Products that we use and recommend: ► Find Parking Brake Switch for your car here: amzn.to/2Zmi89T ► Panel Removal Set: amzn.to/3YiMADu ► Tool Set: amzn.to/3p5MM6t ► Screwdriver Set: amzn.to/3XRB28Q ► Castrol Oil: amzn.to/3xBc8B9 ► Oil Filter: amzn.to/3w0Ulme ► Torque Wrench: amzn.to/32qyRwg ►Liqui Moly Engine Flush: amzn.to/3IiDBID ► OBD Scanner that we use most often: amzn.to/3I4MQfe ► Check out our Amazon Store for the tools and parts that we use: www.amazon.com/shop/worldmechanics
Most of the people on here taking the piss out of the way he speaks... Failing to realise he speaks more than one language and English is not his first, pretty sure most of you negative talkers can just about speak one language. Thanks for the video
I think the objective of this video is: 1: Locate the switch 3:20 2: Replace the switch OR entire petal/handbrake ratchet assembly. 👍It doesn’t show how to troubleshoot (clean, lubricate, realign, or fix a sticky switch) which might often be good enough to fix an old malfunctioning switch; which you should try once the switch is located. The end of the video 👎 shows how to disconnect the sensor/dash-light indicator 🤦♂️ (yes I hear the disclaimer in narration, however this is irrelevant to FIXING anything). It’s still helpful but that’s my feedback. Thank you
I have a 2020 Miata and lately when I make a turn it comes on for like a second and it's been doing this for a little while, I wish I knew what it was, my brake fluid is full so I don't know
@@juliacaraballo8987 After several months of topping up and the light coming back on - I have no idea why yours hasn't gone out - our mechanic found the cause was a corroded brake pipe. Fixed and no problems since. Maybe your problem with the light is simply a case of following this quack's method of getting the light to stay off!
Urgent advice needed. My light goes out if the wire connects to an earth but that's what it's supposed to do but unfortunately it is fooked and stays on no matter what. Only other function is brake fluid level but that is fine. Wtf . This is driving me nuts.
I have the same issue, and I am a millwright mechanic. As the brakes wear it requires more brake fluid in the system to fill the volume of fluid inside the brake calipers. You will notice that every so often you need to add a bit more to your brake reservoir because the level has dropped near the lowest level indicator. On a manual transmission car (I have) such as a 2013 or newer Hyundai, the clutch hydraulic mechanism is also fed from the brake reservoir. Topping up the reservoir will temporarily correct the light from staying on after the E brake is disengaged. Just be careful when replacing the brakes. You may have to remove some of the brake fluid that you previously added to prevent it from spilling over the top of the reservoir when you push the caliper pistons back far enough to install the new brake pads. This is purely a design issue with some cars that has obviously been overlooked to keep the cost of the car lower. The car I am referring to is my wife's 2013 Hyundai Elantra with standard 6 speed trans, with just under 50,000 Km. The brakes are original and I have added brake fluid 3 times to date. (Feb 14, '23) to get the light to stay off. We will be checking all four brakes as soon as the weather "brakes" in March.
@@arthurrimbaud7287 I fixed the issue. It had to do with one of my brake sensor went out, replaced it while I was doing my brakes and the light went off. Check your brake sensor might need to be replace.
I need help guys! How do I check to see why my dash brake light is ALWAYS off, even if the parking brake is pulled up (on)? Is it something to do with the switch or is it most likely the bulb in the dash? It’s a ‘03 Mazda Protege. I don’t know where to start…
MY HONDA CITY CAR 2004 MODEL BRAKE LIGHT COMES ON WITH THE TEMPERATURE GREEN AND RED LIGHTS, AND THE SPEEDOMETER AND ACCELERATOR METER CUT OFF WHEN THE CAR GOES ABOVE 60 KM SPEED, NO The check light comes on and the engine does not turn off, can you tell me what the problem is
Got Nissan Xterra. After driving for about a min my parking brake light comes on , along with the 4x4 light and my screen that shows 4x4,2x4 …. selection goes blank. Any ideas
Low brake fluid in the reservoir. Don't add too much ! It may overflow at brake job time. I have 2013 Hyundai (50,000 K) Under the hood to the right of centre near the firewall. Black round screw-on cover👍Problem is NOT the switch ! Been there done that. 🤔😑
I have a 2006 Volkswagen Beetle that had a brake light on, and it's causing my headlights to no turn on. Im driving around at night with nothing but the driving lights on. Argh. Anyone know how i can fix this?
