How To Install A Moen Shower Faucet - Step By Step - D.I.Y
Вставка
- Опубліковано 2 чер 2017
- This video shows how to install Moen Shower Faucet or how to replace Moen Shower Fauce step by step. It includes the shower arm the shower head and the shower Faucet. Ths shower faucet is Moen Banbury 82912SRN = amzn.to/34fp3q1
Moen Shower Faucet = amzn.to/3l2PCp6 or amzn.to/34fp3q1
Amazon Deals:
Try Amazon Prime 30 days for free = amzn.to/2JMWaLe
Create Amazon Business account = amzn.to/3mLSyYt
Joint Amazon Prime Watch Thousends Of Movies and TV = amzn.to/33NfsHD
Try Personal Shopper Wardrobe amzn.to/2VClfv9 - Навчання та стиль
Faucet used:
Moen Shower Faucet Banbury 82912SRN = amzn.to/3l2PCp6 or amzn.to/34fp3q1
Amazon Deals:
Try Amazon Prime 30 days for free = amzn.to/2JMWaLe
Create Amazon Business account = amzn.to/3mLSyYt
Joint Amazon Prime Watch Thousends Of Movies and TV = amzn.to/33NfsHD
Try Personal Shopper Wardrobe amzn.to/2VClfv9
N mm ok l kk❤npu7kllkn😊😊pl
Straight to the point. No BS. great! Thanks!
You are a lifesaver! I took this damn thing apart and I couldn’t figure out how to put it back together. Your video was spot on! Well done sir
Any time.
Everything looks good and the instructions I will highly recommend to drain the water into a bucket first before install showerhead so all the residues are in water line goes to bucket not to the new shower head filter… you will see yelllowish water and some small particles first ,then clear water will appear thank you
Thanks a lot for the info.
like most of your other comments here, I bought a brand new house with everything being installed reversed, your video was straight to the point and VERY helpful, after using my shower either extremely hot or extremely cold, tomorrow my family will bask on the ideal temperature they deserve. THANK YOU SIR!
Thank You
Very simple, very direct, very clear, very helpful. Thank you.
Thank You
My faucet handle was installed incorrectly. This video helped me fix it correctly. Thank you!
Thank You
Thanks! I’m trying to diagnose why our Moen faucet valve is sticking. This unit has almost identical components, and same tools to install/repair. This video goes into great detail.
You're welcome!
Thanks, had a stem go bad when some sand got into our water system this helped me remember the config for the handle. Also if you have hard water and you are replacing the stem I had to use CLR and scotch bright to clean inside valve body before the stem would fit in even with the included grease. Nice vid thanks again sir.
Thanks for the info.
Thanks, dude. I was missing just one screw. You figured it out for me!
Any time.
That was so simply explained. Thank you!
Thanks, the instruction pamphlet sucks. This was perfect.
It appears my valve body wasn't recessed in the wall far enough, I have a 1.5 inch gap between valve handle and escutcheon, now what any suggestions? Thanks great video
This gap is too much. Try long screws. If not you will have to install the valve properly.
Finally a video that helps. Thanks.
Thank You
Thanks for putting this video out. Instructions from Moen aren't the easiest to follow.
Exactly what I needed, thanks! I had lost my directions thank you one thing: you really have to tighten the adapter screw down hard -I was afraid I was gonna break the plastic but I kept going until it was tight.
You welcome.
Thanks
Any time
Thanks for the video, we did not know about the temperature control in are new faucet, in are new house and we had very little hot water.
Any time.
Good instructional video. Don't understand the negativity.
Me too. Thank You.
85 out of work plumbers dislike
Great video!!!
Thank you.
Any time.
Need to see how the valve is installed!!
Perfect!
Thank You
thank you :)
You welcome.
Nice job, thanks for share.
Any time.
Excellent!
Thank You
Great job
Thank You
thanks a load sir.😎
Do you need to caulk around that shower trim escutcheon so water doesn't get back in there or not necessary?
You can but it is not necessary.
Great video, but is this a replacement of what had been a Moen, so you could count on the mixer fitting the existing valve, or did you install a new valve before you began the handle installation?
I installed a new valve. This is a remodeling shower everything is new.. If you have a old Moen valve most likely you can install a new Moen shower faucet with no issue.
Thanks for the video. I am installing a similar Moen Alder 82603 shower faucet and have a question. As you know the trim ring has a red mark on the left side for hot, and a blue mark on the right side for cold. When I turn the handle to the left (it only turns in the left direction) cold water comes out, not hot. As I turn it down, around the 6:00 position the water starts getting warm as I would think it would, the further I turn right hotter the water gets as it would make sense until the knob stops turning around the 1:00 position. Is it correct that cold water comes out first not to get burned? And if it's correct cold water would come out first to the left, why would Moen mark the trim ring red for hot instead of blue for cold?
You installed it incorrect. The ring red is hot !! You did not install the knob correctly. Look at this video ua-cam.com/video/tqkC4bQ3FiQ/v-deo.html&ab_channel=JosephK start at 16 minutes.
gaps between knobs and wall bigger?
What part do you need to apply plumbers Grease too? Mine has been in 2 years and is making bad noises when turning the shower valve.
I believe you can put it before step one, You should use the plumber grease on the valve. The valve usually comes with grease on its surface.
@@josephk9182 thx
I just had my shower Moen boardwalk installed the handle is very loose, gap between faucet and base. looks like it is almost hanging there and goes almost all around
You did not install it properly or there is a defect in the product so you can return it.
