If your like me and goes straight to comments: 1. Open the top cover 2. quickly press (back arrow) button & (red x) button at the same time - dont hold, just a quick 2 button press will do 3. IMMEDIATELY press the back button 4. Select the cartridge color you want to reset the count for Thanks for sharing this great video
Latest update: my printer is relatively new, this is first toner change necessary. I tried this and read others similar. I found that it just would not work, despite repeatedly trying. Finally, I picked up someone else’s comment as follows: this procedure with the buttons only works (or not) on the first try after opening the top, if you miss the first try it will never work - you MUST close and reopen the lid. I had given up and then read this the next day, went and gave it a go…magic, worked first time.
Yes. This does work. It worked for my yellow and magenta cartridge. Still having issues with getting the black and blue to reset. I had to actually unplug and wait a bit to try again for it to reset though. I'll try again for the black and blue.
Thank you so much! This video literally changed my life! I was down-and-out, living on the streets, barely scraping by- fast forward to ten minutes after I watched this video: I just purchased a new home and a mid-sized sedan! I can't thank you enough!!!!
I read about five other FAQs and watched two videos and none of them worked. The press at the same time and keep doing it until it popped up works EVENTUALLY one time but by the time I got it work I had to look at the next step and lost it and couldnt' replicate. This method was WAY MORE RELIABLE. Thank you.
Thank you so much! I was able to do my older printer but this new one I could not figure out. It's amazing how many more pages you can print when you do this. Thank you again!
Thanks for the tip! Everything on the internet about resetting this printer's toner counter was wrong (said hold the two buttons for two seconds, which doesn't work), but thank goodness your video was *right*.
Thank you so much! Instructions online were not clear and your video worked for me. I don't have the higher end model like yours but rather the HL-L3230CDW and this worked perfectly.
Worked great. Have version 1.30 and my black cartridge was just showing low, not out. Important step missing is how to get to the screen shown at 1:53. For me... I opened cover and then at top of lcd screen was little white on black textbox that says "Cover is Open >". Had to click on that little black textbook to get to same same screen as 1:53. After that I could follow your steps. Thanks OP!
Updated to the lastest firmware on my L3270CDW as of 1/20/24 (V1.35 MAIN, V1.14 SUB1) and this toner reset method works just fine. Remember, there's also a battery on the toner drum chip that can go bad, as well as a mechanical switch that flips when the toner drum claims to be empty. Each of those can trigger the replace toner error.
Just want to thank you. I had enough toner for hundreds of pages left in the printer, but after a system restore the toner showed as nearly empty. That would have been two hundred Euros to print a few pages. Brother ought to put this information with the printer.
Thank you so much for your help. I canceled the cartridge order. My black cartridge showed full to the top after I reset it. Great instructions, I played your video a couple of times and paused it as need it. I did try a couple times as the first time the screen arrows didn't work so it took me off the reset screen. We just have to be patient, follow the directions and try a couple times. Thank you again.
I've just tested and it still works, thanks a lot. ( firmware versions : main version 1.30 - sub1 version 1.13 ). It did not work at the first try.. I had to repeat it several times and as described in the comments I had to close and reopen the lid until it worked. The order of the buttons was back 1st then cancel, then release then back.
Thanks a bunch! I mistakenly installed the black cartridge into the wrong slot when changing 2 colors. The black cartridge thereafter was being read as empty, when in fact it was brand new. Multiple attempts to reset (just like you said) were unsuccessful. Your method worked perfectly on my MFC 8900 CDW.
Thanks for this it worked perfectly apart from one extra step - when I opened the cover a yellow bar on top of the screen indicated the cover was open and I had to tap on the car to get the same screen shown in your video. After that it was exactly as described in the video.
Thanks a lot, it was a little bit complicated for me in getting the reset menu. Hopefully, following will be clear for others. Toner reset menu : 1.Open printer cover 2.Keep screen on yellow page (cover is open) 3. press Back + x (no need to hold) Release both, then immediate press back. Then rest is shown in the video.
Thanks a lot!!! This worked. The problem I was having is the new cartridges were not registering as new and the printer was saying to replace the cartridge.
