Thank you SOOOO Much!! You just saved me $200+ for a repair not to mention my time to wait for a repairman. Both of my handles were leaking, I followed your video and found that it was just the screws that hold the cartridge into place, tightened them up and no more leaks...Total repair time 7 minutes Total savings and gratitude to you, priceless!!! :)
I did follow this video and fixed our shower handle leak , it was exactly the same , so thank you for helping the plumber wanted $720.00 to fix leak , I bought those tools you showed and the assorted rubber washers at home depot for total of $52.00 Dollars !!!!!!!!
I have been complaining about water pouring out of the faucet handles for years and my landlord has not fixed. Going to do it myself now. Thanks so much for the video.
It all looks so easy on UA-cam. I never get ahead of the game on repairs. Will watch this again and again and see if I can do it. I am losing a lot of water with the dripping every day. Subscribed and hopefully I can do it.
Im glad you showed me the type of leak that happens when you turn on the shower. I believe I have a leak coming from the cold side and the middle now. I will be making a trip up Ace hardware tomorrow!! Thanks a million!!!
Thank you for clear precise instructions! My "new" old house is undergoing many repairs, but a leaky faucet was one problem I have never encountered. Problem fixed in just matter of minutes! THANK YOU again!!!!
Replaced my entire assembly. Both cold and hot were leaking. The hot one is fixed but cold still leaks. After watching this I now know to return the leaking one to Lowe's and get another one. Thanks for the video. Never knew that's where the water was coming from.
Single mom with two boys thank you so much the drip was getting heavier and heavier and it was the hot water, I have oil heat and septic tank needed to fix it before it became more expensive rubber washer was completely worn out
Hi does anyone know what size the washer is I have the same faucet but i don't know what size to get i bought a 3/8 however the hole is too small can someone please help me
Yeah this really helped me.. I was really having a challenge and was contemplating getting a Plummer.. that would cost me some much! But I did it myself. Thank you.!!!
Great video. Sometimes the valve will use an o-ring instead of packing. In that case, the valve will not show a packing nut but only the large hex fitting holding the stem. Remove the large hex fitting, unscrew the stem, replace the o-ring (lubricate it with silicone grease) and reassemble. The real problem comes if the valve is recessed inside the wall. In that case, use a deep socket valve wrench to remove the hex fitting.
Thank you so much for taking the time to post this video; it was exactly what I needed. I noticed that there are 106 dislikes. What's not to like! You show how a novice, like me, can save money and get the satisfaction knowing you did it yourself (with a little help). I guess it's true that you can't please all of the people all of the time lol. Keep up the good work. Sincerely. Tim
Some probably didn't like that he took apart the middle says you NEED to replace the packing (which he says may be hard to find), does NOT replace his packing, didn't even replace the beat up white washer....so all you really need to do is remove the stem, replace the easy to find end washer and reinstall. So people likely find it confusing that he show what he doesn't do but acts like you need to do it, but you obviously don't!
Really great video. Is it considered best practice to fill the faucet hole in the tile wall with plumbers putty, or alternately caulk around the top of the escutcheon, so the water dribbling down the wall doesn't make it's way into the faucet hole and into the inside of the wall?
Hi! Thank you so much for posting this video. The faucets, knob/handles, and even the wall tiles, are exactly identical to mine. My problem is as follows: I live in a rental basement apartment. My landlord gets very angry when there's any type of repair so I can't tell him about this I need to try to do this myself. The problem is I don't have access to the water main or even it's location. Is it possible to do this without shutting off the main water valve? If I tried, what would happen?
I'm so grateful with this guy and his channel in abril 2020 I had a very similar problem with my bathroom tube, cause the pandemia i didn't call the plumber I didn't want absolutely nobody in my home others than my family then I just watched this video and solve myself the problem plus I did save money, once again thank you very much for.
Very helpful tutorial video! I replaced a new stem, seat, and spring in the cold Valley faucet handle because the cold water leaking from the spout. I used a Danco part as Valley is out of business: 3Z-6H/C Stems assembly for Valley tub faucet. And yet it didn't fix the problem. Do you have any idea? Thank you.
Yes ,very helpful although I ran into another issue. Using the adjustable wrench to remove the piece, it would not come off , only spinning loose and could not see why. I could tighten back on but never completely removed. What's next? A hole in the wall behind the plumbing?
