Hello and thanks for the video. I have a lot of hot and cold water leaking out of the tub spout when I’m running the shower. I replaced the diverted valve and seat and there’s no difference. Any advice or things to look out for?
Thank you for the DIY vedio. I sm unable to take out the cattidge it is hard to twist. Can i use a hsmmer to force it to turn? Will i create a bigger problem? Thank you.
Thank you, just fixed a leaking bath faucet, I did use the teflon tape and the plumbers grease. I think the plumbers grease was helpful, not sure about the tape.
Important question: so my hot water and diverter taps ARE MISSING the part where the seat/bib is supposed to thread INTO. What am I supposed to do??? Replace/convert entire system? I can not use new stems even with new bibs because the bibs will not seat properly it’s all loose with nothing to thread to. Any info will help
Hello. This looks pretty identical to my 3 handle assy. By chance do you know of a kit that mostly just includes the stems (with or w/o the tools) for this set up. I don't need any new handles. Thanks much.
The stems can be purchased separately, but they tend to run around $25 each. Maybe purchase a kit like this and keep the handles for spares?? amzn.to/3vPDVe7
So I changed my hot and cold valve stems with good success. But when I changed my converter stem, now it won’t change from tub to shower. I have no idea what I did wrong here.
I replaced my diverter valve and now it doesn’t send water to my shower head. Can it that when I took out my old valve the washer was broken, could the broken piece got stuck where the water goes to my shower head. Cause now it just drips water from my shower head. Thank you 🙏🏽
Yes, that is probably what happened. Something similar happened to me once on a hot water valve. On that one, it wouldn't turn on. A small screwdriver or spring hook should be able to fish it out.
Where can I buy the washers….wont stop running…paid a plumber $1,000 to come replace stop my bathroom from leaking…1 year later leaking again..I just need to replace the rubber washer I believe
@michaelcapps8877 they can be purchased from any hardware store and are cheap. The rubber ones don't last very long. They sometimes carry another type that are nylon or maybe silicone that lasts longer. Take the stem with you to the store so you can match it up.
I have one just like this (only two handles, hot and cold) and when I tried to remove the cartridges because they are leaking, only part of the cartridge came out. Any tips on what to do other than calling a plumber? I replaced them once before and this time they don't want to budge.
My best guess is that you removed the piece of the valve. There are two nuts in there and the one further back is the one that you need to remove. The other option is that the rubber washer unscrewed itself and stayed in there. Needle nose piers should be able to get that out.
I used what I had already ( screwdriver, channel lock wrench, and pliers). Now That you have taught me easier to use tools. I plan to buy those if I can find them. I also knew nothing about the seat in the back. This might be why my husband replaced the valve a few times before he passed away and why I am doing the same now. I am going to wait until tomorrow to replace this and go to the store fir the seat and wrenches I need to put it back together correctly. Again thank you very much
This little ua-cam.com/users/postUgkxVoi3B4CB6Oygq1-vo4OTL1M_M5JkrXif tub works perfect in our 6 x 6 shower and is easy to get in and out. Also easy to drain.
Thanks, really helpful. I replaced mine with lever handles so thanks for explaining how they work opposite. Never would have known.
You're welcome! Thanks for watching.
Like. I am a 68 yr old widow
This will help me fix my faucet that was completely running and would not stop
Thank you
I am glad the video helped you, so sorry for your loss.
Hello and thanks for the video. I have a lot of hot and cold water leaking out of the tub spout when I’m running the shower. I replaced the diverted valve and seat and there’s no difference. Any advice or things to look out for?
Thank you! Literally helped me so much!
I am very glad to have helped! Thank you for watching.
Great, now I can replace my own. Thanks
You're welcome, thank you for watching!
Even found the tool to remove seat at out local true value.
Thank you for the DIY vedio. I sm unable to take out the cattidge it is hard to twist. Can i use a hsmmer to force it to turn? Will i create a bigger problem?
Thank you.
Thank you, just fixed a leaking bath faucet, I did use the teflon tape and the plumbers grease. I think the plumbers grease was helpful, not sure about the tape.
Thank you for watching!
Important question: so my hot water and diverter taps ARE MISSING the part where the seat/bib is supposed to thread INTO. What am I supposed to do??? Replace/convert entire system? I can not use new stems even with new bibs because the bibs will not seat properly it’s all loose with nothing to thread to. Any info will help
Tip: remove all the stems at once so they are not in the way of your seat wrench!
Great tip!
Or use the long end.
Hello. This looks pretty identical to my 3 handle assy. By chance do you know of a kit that mostly just includes the stems (with or w/o the tools) for this set up. I don't need any new handles. Thanks much.
The stems can be purchased separately, but they tend to run around $25 each. Maybe purchase a kit like this and keep the handles for spares??
amzn.to/3vPDVe7
So I changed my hot and cold valve stems with good success. But when I changed my converter stem, now it won’t change from tub to shower. I have no idea what I did wrong here.
Thanks
You're welcome!
What should I do if my nuts are partially in the mortar of the wall? Would a socket still work
The socket should still be able to get it out. If not, you may have to carefully chisel the mortar out from around it.
I replaced my diverter valve and now it doesn’t send water to my shower head. Can it that when I took out my old valve the washer was broken, could the broken piece got stuck where the water goes to my shower head. Cause now it just drips water from my shower head. Thank you 🙏🏽
Yes, that is probably what happened. Something similar happened to me once on a hot water valve. On that one, it wouldn't turn on. A small screwdriver or spring hook should be able to fish it out.
very helpful.
I'm glad that it helped. Thanks for watching!
Thankyou
You're welcome, thank you for watching!
Does the Shower Valve Socket Wrench Set work on the Rohl thermostatic cartridge ????
Where can I buy the washers….wont stop running…paid a plumber $1,000 to come replace stop my bathroom from leaking…1 year later leaking again..I just need to replace the rubber washer I believe
@michaelcapps8877 they can be purchased from any hardware store and are cheap. The rubber ones don't last very long. They sometimes carry another type that are nylon or maybe silicone that lasts longer. Take the stem with you to the store so you can match it up.
Hi, is it possible to do this without shutting off the water?
No, the water would need to be shut off.
I have one just like this (only two handles, hot and cold) and when I tried to remove the cartridges because they are leaking, only part of the cartridge came out. Any tips on what to do other than calling a plumber?
I replaced them once before and this time they don't want to budge.
My best guess is that you removed the piece of the valve. There are two nuts in there and the one further back is the one that you need to remove. The other option is that the rubber washer unscrewed itself and stayed in there. Needle nose piers should be able to get that out.
Hi. May I know the name of the tool you used to remove the stem? Thanks.
Here you go.
Faucet Wrench Set:
amzn.to/2VgSPqH
Valve Seat Wrench:
amzn.to/2B6SSyu
I used what I had already ( screwdriver, channel lock wrench, and pliers). Now That you have taught me easier to use tools. I plan to buy those if I can find them. I also knew nothing about the seat in the back. This might be why my husband replaced the valve a few times before he passed away and why I am doing the same now. I am going to wait until tomorrow to replace this and go to the store fir the seat and wrenches I need to put it back together correctly. Again thank you very much
Is the stem a standard size.
The thread size is a standard size by brand of fixture. The length varies by brand and type of handle used.
This little ua-cam.com/users/postUgkxVoi3B4CB6Oygq1-vo4OTL1M_M5JkrXif tub works perfect in our 6 x 6 shower and is easy to get in and out. Also easy to drain.
is there a reason why you wouldn't use plumbers tape?
Great question, I hit the Google and found this article about it.
www.thespruce.com/how-to-use-teflon-tape-2718712