P2122 P2127 Code Fix - 350z Throttle Not Working
Вставка
- Опубліковано 22 сер 2024
- My 350z throttle quit working, it just went dead while sitting at a traffic light. I scanned for codes by the roadside and found P2122 P2127. I suspected the 350Z TPS (Nissan 350Z throttle position sensor) was bad, but it wasn't nor was I too far off from the problem. More faulty rubber bump stops! Time to just replace them all with more permanent solutions!
⚫Stuff seen in this video⚫
Code Scanner ▶ amzn.to/3zHcF0H
Updated Code Scanner ▶ amzn.to/3xxIAyY
Rubber Bump Stop Pads ▶ amzn.to/3iUuXFT
Bolts, nuts, washers ▶ amzn.to/3cVV4s9
Can of Coca Cola ▶ amzn.to/3zJ1LYn
I took a trip down to Coca, FL to Classic Car Creations to see Earl and Eleanore, my 1956 Chop Top Oval Window VW Beetle. There is so much happening here! Thanks Earl!
Subscribe to Earl ▶ duckshit.net/ccc
⚫ Consider Supporting This Channel!⚫
GET MERCH ▶ duckshit.net/store
PATREON ▶ / duckshit
RUMANDCOLA FUND ▶ paypal.me/duck...
⚫ More Popular DuckmanCycles VW Videos ⚫
⚫ 1967 VW Bus Restoration Playlist ⚫
Gregory ▶ duckshit.net/gr...
⚫ 1956 Chop Top VW Beetle Restoration Playlist ⚫
Eleanore ▶ duckshit.net/el...
⚫ Engine Stuff ⚫
Valve Adjustment ▶ • VW Valve Adjustment /...
Setting Static Timing ▶ • How to Set VW Beetle E...
Lift Engine/Engine Stand ▶ • VW Engine Stand - How ...
Replace Clutch Cable ▶ • VW Clutch Cable Replac...
Remove Crankshaft Gear ▶ • VW - Removing Cranksha...
⚫ Body / Rust Repair / Restoration ⚫
Remove Beetle Body ▶ • Body Comes Back Off - ...
VW Body Lift and Dolly ▶ • VW Body Lift / VW Body...
Reinstall Beetle Body on Pan ▶ • VW Beetle Body Put on ...
Bolting Beetle Body to Pan ▶ • VW Beetle Bolting Body...
Rust Conversion ▶ • Rust Conversion - ROTT...
⚫ Floor Pans ⚫
Replace Beetle Floor Pans ▶ • Replace VW Floor Pans ...
Replace Pans (Eleanore) ▶ • Floor Pan Replacement ...
Replace Karmann Ghia Pans ▶ • Replace VW Floor Pans ...
Replace Thing Floor Pans ▶ • Replace VW Floor Pans ...
Replace Type 3 Floor Pans ▶ • Replace VW Heater Chan...
Flip Floor Pan By Hand ▶ • Flip VW Pan by Hand
⚫ Electrical ⚫
Replace Dimmer Relay ▶ • Howto Replace Air Cool...
Hard Start Relay ▶ • Howto Install a VW Bee...
12v Starter Differences ▶ • 12V VW Starter Differe...
⚫ Brakes / Suspension / Drive ⚫
Tie Rod Replacement ▶ • VW Beetle Tie Rod End ...
Packing Wheel Bearings ▶ • Grease Packing VW Whee...
Lowering/Brake Upgrade ▶ • How to Lower your VW B...
Lower/Raise Rear Torsion Bar ▶ • Torsion Bar Removal/Re...
Flaring Stainless Brake Lines ▶ • Making Flared Stainles...
More Flaring Stainless Lines ▶ • Flaring Brake Lines - ...
Replacing Rubber Brake Lines ▶ • Air Cooled VW Rubber B...
Residual Pressure Valve ▶ • VW Rear Disc Brake Res...
Install Rear Disc Brakes ▶ • VW Type-3 Rear Disc Br...
Bleeding Brakes ▶ • How to Bleed Your VW B...
