Back in the late 80's early 90's when I worked at Westinghouse In Sunnyvale, CA I used a power scrapper to make steam turbin housings steam tight. It takes a year to be any good at this, either you aquire the ability to do the job or you have to move on to something else.
Hi! Last job done with that scraper including precision bubbles, straight edges and smaller plates was one pretty big cast iron surface plate. It was a hard work even with power scraper, but without it, it would have been hell. I didn't film that but scraper still works.
Hi! This was just scraped to demonstrate the scraper in action, but the plate was also getting better, though not perfect yet. Also the scaper was cutting pretty large areas and I wasn't aiming for any specific "points per inch"
@@GarageOfTool but then i think all point of video is lost because you are "hiding" end results. its just looks like scraper did very bad job and you dont want to show last blueing because scraper is useless. its just first impresion after watching video, probably you got great flatness but watchers cant see that without blueing.
@@craftzars Yeah I understand your point, but the final flatness results depends only on how many bluing cycles one is willing to do (pattern will though be more coarse due the long stroke and large radius tool)
Hi! I've been running that scraper for a pretty long periods and it's still running fine. The only thing I would change is the stroke lenght, which could be smaller.
@@GarageOfTool That's awesome! I'm crippled with overbuild-everything syndrome. Neat to see something built reasonably to accomplish a goal. I end up N projects deep when I could have just taken the value add way out.
I've got to do a bit of scraping and was thinking of doing this. How well has it held up and other than making the stroke shorter, would you make any other changes?
Hi! Absolutely no problems 👌, but consider adding balancing weights. And I actually did the most of the scraping of my big milling machine table by hand, so my advice to you is that make the power scraper before, not after 🤦♂️😁
Hi! I haven't tried to do pure flaking with this, but instead, a cross scraped surface will anyway hold oil etc. nicely, so there's a little advantage to add final flaking for most parts.
Iwill say only hand scrapper .power scrapper of course is fast but it can never be like hand scrapper because if you pay attention 100%also som wher of the part will be not corect as all.iuse of hand scrapper ca 20 years also ihave power scrapper. If samoen don’t exapt my experience pleas let me know and why? Thank you Best regards sina-von Austria 🇦🇹
Hi! Yes, this is power scraper is definetely made for the cases where you have to take a lot of material out as fast as possible. Hand scraping is of course more controlled process, but hand scaping e.g. 20 rounds of big surface plate, is a sweaty job
I’m going to make one. Great video
Nice job. I have a couple of cast iron surface plates that need to be scraped. I just might build one of these. Thanks for the ideas.
Back in the late 80's early 90's when I worked at Westinghouse In Sunnyvale, CA I used a power scrapper to make steam turbin housings steam tight. It takes a year to be any good at this, either you aquire the ability to do the job or you have to move on to something else.
Nice, something to think about. Thanks
So smart my friend...........now I will build one........Thank you and Cheers, David (Aus)
It's not how you get there, it's that your there. good job
Ye machine chahiye sir ji
Looks like that works well 8-)
Hey. how are the results from doing a whole plate with the scraper? Any followup? thx
Hi! Last job done with that scraper including precision bubbles, straight edges and smaller plates was one pretty big cast iron surface plate. It was a hard work even with power scraper, but without it, it would have been hell. I didn't film that but scraper still works.
@@GarageOfTool ok. Very nice. Well show us the results when you have time at hand.
why there is no last blueing to see how good scraping was?
Hi! This was just scraped to demonstrate the scraper in action, but the plate was also getting better, though not perfect yet. Also the scaper was cutting pretty large areas and I wasn't aiming for any specific "points per inch"
@@GarageOfTool but then i think all point of video is lost because you are "hiding" end results. its just looks like scraper did very bad job and you dont want to show last blueing because scraper is useless. its just first impresion after watching video, probably you got great flatness but watchers cant see that without blueing.
but anyways great video, i have also plan to build cheap scraper
@@craftzars Yeah I understand your point, but the final flatness results depends only on how many bluing cycles one is willing to do (pattern will though be more coarse due the long stroke and large radius tool)
Curious, the brass pin isn't giving any grief? Did it make it through the rebuild?
Hi! I've been running that scraper for a pretty long periods and it's still running fine. The only thing I would change is the stroke lenght, which could be smaller.
@@GarageOfTool That's awesome! I'm crippled with overbuild-everything syndrome. Neat to see something built reasonably to accomplish a goal. I end up N projects deep when I could have just taken the value add way out.
I've got to do a bit of scraping and was thinking of doing this. How well has it held up and other than making the stroke shorter, would you make any other changes?
Hi! Absolutely no problems 👌, but consider adding balancing weights. And I actually did the most of the scraping of my big milling machine table by hand, so my advice to you is that make the power scraper before, not after 🤦♂️😁
2 nos quantity
Probably a scraper build by people never scraped themself… nice mod!
I've actually scraped tens of hours using this scraper, still working 💪. Beats hand scraping, but obviously PPI is smaller due the long stroke.
How do you do the flaking on this?
Hi! I haven't tried to do pure flaking with this, but instead, a cross scraped surface will anyway hold oil etc. nicely, so there's a little advantage to add final flaking for most parts.
@@GarageOfTool Interesting, didn't know that. I thought half moon flaking was the only way for the oil to stay and lucubrate. Thanks for the reply.
Iwill say only hand scrapper .power scrapper of course is fast but it can never be like hand scrapper because if you pay attention 100%also som wher of the part will be not corect as all.iuse of hand scrapper ca 20 years also ihave power scrapper.
If samoen don’t exapt my experience pleas let me know and why?
Thank you
Best regards sina-von Austria 🇦🇹
Hi! Yes, this is power scraper is definetely made for the cases where you have to take a lot of material out as fast as possible. Hand scraping is of course more controlled process, but hand scaping e.g. 20 rounds of big surface plate, is a sweaty job
Show
India base contect number
2 nos quantity