If you have a can with product but no pressure left, I have used my air compressor and a blow gun with a soft rubber tip to re-pressurize the can. Just remove spray tip, place rubber nozzle from blow gun over can valve tightly and give it a couple good bursts! You will feel it when you get it right its like blowing in a drinking straw. Then just put the nozzle back on and boom it should spray again! Don't over do this and you will need at least 60 psi or so to overcome the can valve but I have had great success with this! Keep in mind that liquids that cure in air like paint you should probably use quickly.
Great video, They should make those nozzle stem tips out of the same kind of plastic those clear packages for products at Costco are in, like SD Card packages that you practically have to use tin snips to open. The plastic that the spray can nozzle stems are made of is very brittle, I had the stem break off a can of carburetor cleaner bust and it only fell about a foot and a half and landed on the spray nozzle
I save Rustoleum spray can tips when the can runs out . I invert the cap , and put a drop of engine oil in the tip . When a Rustoleum can tip clogs , extras are available .
Places like Amazon also sell packs of brand new spray tips, I bought a variety pack with a dozen each of the most common spray tips, I been using a bunch of them to revive old spray cans
Thanks a bunch for the tips. I wish I had known about the Spray Foam Replacement Tubes before I threw out a perfectly good can that was three-quarters full.
Thank you so much man this was the exact same problem Im having right now with a broken tip. I actually had a nozzle for the phone the one you're talking about ordering through eBay and I didn't know what it was for and I literally just put it away about 5 minutes ago I'm not thinking it could give me a little bit of help but I can't wait to look through your other videos cuz I'm always working around the house looking for ways to save me a trip to the store
I was just getting ready to put a comment about safety glasses when you mentioned it at the very end. Thank you very much for that. A lot of UA-camrs have the bad habit of not using proper eye protection and actually present themselves as a bad example of safety practices. Thanks for your dedication to safety
@@AedanBlackheart are you naturally this hateful or do you have to practice? I'm happy I can provide a source of ridicule for you so that you can be nasty to somebody and make your day.
@@AedanBlackheart I am privileged to have provided you the opportunity to disperse your regular dose of hatred and belittlement toward people you have no knowledge of. Feel free to hate on me anytime you want. It does my heart good to know that while you're hating on me you can't hate on some other individual.
Great video I just ordered a nozzle for my full can of carburetor cleaner with broken nozzle cost me $10.00 if this save a can nozzle works it's a money saver I do buy a lot of carb cleaner.
Dude youre freaking awesome!!!! I have a few spare sprayers for my cans when they start acting up. And sugar i have 2 of those sprayer attachments. I have a condition called depuytens contracture and it affects me using aerosol cans. Thanks for the cool tips!
Save a Can apparently is no longer in business. Can't buy it anywhere. Please someone else pick this up & make it. We need something like this product.
Easier to decant and use in air brush or spray gun. The cost of “fix” not worth the cost for $6 can of paint. I can see this “fix” getting very messy when one slips up a little. All one has to do is press on the tip a bit too much and then………spray paint everywhere.
@@davidlong1786Either you are a very young man or you have NO children. I have never broken one either but my kids have “accidentally” dropped several cans resulting in exactly this thing happening. Take care~Linn
I have a hair spray that won't spray like it should. The tip is not clogged. I've even tried a brand new tip, and it still doesn't spray correctly. I've also tried pressing down on the tubing, and it comes out perfectly and at full force. I'm thinking that the tubing must be bent inside. What can I do to salvage this can of my favorite hairspray??
When I have a can that has lost its pressure, I make a slight hole at the top and depressure the can. Once the pressure is down, I enlarge the hole and pour the contents into a small glass jar. I have an airbrush, so if I need to spray paint the particular color I can use my compressor and the airbrush to use the product. Most of the times I did this for model painting and I got the best application of paint in comparison to the mist from the paint bomb can. Wd40 or other lubricants that are similarly affected, I just open the can and dump it into a jar and use a paint brush to apply to the surfaces that need treatment. I never waste a spray bomb can unless I have to do it.
For $12.99 I can save so much money on the dozens of $15-20 cans of paint I have that are broken. What about if you have a rustoleum universal brand of paint though? I have a few that have faulty sprayers and have no clue how to fix them or get the paint out of them safely.
I have an aerosol can of insect spray. It has the spray cap. And it has another cap that comes with a straw for crevice spray. I used the cap with the straw a couple of times. Now the cap with the straw doesn’t reattach to the can. The regular spray cap still reattaches no problem. I called the company. They sent me another cap with straw which still doesn’t reattach to the can. I’m confused why the spray cap still reattaches. But the cap with the straw does not.