Pack/Install CV Joints/Axles ▶ • Drive Axles / VW CV Jo...
Replace Lug Studs ▶ • How To Easily Replace ...
⚫ Type 3 Specific ⚫
Remove Type 3 Engine ▶ • ASMR - VW Type-3 Engin...
Install Type 3 Engine ▶ • VW Type-3 Engine Insta...
Type 3 Dual Carb Linkage ▶ • Type-3 Dual Carburetor...
Type1 Trans Mount in Type3 ▶ • Custom VW Type-3 Trans...
⚫ DUCKMANCYCLES FACEBOOK GROUP ⚫
JOIN THE DISCUSSION ▶ / duckmancycles
⚫ FOLLOW MY SOCIAL MEDIA ⚫
FACEBOOK ▶ / duckmancycles
INSTAGRAM ▶ / vvtheduckvv
TWITTER ▶ / vvtheduckvv
⚫ MY WEBPAGE ⚫
GET EARLY ACCESS TO VIDEOS AND MORE: duckshit.net
⚫ SUBSCRIBE TO MY OTHER CHANNELS ⚫
SkeeterTheDuck ▶ / skeetertheduck
VvTheDuckvV ▶ / vvtheduckvv
DuckmanCycles ▶ / duckmancycles
Theme song (Gearhead) by Kevin MacLeod/Incompetech.com
Background song (Saschas Things) by Sascha Ende/filmusic.io
Been a little while since I did a 350Z tech video of any kind.... but hey, it seems to break more than the VWs do these days. This 15 year old car vs 50 year old cars.... What's your feelings on that?
I reckon very few of these newer cars will be around in 50 years time. They are nice to drive and reliable for a few years, but tricky to diagnose and repair (except for The Duckman maybe!). Then again, my eldest son (age 14) is as passionate about cars like your 350Z as I am about VWs, and is learning how to maintain and modify them, so maybe a whole new generation will treat these Imports with the same care we oldies do with our classics?
As for EVs...nah.
With so much tech these days, there is so much more to go wrong. I think that is why older cars are becoming more popular. Less to go wrong, easier to repair/diagnose, and in most cases cheaper too. Only problem is availability of spare parts.
@@100Jeanluc Spare parts may be an issue with some older cars, but certainly not classic VWs: The aftermarket VW parts business seems to be thriving and at least here in New Zealand, is growing. The value of older VWs is also rising they are now quite an investment.
@@martinharris5017 very true, but there are other vehicles besides vw's. Too many to have spares for, but that's the way it is.
@@100Jeanluc I agree.
Started watching, went out to the Z and saw all those little green pieces just like yours. 😂
Thanks for the help!
Hahaha awesome! I. Noticed some of the shrapnel laying on the ground for weeks in advance of the problem fully coming to light. I’m glad you got it figured out. Thanks so much for the comment!
ABSOLUTE LEGEND. Just saved me so much time and stress and money, once I saw the green plastic bits I KNEW. Thank you so much 🙌
Thanks much for the feedback! Glad I could help! Sometimes the simplest solutions are the best for a hard problem!
Thanks for the video, what a simple fix. We had this issue with our Z last year but since none of us are mechanically inclined, room mate took it to a shop and paid $500 for someone to work their magic.
Oh man, such simple things that happen to this car, and so far I've managed to always fix them. Thanks for your comment!
You sir, are a life saver. Bless you.
Found the same green broken pieces. Ordered new pad.
Thanks again. Gio
I'm so glad I was able to help you! Thank you for the feedback!
could I just order the exact part or would I have to get a whole other pedal ?
This happened to me yesterday. Noticed the little green plastic thing broke in half on the floor and realized it came from the accelerator also. This video was awesome. Same symptoms and bam got it fixed within 30 minutes!! Thanks dude!
Thanks so much! So glad it could help!
Man, thank you so much for this video! Saved me a tow fee and likely hundreds maybe even thousands of dollars at the stealership. They’d have told me I needed a new throttle position sensor, new pedal assembly and harness and then a new ECU!😂
Yeah I hear ya! All that billing totalled, and they still wouldn't have found the problem, and you'd have already spent more than the car was worth!
