How to FIX Baseboard Leak

Fire Extinguisher leak in baseboard heater including Tools and supplies used in the repair process.
TOOLS
Milwaukee Copper Cutter: amzn.to/3ung16J
Milwaukee Drill: amzn.to/37JeKNl
Milwaukee Pen Light: amzn.to/3qVUD6s
Bernzomatic Torch:amzn.to/2NASTRl
Wire brush for drill: amzn.to/3qJWomZ
Tape Measure: amzn.to/3kf7UEw
Sheet metal cutter: amzn.to/2Nq3uid
Reamer: amzn.to/2OYtHEM
Needle nose pliers: amzn.to/2ZJ61Gu
Mirror: amzn.to/3pPwcWA
Fire Extinguisher: amzn.to/2ZMYGFX
SUPPLIES
Emery Cloth: amzn.to/3dOUBJw
Solder: amzn.to/3qOGM1r
Flux: amzn.to/3kh8NfC
Flux Brushes: amzn.to/3r1NzF2
Rubber Gloves: amzn.to/2NCedGj
3/4" Coupling (with stop): amzn.to/2NDarMG
3/4" Repair Coupling (NO STOP): amzn.to/2NZOqb2
((( Post your questions in the comments and remember to subscribe! )))
"WARNING" - Do not attempt to work on or disassemble any part of your HVAC System if you're not a Skilled Technician. You assume any and all responsibility. Working on HVAC Systems can be VERY DANGEROUS and should only be performed by Highly Trained Technicians.
Thank you for your watching our videos.

[@ufoinsider6932]

This is an excellent video!

[@mbond0027]

Awesome vid man, thanks!

[@paulscott9083]

Awesome video, information and instructions

[@furnacetech2581]

Thanks for watching!

[@BeardAxeMcAxeBeard]

You're awesome thank you

[@TheDrewflav]

Did you have to drain whole boiler system line prior to cutting copper radiator??

[@furnacetech2581]

No, I have isolation valves in each heating loop.

[@watr77222]

Hi, how would you suggest detecting location of heating pipe for baseboard water heater behind wall? Former owners severed the pipe in the boiler room for the basement. Thanks!

[@furnacetech2581]

That’s a tough one! My best suggestion would be to start where the end of the baseboard run is located and work from there. You can cut small inspection holes to limit damages. I hope this helps

[@bobwelch5056]

Thank you

[@furnacetech2581]

You're welcome

[@JS-go1gu]

Satisfying!

[@furnacetech2581]

Thanks for watching!

[@valeriehofmann2615]

To bad this happened st night and only have elbows. Got it together and still leaking at the soldered seams

[@HonestDiner-cz4op]

Could you have done that repair with a ProPress?

[@furnacetech2581]

I don't see why not. I just don't use ProPress personally.

[@furnacetech2581]

Tools and Supplies I use in this video:
TOOLS
Milwaukee Copper Cutter: amzn.to/3ung16J​
Milwaukee Drill: amzn.to/37JeKNl​
Milwaukee Pen Light: amzn.to/3qVUD6s​
Bernzomatic Torch:amzn.to/2NASTRl​
Wire brush for drill: amzn.to/3qJWomZ​
Tape Measure: amzn.to/3kf7UEw​
Sheet metal cutter: amzn.to/2Nq3uid​
Reamer: amzn.to/2OYtHEM​
Needle nose pliers: amzn.to/2ZJ61Gu​
Mirror: amzn.to/3pPwcWA​
Fire Extinguisher: amzn.to/2ZMYGFX​
SUPPLIES
Emery Cloth: amzn.to/3dOUBJw​
Solder: amzn.to/3qOGM1r​
Flux: amzn.to/3kh8NfC​
Flux Brushes: amzn.to/3r1NzF2​
Rubber Gloves: amzn.to/2NCedGj​
3/4" Coupling (with stop): amzn.to/2NDarMG​
3/4" Repair Coupling (NO STOP): amzn.to/2NZOqb2
Thanks for watching the video! Click the link to SUBSCRIBE: ua-cam.com/channels/-ZPTqzkJujjUouZZohAvDw.html