Hi Mr Washy, Not sure if it is necessary to replace the pump ??? I would imagine that pump and the PCB board are different problems, trying to get your thoughts on this one as I may be able to learn something new. Thanks in adance
There is no reason to replace pumps if the board is bad. If you suspect a bad pump, test it with ohm meter, or better yet, apply AC power to it with a test cord and see what happens. Check with Digikey for the chip, if needed. Many times all that's wrong is a bad solder joint and the component is still good. Resoldering fixes it without buying any parts.
Hi Thanks for the good explanation. After replaced the control board I have dc3 add door error comes up. Do you know what is the reason and how to disassemble the add wash door? It is locked it and can’t open it manually. If you made a video how to figure it out add door unlock and how to disassemble add door that much appreciate. I couldn’t find a video for disassemble the add door exactly same model. Other model easy to unlock the bolts and take it out. It’s difficult. Needs Helps bro.
Just replace the main control PCB or the inverter drive IC? The video accurately describes the fault and cure but I think your being too optimistic Replacing the main board is expensive and risky as there maybe other damage caused by that board failure. The second option is tricky even for an experienced electronics technician, replacing that inverter IC plus its surface mount resistors that will also have failed plus the additional problems of the silicon potting compound means a repair is very unlikely to be successful. Bottom line; this is unfortunately an expensive failure that would only be carried out as a warranty replacement of the main board, if the machine is outside of its guarantee, sadly it is not economical to repair
Hi I have washer dryer and doesn’t start any cycles..when I put any program also for dryer lock the door and after few seconds unlocked the door and stop any idea ?
Hi ,I have the same washing machine , I changed the spider shaft because it was making a noise, and now I have put it back together I have the same problem as yours. before I changed the shaft it was working all good,. Is there any way you can reset this washing machine to factory setting? ps your video is very helpful.
Mr washy, i got issue , my machine motor is running and stuck and sometime its run or 1 turn and stop and 3e error , what yoi think motor control board problem or motor?
Have a samsung WF45M5500AW/A5-00 front load. Control board needed replaced. Now that the new one is in, it no longer spins. But everything else now works, any suggestions
A great video. My Samsung is pumping water in, but the drum isn't rotating. I can hear it click and try and start moving. So first job, check motor is turning.
@@learn-live-grow Same! Then it gives me spinning dash lines on all four LCD numbers. Tempted to replace the motor/stator and position sensor but would hate to drop $200 if it doesn't fix it. Seems like a motor issue to me since it refused to move at all.
Never had a piece of technology this bad, never buying another product from Samsung ever again 🤣 can’t believe using a washboard is more effective, a wooden board invented in the late 1700s is better than a Samsung washing machine that’s half a grand 🤣
This is basically how I feel repaired it under warranty like 3 times now it doesn’t spin Fml never buying a Samsung again it’s bloody ridiculous…. My mum had a washing machine for 20 years about 5 years ago she replace it …..
Hello I have the same model I’ve changed main board and motor, the drum won’t rotate at all it tries to It’s like there’s a brake on , drum is not seased as it spins easily by hand, any advice
Im curious of the same and as the pump is a standard motor, not inverter I would have suspected that it runs off either one of the relays or fets towards the left hand side of the board.
Loom from the pumps runs back up the front of the washer and up towards the front control panel by the left side of the drum. Top connector on inverter board is power in with fuse in line of the top most pin, middle connector is motor output and bottom connector heads up the loom at the back of the washer back to the control panel. Tl dr; pumps don’t run off the inverter.
Because there is not surg protection. When the bubble pump faile they ends up charges the magnetic field when powered up then when the power cuts out the charged magnetic field gose back the way it come in straight to the pcb and good night
Hi! Thanks for a nice diy! I have this exact model and problem. I can’t find the PCB as a spare though. Do you know where to buy it or do you have a part number? Thanks!
Non inverter Ecobubble 9kgs. Pausing. Reseat all control board connections and good again for a while. did this 2 times already. today cleared a no drum turn with 3e error and last time persistent pausing. Quasi certain that board and motor are not at fault.
Hi ..can you make a video for the problem of the small door of the front load cant open / stay lock... Thank you and looking forward for considering my request ..God bless
hello, if you can help much thanks! samsung washer wf45k6200aw/a2 getting code 3c2 only when loaded down and wont spin. spins fine empty, i can get through diagnostic mode fine. replaced inverter but that didnt fix it. any suggestions?