THANK YOU FROM HEART, I'VE BEEN LOOKING FOR SO LONG FOR THIS PROBLEM. I HAVE THIS PROBLEM WITH NEW CARTRIDGES, sometimes it gives the black another time the yellow, although i didn't print even 50 pages!!! I heard about using a tape on one side of cartridge and so you can stop printer from counting the number of pages? I am a subscriber indeed, your way of explaining is very simple and clear. Best wishes. Thank you in advance for your reply about the tape thing. Friendly regards
This is a great tip. Thanks so much. My problem is that I have replaced a toner cartridge and the machine is stuck with an error message of No toner. Any suggestions. I have tried many of the suggestions found online but nothing is fixing this issue
@@rockergirl2489 i bought and replaced my generic print cartridge with branded print cartridges and this fixed the issue. I was able to isolate the issue down to a single generic print cartridge but replaced them all with branded to avoid any future hassles.
@@aaronpen21 thanks for that - the black one is the only one displaying empty and they are all generic cartridges. I will get the Brother black one and fingers crossed that will do it. Thanks for your help 😊🙏
Excellent explanation and thanks for showing the cleaning of the corona wire, although its literally RIGHT THERE, i probably would have missed it otherwise. Great to know you can save money on these cartridge's. I don't know that there is a way to do a reset on inkjet cartridges, thus i'm switching to laser.
This is a great video for resetting the toner cartridges; very sorry it did not help me though. My L3270CDW is saying "NO TONER" and although I was able to reset all the cartridges (quite a few times) I just cannot get it to work. And the screen continually says "Cover open". Someone commented on this and said they hit the "car" to get rid of it???? Firmware 1.33/1.14.
I’m glad I was able to help. I looked for days trying to find out how to reset it and stumbled onto the solution by trying a combination of what others were saying worked but didn’t.
Good morning, I tried to carry out this process on my hll3240cdw, but when I try to enter reset mode, it stays blank, nothing appears, as if there was another command missing. Would you know how to reset the cartridge on this machine?
amazing thank you. I got a new Magenta Toner that is supposed to be compatible but it's not recognizing it. this will get me thru while I work out how to get it to work. Any ideas??
Hola ! Tengo la impresora HL L3280CDW (es la misma que esta, pero el panel totalmente touch) y no me funciona 😢 conoce algún otro método o deberia funcionarme de igual manera ?
I followed the steps and reset my toners. However, it still indicates, "Open the top cover and then install toner cartridge." I would appreciate any suggestions.
hey.. it did work for some time, but it now it stayed low, after replacing new (not original) toner. It pretends that tonercounter reset is accepted, but it stays at low value, tried with different drums too
Great film material. For me, the problem was a little different. I had a "no toner" error without color specification. I followed the procedure according to the movie without success. Later I reset the printer to the factory settings - without success. I still had a "no toner" error. I remembered that I had one magenta toner in stock (not original) - I put it in the printer and fixed error - printer works. The error has disappeared. My firmware 1.27. The toners were about 50% of the toner level. It happened after a few days of disconnecting the printer from the power supply. Maybe it will help someone.
stopped printing. saw that black was low. bought a new one $80 (wow) installed. slid the slider. still wouldn't print. i went through the process and reset the counter for ALL the cartridges. still NO TONER. any suggestions?
Ici, j'ai réinitialisé les 4 niveaux d'encre -ce qui apparait bien sur les graphes-, mais indique en sus : "l'encre de l'imprimante est peut-être épuisée"; Bref - ça ne marche pas pour moi :-(( Une idée ?
I've successfully completed this toner counter reset before. But recently Brother updated the printer firmware and now when I complete the process and the reset is 'accepted' the toner color bar remains empty and the printer will not print. Any suggestions on how to fix?
My understanding is if you update the firmware this will not work. I am not updating my firmware and it is still working for me. Sorry you are still having issues.
I have updated my 3770cdw for several times and this working like a charm.. did you hold the back+cancel button for long time or just instant? I tried the long push didn't work, but the instant tap back+cancel then the back do works
@@ridwan2706 your method is the one that actually worked for me. When I instantly pushed both back and cancel together and then the back button fairly quickly it worked. Thank you so much for your comment!!
I have the same issue here. But it amazes me that nobody blames the Brother printer for this stupid mess. Everyone just accepts it and tries to find a way to bypass it.
This worked for me, but one question.... Once I really do have to replace the toner cartridge, will I need to reset the counter again? Or does the printer do this automatically when the cartridge is actually replaced?
CAREFUL! After upgrading to the latest firmware (1.27), this method no longer works! It still lets you access the menu, but even after resetting the cartridge, it still tells you to replace the toner and refuses to print. I still haven't found a workaround and according to Brother and the Internet, it is not possible to downgrade the firmware back to its previous version. Very infuriating...