Any suggestions when the piece you need to originally use the wrench on is too far behind the wall to get any grip on it? I’ve tried a couple things but just cannot get any grip on it. Not even sure cutting the wall would allow me any more grip. Thank you for your help.
hopefully you still check near message boards but I have a very similar setup. but the difference is everything is behind the wall. meaning I can get the metal sleeves off but once I get to that first bolt you need a wrench for I can't get to it even with a socket wrench because of the rod coming out. is there a special tool I can use to get to that without breaking the tile
Marcus Free -- Yes, a ‘Shower Valve Socket Wrench’ (link below) will slide over the valve stem and fit the larger brass fitting much like a socket wrench. You can use the included Tee Handle or your adjustable wrench to loosen or tighten the valve stem nut. The link below also has a video allowing you to visualize how the socket works. Harbor freight has a killer price at only $11 or pay a little more at Lowes, Home Depot or Ace Hardware. While you have the valve stems out you should grab a flashlight and inspect the valve seat inside of the wall. A large leak over time will etch the brass seat and it will chew up a new stem washer in short order. If the valve seat needs replacing you will need a ‘Faucet Seat Wrench’ (link below). Lastly, as long as you have everything out of the wall, do yourself a big favor and REPLACE THE PACKING inside that valve stem and give yourself many, many years of leak-free service! These are NOT affiliate links, but will allow you to visualize the wrenches and how they work before you go to the store. You might ask the store if they have rental or loaner wrenches if money is tight Shower Valve Socket Wrench - fits 10 different sized stem nuts www.lowes.com/pd/BrassCraft-21-32-in-to-1-3-32-in-Shower-Valve-Socket-Wrench/999903493 www.harborfreight.com/shower-valve-socket-wrench-set-96322.html Faucet Seat Wrench www.lowes.com/pd/BrassCraft-Seat-Wrench/999903387
This is a great video. I am buying a house where the tub stopper doesn't work and the handles are leaking water. The shower diverter is also leaking. Will this same fix for the H/C handles work for the diverter? Thanks in advance!!
Thank you! My dripping shower had been driving me nuts and this was a great explanation of how to take the handle apart and identify a leak. My faucet looked slightly different but this explanation was good enough to guide me through
Hi I had my brother replace all the stems and so forth in my tub, it doesn't leak any more but it turns off and on differently, in other words it use to turn on if I turned it to the right, not I have to turn it to the left. How can I fix that? Thanks
Hi! Great video - is turning off the water from valve really necessary? I live in an apartment complex, they're not going to turn off water for me to fix this 😐
Thank you for putting this together and making it available. HUGE help!! And thanks for the heads up on size/faucet manufacturer for that washer - I would have assumed they were all a standard size but I'll take the piece in with me & make sure I get the right one. Probably saved me a trip or two. 👍👍
Hi, I have the hot water faucet which leaks hot water through the main drain. I have to purchase a shower faucet handle puller to get the hot water faucet handle off because it's corroded and won't come off by pulling it. My question is, how do you get the caulking off of the shower tile where the outer part that houses the stem is attached? I have caulking on all three handles attached to the tile on the wall. I just need to get the hot water stem out so I can replace the washer on the end of it. Is there an easy way to get the caulking off so I don't damage the tiles? Thank you, Kevin.
Can the problem be just the washer replaced second? And not the packing nut? Old taps may be hard to identify so wondering if replacing the laps may not be simpler?
after replacing diverter stem valve, shower head pressure was very low and I have to turn water diverter handle hard to get more pressure out of shower head.. How do I adjust so there's more water diverting to shower head? Should I put a new seat in even tho the old one works?
Good video overall, thank you. Only suggestion is once the valve stem is installed and prior to replacing all the trim pieces is turn the water on to inspect for any leaks that would not be visible once fully assembled.
Thank you for the video. After replacing, the handles are now harder to turn. Which pipe do I turn to loosen them up a bit to make easier to turn on/off?
As far as turning off the water. A plumber told me that when replacing washers on bathtubs be sure to turn your whole water supply off and not just for one side. Because of the way that bathtub pipes are connected you will get some water running out on you if you only turn off one side. I turn my water off from the water control in my yard.
@@gizzyguzzi - That’s what I’m thinking since it isn’t leaking when off. I’m about to give it a go. I am not a plumber but repaired a few valves over the years.
@@nja3224 well, I tell ya. I did two sets of these in a 50 year old house. They were leaking. What you have there is Price Pfister Verve faucets. All parts are readily available, online or HD. I would buy the rebuild kits Danco 24162, but you can buy the whole stem Danco 12H. If the knobs won't come off, buy the puller Husky #410-072-0111 . The socket to pull the stem out, Husky #16PL0135 , and behind the stem to remove and install the seat, Husky #17PL0305. New knobs are available too. I see this video does not replace the valve seat. I certainly would! It comes in the kit. Silly not to. Just do it all and get it over with. It's pretty easy. Worst part is old plumbing sometimes hard to get apart. The $20 in tools was well worth it. Still way cheaper than hiring someone or buy cheaply made crap they sell today!
