This video saved me a ton of time and frustration. I hooked the illumination circuit to an aftermarket JVC stereo. That was a bad idea. The dash light dimmer did not dim the radio lights, so it obviously wasn't right. Now the illumination circuit is disconnected from the radio and it looks just the same at night. Hopefully that will solve my problem. After replacing the fuse, all lights work properly. Thanks for such an informative and time-saving video. Well done.
Patrick Murtagh Hot Diggity Dog that's great news. Thanks for checking out the video and sharing your comment and experience. So glad the video helped Patrick! Please Subscribe to the channel and turn on your UA-cam notifications that would be awesome thanks again 😀👍
Hey thats awesome...congrats on the new ride. Im glad it helped and thanks for checking out the video and sharing a comment. Subscribe to the channel if you're up to it !
Thanks for the tip. My 2008 Chevy Aveo5 hatch speedo and tach lights are out. I checked the fuse in the dash fuse box but that was OK. Morning I'll check under the hood. You MIGHT want to install the newer LED indicator fuses though. They make it SO much easier to isolate a blown fuse in the dark (worst time to lose your speedo light!).
Brenda Sews Awesome that’s great news Brenda...thank you so much for watching the video and we are so glad it helped. Please subscribe to the channel and turn on your UA-cam notifications that would be awesome thanks again 😎👍
Thanks for viewing and commenting. Those darn dash lights in cars are annoying when trying to figure them out haha. Subscribe to the channel if you're up to it thanks again!
Awesome and thanks for checking out the video and sharing your comment HavocFury. Glad the video helped. Please Subscribe to the channel that would be awesome thanks again!
Thank you for this. That saved me a lot of time and money. Still need to change a bulb that probably blew the fuse in the first place, but easy enough. Thank you.
Kit Wayne Thanks for watching, we appreciate you sharing your comment & experience. Keep us posted on your project, let us know if you have any questions. Please subscribe to the channel and turn on your UA-cam notification Bell 🛎 that would be awesome thanks again! 😎👍🔧🔩
duuddeeee thank you soo much my 2009 chevy spark got the same problem and i was confused cuz I didnt knew about those fuses connected to interior light
ronnie whitmore Awesome Awesome 😁 That’s great news! We appreciate you taking the time to watch & share your experience! Let us know if you have any additional questions along the way we are here to help! Please subscribe to the channel and turn on your UA-cam notification Bell 🛎 that would be awesome thanks again! 😎👍🔧🔩
Paul Sparrow What’s up Paul, thanks for watching. UA-cam Rocks! 😀 We are happy to hear the video helped. Let us know if you have any questions. Please subscribe to the channel and turn on your UA-cam notification Bell 🛎 that would be awesome thanks again! 😎👍🔧🔩
Your video was very helpful my tail lights were not working i follow your video i came right my lights working now only reverse light but i suspect reverse switch
I'm going to check the park fuse on my 90 300zx. My instrument lights, high beams, and 2 lower brake lights are out. The 3rd brake, park lights, 4 ways and turn signals are working. Could the hi/low and turn lever be tied to the intrument lights even though the instrument and light switch are on a seperate pod. The new turn signal switch lever is over $200. Thanks for any help.
Inn Deep Thanks for watching & sharing your comment! Let’s get this figured out! It’s very possible that your issues are tied to the Park/Lamp. We also recommend checking every single fuse & verifying that all fuses are in good operating condition. It’s also important to verify that you have spare fuses positioned in the spare fuse slots! Reference the diagram & verify that a fuse is positioned in every single slot that the diagram shows a fuse to be. Let’s start there! Keep us posted! Please subscribe to the channel and turn on your UA-cam notification Bell 🛎 that would be awesome thanks again! 😎👍🔧🔩
I'm going to check my fuses tomorrow. Hopefully that's my problem too. I pulled the old dash out of my 92 Miata but I kept all the same wires from the old one, when I hooked everything up my gauges wouldn't light up and the gas gauge doesn't seem to go down when I turn the car off. I haven't checked the tail light. The interior lights also don't light up but I don't think they did before
I just came across your video & I went outside & turned on my lights & I have no tail lights on my right side, sure enough I check the fuse & it's blown!! I don't want to drive right now cuz it's dark & I'm more worried than ever to drive now with no lights on my right side & not having a clue how fast I'm going so I'm praying that in the light of day tomorrow when I replace that fuse I'll not only have right hand side tail lights but that my dash will light back up too!! I'm driving a 2005 Dodge Stratus Coupe SXT by the way.
Good morning & welcome to the DIY Raptor Club. We appreciate you reaching out to us Robyn. Keep us posted on your project. Let us know if that new fuse gets you back up and running. 😎👍🔧🔩
@@DIYwithMichaelBorders well I'm not sure yet! I put the fuse in, turned on the lights to see & the damn thing blew again right away! I did just have to get the wiring on that light rebuilt a few months ago so that could be my problem. I'm taking the car back to them on Wednesday. Who knows how long that light hasn't been working! At first I kept blowing the fuse for my brake lights almost ever time I drove, carried a whole box of fuses with me at all times! The wrong bulb had been put in last year & burnt the connection where the build got screwed in. Sorry this is all jumbled but it's late & I can hardly keep my eyes open. Anyway I'll let you know! Thanks again for the video!