Hi might be couple of things. Disconnect the recirculating pump wires (there’s two of them connected to the pump ) your washer has two pumps one for draining and other for recirculating water. The drain one is the one close to drain hose so disconnect the other one and start washer. If that doesn’t work could be faulty door switch. Failing that it’s the motor controller on your main board, it’s rarely the wiring to door switch
@@askmrwashywashy no error code, already change new door switch but still have same problem. after press the start button, then will have 3-4 time door lock sound repeated, normally only 1 time lock sound. then the drain motor sound, after that no water and not spinning.
@@williamchua4890 Same for me. I also get the circle of dash lines on the LCD screen. Drum will not rotate. Seems like a motor issue to me but haven't seen anyone share any solid resolution to their problems in the comments yet...
Good video, however, this is NOT an easy repair. Even if you can do this, pull out the main board and replace it, you're probably looking at a 200 dollar replacement cost for the main board. IMO, these computerized washing machines are inferior to the standard analog top loader machines. The machines with the LED lights below the control panel are for running diagnostic checks, referring to top loaders like GE, Maytag, etc. I can do without those LED computerized controls, since they are not as easy to diagnose. You really need a repair manual with explicit instructions to operate these systems, and washer manufacturers don't make it easy.
I have a WA50RS5400A series Flex washer upper washer is working fine but the bottom washer is not working properly Water is coming during rise and spinning cycle the direct drive motor rotates when Water comes in during rise time but the machine is not spinning water is draining it means the control board is faulty? not inverter? Please guide
? My washing machine motor turns over but will not spin I have it on the rinse spin cycle tickets to 9 minutes and just turns and stays on 9 minutes till the end of cycle then turns off with 9 minutes still on the display so what would cause this can you help me please before I go buying parts.
The motor control only controls the main drive motor in rear that was pointed out and the drain pump would have no effect on that board. The main board feeds the drain and recirc pumps and unless you are having drain problems not fixed by simply cleaning out the strainer they should be fine. I would ohm it out if concerned.
You. Can only order parts by model. Serial won't help. No parts store in the country can decipher a serial and figure out what machine it goes to. They need complete model numbers
![How to fix Shaky Samsung Spider Arm Washing Machine [FIXED] Imbalanced - Replacement, Flange Shaft](http://i.ytimg.com/vi/CNDuuHvrzPE/mqdefault.jpg)
![How to fix Shaky Samsung Spider Arm Washing Machine [FIXED] Imbalanced - Replacement, Flange Shaft](/img/tr.png)
how do you diagnose it and confirm whether it’s the board or the motor that is faulty??
Even I had the same question...
Hi Mr Washy, Not sure if it is necessary to replace the pump ??? I would imagine that pump and the PCB board are different problems, trying to get your thoughts on this one as I may be able to learn something new. Thanks in adance
I tried percussive maintenance and it worked
There is no reason to replace pumps if the board is bad. If you suspect a bad pump, test it with ohm meter, or better yet, apply AC power to it with a test cord and see what happens. Check with Digikey for the chip, if needed. Many times all that's wrong is a bad solder joint and the component is still good. Resoldering fixes it without buying any parts.
Hi
Thanks for the good explanation. After replaced the control board I have dc3 add door error comes up. Do you know what is the reason and how to disassemble the add wash door? It is locked it and can’t open it manually. If you made a video how to figure it out add door unlock and how to disassemble add door that much appreciate. I couldn’t find a video for disassemble the add door exactly same model. Other model easy to unlock the bolts and take it out. It’s difficult. Needs Helps bro.
Thanks man, great in-dept video. Every ot video is showing clogging and pump problems.
Hey there, i have the same issue. I can here clicking but it does not start spinning, i checked if motor is seized , but its spinning freely. Board?
Just replace the main control PCB or the inverter drive IC?
The video accurately describes the fault and cure but I think your being too optimistic
Replacing the main board is expensive and risky as there maybe other damage caused by that board failure.
The second option is tricky even for an experienced electronics technician, replacing that inverter IC plus its surface mount resistors that will also have failed plus the additional problems of the silicon potting compound means a repair is very unlikely to be successful.
Bottom line; this is unfortunately an expensive failure that would only be carried out as a warranty replacement of the main board, if the machine is outside of its guarantee, sadly it is not economical to repair
Does it have a balance sensor on the tub?