Sorry to hear that. I have not updated mine and this method still works for me. Thank you for the heads up on updating the firmware. Hope that will help others from not updating unless they understand the consequences.
I have 1.27 and the process worked for me. Took a bunch of tries to get into the reset menu, but eventually succeeded and was able to do a reset (I reset both BLK entries, just to be sure). Printing is restored!
I have the same issue. The whole thing seems a bit broken. It thinks my magenta cartridge is full despite significant printing, but my yellow is apparently empty and no amount of hitting reset is fixing it.
thanks for the video. I got the "No toner. open..." error. Following your instructions i reset all counters and was hoping that then the error was gone as all cartridges have been replaced. But printer still thinks i need to place toner. It wont even tell my wich one an dthe funny poart is when i go to the toner life menu item...it shows all cartridges as full...
Thanks for the tutorial. Just one thing. When I opened my cover, the cover open screen didn't look like yours. It had a cover open notice, but it also showed other printer information. I had to press the 'cover open' message after opening the cover and then I ended up with the same 'cover open' screen that you had. If you do not have the single message of 'cover open' on the screen, the button pressing reset won't work.
If your like me and goes straight to comments:
1. Open the top cover
2. quickly press (back arrow) button & (red x) button at the same time - dont hold, just a quick 2 button press will do
3. IMMEDIATELY press the back button
4. Select the cartridge color you want to reset the count for
Thanks for sharing this great video
I did exactly that. Reset all the toners, says "accepted" but then nothing happens.
Not all heroes wear capes!
Latest update: my printer is relatively new, this is first toner change necessary. I tried this and read others similar. I found that it just would not work, despite repeatedly trying. Finally, I picked up someone else’s comment as follows: this procedure with the buttons only works (or not) on the first try after opening the top, if you miss the first try it will never work - you MUST close and reopen the lid. I had given up and then read this the next day, went and gave it a go…magic, worked first time.
Glad it worked for you. Thank you for watching.
Yes. This does work. It worked for my yellow and magenta cartridge. Still having issues with getting the black and blue to reset. I had to actually unplug and wait a bit to try again for it to reset though. I'll try again for the black and blue.
Here I make several times without close the door - until It display toners options.
@@theknoxvillepicker I go through these steps it says accepted but then doesnt reset any advice?
How would I know my toner is std or hc to reset or can I do both std&hc rest at a time.
Thank you so much! This video literally changed my life!
I was down-and-out, living on the streets, barely scraping by- fast forward to ten minutes after I watched this video: I just purchased a new home and a mid-sized sedan!
I can't thank you enough!!!!
You’re sooo right. This procedure worked perfectly the first time I tried, unlike other channels that tell you to push and hold.
I read about five other FAQs and watched two videos and none of them worked. The press at the same time and keep doing it until it popped up works EVENTUALLY one time but by the time I got it work I had to look at the next step and lost it and couldnt' replicate.
This method was WAY MORE RELIABLE. Thank you.
I’m glad I was able to help. Thank you for the comment!
Thank you so much! I was able to do my older printer but this new one I could not figure out. It's amazing how many more pages you can print when you do this. Thank you again!
Thank YOU for the easiest, no BS, set of instructions I've found to accomplish this!
Thanks for the tip! Everything on the internet about resetting this printer's toner counter was wrong (said hold the two buttons for two seconds, which doesn't work), but thank goodness your video was *right*.
I found the same thing when I was searching and is why I made this video when I figured it out. Thanks for watching.
Thank you so much! Instructions online were not clear and your video worked for me. I don't have the higher end model like yours but rather the HL-L3230CDW and this worked perfectly.
Worked great. Have version 1.30 and my black cartridge was just showing low, not out.
Important step missing is how to get to the screen shown at 1:53.
For me... I opened cover and then at top of lcd screen was little white on black textbox that says "Cover is Open >". Had to click on that little black textbook to get to same same screen as 1:53.
After that I could follow your steps. Thanks OP!
Thank you. This printer was driving me nuts and your instructions worked perfectly!!!
OH MY WORD, THANK-YOU JESUS! after almost an hour, your video helped me solve my printer's issue! THANK-YOU SO MUCH!
Updated to the lastest firmware on my L3270CDW as of 1/20/24 (V1.35 MAIN, V1.14 SUB1) and this toner reset method works just fine.
Remember, there's also a battery on the toner drum chip that can go bad, as well as a mechanical switch that flips when the toner drum claims to be empty. Each of those can trigger the replace toner error.