Thanks so much for making this video, my car was left in a parking lot for a week while I was trying to figure this out, bought a new throttle body with position sensor, $210, still no throttle, I saw your 2 yr old video and it was right on the money, was able to get the car home. You rock, 👍😁👏
Thanks man! I wish I was able to find this video before I made it.... haha! I had to drive home at idle speed (which was a little higher than normal with this error) and it was only a couple miles but I made it! 😁👍🦆💩
this happens to me 1 week after finally fixing my car that sat for 9 weeks with a broken transmission. Dude thank you I was about to scrap my Z.
Cars are Pain.
Oh man... lol. At least it was a low tech problem, right? Glad you got it fixed! 😁👍🦆💩
This was a lifesaver. I literally was about to replace all kinds of sensors didn’t know what was wrong with the car but looked at the floorboard and like you say in the video little green chunks of rubber where everywhere $12 part at the dealer and good to go. Thank you !!!
You're welcome my friend, I'm glad it was an easy fix!
Thank you so much bro, my brother and I just bought a Z to flip and the throttle stopped working randomly when he got in it. Popped a random screw and nut and bam it’s up and running again!! Thank you so much dropped a like!
Haha too awesome! Thank you for the comment! Glad I could help!
I was stranded super glued a couple of pennies together put them in place of the spacer that fell out put the pedal back and was good to go...easy fix.
That'll get ya home! Good work!
This just happened to me today. I looked it up on you tube and here was your video. Did the quick fix and it works great.... Thanks... You saved me a big headache.
Too awesome! Thank you for the feedback! So happy I could help!
Me too!. Luckily I was close to home and was able to cruise on my driveway. Watched the video and got it fixed quick! Cheap ass parts!
Yeah, nothing to it! Hope you perma-fixed it with a nice bolt!
Thanks DuckMan! Found your post and fixed my issue within the hour! Many Mahalos from Hawaii! Next going to also work on my '89 Westy :(
THIS HAPPEN TO ME LAST NIGHT ,,,,,,I KINDA SUSPECTED THE SESOR HAVING AN ISSUE
BUT THIS VID REALLY NAILED IT ,,,,,, EXCELLENT, THANKS
So excited you yelled about it to the world! LoL! Much appreciated my friend! I'm glad I could help! Thanks much for the comment!
You sir are a life saver!!! Quick fix thank you so much!
Glad I could help, thank you so much!
awesome video! very helpful. my 350 did the same thing.
Did you get it fixed up alright?
@@DuckmanCycles I did!
Thank you sir for this video. Saved me a bunch of time!
Like the Nissan 350z only issue i have with them they are still expensive in south africa. My bug serves my needs 100%. Thank you for all the great videos
Pretty cheap here nowadays! Parts are getting a little harder to find, though! Some things are discontinued!
@@DuckmanCycles i agree. Seen spare prices for certain cars is insane. Most people would go too dealers too buy parts. Your throttle assembly here if you buy it and turn into usd is quite pricey.
@@pierreduplessis1507 throttle is very pricey even over here, but if I can find one in a junkyard it would be pretty cheap
Thanks man. Good explanation of the dash lights and what happens to the fuel pedal parameters when the spacer breaks.
I appreciate the comment! I hope this helped you! 😁👍🦆💩
Hell yeah, nice working with what you have!
That's what I'm best at.... demonstrated time and time again haha!
@@DuckmanCycles say it isn’t so…. 😂😂
@@VWJawbreaker Pfffffffft! HAHAHAHA!
What is the green bushing thing called. I just did the trick of not taking my foot off the pedal and the slip and traction did not come on. You are the man!
Comment, please check the video description for more information! All the answers you seek! I planned ahead!
I watched it all. I have no idea why. But I did. Hope the weather there gets better so you can play with your VW's.
