XPEL used in this video: XPEL Paint Protection Film - amzn.to/3LjPaiW VViViD Premium Utility Blade (my favorite): amzn.to/39TIUP3 linktr.ee/donslife - Links to all of my products and discounts
Nice video. I had mine PPF'd while the shop was wrapping my car, but then had to replace the headlights, and now I see how much stone chips the headlights get without the protection, its a huge difference
Great vid, great job! Loved the precise trimming! It'll be a little more difficult on lights that have more rounded edges. I think thats where a little heat would be needed to help the film conform.
@@Donslife Although I am keen on getting PPF done on headlights to avoid stone chipping. Detailing workshop suggested not to apply PPF on headlights with the above reasoning. Not sure if that’s true. Thanks for your reply.
Slate Smoke by Xpel, if installed properly would be a very cost efficient way of achieving the look you want. Also as it wears down it is cheaper to replace than a headlight housing
These new Expel headlight protection kits now reduced to just thin film. Their old headlight protection kits (from maybe 10 years ago) were at least 10x thicker and protected headlamps from up to 120mph flying rocks. I installed the old kits on my cars and they still look good more than 10 years later. I bought the same headlight protection kit for new car, and I was disappointed in what they have been reduced to. Quality have changed or cost cutting. Sad, really.
Totally depends on the headlight setup. If it is relatively easy I say go for it. Sometimes complicated lights are better to leave mounted so you can use both hands to work the film. That’s harder to do with the headlight loose.
Did you do the headlights in your AT4? I have similar lights in my 2020 Sierra and due to their shapes was concerned if I could do this or would need a professional.
I have a question for you. I have a 2008 Porsche CayenneS & that protection film is on my headlights & it's peeling off. What's the easiest way to get it completely off so I can reapply it. I tried using a razor & utility knife but it's coming off in little pieces. I noticed that the only way I'm getting any where with it is when it's wet.
@@Donslife The only problem with that is that they have to be plugged in. I have to do it outside, I live in a condo. I don't have a garage where I can pull my car into. I'm pretty sure they don't make them cordless or battery powered. But if you have any other ideas please let me know. Thanks
@@susangoldberg1108 I found that hot water does the trick too. Use a spray bottle and spray a small area at a time. It will get cold eventually, but if you can't plug anywhere, I'd say that's the route to take. You can make it easier on yourself by starting on a hot summer day, after the car sat in the sun for a while. You might not even need extra heat.
It may be the same. Xpel, 3M, Ravoony, VViViD,etc. they all have brands but if it is a rubbery plastic film for preventing rock chips it is likely ppf. They come in various thicknesses and some resist yellowing
Thank you for watching a video about protecting expensive headlights whether they are easy or hard is beside the point. Maybe people that have easy to protect headlights will try it themselves and be happy videos like these exist. Feel free to leave a link here to your UA-cam channel.
XPEL used in this video: XPEL Paint Protection Film - amzn.to/3LjPaiW
VViViD Premium Utility Blade (my favorite): amzn.to/39TIUP3
linktr.ee/donslife - Links to all of my products and discounts
This guy is great, quick, helpful and to the point!
Nice video. I had mine PPF'd while the shop was wrapping my car, but then had to replace the headlights, and now I see how much stone chips the headlights get without the protection, its a huge difference
Great vid, great job! Loved the precise trimming! It'll be a little more difficult on lights that have more rounded edges. I think thats where a little heat would be needed to help the film conform.
Love the paint on that car so cool. 😍
Nice man, it looks like you’re not cutting the film but rather scoring it so it can be peeled of along the line, epic!
Exactly!
PPFs are UV resistant. The heat emitted within headlight will not be able to disperse resulting developing cracks on the headlight due to overheating.
Maybe..I had 3M ppf on one of my vehicles for 7 years (longer than normal) and the headlights were mint
@@Donslife Although I am keen on getting PPF done on headlights to avoid stone chipping. Detailing workshop suggested not to apply PPF on headlights with the above reasoning. Not sure if that’s true. Thanks for your reply.
Would it be a benefit to let that film sit after wetting and squgeeing and set up before trimming?
It can be yes. Especially in complex areas
it more easy than I thought. Thanks man 👍🏻
How would this perform if used over polycarbonate windows? Would it outgas or not be so clear?
Hello there. What you use between ppf and headlight, soapy water or just water?
Johnson’s Baby shampoo (a few drops) and distilled water is great
@@Donslife thank you
Very informative, do they make a smoked film and do you think it is worth it to smoke the headlights instead of purchasing new smoked headlights.