@@gizzyguzzi - So I have it a go (still at it) and the cold water leak was fixed by tightening the packing nut about a quarter turn. Not as lucky with the hot water. I have the whole stem out now, the washer didn’t look too bad but I replaced it anyway. I’m assuming the seat is good because the washer wasn’t too bad but if I had a seat on hand I would have replaced it. I am now going to repack using graphite packing, just finished clearing out the old packing. I’m hopeful it will work, if not I’ll replace everything. Thanks for your reply. 👍
I haven't tried this yet but I feel much more comfortable after watching this. It didn't look like you replaced the packing though. Do you not have to?
Scott Johannessen It depends. The leak can also be caused by a worn out seat washer. Try replacing the seat washer first before you replace the packing. Inspect the packing. If the packing is worn or corroded it will need to be replaced.
Why not change the packing, too? You have the assembly out of the wall and why take a chance the the leak's not fixed. Plus I'd change the seats or the entire valve assembly.
I love DYI repair videos that clearly show you what to do and praise you for your time spend making this one. However, when an important step is left out, I feel compelled to add it to the comments section. Why in the world would you take the time to disassemble the valve stem packing assembly, pry out the obviously worn out, leaking packing and then put it back together and WITHOUT REPLACING the packing? This is grossly false economy and any future leakage at the seat will run right back out through the faulty packing into the handle again. Do the job right, do the job once. Do the job wrong, you’ll get to practice it again and again…. Also, while you have the valve stem assembly out you should grab a flashlight and inspect the brass Valve Seat inside the wall that the new washer will press against. Water leaking over time can etch grooves in the seat which will chew up new stem washers in no time and your leak will return. Replaceable valve seats cost a couple of bucks and a cheap ‘Faucet Seat Wrench makes replacing them easy. Non-replaceable valve seats can be conditioned with an inexpensive tool as well. When you are putting everything back together a $1 roll of Teflon tape on threaded surfaces will seal the connection and one roll of tape will last a homeowner a lifetime. ... Set yourself up for success with every repair you do. Valve stem washer, packing and Teflon tape should cost you around $5 to do BOTH hot and cold valves. Valve seats a couple of bucks each if needed. If the valves are back inside of the wall (as most are if tile is installed) and can't be reached with your adjustable wrench then a 'Shower Valve Socket Wrench Assortment' can be purchased at Harbor freight for $11 or at Home Depot or Lowes for $20. If the valve seats are bad the ‘Faucet Seat Wrench’ will set you back around $7. You can also ask your store if they have these tools available for rental or on a ‘Loaner” program. Always take the stems and worn parts to the store with you to assure that you buy the correct maintenance items. Close here doesn't count like in horseshoes. Once the store can identify the make/model of the fixture, many complete replacement valve stem assemblies can be purchased for as little as $8-$18 per side. A little more money, a lot less work and skill needed if you should so desire. If your local home improvement store doesn’t have the correct parts don’t despair. Google for ‘Plumbing Supply Store” near you. Even if they are a wholesale only shop, most of the counter personnel are more than happy to help you out if you’ve done your homework. They are also excellent at identifying the correct replacement parts for you and answering any questions you might have. Lastly, when you reinstall the valve stem assemblies make SURE the hot-water valve (red) is on the left side and the cold-water valve (blue) on the right. Install them backwards and your family will hate you forever or worse, someone could accidentally scald themselves and be injured (yes, it happens). Maintenance workers at apartment buildings are among the worst offenders for this rookie mistake - ask them to come back to your apartment and swap out the valve stem assemblies. Your life will improve immediately. lol I wish each of you the best of success in your DIY repairs!
Great video, but when I went to do this I discovered I had a cartridge-type faucet which just involved taking out the cartridges and replacing with new ones from Home Depot. Cost $25 but was slick. Could I even have rehabbed the old cartridges? And it sounded like there is no seat to replace, is that correct? I couldn't find one, anyway.
I thought the issue was the packing not the washer...I saw that you took out the packing and it looks like you put the same one back in. So in the end, was it the packing or the washer causing the handle to leak? Thanks
I have a question. is it possible to buy entirely new valves and replace them along with a new set of handles without having to replace the elements behind the wall? I have noticed most new faucet sets come with the pipe that joins the two handles behind the wall? Cant I just use new valves without replacing the piping behind the wall? Great video by the way. I'll be subscribing.
Yes. Whenever possible, replace the entire valve assembly, as you'll save a bunch of time with all-new parts. Plus he didn't replace the seats, which is the cause of many leaks. He got lucky.