Well, hopefully because the video was entertaining interesting, or educational.... otherwise that is kind of a rude remark! :-P
@@DuckmanCycles Never try to send a rude remark. In fact, I had sort of that same problem with a Dodge Ram truck. So it may have been educational.
Holy rice paddies Batman you did it! Good job!
Fixed! haha! Thanks!
Thank you so much for the vídeo, it happened today with my son's 350z. I'm just seated next to the car after fix the problem taking a look in the comments.
I hope you got it taken care of!
First thing in the morning, I'll check it on my Toyota. Have the same problem, mostly P2122, sometimes P2127, once P2121. Thanks😁
Hopefully you'll find something similar and makes it easy to repair! But it is a different manufacturer with a different part... could be anything! 😁👍🏻
This fixed my nissan e51 elgrand thanks
Glad I could help! Thank you for the comment! 😁👍🦆💩
You are the best, thanks for your help, now, I now how to fix my 350z 2006, God bless you 🙏!!!!!
Thank you so much, I'm so glad I could help you!
Thanks for this. Had similar problem, and fixed it with the help of this video.
Thanks Paul! I'm glad I could help I appreciate the comment! Thanks again!
From sad to again happy in 20 min tks sooo much.
Thank you for the comment! I'm glad I could help!
Where can I find the OEM piece by itself? What is it called and can I find it at like Autozone ?
Thank you so much keep the videos up! You are very helpful grateful 🙏🏻 for your help
Thanks Jonathan, I'm so glad I could help. More videos coming up on this one the next time something breaks LOL! 😁👍🏻🦆💩
Thank you so much! It helps a lot!!
Thanks from brazil
Thank you for watching!
Hi Duckman, Id see no point in using the OEM part as it'll fail again because they are designed to do that and what an inconvenience when they do. Great job.
Yeah, but OEM part lasted 16 years.... I do wonder if rest of car will.... haha!
Wow! Thank you thank you thank you! 🙏🏼
Thank God that's all it was!
Sometimes we get lucky and the low-tech solution is the best fix to a high tech problem! Glad I could help! Thanks for the comment!
I got same the same two codes rubber pad is good , changed the throttle p sensorand still have the code with ,service engine soon,
Car drives for 1 minute then losses power and have to turn off for a good minute then drive again repeat lol , accelerator also stops working when loss of power happens but works just fine at start of car
Broooo ! I see those light went I crank my car today and I say F???? I look on you channel and bingo 🎉thx for safe my life today bro ❤❤❤❤😂
Oh mannnn.... I'm glad you found me! I hope this video helped you out! Is everything all good now?
@@DuckmanCycles bro!!! Perfect thx to share you knowledge, you’re the MAN.
Thank you sir!!
Most welcome! Hope I was able to help!
Nice repair. Very helpful !!
Thank you, it's been good since!
Gracias
And thank you for your comment!
meanwhile it took me 3 hours to unscrew the top bolt, I put the seats down all the way and went under my steering wheel on my back (my feet touching the roof of the car), like some kind of diagonal "sleeping on back" position
That was pretty much what I had to do to replace the air conditioner, but I am too big to put my feet up, they had to go into the trunk lol!
Hey man appreciate the help
Thanks for the comment! So glad I was able to help you!
bruh this video saved me from buying sensors! thanks so much my man!.. one question do you need to relearn the throttle after disconnecting or i should be fine?
Well very specifically, the throttle pedal can be disconnected without having to relearn. But if you start messing with the throttle body that might be a different story. Hope that helps!
Life saver! Thank you!! 🙏 🙏
Hey thanks for the comment glad I can help!
I have the same issue. But my green bit is still in there in great condition. What should i do?
Make sure its not flat, or pushed in too far. That could also lead to the same area, if uncertain, replace it. That's where i'd start. :)
Thank you for sharing your video it was so helpful..
Thank you! I hope you got your car straight!
Ok quick question. What if the green piece is still on the car? What else can it be?
Tough to say, you didn't give me any symptoms of the problem you're having. ¯\_(ツ)_/¯
The brake and clutch pedals have the same issue. Already did the simple fix on those, now I'm hoping this is way my z won't rev.