The tips 13 bucks, plus shipping But it looks like its made in the USA out of brass, should last a lifetime If you can find it in your tool box. 1 can of whatever 2.99 To 12 bucks up to you if you bust a bunch of cans its worth it. If its just one can bummer.
I can’t buy this, the PayPal link doesn’t work. Suggests that the company is having issues. I don’t use Venmo and I am certainly never paying for anything by direct bank transfer. Available only on the company website apparently.
Um … it weighs a little less than 1/2 an ounce (4/10ths) This is pretty useful because a lot of these products are pricey and throwing the stuff away is aggravating.
Those trigger guns are awesome. I've been using them for years, and they make long projects like painting so much easier. That WD40 trick is very cool. I like those spray heads, and it never even occurred to me that they could be removed and put on other cans.
It’s early Sunday morning or Friday night at 11, you live 35 miles from a store, or maybe out at the ranch, you use a lot of these in your work, money actually matters and some of these products aren’t cheap, you just need to squeeze out a little bit more and don’t need a whole other can, and you’d prefer not to dump a bunch of chemicals in the trash. There’s a half dozen legit reasons not to just toss it in the trash and “go buy a new can”. Trolls.
There's alot of aerosol product out there that isn't just 3-4 dollars. I'd hate to throw a 15.00 can of paint away when I could have bought a reusable product that could save me that $$ then and in the future.
ITEMS I USED ON THIS VIDEO:
- SAVE-A-CAN Nozzle - saveacan.us/
- 7/64” Drill Bit - amzn.to/3Rf6Gv2
- Aerosol Can Trigger Gun - amzn.to/3sRXG5O
- Spray Foam Replacement Nozzles - amzn.to/46tJspu
- Wire Cutters - amzn.to/3QR0TKR
- Aerosol Spray Tip Red Straws - amzn.to/47u4ndk
- Compressed Air Aerosol Duster - amzn.to/3MVRznN
Save a can apakah dijual di Indonesia??
If you have a can with product but no pressure left, I have used my air compressor and a blow gun with a soft rubber tip to re-pressurize the can. Just remove spray tip, place rubber nozzle from blow gun over can valve tightly and give it a couple good bursts! You will feel it when you get it right its like blowing in a drinking straw. Then just put the nozzle back on and boom it should spray again! Don't over do this and you will need at least 60 psi or so to overcome the can valve but I have had great success with this! Keep in mind that liquids that cure in air like paint you should probably use quickly.
Mines broken down into the can.
Great video, They should make those nozzle stem tips out of the same kind of plastic those clear packages for products at Costco are in, like SD Card packages that you practically have to use tin snips to open. The plastic that the spray can nozzle stems are made of is very brittle, I had the stem break off a can of carburetor cleaner bust and it only fell about a foot and a half and landed on the spray nozzle
I save Rustoleum spray can tips when the can runs out . I invert the cap , and put a drop of engine oil in the tip . When a Rustoleum can tip clogs , extras are available .
Thank you for sharing my friend 🙏🏽😊
Places like Amazon also sell packs of brand new spray tips, I bought a variety pack with a dozen each of the most common spray tips, I been using a bunch of them to revive old spray cans
I think that weight is 4/10th of an ounce and not 4 ounces.
Thank you i was gunna comment this lol
Thanks a bunch for the tips. I wish I had known about the Spray Foam Replacement Tubes before I threw out a perfectly good can that was three-quarters full.
Great content. I have a few cans with broken stems, so I have some experimenting to do. 👍
Please let me know how it turns out 👍🏽😊
Thank you so much man this was the exact same problem Im having right now with a broken tip. I actually had a nozzle for the phone the one you're talking about ordering through eBay and I didn't know what it was for and I literally just put it away about 5 minutes ago I'm not thinking it could give me a little bit of help but I can't wait to look through your other videos cuz I'm always working around the house looking for ways to save me a trip to the store
This will work for cologne bottles also 👏👏
If you use acetone it will clean the spray foam out of the tip of the can and straw
Thank you for sharing! 🙏🏽👍🏽😊
I was just getting ready to put a comment about safety glasses when you mentioned it at the very end. Thank you very much for that. A lot of UA-camrs have the bad habit of not using proper eye protection and actually present themselves as a bad example of safety practices. Thanks for your dedication to safety
Mentions it within a minute and 5 secs, how short is your attention span? 😂
@@AedanBlackheart are you naturally this hateful or do you have to practice? I'm happy I can provide a source of ridicule for you so that you can be nasty to somebody and make your day.
@@AedanBlackheart are you naturally this hateful or do you have to practice?
@@AedanBlackheart I am privileged to have provided you the opportunity to disperse your regular dose of hatred and belittlement toward people you have no knowledge of. Feel free to hate on me anytime you want. It does my heart good to know that while you're hating on me you can't hate on some other individual.