Word of advise....When you turn the water off after the repair to check it, do not turn the handle so tight. Turn it just enough to make the water stop. You already are wearing a groove back into the washer when you turned it so tight. Otherwise, you covered almost everything nicely. Thanks.
I have been complaining about water pouring out of the faucet handles for years and my landlord has not fixed. Going to do it myself now. Thanks so much for the video.
Thank you...I was able to fix my leak : disassembled, picked up the new part from Home Depot, reassembled, done and in 20 minutes- including travel time.
Thank you SOOOO Much!! You just saved me $200+ for a repair not to mention my time to wait for a repairman. Both of my handles were leaking, I followed your video and found that it was just the screws that hold the cartridge into place, tightened them up and no more leaks...Total repair time 7 minutes Total savings and gratitude to you, priceless!!! :)
+Makaliiginger Glad to help. Can you please subscribe in return? I would really appreciate it. Thanks.
Stupid question. Do you have to shut the water off before you do this?
@@Ffoo_ffighteryes that’s an absolute must.
IT WORKED!!!!! Thank you so much for your teaching. Made me look like a super hero to my family.
God bless you!
I did follow this video and fixed our shower handle leak , it was exactly the same , so thank you for helping
the plumber wanted $720.00 to fix leak , I bought those tools you showed and the assorted rubber washers
at home depot for total of $52.00 Dollars !!!!!!!!
You're welcome. Glad to help. Can you please subscribe in return? I would really appreciate it. Thanks.
I have been complaining about water pouring out of the faucet handles for years and my landlord has not fixed. Going to do it myself now. Thanks so much for the video.
how did that work out for you?
The tip of my water valve stem broke when I was turning the knob, but this video helped me replace said water valve stem.
Thank you!! I replaced my washer for the hot water faucet today. Your video was so simple. I used to be afraid of plumbing, not anymore!!
You're welcome glad to help.
It all looks so easy on UA-cam. I never get ahead of the game on repairs. Will watch this again and again and see if I can do it. I am losing a lot of water with the dripping every day. Subscribed and hopefully I can do it.
Im glad you showed me the type of leak that happens when you turn on the shower. I believe I have a leak coming from the cold side and the middle now. I will be making a trip up Ace hardware tomorrow!! Thanks a million!!!
Very meticulous, gentle and easily understood. Despite the unclear audio. Thank you
Thank you for clear precise instructions! My "new" old house is undergoing many repairs, but a leaky faucet was one problem I have never encountered. Problem fixed in just matter of minutes! THANK YOU again!!!!
You're welcome. Glad to help. Can you please subscribe in return? I would really appreciate it. Thanks.
All DIY vids should be like this one...well done!
You're welcome. Please like, share and subscribe. I would deeply appreciate it.
Replaced my entire assembly. Both cold and hot were leaking. The hot one is fixed but cold still leaks. After watching this I now know to return the leaking one to Lowe's and get another one. Thanks for the video. Never knew that's where the water was coming from.
You're welcome. Thanks for your kind comment.
Single mom with two boys thank you so much the drip was getting heavier and heavier and it was the hot water, I have oil heat and septic tank needed to fix it before it became more expensive rubber washer was completely worn out
You're welcome glad to help.
Hi does anyone know what size the washer is I have the same faucet but i don't know what size to get i bought a 3/8 however the hole is too small can someone please help me
Yeah this really helped me.. I was really having a challenge and was contemplating getting a Plummer.. that would cost me some much! But I did it myself. Thank you.!!!
I’m getting ready to pop off my handles and work on a couple leaks, thank you for this video!
You're welcome. Please like, share and subscribe. I would deeply appreciate it
Great video. Sometimes the valve will use an o-ring instead of packing. In that case, the valve will not show a packing nut but only the large hex fitting holding the stem. Remove the large hex fitting, unscrew the stem, replace the o-ring (lubricate it with silicone grease) and reassemble. The real problem comes if the valve is recessed inside the wall. In that case, use a deep socket valve wrench to remove the hex fitting.
Bloom mlm
JFK yxu
Thank you so much for taking the time to post this video; it was exactly what I needed. I noticed that there are 106 dislikes. What's not to like! You show how a novice, like me, can save money and get the satisfaction knowing you did it yourself (with a little help). I guess it's true that you can't please all of the people all of the time lol. Keep up the good work. Sincerely. Tim
You're welcome. Glad to help. Can you please subscribe and like this video in return? I would really appreciate it. Thanks.
That is the first thing I did; GREAT JOB!