I hope that fixes it for you
So what do you think I should replace first if the the stopper is still intact ?
You didn't tell me if you had the same errors, but if you did, then I'd check the wiring first ensure its good, then replace the throttle.
@@DuckmanCycles I have code P2112 paired with P2127. I can accelerate but it’s superrrr slowwww, rpm shoots to redline very quickly and kicks hard from 1st to 2nd.
Great
Thank you!
Saved me some money tonight i was stranded and almost went and bought new throttle body, new pedal sensor but watched this video and had a spare bolt and nut that was the perfect size and got me on the road again thank you ! 🫶🏼
Oh wow! I'm so glad this video helped so many people and got you home safe! Thanks so much!
Hey man i have a question my car doesnt let me rev past 2k rpms and it doesnt go in gear any idea why?
No I certainly don't, is an automatic?
It is so Hard for me to Take the pedal out complet, any tip for doing easy, because the space to get in is so close
I have a little trouble working out of there also because I'm such a big person, but if I can do it pretty much anybody can! It was a lot easier than taking the pedal cluster out of my Volkswagen Beetle!
Whats the green pad called Duckman???
Links in the video description! Thanks for the question!
I had a Nissan pickup that ate those damn things after buying a good many I finally used a bolt ...
Bolt seems to be the way to go!
I have the p2122 and p2138 found the broken green bits. Replaced it. No change. Replaced throttle assembly no change. Some say it’s the throttle body. Don’t want to just throw parts at it.
Car sat for over a year and when I got it going again this issue was present. Any help will be appreciated
Ensure the new rubber stop is indeed high enough to prevent the pedal from extending beyond its effective range.... that small amount is ridiculous, but enough to affect operation. In other words, try taping a penny over the rubber bumper. Do this when the car is off, of course. Then try and start it, see if that fixes the problem. Maybe you need a bigger stopper.
@@DuckmanCycles I have a brand new pedal assembly in place now same codes. Will not re learn. I have cleared codes but they come back instantly.
I have checked pins in connector at pedal and at throttle body. All seem good.
I have a new battery in place but the battery is very bottom of the barrel in cost. Only thing the battery has is lower CCA compared to the more expensive ones. It is a new battery not re manufactured or used.
I tried the pedal trick holding it down a little before starting and no change as well.
I’m going to check the relay by the battery next.
I disconnected the battery for 15 mins prior to new pedal assembly installation, codes were present as soon as I started vehicle.
Car had no issues prior to sitting for over a year.
I don’t see any wire damage from critters
Wish I could share a picture but I did have a chewed wire. In the battery compartment there are three connectors on the fender wall. Yellow wire was chewed. Made a repair and cleared codes all is good. I do appreciate you responding so long after your video posted. Hope my issue will help others
Oh wow, I'm so glad you found that! Little troubles like that are certainly hard to pinpoint! Thank you for the feedback and thank you for sharing! 😁👍🏻🦆💩
I am having problems with my 2006 Nissan Murano, Code P2122, P2138 and P0643, Changed Pedal, Changed Trottle body and still car won't accelerate. Once TPS or Pedal changed car drives for a while like 1km and it goes to limp mode with Slip light and VDC displaying a check engine light, when I disconnect the pedal cable the car get high acceleration can drive . But it's slow. please any suggestions for possible solutions?
I'm no expert with a Murano, and those errors are different than my 350z. But you'll have to do some checks per the manual with a voltmeter and ensure the individual systems and sensors are doing what they are supposed to. I hope that helps for what it's worth! Thanks for the question!
I did this fix the same way you did on a limp g35. The throttle works now and the vdc and slip lights turned off, but how do I get the check engine light to go away without a scanner?
I don't think you can. but a scanner can be had as little as $15-$20 anymore. Its worth the investment! amzn.to/3py414t
@@DuckmanCycles I'll look into getting one. The bolt seems to work fine, but my car definitely isn't revving as high (seems to cap out around 3500). I'm assuming it's some safety feature (while the engine light is on )and not an issue with the bolt I put in?