Depends on the problem. If you feel like your handbrake is not engaging also known as not working properly or If you are feeling like the handbrake power is lower than usual then It's a big problem, you can drive but It's a major safety hazard and is highly not recommended to drive ! But If you are feeling like nothing has changed and the handbrake power is like usual then It's safe and the handbrake light might be showing because the light trigger malfunctioned or got stuck and Is an easy low cost fix.
2002 ford explorer/ Unplugged wire to parking brake switch, light still on, installed new switch, light still on/ no voltage coming from terminal wire that goes to switch? Flashes on and off some times.
Depends on the problem. If you feel like your handbrake is not engaging also known as not working properly or If you are feeling like the handbrake power is lower than usual then It's a big problem, you can drive but It's a major safety hazard and is highly not recommended to drive ! But If you are feeling like nothing has changed and the handbrake power is like usual then It's safe and the handbrake light might be showing because the light trigger malfunctioned or got stuck and Is an easy low cost fix.
Please can you help me? I have a Toyota echo 2003 the handbreak works fine but when I take the handbreak off the light still stays on. How do I get the handbreak light to go off? I just checked my break fluid and it was low but I filled it up and the handbreak light is still staying on. Any ideas anyone? Please send help 🙏
Omfg this guys voice and the way he talks makes my skin crawl.ill take the car problems over having to listen to this guy try speaking English anytime of the day.this is the new way of torture in 2020
These videos are all very informative and I appreciate the knowledge I gain from them, but I can't stand his loogie in the throat voice and the million times he says " guys" and "ok". Rest in peace to my ear drums while wearing headphones at the start of this video. SMH
If your stop saying 'ok' and 'guys' every third word it makes it a lot easier to understand what you are trying to say. I realize that English is not your first language but your English is very good except your overuse of ok and guys. At least you don't use the word 'like' all the time.
STFU , if you don't have anything good to say then shut your trap ! Talking sh*t is your strong hold! F**** loser . You seek help on UA-cam then talk sh*t. Go kick rocks a$$ wipe
English isn’t his native language, asshat. Why don’t you try to speak a second language and see how perfect you can do it. Not a big deal, especially considering this guy is constantly pumping out great content and helping people diagnose/fix a huge variety of car issues. Touch grass, retard.
Products that we use and recommend:
► Find Parking Brake Switch for your car here: amzn.to/2Zmi89T
► Panel Removal Set: amzn.to/3YiMADu
► Tool Set: amzn.to/3p5MM6t
► Screwdriver Set: amzn.to/3XRB28Q
► Castrol Oil: amzn.to/3xBc8B9
► Oil Filter: amzn.to/3w0Ulme
► Torque Wrench: amzn.to/32qyRwg
►Liqui Moly Engine Flush: amzn.to/3IiDBID
► OBD Scanner that we use most often: amzn.to/3I4MQfe
► Check out our Amazon Store for the tools and parts that we use: www.amazon.com/shop/worldmechanics
😁
1qqqqq1qqq
Most of the people on here taking the piss out of the way he speaks... Failing to realise he speaks more than one language and English is not his first, pretty sure most of you negative talkers can just about speak one language. Thanks for the video
exactly
👏👏👏
Nah
I'm not bashing on how he talks its just how many times he says ok I think is funny I think the guy is highly educated
he still explained it enough for me to understand 🤷🏽♂️
I think the objective of this video is:
1: Locate the switch 3:20
2: Replace the switch OR entire petal/handbrake ratchet assembly.
👍It doesn’t show how to troubleshoot (clean, lubricate, realign, or fix a sticky switch) which might often be good enough to fix an old malfunctioning switch; which you should try once the switch is located.
The end of the video 👎 shows how to disconnect the sensor/dash-light indicator 🤦♂️ (yes I hear the disclaimer in narration, however this is irrelevant to FIXING anything).
It’s still helpful but that’s my feedback. Thank you
Literally what i was thinking…
Video was useless for me yeah
Let’s make a tutorial video of how to fix something, but not really give any clear instruction, except for one little don’t do.
Thanks for your help it help me find my problem just wiggle The Wire
Much love from California, Mazda 3 2.5L 2010 gang
Badass man. You saved me a lot of money. Thank you!!!
He said Okay 34 times
okay 😂😂
I think he said "guys" around 3400 times but I lost count after a bit...
Okay
I like it when someone says "I'll show you this but never ever do it". That's what gets my attention🤣🤣🤣
From Ghana it really helps me thanks
Such a simple fix, once again guys thanks
Where did you went to get a new one so fast 😅 great idea of reusing the new part
Great video!