Some probably didn't like that he took apart the middle says you NEED to replace the packing (which he says may be hard to find), does NOT replace his packing, didn't even replace the beat up white washer....so all you really need to do is remove the stem, replace the easy to find end washer and reinstall. So people likely find it confusing that he show what he doesn't do but acts like you need to do it, but you obviously don't!
What if the knobs don’t come off
It's the plummer's dislikes 😂😂😂
Thank you so much for making this video. This is exactly what is happening to my bathtub Fawcett's.
You're welcome. Glad to help. Can you please subscribe in return? I would really appreciate it. Thanks.
No BS straight to the point very good video. Thanks.
You're welcome. Please like, share and subscribe. I would deeply appreciate it.
Thank you so much, the dripping was driving me nuts.
Really great video. Is it considered best practice to fill the faucet hole in the tile wall with plumbers putty, or alternately caulk around the top of the escutcheon, so the water dribbling down the wall doesn't make it's way into the faucet hole and into the inside of the wall?
Hi! Thank you so much for posting this video. The faucets, knob/handles, and even the wall tiles, are exactly identical to mine.
My problem is as follows: I live in a rental basement apartment. My landlord gets very angry when there's any type of repair so I can't tell him about this I need to try to do this myself. The problem is I don't have access to the water main or even it's location.
Is it possible to do this without shutting off the main water valve? If I tried, what would happen?
No. You must shut the water off prior to doing this job.
Hi your video are very clear and easy to understand. Would you be making a video how to fix a leaking diverter valve faucet leak?
Do you have two tighten that nut with the wrench ? I hand tighten mine would that cause the nut to become loose ?also sealer was apply
Ty so much saved a family some money. Bless up sir.
You're welcome. Please like, share and subscribe. I would deeply appreciate it.
A perfect video, he keeps it moving, professional
Glad to help. Please like, share and subscribe. I would deeply appreciate it.
Although the system in our house is a bit different from yours your video helped me a lot in ..... Germany!
I'm so grateful with this guy and his channel in abril 2020 I had a very similar problem with my bathroom tube, cause the pandemia i didn't call the plumber I didn't want absolutely nobody in my home others than my family then I just watched this video and solve myself the problem plus I did save money, once again thank you very much for.
You're welcome. Glad to help. If you haven't already please like, share and subscribe. I would really appreciate it. Thanks.
Very helpful tutorial video! I replaced a new stem, seat, and spring in the cold Valley faucet handle because the cold water leaking from the spout. I used a Danco part as Valley is out of business: 3Z-6H/C Stems assembly for Valley tub faucet. And yet it didn't fix the problem. Do you have any idea? Thank you.
This is exactly what I'm looking for. Thanks so much!
Alfredo Delgado You're welcome. Please return the favor by subscribing. Thank you.
Yes ,very helpful although I ran into another issue. Using the adjustable wrench to remove the piece, it would not come off , only spinning loose and could not see why. I could tighten back on but never completely removed. What's next? A hole in the wall behind the plumbing?
Any suggestions when the piece you need to originally use the wrench on is too far behind the wall to get any grip on it? I’ve tried a couple things but just cannot get any grip on it. Not even sure cutting the wall would allow me any more grip. Thank you for your help.
Do I need to shut off the main line in doing this?
Perfect video for a DIY'er like myself. Stopped my leak that I put off for too long.
Glad to help. Can you please subscribe in return? I would really appreciate it. Thanks.
hopefully you still check near message boards but I have a very similar setup. but the difference is everything is behind the wall. meaning I can get the metal sleeves off but once I get to that first bolt you need a wrench for I can't get to it even with a socket wrench because of the rod coming out. is there a special tool I can use to get to that without breaking the tile
Marcus Free -- Yes, a ‘Shower Valve Socket Wrench’ (link below) will slide over the valve stem and fit the larger brass fitting much like a socket wrench. You can use the included Tee Handle or your adjustable wrench to loosen or tighten the valve stem nut. The link below also has a video allowing you to visualize how the socket works. Harbor freight has a killer price at only $11 or pay a little more at Lowes, Home Depot or Ace Hardware.
While you have the valve stems out you should grab a flashlight and inspect the valve seat inside of the wall. A large leak over time will etch the brass seat and it will chew up a new stem washer in short order. If the valve seat needs replacing you will need a ‘Faucet Seat Wrench’ (link below). Lastly, as long as you have everything out of the wall, do yourself a big favor and REPLACE THE PACKING inside that valve stem and give yourself many, many years of leak-free service!