Great job. All videos should be this straight forward. Thanks.
Just want to thank you. I had enough toner for hundreds of pages left in the printer, but after a system restore the toner showed as nearly empty. That would have been two hundred Euros to print a few pages. Brother ought to put this information with the printer.
Thank you so much for your help. I canceled the cartridge order. My black cartridge showed full to the top after I reset it. Great instructions, I played your video a couple of times and paused it as need it. I did try a couple times as the first time the screen arrows didn't work so it took me off the reset screen. We just have to be patient, follow the directions and try a couple times. Thank you again.
It really worked! The first time it didn't, but it was enough to close and reopen the cover and do the procedure again. Thank you very much
I've just tested and it still works, thanks a lot. ( firmware versions : main version 1.30 - sub1 version 1.13 ).
It did not work at the first try.. I had to repeat it several times and as described in the comments I had to close and reopen the lid until it worked.
The order of the buttons was back 1st then cancel, then release then back.
Thank you for watching.
The only vid to show how to do it correctly..thank you
Thank you so much! I tried absolutely everything before and couldn't get it to work until I found your video!
I’m glad it worked for you. Thank you for watching.
Thanks a bunch! I mistakenly installed the black cartridge into the wrong slot when changing 2 colors. The black cartridge thereafter was being read as empty, when in fact it was brand new. Multiple attempts to reset (just like you said) were unsuccessful. Your method worked perfectly on my MFC 8900 CDW.
Thanks for this it worked perfectly apart from one extra step - when I opened the cover a yellow bar on top of the screen indicated the cover was open and I had to tap on the car to get the same screen shown in your video. After that it was exactly as described in the video.
You're welcome! I’m glad it helped. Thanks for watching.
This video was helpful for me to understand how to reset the counter on my HL-L3270CDW toner cartridge.
I’m glad I was able to help. Thank you for watching.
Thanks a lot, it was a little bit complicated for me in getting the reset menu. Hopefully, following will be clear for others.
Toner reset menu :
1.Open printer cover
2.Keep screen on yellow page (cover is open)
3. press Back + x (no need to hold)
Release both, then immediate press back.
Then rest is shown in the video.
I’m glad it helped. Thanks for watching.
Thanks you both of you, it help me a lot.
Thanks, it worked. Just to add a comment, the screen must display the "Cover Is Open" message for the fix to work.
This procedure also worked to get my Brother MFC3770CDW to accept a compatible cartridge as genuine. Thanks!
Thanks! Saved me a lot of time and nerves thanks to this video!
thanks so much! The only video I could understand and worked as a charm!
I’m not kidding. Your video is soooo helpful. It saves my life. Thanks ❤️❤️❤️❤️❤️
I’m glad I could help. Thanks for watching!
Thanks a lot!!! This worked. The problem I was having is the new cartridges were not registering as new and the printer was saying to replace the cartridge.
This worked perfectly for me! I had even installed a new cartridge and was still getting the error.
Thank you!!! works very well (short and precise)
Thank you sir, you saved my life at work today!
You are very welcome. Glad I could help. Thank you for watching.
Thank you so much! I'm using this video the second time!
Worked and saved me some $$ Thank you!!
Worked for me! Brother HL-L8360cdw - Than you sir!
Works for Brother HL-L8260CDW ! Thank you !!
THANK YOU FROM HEART, I'VE BEEN LOOKING FOR SO LONG FOR THIS PROBLEM. I HAVE THIS PROBLEM WITH NEW CARTRIDGES, sometimes it gives the black another time the yellow, although i didn't print even 50 pages!!!
I heard about using a tape on one side of cartridge and so you can stop printer from counting the number of pages? I am a subscriber indeed, your way of explaining is very simple and clear. Best wishes.
Thank you in advance for your reply about the tape thing.
Friendly regards
This is a great tip. Thanks so much. My problem is that I have replaced a toner cartridge and the machine is stuck with an error message of No toner. Any suggestions. I have tried many of the suggestions found online but nothing is fixing this issue
Not sure about your error message. Thanks for watching.
I am having the same issue - did you manage to get it sorted?
@@rockergirl2489 i bought and replaced my generic print cartridge with branded print cartridges and this fixed the issue. I was able to isolate the issue down to a single generic print cartridge but replaced them all with branded to avoid any future hassles.