He disconnects the wire @3:50
I love your videos. Great Job.
Excellent advice, thanks!
I definitely won’t be cheap and fix it the easy way😂😂
I’m definitely not going to do that right now 😂
stop alarm plus handbrake warning light turan
I know this video wouldn't apply to a 1991 Jeep Wrangler but my brake light is on & I've replaced the brake light switch & its still on...any advice?
I have a 2020 Miata and lately when I make a turn it comes on for like a second and it's been doing this for a little while, I wish I knew what it was, my brake fluid is full so I don't know
Similar problem. 2008 Ford Focus
Brake fluid needed topping up and the light went out immediately.
It's still on.. After brake fluid topped up
@@juliacaraballo8987 After several months of topping up and the light coming back on - I have no idea why yours hasn't gone out - our mechanic found the cause was a corroded brake pipe. Fixed and no problems since. Maybe your problem with the light is simply a case of following this quack's method of getting the light to stay off!
Thank you!
Urgent advice needed. My light goes out if the wire connects to an earth but that's what it's supposed to do but unfortunately it is fooked and stays on no matter what. Only other function is brake fluid level but that is fine. Wtf . This is driving me nuts.
😂😂😂”ok”
Lmaoooo
So, ok, ok? Thank you. Ok😀 ok! Very good, ok! Ok, ok, ok
2:05
How about abs traction lights on ?
Lol why do they talk like that 🤣🤣🤣 remind me of Talladega Nights
Nice video
If I had a dollar for everytime he says "guys", I could buy a Mercedes🤣😂🤣
Topping up your brake fluid reservoir could do the trick ! I'm not sure why . Cheers Eddie PS Mark down below also found this 'fix'
I have the same issue, and I am a millwright mechanic. As the brakes wear it requires more brake fluid in the system to fill the volume of fluid inside the brake calipers. You will notice that every so often you need to add a bit more to your brake reservoir because the level has dropped near the lowest level indicator. On a manual transmission car (I have) such as a 2013 or newer Hyundai, the clutch hydraulic mechanism is also fed from the brake reservoir. Topping up the reservoir will temporarily correct the light from staying on after the E brake is disengaged. Just be careful when replacing the brakes. You may have to remove some of the brake fluid that you previously added to prevent it from spilling over the top of the reservoir when you push the caliper pistons back far enough to install the new brake pads. This is purely a design issue with some cars that has obviously been overlooked to keep the cost of the car lower. The car I am referring to is my wife's 2013 Hyundai Elantra with standard 6 speed trans, with just under 50,000 Km. The brakes are original and I have added brake fluid 3 times to date. (Feb 14, '23) to get the light to stay off. We will be checking all four brakes as soon as the weather "brakes" in March.
Mine just comes on when I hit the brake hard enough. I check the fluid it look good any idea!? Thank you
this is my issue on my bmw e90 can’t seem to turn it off. What could be the fix?
Is your car driving fine otherwise?
@@arthurrimbaud7287 I fixed the issue. It had to do with one of my brake sensor went out, replaced it while I was doing my brakes and the light went off. Check your brake sensor might need to be replace.
Is anyone ever told you that you use “Ok” too many times, an sometime for no reason.
Thanks for the video, great video.
I need help guys! How do I check to see why my dash brake light is ALWAYS off, even if the parking brake is pulled up (on)? Is it something to do with the switch or is it most likely the bulb in the dash? It’s a ‘03 Mazda Protege. I don’t know where to start…
hey i short out the parking light and low beam by accident how do i power it thanks
A fuse ? Lmaoooo
MY HONDA CITY CAR 2004 MODEL BRAKE LIGHT COMES ON WITH THE TEMPERATURE GREEN AND RED LIGHTS, AND THE SPEEDOMETER AND ACCELERATOR METER CUT OFF WHEN THE CAR GOES ABOVE 60 KM SPEED, NO The check light comes on and the engine does not turn off, can you tell me what the problem is
GO TO A MECHANIC
Okeeee..okeeee....okeee
Can i ask something ? How to remove "parking brake is applied" at the meter reading ? Audi q7
Okay.
Got Nissan Xterra. After driving for about a min my parking brake light comes on , along with the 4x4 light and my screen that shows 4x4,2x4 …. selection goes blank. Any ideas
Video starts at 2:45. ffs
Thanks!!!
Clutch
ty
Hey guys, I just replaced the e-brake switch and it didn't fix the light staying on the dash. 2012 Hyundai Elantra gls. What should I look for next?