These are NOT affiliate links, but will allow you to visualize the wrenches and how they work before you go to the store. You might ask the store if they have rental or loaner wrenches if money is tight
Shower Valve Socket Wrench - fits 10 different sized stem nuts
www.lowes.com/pd/BrassCraft-21-32-in-to-1-3-32-in-Shower-Valve-Socket-Wrench/999903493
www.harborfreight.com/shower-valve-socket-wrench-set-96322.html
Faucet Seat Wrench
www.lowes.com/pd/BrassCraft-Seat-Wrench/999903387
Thank you so much…..you saved me so much time.working fine now.
You're welcome. Please like, share and subscribe. I would deeply appreciate it.
Very nicely done. Only thing i would add is recaulking around the cover.
Thank you for this man, it really was useful and helped me save a lot. Cheers.
You're welcome. Please like, share and subscribe. I would deeply appreciate it.
This is a great video. I am buying a house where the tub stopper doesn't work and the handles are leaking water. The shower diverter is also leaking. Will this same fix for the H/C handles work for the diverter? Thanks in advance!!
It should.
Thank you for this well-presented video. With this information, I was able to fix the problem.
You're welcome. Glad to help. If you haven't already please like, share and subscribe. I would really appreciate it. Thanks.
What ia the exact type of washer (sizes) needed for this model? Also this model of faucet.
I have the exact same one.
What faucet did u have what washer did u use
Thank you! My dripping shower had been driving me nuts and this was a great explanation of how to take the handle apart and identify a leak. My faucet looked slightly different but this explanation was good enough to guide me through
You're welcome. Glad to help. Can you please subscribe and like this video in return? I would really appreciate it. Thanks.
Hi I had my brother replace all the stems and so forth in my tub, it doesn't leak any more but it turns off and on differently, in other words it use to turn on if I turned it to the right, not I have to turn it to the left. How can I fix that? Thanks
Your videos are the most helpful I've seen. You make everything clear and easy to follow. Thank you again!
+Meisha Bendigo You're welcome. Can you please subscribe in return? Thanks.
Agreed, DIYU
I have the same thing happening along with a drip if I replace this and stop the leaking will it also stop the drip?
Hi! Great video - is turning off the water from valve really necessary? I live in an apartment complex, they're not going to turn off water for me to fix this 😐
Thank you for putting this together and making it available. HUGE help!! And thanks for the heads up on size/faucet manufacturer for that washer - I would have assumed they were all a standard size but I'll take the piece in with me & make sure I get the right one. Probably saved me a trip or two. 👍👍
Just like that I fixed my own pipe brother great tutorial...thank you!!
Thank you so much. Yea, I did it no more leaking faucet and I feel good.
You're welcome. Please like, share and subscribe. I would deeply appreciate it.
This valve mechanism is bad beast, too many task. Video is very informative
Glad t help. Please like, share and subscribe. I would deeply appreciate it.
I just replaced mine with your help, thanks
Hi, I have the hot water faucet which leaks hot water through the main drain. I have to purchase a shower faucet handle puller to get the hot water faucet handle off because it's corroded and won't come off by pulling it. My question is, how do you get the caulking off of the shower tile where the outer part that houses the stem is attached? I have caulking on all three handles attached to the tile on the wall. I just need to get the hot water stem out so I can replace the washer on the end of it. Is there an easy way to get the caulking off so I don't damage the tiles? Thank you, Kevin.
What model is the faucet in the video? I have the same model in my bathroom and need to buy parts for it.
Did you ever find the manufacturer? I've the same model too.
@@rdy4trvl Can't remember, sorry.
I have the same style of faucet. Where should I look at getting the replacement parts from?
Any plumbing supply store should carry them.
Can the problem be just the washer replaced second? And not the packing nut?
Old taps may be hard to identify so wondering if replacing the laps may not be simpler?
after replacing diverter stem valve, shower head pressure was very low and I have to turn water diverter handle hard to get more pressure out of shower head.. How do I adjust so there's more water diverting to shower head? Should I put a new seat in even tho the old one works?
Good video overall, thank you. Only suggestion is once the valve stem is installed and prior to replacing all the trim pieces is turn the water on to inspect for any leaks that would not be visible once fully assembled.
Thank you for helping me I highly appreciate it thank you again 🙂
Thank you
You make it look easy 🤷♀️
Wish me luck !!!
You're welcome. Glad to help. Can you please subscribe in return? I would really appreciate it. Thanks.
Thank you for the video. After replacing, the handles are now harder to turn. Which pipe do I turn to loosen them up a bit to make easier to turn on/off?
Thank you for the detailed instructions. More power to you!!
As far as turning off the water. A plumber told me that when replacing
washers on bathtubs be sure to turn your whole water supply off and not
just for one side. Because of the way that bathtub pipes are connected
you will get some water running out on you if you only turn off one
side. I turn my water off from the water control in my yard.
Should be able to tighten up the packing nut and call it a day.