@@aaronpen21 thanks for that - the black one is the only one displaying empty and they are all generic cartridges. I will get the Brother black one and fingers crossed that will do it. Thanks for your help 😊🙏
Excellent explanation and thanks for showing the cleaning of the corona wire, although its literally RIGHT THERE, i probably would have missed it otherwise. Great to know you can save money on these cartridge's. I don't know that there is a way to do a reset on inkjet cartridges, thus i'm switching to laser.
Glad it helped. Thanks for watching.
Thank you. This work for me. Very helpful
You are a life save. Thanks much for the video.
Glad to help. Thanks for watching.
This is a great video for resetting the toner cartridges; very sorry it did not help me though. My L3270CDW is saying "NO TONER" and although I was able to reset all the cartridges (quite a few times) I just cannot get it to work. And the screen continually says "Cover open". Someone commented on this and said they hit the "car" to get rid of it???? Firmware 1.33/1.14.
Very very helpful. Thank you very much
Super! This video actually helped. The others are outdated.
I’m glad I was able to help.
Thank you!! I can confirm that this works to reset incorrect "Toner low" message on HL-L2395DW as well.
Thank you for watching.
Thank you, thank you! Really funny that all the info online about this is wrong. Totally saved me some serious waste since I had a ton of ink left.
Thank you! :) You saved my marriage!
Glad I could help. No charge for marriage counseling. 😀 Thank you for watching.
This is amazing !!!
Thank you, thank you, thank you. It worked as you described.
You're welcome!
AWESOME! This worked. Thank you!!!
Glad it helped!
PERFECT. Works EVERY time. Thank you so much!!!!
Glad it helped! Thanks for watching.
Thank you!! Wish I had foind your video sooner.
I did this today and it worked. Thank you!
I’m glad I was able to help. Thank you for watching!
THANK YOU SO MUCH, working here in 2023
Works perfect by my dcp l3550cdw. Thank you.
WORKS!
Thank you
Thank you!! it worked perfect
THANKS FOR THE REVIEW SHARING. COULD U HELP UNDERSTAND HOW MANY PAGES PRINTS POSSIBLE FROM ONE SET OF HIGH YIELD CARTRIDGES? THANKS
Thank you sir for this video.
Excellent video
MFC L2750 worked for me. Thanks.
Glad it helped! Thanks for watching!
I have also used this trick and it was working. However i wonder if Brother have updated the firmwere so it is not possible anymore??
Thanks for the information but it wouldn't work on my printer after I refilled the the cartridge how can I get it to work. Thank you
Great video thanks so much
Thanks brother. Good video
This was extremely helpful, thank you so much!
I’m glad I was able to help. I looked for days trying to find out how to reset it and stumbled onto the solution by trying a combination of what others were saying worked but didn’t.
@@theknoxvillepicker I feel your pain. You figured out what I could not. Thanks 😊
Well it did reset the view on the screen to full for all of the toners, but it still says I'm out of toner despite brand new aftermarket toner. Ugh.
Works great, thanks!
Thanks, it worked perfectly
Glad it helped. Thanks for watching.
Great this helped to get the paper of my daugther out !
So glad this helped out. Thank you for watching.
Thanks, this works for brother MFC L3770CDW as well
You are welcome. Thank you for watching!
Thanks for sharing bro, work
I go through these steps it says accepted but then doesnt reset any advice?
Good morning, I tried to carry out this process on my hll3240cdw, but when I try to enter reset mode, it stays blank, nothing appears, as if there was another command missing.
Would you know how to reset the cartridge on this machine?
amazing thank you. I got a new Magenta Toner that is supposed to be compatible but it's not recognizing it. this will get me thru while I work out how to get it to work.
Any ideas??
I’m not sure on that one. Good luck and thanks for watching.
What borther uses no chips? That's great. Does the 2400x600 dpi is true or marketing? How does it compare to Minolta?
Your my new hero.
Glad I could help. Thanks for watching.
Hola ! Tengo la impresora HL L3280CDW (es la misma que esta, pero el panel totalmente touch) y no me funciona 😢 conoce algún otro método o deberia funcionarme de igual manera ?