Oh, I get it, so the valve is fully connected up in every ones wall.
🤣
Do you know whats the size of the hex screw?
No. You will need to call Moen customer support.
At time 2:38, do you inspect, or find the handle level firmly attached? Does it have any play, can be wiggled by 1 or 2 degrees left to right? If so, what can be done to fix it? Thanks!
I verified it that the handle is firmly attached. It can play 1 to 2 degrees. You should make sure that the level handle adapter is attached properly to the cartridge, make sure that with the Philip screw is tight. Also attach the Allen screw firmly to the level handle adapter.
@@josephk9182 I verified that the Philip screw attaching the Adapter to the cartridge that it was at first not too tight. Then I found a gasket washer that fits the hole and the screw to make sure the screw is tight. It was tight until when I use the handle to test it, then the handle lever, while not as loose as before, tighter, but still has some play. The Allen screw is tight, no wiggle backward or forward on the handle, still some play left and right.
Note that in my other bathroom, the original acrylic handle (knob) which is working, there is the same play of 1 or 2 degrees, so it may be normal???
@@TheDzungTa 1 to 2 degrees is perfectly okay
Had a plumber install the moen valve then months later I was able to tile the shower. Then I installed the moen shower faucet exactly as your video but no water comes out, what gives?? Water to the entire house is on. Any tips? Thanks!
Did the plumber test the valve ? Check your installation without shower head install. If it does not work remove the installtion and check the valve by moving the (hndle) knob to see if water coming from the shower otherwise you may have a defect Moen kit.
@@josephk9182 figured it out. The hot and cold valves were closed. He did not test the valve after install as I did not have the shower pan water sealed at the point of install. Once I turned the valves on and turned on the main the water came out. Huge relief. Thank your for replying!
@@CGphotoOp Happy for you.
Simple, straight forward video. Do you ever put any caulking or anything on the shower arm flange? Thank you.
You did not explain why leave the white plastic limit stop piece should be at 2 o'clock vs 12 o'clock position on the valve handle? Your video looks like at 1 o'clock position. What's the difference? Does this make it more hot or less hot at 2 o'clock position. Please advise before I do my install. Thank you for the great video!
It is the adjustable temperature
limit stopo'clock is hotter than 1 O'clock and 1 o'clock is hotter than 12 o'clock.
Great video! I am trying to install a Moen Alder 82603 which looks exactly like the one you have. I followed your installation and all looks good. However, when I turned it on, I am seeing just a minimal amount of water barely running from the tub sprout; nothing is coming from the shower. The water supply to the unit is very good. Do you know what may cause this? Do I need to do any adjustment on the unit before water start flowing?
The adjustment is for the water temperature not for the water flowing. Make sure the valve to the water pipe supply is opened all the way. Otherwise, it maybe a bed shower valve or a shower cartridge.
What size hex? I have a new home. I don’t have the original hex wrench
I believe 3 mm .If you have a hex set one will work.
7/64”
So to confirm, with this faucet I have to start with cold water first then hot? I thought my plumber had installed it incorrectly
When I initially turn it on?
Yes, the cold water is first. The knob starts from the cold water (blue) and move toward the hot water (red). It is against code to start from hot water. The plumber may install it incorrectly, verify that the plumber is licence.
Joseph K got it!! He is. Thanks so much for the reply. I thought it started at the middle. Also that head pressure is pretty strong this unit by moen does not allow me to turn it down
You can easily replace the head shower with another one that allows you to set the water pressure. It is sold in any home improvement shop.
Didnt show how to install the valve-body or diverter.
Thank you a dozen times….the instructions they provide suck! Thank yo
Any time.
Why didnt you use pipe thread or pipe dope for the pipe isnt teflon for plastic pipe
I used what the manufacture is recommending In my case Teflon was recommended for the shower head. I believe it is plastic that look like metal.
Joseph K Oh alright thanks for answering my question
oscar jojo
No. You can use it with any treating, except gas. They make a special Teflon for that.
Hats the stop tube. Come on man
You did the most important part of the video very quickly and you cannot see how you are doing the white pieces in the valve.🤔🧐
Sorry about it. The adjustable temperature limit stop should be pointed to 2 Oclock.
You show us the parts but then your hands covers up which part you're putting in first and what you're doing with it.
Yes I might needed to give more details however, I showed the right order of how to put the shower faucet parts. Please note, when you buy shower faucet it comes with instructions. The proper order may confused but the order is the same for most shower and what left you to do is assemble the parts using screws and washers comes with the faucet.
So incredibly helpful!! Step by step, plumbing for dummies, it got me through. Thank you Joseph K.
Any time.
I can’t hear you. Don’t be shy.
I ain’t heard nothing 🤭😂
Camera to far away.
Can't see what you are doing.
.
Sorry for that.
um, your practically finished... how about setting elevation of the posi temp valve...
disappointing video
To far from the wall
A closer look would've been better , thumbs down
You must be the paint by numbers type
Dave S I painted your mom’s “numbers.” Giggidy!
It's so far away from the camera I can't see what he is doing.
It helps me alot, especially my first time encounter to install such type of plumbing appliances...but, let me ask sir, in the cold connection side of the valve. It looks like, it's been blocked by some kind of rubber. How I should deal with it, should I live it as is???? Appreciate your reply sir....thank you...
There is an issue with your cold water valve or wrong instillation . Hard to say.
Thks. No small bead of silicone around shower etcheoun (spell? lol)
Not needed.