Low brake fluid in the reservoir. Don't add too much ! It may overflow at brake job time. I have 2013 Hyundai (50,000 K) Under the hood to the right of centre near the firewall. Black round screw-on cover👍Problem is NOT the switch ! Been there done that. 🤔😑
My Brake light comes on when I go round bends … slow on approach .. bloomy thing stays on … help 😮
What happened?
Okay
Your favourite word is okay ? 😂😂😂🤔
👍
I have a 2006 Volkswagen Beetle that had a brake light on, and it's causing my headlights to no turn on. Im driving around at night with nothing but the driving lights on. Argh.
Anyone know how i can fix this?
FOR GOD'S SAKE, STOP SAYING "GUYS!"
Is it safe to drive if the lights still on?
I’ve been driving with it on for like a year 😅
Depends on the problem. If you feel like your handbrake is not engaging also known as not working properly or If you are feeling like the handbrake power is lower than usual then It's a big problem, you can drive but It's a major safety hazard and is highly not recommended to drive ! But If you are feeling like nothing has changed and the handbrake power is like usual then It's safe and the handbrake light might be showing because the light trigger malfunctioned or got stuck and Is an easy low cost fix.
oke disconnect the park brake switch wire oke got it oke thanks!
Ooooooook.
But my hyundai sonata 2002 when I release the handbrake the light goes off from the dashboard but after driving for about 1 mile it shows up again
Where elantra boys:(
2002 ford explorer/ Unplugged wire to parking brake switch, light still on, installed new switch, light still on/ no voltage coming from terminal wire that goes to switch? Flashes on and off some times.
Hi I have the same problem did you fix it?
Can we still drive if this light is on? Is it safe
Depends on the problem. If you feel like your handbrake is not engaging also known as not working properly or If you are feeling like the handbrake power is lower than usual then It's a big problem, you can drive but It's a major safety hazard and is highly not recommended to drive ! But If you are feeling like nothing has changed and the handbrake power is like usual then It's safe and the handbrake light might be showing because the light trigger malfunctioned or got stuck and Is an easy low cost fix.
I put car switch off but handbrake Still light on
So they only got light to go out by dissconecting wires! Madness and a waste of time! 😅
Please can you help me? I have a Toyota echo 2003 the handbreak works fine but when I take the handbreak off the light still stays on. How do I get the handbreak light to go off? I just checked my break fluid and it was low but I filled it up and the handbreak light is still staying on. Any ideas anyone? Please send help 🙏
My park lights are on and want go off .What do I do
can i get a future video in english?
Probably got a blown fuse?
Okee okeeeee
Ok guys
"OK"
Ok guys, cool ok. Ok guys thanks guys, ok... ok.
Why teach someone to do something and then say don't do it😂
i fixed my brake light problem by putting black tape over it so i dont see it on anymore, easy fix
Is it still working?
Okay, okay, okay, guys, okay, okay, okay, guys, okay, okay, okay, guys ...
I bet you a buck you’re from Switzerland....that totally sounds like a German Swiss accent....
Sounds eastern European to me
ok
Thank u bro
Omfg this guys voice and the way he talks makes my skin crawl.ill take the car problems over having to listen to this guy try speaking English anytime of the day.this is the new way of torture in 2020
Borat's revenge!
Wow youre a real peachy guy
Just skip all video
ok, ok, ok
If that the case, why you still teaching the wrong method?
These videos are all very informative and I appreciate the knowledge I gain from them, but I can't stand his loogie in the throat voice and the million times he says " guys" and "ok". Rest in peace to my ear drums while wearing headphones at the start of this video. SMH
I was thinking exactly the same. It's "OK guys" after every four or five words. Very annoying.
I never wanna hear this guy talk again.
GUYS GUYS GUYS GUYS GUYS GUYS GUYS GUYS GUYS GUYSGUYS
ohkee
hello
Ook
No help
If your stop saying 'ok' and 'guys' every third word it makes it a lot easier to understand what you are trying to say. I realize that English is not your first language but your English is very good except your overuse of ok and guys. At least you don't use the word 'like' all the time.
STFU , if you don't have anything good to say then shut your trap ! Talking sh*t is your strong hold! F**** loser . You seek help on UA-cam then talk sh*t. Go kick rocks a$$ wipe
Rubbish Its not the switch @ fault in my case
ok ok ok ok ok
😈 do not do this.
stop saying “guys” every 5 seconds or every other word.
English isn’t his native language, asshat. Why don’t you try to speak a second language and see how perfect you can do it. Not a big deal, especially considering this guy is constantly pumping out great content and helping people diagnose/fix a huge variety of car issues.
Touch grass, retard.
Okay
Okay