Mine just did the same but it shows different codes I don’t know if that’s still gonna fix the problem
Yeah, probably not, but check for the rubber plug anyway! Maybe it will solve some of them, then you can more easily sort out the others! Hope that helps!
@@DuckmanCycles where do I find the rubber plug??
Links are always in the video description. 😁👍🏻🦆💩
Iv just fixed my g35 it had the same problem I did what you said with the throttle pedal and it worked but after 10 minutes it now won't start at all and all the warnings signs are on the dash . Is there anything else could be wrong
Yes, first I would suggest you check anything that got messed with... electical connectors, etc. After that, if problem not solved, the check for more error codes. There is bound to be one in there!
It's still a really cool car
Overall I can say that I’ve been very happy with it!
Duckman I learning that Stop and Go Traffic is Now Much More fun!!!; ) Thank's Duckman!!!; )
Haha thanks!
dude, u save my day. i solve it on my lady too.
Awesome, so glad I could help you! :-)
The piece is still there the rubber part so what could my problem be
Hi Fred... did you watch the video?
@@DuckmanCycles yea the part you replaced wasn’t broken for me but I have the same code
Then it'd be safe to say bad pedal or problem in wiring.
I've been dealing with the sliplight an no throttle
Only 22 hundred rpm done replaced both throttle body's an maf seners any more advice would greatly appreciate
You didnt mention codes, start there. TPS, not mentioned either, could be that or related to that.
Been going on for 4 years think I'm gonna try you trick if it don't fix it time for ls swap
Hope that gets it, but don't forget to read the error codes!
Spent $70 at the u pull it, for a new throttle body only to find this after it didn't work. But I know better and should have done more diagnostic tests. Less learned don't be a parts changer.
Save that old part though, and fix it. Someday one of them is gonna go kablooey! 😁👍🦆💩
@@DuckmanCycles yup not even worth trying to sell it at this point. Most I could get out of it is an exchange for some other parts.
@@g.wes.3906 I'd stick it in one of the cavities around the spare tire and know its ready to go for next time! :)
@@DuckmanCycles or next owner.
Good old technology. Trial by fire lol
Thankfully been easy to fix so far!
So I've got these codes but my little rubber deal is still. Intact. The throttle plate doesn't move at all when I hit the gas and the ecu reset doesn't change anything. Bad throttle body?
Most likely, or the wiring is loose or cut somewhere. Easy to swap out TPS and see. Keep in mind that after you swap it you'll need to recalibrate it. I don't remember the process, but you can find it on Google I'm sure! I hope that I've helped you!
@@DuckmanCycles thank you sir.. I'm going to just start replacing stuff anyways since the car sat for over a year. Might as well start with that.
Yep! Hope the fuel is still good in there!
@@DuckmanCycles it was empty.
Hopefully not too much residue in the lines! 🙂👍🏻
Can you do more videos on ur 350z please ??
Yes, whenever something comes up! Thanks for the request! I've got one pending right now,
@@DuckmanCycles you’re welcome and thank you !!!
Much appreciated!
I have that problem
I hope this helps you!
Such a stupid design fault & for people who are not mechanically minded would take it to a garage & end up with a big bill as they would i guess replace the whole throttle pedal without finding a cheaper method of repair, hope you are doing good Glen
Thank you! And yes I am doing great!
I have 03 350z i just clean my TB and change my spark plugs and now its starts but only for 3-4 sec and I noticed my TB not opening when i press my gas pedal, need help please
You did not say what method of throttle body cleaning that you decided to do, but if you tamper with the throttle body you have to resync/calibrate it. There is a process to do this, make sure it's still plugged in properly, then hit up Google and search for the process of how to do that. Some kind of turn the key on and step on the gas pedal for 10 seconds turn it back off and pump it 32 times while standing on you head kinda thing. I hope that gets it for you!