@@gizzyguzzi - That’s what I’m thinking since it isn’t leaking when off. I’m about to give it a go. I am not a plumber but repaired a few valves over the years.
@@nja3224 well, I tell ya. I did two sets of these in a 50 year old house. They were leaking. What you have there is Price Pfister Verve faucets. All parts are readily available, online or HD. I would buy the rebuild kits Danco 24162, but you can buy the whole stem Danco 12H. If the knobs won't come off, buy the puller Husky #410-072-0111
. The socket to pull the stem out, Husky #16PL0135
, and behind the stem to remove and install the seat, Husky #17PL0305. New knobs are available too. I see this video does not replace the valve seat. I certainly would! It comes in the kit. Silly not to. Just do it all and get it over with. It's pretty easy. Worst part is old plumbing sometimes hard to get apart. The $20 in tools was well worth it. Still way cheaper than hiring someone or buy cheaply made crap they sell today!
@@gizzyguzzi - So I have it a go (still at it) and the cold water leak was fixed by tightening the packing nut about a quarter turn. Not as lucky with the hot water. I have the whole stem out now, the washer didn’t look too bad but I replaced it anyway. I’m assuming the seat is good because the washer wasn’t too bad but if I had a seat on hand I would have replaced it. I am now going to repack using graphite packing, just finished clearing out the old packing. I’m hopeful it will work, if not I’ll replace everything. Thanks for your reply. 👍
@@nja3224 if you have a HD around, the rebuild kit with correct packing and a new seat is under $4
What manufacture was this tub faucet set?
Thanks for the video, it helped me fix the shower faucets.
You're welcome. Glad to help. If you haven't already please subscribe to show your support. It would be deeply appreciated.
New subscriber!!! Now to get the guts up to do it!!
I got a quarter into your video and then stopped my leak. Thanks
Glad to help. Can you please subscribe in return? I would really appreciate it. Thanks.
Do you know the size and brand of that stem valve..1/2 or 3/4...
How do you get a handle off if you have a stripped screw? My screw is stripped. I've tried an extractor but it didn't work.
Thank you ima try this... wish me luck I just need to find the main water line
This was very helpful. Thank you!
You're welcome. Please like, share and subscribe. I would deeply appreciate it.
Great instructional video, short & simple, cheers!!
Glad to help. Can you please subscribe in return? I would really appreciate it. Thanks.
I haven't tried this yet but I feel much more comfortable after watching this. It didn't look like you replaced the packing though. Do you not have to?
Scott Johannessen It depends. The leak can also be caused by a worn out seat washer. Try replacing the seat washer first before you replace the packing. Inspect the packing. If the packing is worn or corroded it will need to be replaced.
***** the seat washer is the small one right?
by the way I subscribed to your channel great video
I❤BoXing3000 It's shown at 5:00. Thank you. I appreciate it and glad to help.
Why not change the packing, too? You have the assembly out of the wall and why take a chance the the leak's not fixed. Plus I'd change the seats or the entire valve assembly.
Very thorough! Thank you😊
You're welcome. Please like, share and subscribe. I would deeply appreciate it.
I love DYI repair videos that clearly show you what to do and praise you for your time spend making this one. However, when an important step is left out, I feel compelled to add it to the comments section.
Why in the world would you take the time to disassemble the valve stem packing assembly, pry out the obviously worn out, leaking packing and then put it back together and WITHOUT REPLACING the packing? This is grossly false economy and any future leakage at the seat will run right back out through the faulty packing into the handle again. Do the job right, do the job once. Do the job wrong, you’ll get to practice it again and again….
Also, while you have the valve stem assembly out you should grab a flashlight and inspect the brass Valve Seat inside the wall that the new washer will press against. Water leaking over time can etch grooves in the seat which will chew up new stem washers in no time and your leak will return. Replaceable valve seats cost a couple of bucks and a cheap ‘Faucet Seat Wrench makes replacing them easy. Non-replaceable valve seats can be conditioned with an inexpensive tool as well. When you are putting everything back together a $1 roll of Teflon tape on threaded surfaces will seal the connection and one roll of tape will last a homeowner a lifetime.
...
Set yourself up for success with every repair you do. Valve stem washer, packing and Teflon tape should cost you around $5 to do BOTH hot and cold valves. Valve seats a couple of bucks each if needed. If the valves are back inside of the wall (as most are if tile is installed) and can't be reached with your adjustable wrench then a 'Shower Valve Socket Wrench Assortment' can be purchased at Harbor freight for $11 or at Home Depot or Lowes for $20. If the valve seats are bad the ‘Faucet Seat Wrench’ will set you back around $7. You can also ask your store if they have these tools available for rental or on a ‘Loaner” program.