I followed the steps and reset my toners. However, it still indicates, "Open the top cover and then install toner cartridge." I would appreciate any suggestions.
you saved me today!
hi/ do you happen to have the code for Brother HL-L3280CDW ?
hey.. it did work for some time, but it now it stayed low, after replacing new (not original) toner. It pretends that tonercounter reset is accepted, but it stays at low value, tried with different drums too
Great film material. For me, the problem was a little different. I had a "no toner" error without color specification. I followed the procedure according to the movie without success. Later I reset the printer to the factory settings - without success. I still had a "no toner" error. I remembered that I had one magenta toner in stock (not original) - I put it in the printer and fixed error - printer works. The error has disappeared. My firmware 1.27. The toners were about 50% of the toner level. It happened after a few days of disconnecting the printer from the power supply. Maybe it will help someone.
stopped printing. saw that black was low. bought a new one $80 (wow) installed. slid the slider. still wouldn't print. i went through the process and reset the counter for ALL the cartridges. still NO TONER. any suggestions?
@@tucknersipserweinstocksips2799 clean up the chip and the chip reader. Most probably your problem is there. Rusted or dirty.
@@francinomusic where its chip located ?
進入【碳粉歸零】視頻：2分20秒，需要將【回頭鍵】，【取消鍵】同時按下。
其中；三次的時間，各有不同。第一次：2秒鐘。第二次：5秒鐘，第三次：隨意時間。
便可進入【碳粉歸零】設定。
Wow.. magic! Thank you
Ici, j'ai réinitialisé les 4 niveaux d'encre -ce qui apparait bien sur les graphes-, mais indique en sus : "l'encre de l'imprimante est peut-être épuisée"; Bref - ça ne marche pas pour moi :-(( Une idée ?
I've done this multiple times but my printer updated firmware and it no longer works. Any work around on the new update?
Thank you for your help, but in my printer, it did not work.
I've successfully completed this toner counter reset before. But recently Brother updated the printer firmware and now when I complete the process and the reset is 'accepted' the toner color bar remains empty and the printer will not print. Any suggestions on how to fix?
My understanding is if you update the firmware this will not work. I am not updating my firmware and it is still working for me. Sorry you are still having issues.
I have updated my 3770cdw for several times and this working like a charm.. did you hold the back+cancel button for long time or just instant? I tried the long push didn't work, but the instant tap back+cancel then the back do works
I had my auto update off, and it still will not reset now. Which version are you on? I have 1.21 I believe it said.
@@ridwan2706 You have to open the cover until it clicks
@@ridwan2706 your method is the one that actually worked for me. When I instantly pushed both back and cancel together and then the back button fairly quickly it worked. Thank you so much for your comment!!
I have the same issue here. But it amazes me that nobody blames the Brother printer for this stupid mess. Everyone just accepts it and tries to find a way to bypass it.
thank you, its perfect!!
This worked for me, but one question.... Once I really do have to replace the toner cartridge, will I need to reset the counter again? Or does the printer do this automatically when the cartridge is actually replaced?
It should reset itself with a new cartridge. The printer should recognize it is new. Thanks for watching.
thanks it worked
CAREFUL! After upgrading to the latest firmware (1.27), this method no longer works! It still lets you access the menu, but even after resetting the cartridge, it still tells you to replace the toner and refuses to print. I still haven't found a workaround and according to Brother and the Internet, it is not possible to downgrade the firmware back to its previous version. Very infuriating...
Sorry to hear that. I have not updated mine and this method still works for me. Thank you for the heads up on updating the firmware. Hope that will help others from not updating unless they understand the consequences.
Yeah i'm experiencing the same issue now. Did you find any work around?
I have 1.27 and the process worked for me. Took a bunch of tries to get into the reset menu, but eventually succeeded and was able to do a reset (I reset both BLK entries, just to be sure). Printing is restored!
I have the same issue. The whole thing seems a bit broken. It thinks my magenta cartridge is full despite significant printing, but my yellow is apparently empty and no amount of hitting reset is fixing it.
@@theknoxvillepicker I'm on 1.31 and it works fine
Perfect, It's works...
Gracias me funciono super bien 👍👍
thank you!
thanks for the video. I got the "No toner. open..." error. Following your instructions i reset all counters and was hoping that then the error was gone as all cartridges have been replaced. But printer still thinks i need to place toner. It wont even tell my wich one an dthe funny poart is when i go to the toner life menu item...it shows all cartridges as full...
replacing the battery behind the chip of each toner solved my issue.
Yes this worked. Thank You
Glad it helped. Thanks for watching!
Thanks for the tutorial. Just one thing. When I opened my cover, the cover open screen didn't look like yours. It had a cover open notice, but it also showed other printer information. I had to press the 'cover open' message after opening the cover and then I ended up with the same 'cover open' screen that you had. If you do not have the single message of 'cover open' on the screen, the button pressing reset won't work.
Good tip! Thanks for watching.