At the back I think
Hi Mr Washy, do you know how to do factory reset this samsung washing machine Model WW11K8412OW? tnanks for the answer.🙂
Very clear explaination . Thank you so much.
Hi I have washer dryer and doesn’t start any cycles..when I put any program also for dryer lock the door and after few seconds unlocked the door and stop any idea ?
There any Diagnostics mode to find error codes to determine exactly what the problem is with these washers?
Cheers.
Would love it if you shared the number off the "chip" it looks like an IGBT
Hi ,I have the same washing machine , I changed the spider shaft because it was making a noise, and now I have put it back together I have the same problem as yours. before I changed the shaft it was working all good,. Is there any way you can reset this washing machine to factory setting? ps your video is very helpful.
Diagnosis and how do you confirm ?
Mr washy, i got issue , my machine motor is running and stuck and sometime its run or 1 turn and stop and 3e error , what yoi think motor control board problem or motor?
Great Vídeo...
Thank you 🙂
Very helpfull video. But my machine is not spinning , can you tell me what to do ?
Have a samsung WF45M5500AW/A5-00 front load. Control board needed replaced. Now that the new one is in, it no longer spins. But everything else now works, any suggestions
Hi please check over your connections and make sure all was connected back properly
A great video.
My Samsung is pumping water in, but the drum isn't rotating. I can hear it click and try and start moving. So first job, check motor is turning.
Same issue. Got the fix?
@@learn-live-grow Same! Then it gives me spinning dash lines on all four LCD numbers. Tempted to replace the motor/stator and position sensor but would hate to drop $200 if it doesn't fix it. Seems like a motor issue to me since it refused to move at all.
Never had a piece of technology this bad, never buying another product from Samsung ever again 🤣 can’t believe using a washboard is more effective, a wooden board invented in the late 1700s is better than a Samsung washing machine that’s half a grand 🤣
This is basically how I feel repaired it under warranty like 3 times now it doesn’t spin Fml never buying a Samsung again it’s bloody ridiculous…. My mum had a washing machine for 20 years about 5 years ago she replace it …..
Hello I have the same model I’ve changed main board and motor, the drum won’t rotate at all it tries to
It’s like there’s a brake on , drum is not seased as it spins easily by hand, any advice
I have the very same problem, can you tell me how did you solve that???
Why would the pump be the cause of the failure? It isn't driven by the motor controller board going by the connections...
Im curious of the same and as the pump is a standard motor, not inverter I would have suspected that it runs off either one of the relays or fets towards the left hand side of the board.
Loom from the pumps runs back up the front of the washer and up towards the front control panel by the left side of the drum. Top connector on inverter board is power in with fuse in line of the top most pin, middle connector is motor output and bottom connector heads up the loom at the back of the washer back to the control panel. Tl dr; pumps don’t run off the inverter.
the pumps will not cause any failure on the drive motor pcb if the pumps are defective they can damage the main board
Because there is not surg protection.
When the bubble pump faile they ends up charges the magnetic field when powered up then when the power cuts out the charged magnetic field gose back the way it come in straight to the pcb and good night
How much time it run after changing the board?
What is the problem with this samsung eco bubble 6kg motor not running continuously
Hi! Thanks for a nice diy! I have this exact model and problem. I can’t find the PCB as a spare though. Do you know where to buy it or do you have a part number? Thanks!
Welcome. You’ll need to call Samsung or any authorised part distributor for the new part. If you remove your old one it will have the part number
Hi guys is there a factory reset on this model after replacing the drive motor now the washer is just stuck
Hi Did you replace the motor controller?
@@askmrwashywashy yes but now it doesn't even select program but if you put old motor controller you can select program
Non inverter Ecobubble 9kgs. Pausing. Reseat all control board connections and good again for a while. did this 2 times already. today cleared a no drum turn with 3e error and last time persistent pausing. Quasi certain that board and motor are not at fault.
Hi ..can you make a video for the problem of the small door of the front load cant open / stay lock...
Thank you and looking forward for considering my request ..God bless
hi I will try to get one done this weekend
Which one is faulty?
So exactly why did you leave the secondary pump disconnected?