@@mikeslater6246mike, did you see the laughing emoji, or did you miss that too. Everybody’s got hurt feelings these days.
Good video. I’ll have to try one of these on the varnish can I bought and lost the top sprayer.
Great video I just ordered a nozzle for my full can of carburetor cleaner with broken nozzle cost me $10.00 if this save a can nozzle works it's a money saver I do buy a lot of carb cleaner.
Como lo pidió y donde
I just received the save a can nozzle works great. @@guadalupemoreno7966
nice thorough explanation. But my new raid can doesn't spray to begin with and not sure if I'm supposed to take that slant tap off..
Dude youre freaking awesome!!!! I have a few spare sprayers for my cans when they start acting up. And sugar i have 2 of those sprayer attachments. I have a condition called depuytens contracture and it affects me using aerosol cans. Thanks for the cool tips!
Does the Save-A-Can nozzle come with different spray pattern for paint spraying?
Save a Can apparently is no longer in business. Can't buy it anywhere. Please someone else pick this up & make it. We need something like this product.
It is still in business. I just purchased one with the link he provided.
That can gun is my go-to friend for easy use on all my aerosol sprays.
At $18.99 for Sav A Can, there are not many cans worth saving.
It's meant to be reusable so it's an investment
Seriously, how many stems have you broken in your lifetime? I can say I've broken NONE. Yeah for $19 I can just go out and buy another can or 3.
Easier to decant and use in air brush or spray gun. The cost of “fix” not worth the cost for $6 can of paint. I can see this “fix” getting very messy when one slips up a little. All one has to do is press on the tip a bit too much and then………spray paint everywhere.
@@chevyDboyMike Just rem were you put it away for the next five years, the next time you need it. 😂
@@davidlong1786Either you are a very young man or you have NO children. I have never broken one either but my kids have “accidentally” dropped several cans resulting in exactly this thing happening. Take care~Linn
That's not 4 ounces, That's 0.4 of an ounce (4/10ths of an ounce).
great vid., i wanted to buy a Save A Can Tip but they only sell by 3 of them at the time almost 50 bucks! hell no.
This was an eye opener…thank you!😮
I’m glad I could be of help 👍🏽😊
Need help with rusty bolts I cannot unscrew from an outdoor flower box. Any tips or tricks…suggestions? Thanks
You have some really great and practical tips!!! Thank you!!! 🎉🎉🎉
Thanks for sharing.
You are very welcome my friend! 👍🏽😊
was hoping to find a tip on the Great Stuff thingy... my bran-new can fell and broke off the white tip at the steam :-(
Yes exactly the same problem face here
Thanks fr the tips. I'll remember this!!
You are very welcome! 👍🏽🙏🏽😊
I appreciate the video. I have several cans that I want to save
Acetone will clean the expanding spray foam from the nozzles.
Interesting tips, thanks.
Spray cans suck in general. I'm sure manufactures could fix the issues. The straws get lost or are the wrong diameter. 🙁
4:20. Weights is less than half an ounce. Missed the decimal. Thanks for highlighting the product though.
What if you don't have that tip?
The tip weighs point four ounces NOT 4 ounces ! Good video Thank you !
Thank you. I love the tips.
Where did you get it. I cannot find it online.
I did that today ❤. Thx
deoxit, freeall, some other suppllies like paint cans @$12/can @ HD, also deletes that irratating intagrated straw that wastes alot.
Keep up the excellent work and i wish you a million sub.
Thank you so much for the love and support my friend! 🙏🏽👍🏽😊
I have a hair spray that won't spray like it should. The tip is not clogged. I've even tried a brand new tip, and it still doesn't spray correctly. I've also tried pressing down on the tubing, and it comes out perfectly and at full force. I'm thinking that the tubing must be bent inside. What can I do to salvage this can of my favorite hairspray??
Thank you so much. So many awesome tips in one video. You just save me a can of sweet smelling Hawaiian spray. 😊
I’m glad I could be of help! 👍🏽🙏🏽😊
When I have a can that has lost its pressure, I make a slight hole at the top and depressure the can. Once the pressure is down, I enlarge the hole and pour the contents into a small glass jar. I have an airbrush, so if I need to spray paint the particular color I can use my compressor and the airbrush to use the product. Most of the times I did this for model painting and I got the best application of paint in comparison to the mist from the paint bomb can. Wd40 or other lubricants that are similarly affected, I just open the can and dump it into a jar and use a paint brush to apply to the surfaces that need treatment. I never waste a spray bomb can unless I have to do it.
Great idea, that's what I do with brake cleaner and carburetor cleaner and put in a jar to use for brush cleaner when the spouts break off the cans .
You can also pump air into the can!