Always take the stems and worn parts to the store with you to assure that you buy the correct maintenance items. Close here doesn't count like in horseshoes. Once the store can identify the make/model of the fixture, many complete replacement valve stem assemblies can be purchased for as little as $8-$18 per side. A little more money, a lot less work and skill needed if you should so desire.
If your local home improvement store doesn’t have the correct parts don’t despair. Google for ‘Plumbing Supply Store” near you. Even if they are a wholesale only shop, most of the counter personnel are more than happy to help you out if you’ve done your homework. They are also excellent at identifying the correct replacement parts for you and answering any questions you might have.
Lastly, when you reinstall the valve stem assemblies make SURE the hot-water valve (red) is on the left side and the cold-water valve (blue) on the right. Install them backwards and your family will hate you forever or worse, someone could accidentally scald themselves and be injured (yes, it happens). Maintenance workers at apartment buildings are among the worst offenders for this rookie mistake - ask them to come back to your apartment and swap out the valve stem assemblies. Your life will improve immediately. lol
I wish each of you the best of success in your DIY repairs!
What if the screws are broken. What is the best tool to use?
Great video, but when I went to do this I discovered I had a cartridge-type faucet which just involved taking out the cartridges and replacing with new ones from Home Depot. Cost $25 but was slick. Could I even have rehabbed the old cartridges? And it sounded like there is no seat to replace, is that correct? I couldn't find one, anyway.
Hi. Si ce the packing was worn, why didn’t you replace it?
How can I remove the pipes over the stems? They won't unscrew
Please help
Thank you so much this video helped me out a lot
You're welcome. Glad to help. Can you please subscribe in return? I would really appreciate it. Thanks.
thanks man but I live in a condo and I not authorized to shutoff the main water system
Wow, nice. A dishonest plumber could have told me that the wall needed to be opened up, and I would have had no idea how simple this repair was.
Glad to help. Can you please subscribe in return? I would really appreciate it. Thanks.
Same here, a plumber told me I needed a $3,000.00 bathroom update.
Also if it leaks will water go bihind the wall
Do I need to do the same if water leaking from the faucet not from the handle?
See this video ua-cam.com/video/gOu2c2GvXR4/v-deo.html
Great vid. The screw has worn out and O could not remove it.
Glad to help. Please like, share and subscribe. I would deeply appreciate it.
Could the water be going back into the wall?
I noticed the squeaking sound went away, do you know how to fix only the squeaking sound?
good video sir, i like the way you show step by step thanks for the video..
+Jonathan Lopes Glad to help. Can you please subscribe in return? I would really appreciate it. Thanks.
I thought the issue was the packing not the washer...I saw that you took out the packing and it looks like you put the same one back in. So in the end, was it the packing or the washer causing the handle to leak? Thanks
MY parts are brand new and it is leaking ! What else could it be if it is not the packing.
Can you also just get a new valve?
Excellent video! 👍 Thank you
Nice, very helpful. Would have been nice to see the valve seat replaced too.
ua-cam.com/users/edit?o=U&video_id=4zhahwt0ZbQ
I have a question. is it possible to buy entirely new valves and replace them along with a new set of handles without having to replace the elements behind the wall? I have noticed most new faucet sets come with the pipe that joins the two handles behind the wall? Cant I just use new valves without replacing the piping behind the wall? Great video by the way. I'll be subscribing.
Yes. Whenever possible, replace the entire valve assembly, as you'll save a bunch of time with all-new parts. Plus he didn't replace the seats, which is the cause of many leaks. He got lucky.
Do you have to shut the water off before fixing?
Yes.
Great video thanks. Helps us all so that we can plan for having hopefully the least amount of downtime. :)
You're welcome. Glad to help. If you haven't already please like, share and subscribe. I would really appreciate it. Thanks.
Very good video and great instruction, very helpful, thanks.
You're welcome. Glad to help. Can you please subscribe in return? I would really appreciate it. Thanks.
Word of advise....When you turn the water off after the repair to check it, do not turn the handle so tight. Turn it just enough to make the water stop. You already are wearing a groove back into the washer when you turned it so tight. Otherwise, you covered almost everything nicely. Thanks.
I have been complaining about water pouring out of the faucet handles for years and my landlord has not fixed. Going to do it myself now. Thanks so much for the video.
You're welcome. Please like, share and subscribe. I would deeply appreciate it.
Thank you...I was able to fix my leak : disassembled, picked up the new part from Home Depot, reassembled, done and in 20 minutes- including travel time.
Glad to help. Can you please subscribe in return? I would really appreciate it. Thanks.