It usually burns out the board unless you put a new one in
hello, if you can help much thanks! samsung washer wf45k6200aw/a2 getting code 3c2 only when loaded down and wont spin. spins fine empty, i can get through diagnostic mode fine. replaced inverter but that didnt fix it. any suggestions?
might be the sensor onto that detects drum movement.
My washer pause by it self and the drain motor start runing.
I replace mainboard and display board but its the same problem again. May i ask for tips?
Is there a leak somewhere? Usually that happens with flood protection switch at the bottom of the washer
Samsung WD85K5410OW this is the model of my washer. But i cant find the floodprotection switch you mean .
I followed this and bought the motherboard to replace but it didn't work or the problem is with the motor. Please give me some advice.
The motherboard at the bottom right ?
@@askmrwashywashy After changing the motherboard from the Samsung factory, it appears to work now. Thank you very much.
@@johmsmp welcome glad it works for ya
6:04 look into the machine at the bottom right :)
U didnt back the wire from pump
How to activate test mode, my friend
yes this
bu makinaya nasıl reset atılıyor sürekli analog makinalar gösterilmiş internette ama bu dijital olan model icin bir içerik yok
I have the same washing machine its not coming on what could be the problem?
hi could be main board problem
Panu po ung paglalaba at pag spin ko po my tumunog sa loob anu po ang sakit noon
At this point, I just bought a new machine
My motor controller is intergatred with controle panel...
hi my samsung WD80K6410OW/FQ
when press start the door lock sound tack tack tack, after that no water come in and spin, what is the problem, thx u
Hi might be couple of things. Disconnect the recirculating pump wires (there’s two of them connected to the pump ) your washer has two pumps one for draining and other for recirculating water. The drain one is the one close to drain hose so disconnect the other one and start washer. If that doesn’t work could be faulty door switch. Failing that it’s the motor controller on your main board, it’s rarely the wiring to door switch
Does it give an error code ?
@@askmrwashywashy no error code, already change new door switch but still have same problem.
after press the start button, then will have 3-4 time door lock sound repeated, normally only 1 time lock sound.
then the drain motor sound, after that no water and not spinning.
@@williamchua4890 disconnect the recirculating pump wires
@@williamchua4890 Same for me. I also get the circle of dash lines on the LCD screen. Drum will not rotate. Seems like a motor issue to me but haven't seen anyone share any solid resolution to their problems in the comments yet...
My machine is not get water into the washer
Good video, however, this is NOT an easy repair. Even if you can do this, pull out the main board and replace it, you're probably looking at a 200 dollar replacement cost for the main board. IMO, these computerized washing machines are inferior to the standard analog top loader machines. The machines with the LED lights below the control panel are for running diagnostic checks, referring to top loaders like GE, Maytag, etc. I can do without those LED computerized controls, since they are not as easy to diagnose. You really need a repair manual with explicit instructions to operate these systems, and washer manufacturers don't make it easy.
I have a WA50RS5400A series Flex washer upper washer is working fine but the bottom washer is not working properly Water is coming during rise and spinning cycle the direct drive motor rotates when Water comes in during rise time but the machine is not spinning water is draining it means the control board is faulty? not inverter? Please guide
? My washing machine motor turns over but will not spin I have it on the rinse spin cycle tickets to 9 minutes and just turns and stays on 9 minutes till the end of cycle then turns off with 9 minutes still on the display so what would cause this can you help me please before I go buying parts.
I have same prob and trust me non of them videos in youtube working to resolve it, i bet u have eco bubble one with no error comin up
@@soheil2626 I sure do mate no error codes days on 9 minutes just ends
@@soheil2626 did u ever fix it as I have same problem
Same problem here motor is free no codes showninf up an won’t spin
@@Paul-dc3pu no not yet still trying to work it out
New electronic...this repair everybody knows
hi my frind i need samsung front load pcb bord Please how can i gate this
Samsung or lookup on eBay
NEVER turn your washer on the dispenser side unless you want to break it.. this guy obviously hasn't been working on many of these
The motor control only controls the main drive motor in rear that was pointed out and the drain pump would have no effect on that board. The main board feeds the drain and recirc pumps and unless you are having drain problems not fixed by simply cleaning out the strainer they should be fine. I would ohm it out if concerned.
You. Can only order parts by model. Serial won't help. No parts store in the country can decipher a serial and figure out what machine it goes to. They need complete model numbers
I can tell washy washed out of his appliance repair job if he ever had one
bad fingers🤮