Power🤙!

  • @henrye718
    @henrye718 8 місяців тому

    If I chip brushed then rolled and then used a bubble busting roller could i use this method on 1708 without priming board with resin first. When i say board i mean a piece of lumber. Thanks for the videos!

  • @davebolt1614
    @davebolt1614 Рік тому

    When he adds a lil more resin to the bottom, is that from the same bucket or does he mix up a bit more ?

  • @ivydune4185
    @ivydune4185 9 місяців тому +1

    How did he have so much time? 9 minutes working with the same resin without it hardening?

  • @federicotatoni6829
    @federicotatoni6829 10 місяців тому

    how much resin do you usually use for each layer of fiber glass (depending on the length of the board of course)?

  • @tylermorris5463
    @tylermorris5463 Рік тому

    what squeegee does he use? that one looks nice a big but flexible

  • @ichorousmedia
    @ichorousmedia 11 місяців тому

    always picking up new techniques. I feel like I'm always trying to keep my hands as clean as possible until the very end, but hes just going at it saturating laps with is hands...gotta try this as this is my weakest glassing step. I would love to have all that extra time to lay down more resin on the deck and babysit laps

    • @clintjones9848
      @clintjones9848 11 місяців тому

      Imo, you're shooting yourself in the foot if you don't do the continuous rail waterfall and saturate each lap completely in 1 stroke. It's a bit more wasteful with resin, but is so much more efficient with respect to laminating the board. What I do is lay the stickers, then pour a little bit in the middle of the board, spread it out quickly and get the glass to adhere, then immediately go to lap resin waterfall. After that you're good to go, you only need a little resin left in your bucket to make sure everything is smooth on the flats and then tuck the laps.

  • @sealanimccall1787
    @sealanimccall1787 Рік тому

    Hey why did he have a double lap at the tail of the board? Thanks!

    • @mrpopular6185
      @mrpopular6185 Рік тому +2

      It's to reinforce where the fin box will go 😁👍