For $12.99 I can save so much money on the dozens of $15-20 cans of paint I have that are broken. What about if you have a rustoleum universal brand of paint though? I have a few that have faulty sprayers and have no clue how to fix them or get the paint out of them safely.
I need it for canned air
4 oz. of brass is about the size of a golf ball.😅 Thanks though.. I'll have to get one.😉
Hehe 🙃
I just decant the paint and use a small touchup sprayer.
tip is about 4/10ths of an ounce eagle
Can gun is an amazing product! Cheap also - Walmart!
Yahoo! This can save about 60 bucks!
Good idea thank you
You are supposed to file the tip flat or cut it clean and even with a razor blade
Thankyou a lot it’s help Thankyou
I have an aerosol can of insect spray. It has the spray cap. And it has another cap that comes with a straw for crevice spray.
I used the cap with the straw a couple of times. Now the cap with the straw doesn’t reattach to the can.
The regular spray cap still reattaches no problem.
I called the company. They sent me another cap with straw which still doesn’t reattach to the can.
I’m confused why the spray cap still reattaches. But the cap with the straw does not.
THANKS SO MUCH HAVE A GOOD DAY
The tips 13 bucks, plus shipping
But it looks like its made in the USA out of brass, should last a lifetime
If you can find it in your tool box.
1 can of whatever 2.99
To 12 bucks up to you if you bust a bunch of cans its worth it.
If its just one can bummer.
I just tossed a new can of gap filler because the spray nozzle snapped off.
Thanks for the tips! :) Seriously, but I'll intend the pun for fun.
I think you maybe the best subscribe I happen to find due to one of your UA-camr friends. I can remember which one though.
Thank you so much for your love and support! 🙏🏽😊
I always invert the can when I'm done until no more product comes out to prevent there being anything to clog the nozzle.
Great hack!
Apakah dijual di Indonesia??
I clicked on the link provided and it took me to a dangerous website blocked page . what now?
😮
4:18 No way Jose...This is called decimal of what you said or Zero-Point-4 Oz!
hilarious that i ended up here after bringing home two full but broken o'reilly brake cleaner cans from work lol
I can’t buy this, the PayPal link doesn’t work. Suggests that the company is having issues. I don’t use Venmo and I am certainly never paying for anything by direct bank transfer. Available only on the company website apparently.
Thank U sooooo much
This not dangerous load?
I think that on those occasions it is better to take the paint out of the container and use it with an air gun.
Um … it weighs a little less than 1/2 an ounce (4/10ths)
This is pretty useful because a lot of these products are pricey and throwing the stuff away is aggravating.
sweet!
What’s with the glove fingers not all the way in!! 🤔
Broken tip should be cut level 90 degree.
Then the tip will screw in solidly no mess.
Those trigger guns are awesome. I've been using them for years, and they make long projects like painting so much easier.
That WD40 trick is very cool. I like those spray heads, and it never even occurred to me that they could be removed and put on other cans.
Heh... the spray valve is so-so but the great stuff thingies are a must :-)
Cool 😎 !
Shoee..doggy!
And of course, I just threw out a brand new busted spray can a few days ago .
I call that stem fixer a bs. Just get another can. Or just drill it and decan the paint.
thats alot of work
WOW
🤑Over $18 with tax and shipping. Save a can of cash instead!
I think the save a can company is out of business..... No response from this company anymore...
說話太多😢你做好我們就已經明白了🎉
👍👍👍👍👍
Thank you so much! 👍🏽🙏🏽😊
No thanks
Thats 0.4 Ounces lol
You used on different product bro .. don't b,s !!
you can buy a new can for less than $13 for this nozzle adapter.
How about long term? What if you have multiple broken cans in the span of many years?
So crappy 2:02
BS it doesn't work
Don't waste your time and $....just buy a new can of whatever.
🥺
Throwing out a perfectly good can of whatever is a waste of money.
It’s early Sunday morning or Friday night at 11, you live 35 miles from a store, or maybe out at the ranch, you use a lot of these in your work, money actually matters and some of these products aren’t cheap, you just need to squeeze out a little bit more and don’t need a whole other can, and you’d prefer not to dump a bunch of chemicals in the trash.
There’s a half dozen legit reasons not to just toss it in the trash and “go buy a new can”.
Trolls.
There's alot of aerosol product out there that isn't just 3-4 dollars. I'd hate to throw a 15.00 can of paint away when I could have bought a reusable product that could save me that $$ then and in the future.
Couldn’t find a bigger angle grinder?!? 🤣🤣 3:32
HOW TO GET IN CANADA, I ASKED IF SHIP TO CANADA. NO ONE BOTHERED TO EVEN ANSWER ME, and I KNOW they READ MY MESSAGE
Four ounces. 🙈
🤝