@@DuckmanCycles i take out the throttle body because i need to clean it good, i will do it after i work the relearning for that
Then yes, the calibration has been disrupted. The 350Z ECU doesn't like it to be removed, make sure it's connected properly and then recalibrate according to instructions .
@@DuckmanCycles will do sir
I hope I helped you! 😉👍🏻
Hola amigo
Hi!
So I'm having the p1122 and p1126 codes. Hearing this is the throttle body itself. Anyone else have an idea? I'll buy it if that's the problem.
Get a used one from junkyard, save some money. Maybe you'll get lucky!
@@DuckmanCycles I did.. Same issue still. Same codes. Took ipdm apart and it looked good too. Guessing it's a wiring issue
@@earthisfat6184 update??
@@mamunbaser8683 car is still sitting there. I work so much I have no time. Just last week I pulled the fuel pump and my fuel is red and rusted. Almost looks like someone put something in it. So my current project is cleaning the tank.
Did I miss a video about that honda in the driveway 🤔🤔?
Yeah, practically every video last summer! 😮
@@DuckmanCycles damn. I must have just forgot then
Or you hibernated! Lots happened!
@@DuckmanCycles 🤣🤣🤣definitely possible. I also have a bad memory of things. I probably even commented on the video 🤣
@@jamesk3565 I dunno how you could forget any of that!
It would drive me crazy until I 3D printed a new button... then I would probably leave it in the glovebox for the next 10 years...
I have considered printing one, but I think 3-D print it would probably Or fall apart kind of easy. Not likely to last anywhere as near as long, but that doesn’t mean I couldn’t print out a whole bunch of them.
I wonder who was the effing genius, that decided:
Hmm throttle cable, is literally perfection. I know! Let’s digitize it, put an extra pos sensor that is prone to breaking, and turn an organic driving experience into one that resembles a video game.
Automotive engineers need to be fired and replaced by experienced mechanics.
Hahaha! I just had that drive-by-wire conversation with somebody else on Twitter yesterday. The computer is what controls the car, you can only influence the computer, you really don't have any control. Some systems are pretty bad and have a very noticeable lag that creates a horrible Driving Experience. My Z does this too, but thankfully not as bad as others, and much better when traction control is off. I'll keep the throttle cable on my VWs!
@@DuckmanCycles
I have 5 vehicles, Honda Prelude Sh, s13 and s14 with sr20 and 1jz in various stages of disrepair, this 2003 350z and 03 Ram hemi.
Throttle response on the Honda is literally perfection. Why would any genius mess with that? The sr20 is pretty darn good, but the turbo lag can dampen things a bit sometimes.
😎🖖✌👍👌😁
Thank you!
hey could you plz help, i have a voltage problem, replaced alternator and battery checked fuses and wiring and still no fix.
You would have to explain to me your voltage problem... maybe I can help!
@@DuckmanCycles Well at initial start up the voltage is 14.5 then immediately drops to 12.9 and sometimes the battery light comes on and off at this time the voltage will be 11.8 then it goes back up to 12.9
Check all of your connections, maybe even a bad battery terminal. I had a bad one, it would drop the voltage so low it would sometimes shut the car off.
@@DuckmanCycles the are both on tightly
@@yuhfiknowtv In particular my positive one was also on tight, but it was no good. When I messed with it, it began to fall apart.
Thank you
Did it help ya? Thanks so much for the comment!
@@DuckmanCycles yeah got stranded on the side of the road tried playing with the throttle body and mass air flow sensor which got me nowhere so I googled it and your vid saved the day luckily I had a 10mm bolt and nut and ratchet so I just slapped it in right there and boom good to go saved me on a tow truck fee gotta love UA-cam lol
@@markculp1992 Oh wow, tahts a winner! I wish I had this video for me when it happened... but I was close to home and just idled through the gears with the AC on to keep it throttle up a little..... for what its worth! But I put a penny and a piece of tape when the clutch sensor didn't wanna let me start the car haha... I was on a hill anyway so it didn't really matter too much. But its fixed, too, now! Thanks so much for the feedback and the comments!