Slate Smoke by Xpel, if installed properly would be a very cost efficient way of achieving the look you want. Also as it wears down it is cheaper to replace than a headlight housing
What's your thought on pre-cut ppf vs the whole piece. Which one would be easier to work with.
Precut is easier to work with, but precut usually comes in a little shorter to avoid lifting edges from improper installation.
These new Expel headlight protection kits now reduced to just thin film. Their old headlight protection kits (from maybe 10 years ago) were at least 10x thicker and protected headlamps from up to 120mph flying rocks. I installed the old kits on my cars and they still look good more than 10 years later. I bought the same headlight protection kit for new car, and I was disappointed in what they have been reduced to. Quality have changed or cost cutting. Sad, really.
All I could get brother.
Would you recommend taking the light off the car and doing it. Not sure if I trust my hand with a knife that close to my car
That's what I did on my previous vehicle.
Totally depends on the headlight setup. If it is relatively easy I say go for it. Sometimes complicated lights are better to leave mounted so you can use both hands to work the film. That’s harder to do with the headlight loose.
Did you do the headlights in your AT4? I have similar lights in my 2020 Sierra and due to their shapes was concerned if I could do this or would need a professional.
Can I use this on my rear lights also?
Any hard flat and smooth surface you can use it.
@@Donslife ok, and it doesn’t alter the light emitted or make the lights look aesthetically different?
@@anakshan you won’t even know it is there unless you left air bubbles or rough cut edges behind
@@Donslife 👍🏽
I have a question for you. I have a 2008 Porsche CayenneS & that protection film is on my headlights & it's peeling off. What's the easiest way to get it completely off so I can reapply it. I tried using a razor & utility knife but it's coming off in little pieces. I noticed that the only way I'm getting any where with it is when it's wet.
A steam cleaner will help. Adds heat and vapor at the same time
@@Donslife What type of steam cleaner?
Amazon should have some kind of steam cleaner for automotive cleaning projects. They aren’t too expensive. There are so many brands
@@Donslife The only problem with that is that they have to be plugged in. I have to do it outside, I live in a condo. I don't have a garage where I can pull my car into. I'm pretty sure they don't make them cordless or battery powered. But if you have any other ideas please let me know. Thanks
@@susangoldberg1108 I found that hot water does the trick too. Use a spray bottle and spray a small area at a time. It will get cold eventually, but if you can't plug anywhere, I'd say that's the route to take. You can make it easier on yourself by starting on a hot summer day, after the car sat in the sun for a while. You might not even need extra heat.
Flatley Grove
Thanks, Nice video
Glad you liked it!
Great video. Thanks.
You betcha!
Will this help prevent yellowing?
I think it would help since it resists yellowing itself
@@Donslife good deal, thank you!
Rosamond Dam
So there is no difference between a headlight film and a ppf
It may be the same. Xpel, 3M, Ravoony, VViViD,etc. they all have brands but if it is a rubbery plastic film for preventing rock chips it is likely ppf. They come in various thicknesses and some resist yellowing
Schinner Forest
Rutherford Ridge
Kertzmann Wall
Runolfsson Circle
Schamberger Trace
Use distilled water instead of tap water
Definitely preferred
Stay firsty my friends
Aliza Avenue
Bartell Plain
Fadel Bridge
Ortiz Prairie
Spencer Ridge
Rolfson Causeway
Hickle Bridge
Weimann Bypass
Thompson Loaf
Corwin Manors
Brekke Summit
Heathcote Ports
Lind Mission
Erdman Divide
Dakota Ramp
Graham Loaf
Keebler Port
Kamille Park
Brenda Ridges
Zoey Knoll
Jeff Causeway
Asha Landing
Boyer Course
Bernhard Heights
Vesta Loaf
Schmeler Centers
Betsy Tunnel
Schoen Isle
Evert Mount
Alden Pines
Waino Forks
Ted Fords
Sofia Rapids
Hagenes Union
Mekhi Harbors
Pauline Stream
Ed Mall
Sorry don’t know Ed Mall
You choose the easiest headlight to do lol anybody can do that 😂😊
Thank you for watching a video about protecting expensive headlights whether they are easy or hard is beside the point. Maybe people that have easy to protect headlights will try it themselves and be happy videos like these exist. Feel free to leave a link here to your UA-cam channel.
Yeah it's a little ridiculous for a hunk of plastic.
Except the hunk of plastic for my 2010 is around $1000.... Each.
That paint wrap looks like dust... stupid
Thank you for your contribution
Woman ☕️
@@Donslife your smart mouth doesn't help make it look any better.
@@Solid_Snack sorry, I wasn’t trying to be offensive. The wrap was a prototype film I was asked to review. It was neat at the time.