Dji Mavic Mini 2 Disassembly
Вставка
- Опубліковано 30 тра 2021
- Dji Mavic Mini 2 Disassembly
#djidrones
#djimavic2pro
#mavic3pro
#djimavic3cine
#djimavic3review
#djidrones
#mavic3cine
#mavic3review
#djimavic3pro
#djienterprise
#drone
#djimavicmini
#djimatrice300
#djimavicmini2
#djimavic3footage
#mavic3drone
#djim300
#djim30
#djiair2s
#djimavicair2
#mavic3footage
#djiair2s
#djimini3
#djimavic3cinematic
#djimatrice
#djimini2disassembly
#djimini2teardown
#djimini2repair
#m300
#djimavic3teardown
#matrice300
#djim30t
#djidrone
#mavic3
#djimavic3
#matrice300rtk
#djimini2
#djimini2gimbalrepair
#dronedjiinspire2
#dronedjimavic3
#djimini2controller
#mavicairdisassembly
Best mini 2 teardown video.
Cheers bro. Used it to disassemble and reassemble the drone
Reminds me of the class I took in biology where the teacher dissected a frog
Thx dude i appreciate the help 👍
Really great
Great
Sir, what is the black tape that was removed after you took apart. it is glued to each side of chassie. i can't find it in the repair kit as you dissembled it you took it out
I have a bit of a similar question to @relaxvideo3d where the best place would be to tap for a power source (any voltage between3.3v-17v) that was on only when the drone was on for a remote id module.
I want to paint my shell. It's the SE. I decided to use precise masking tape
Painted the blades, looks wayyyyy cooler.
Hi, is it possible to get 5V 1A from inside to a very specific outside camera? If possible, where exactly? Better open the battery maybe? thanks
Very nicely filmed. I am looking to remove the arms and motor from my mini 2se and sending the shell up to 100K feet in a high altitude balloon. Will the unit still take commands and send images?
I know its range is not that far, but even after it is out of range, will it continue to record video on the sd card? Thanks!
Hi What screwdrivers did you use
My Drone fell to the ground because of the tree branches and the upper and lower outer casing was broken. What is the best way to install a new casing? Can I install it on my own or do I need a maintenance technician?
You can do the bottom and top case assembly by watching my videos.
what is the golden foil sticker for in top shell?
They are for either directing the gps signal to the sensor, or to block any EMF/RF from entering or leaving sensitive comopnents.
very helpful video, thanks a lot))
hello, how do I get rid of the glue/silicon highlighted in 0:44?
I've seen in another video where they used a high-temperature heat gun that had a very small nozzle.
You've probably already done your repair, but in my case I had to resort to carefully and briefly holding the solder iron to it. You don't have to actually melt away the glue, but just heat it until it's pliable then it pops off. A small-nozzle directional heat gun is ideal, but I only have a large one that looks like a hairdryer. Which I'm sure would totally warp the frame and so on.
Thank you for your reply! I did exactly the same thing as you 😊
Hi. What kind of blue thermal paste is that under the heat sink. Can I change it to pc thermal paste?
You can replace it with the paste used in computer processors.
@@DjiTeknikServis thanks for the swift reply.
what is screwdriver size required to open mini2 body
The screw driver comes with the drone
Please help
Sir my mini2 drone gets disconnected from rc within 2 minutes of turning on drone without any flight
You probably need to update the drone via the dji fly app
I have the same problem now
Did u get the solution ?