@@robynharkey5865 Thanks for the reply Robyn. Check the underside of the fuse box. Look at what amp fuse the light is requiring. If it’s requiring a 20amp fuse & the shop accidentally put in a 10amp fuse, it will blow every time. 😎👍🔧🔩
@@DIYwithMichaelBorders well you were right!!! The fuse was blown on my right tail light because when they replaced the wiring on that side when they put the light back in place a wire had been bent & over time got pinched causing it to blow the fuse which also took out my lights on my instrument panel. Now that they have unpinched the wiring & replaced my fuse I have all tail lights working & I will now be able to see how fast I'm going when I drive at night, my instrument panel lights do go off the same fuse as my right tail light. Thank you so much! If I had not found your video I would not have known my tail light was out on that side & that the 2 were working off the same fuse!
@@robynharkey5865 Thanks for the update & that’s great to hear Robyn. We really appreciate you taking the time to share this update. Sounds like you’re back up and running. We are always here to help answer questions. Enjoy your day. 😎👍🔧🔩
Thanks for checking out the video Ty Boyd! Whats the update...Have you checked the Pk/Lmp fuse yet? In most cases, its the fuse however if your fuse is still good, we need to look deeper into the electrical system. There might be a short somewhere. I recommend removing the tail lights and checking to see if you see any loose wires...usually never the case however we can't rule it out...In addition, its possible that the splice kit/box may beginning to fail...again less likely than a blown fuse! Keep me posted! Please Subscribe to the channel and turn on your UA-cam notifications that would be sweet! Thanks again Ty Boyd!
T.J. Ash Thanks for watching & you are very welcome! We are happy to hear the video helped & you are good to go! Let us know if you have any questions! Please subscribe to the channel and turn on your UA-cam notification Bell 🛎 that would be awesome thanks again! 😎👍🔧🔩
Kevin Cervantes Thanks for watching & you are very welcome Kevin. We really enjoy making these helpful videos for our fellow DIY’ers. 😀 Please subscribe to the channel and turn on your UA-cam notification Bell 🛎 that would be awesome thanks again! 😎👍🔧🔩
I have the same 2007 Chevy Aveo, but my problem go a lil far, my dash wasnt working at all, speed, RPMs, ODO, same with the 1st speed of my whipers, my tail lights and my windows. I open the fuse box inside, next to my dash and found the burned fuse, everything started working but the problem now is that just works if my front lights are ON, what can be causing the problem?? Thanks
Frank David Thanks for checking out the video and sharing your experience Frank...let’s get this figured out! There is a fuse labeled ( Illum Lamp ). Let’s take a look at this fuse. Your light switch is what closes the electrical circuits for your lighting system & this fuse must have power at all times! If fuse is failed, you will experience symptoms as you mentioned. Keep us posted! Please subscribe to the channel and turn on your UA-cam notifications that would be awesome thanks again Frank! 😎👍🔧🔩
My 2008 acadia has gauge problems. All the gauges work but back lights on the gas, temp, and battery gauges DO NOT light up. The speed and tach gauges are still back lit. Any suggestions ?????? All my lights work all the way around the vehicle . Thanks !
Thanks for watching & welcome to the DIY Raptor Club. It’s very possible that you have a lightbulb burnt out. Although we have not changed the internal instrument lightbulbs on an Acadia, we have a on Toyotas. Below is a link to a video that shows us replacing the internal instrument lightbulb that burnt out. ua-cam.com/video/Q8MDOZg1hZE/v-deo.html 😎👍🔧🔩
Jackson Hadley Thanks for watching & sharing your question. The fuse box shown in this video is inside the engine compartment as shown. You will need to go inside vehicle on drivers side. On the lower left side by brake pedal, you will see an access door to an additional fuse compartment. On the back of the door will be the fuse assortment diagram. Try & locate a fuse referencing the pressure indicator. Keep us posted. Please subscribe to the channel and turn on your UA-cam notification Bell 🛎 that would be awesome thanks again! 😎👍🔧🔩
Supa Gaming ™ Thanks for checking out the video and sharing your experience Supa Gaming! Unfortunately this is a common issue in Honda's. It's very possible that your "Drivers Multiplex Computer has faulted...under dash near hood latch release lever. You will see a small white box. This is the part that has possibly failed. Keep me posted. Please Subscribe to the channel and turn on your UA-cam notifications that would be awesome thanks again 😎👍
Thanks for watching & sharing this. Unfortunately not at the moment. Keep us posted on your project. Us fellow DIY’ers need to stick together! Enjoy your day. 😎👍🔧🔩
Chevy 2006 cobalt. Happened to me yesterday. Dash lights dont light up amd tail lights out. Im gonna check fuses. And its both tail lights out. Why?????
Polarwyze85 What’s up Polarwyze85... Thanks for checking out the video and sharing your experience...this is a pretty friendly repair! In most cases, the group of lights are wired on the same circuit...keep us posted on your progress! Please subscribe to the channel and turn on your UA-cam notifications that would be awesome thanks again 😎👍
Kristen Supple Thanks for watching & sharing your question. Great question & you’re spot on. In your explained scenario, it’s almost always as simple as a fuse. We recommend taking a few minutes to check your fuse box & replace the fuse as necessary. Keep us posted! Please subscribe to the channel and turn on your UA-cam notification Bell 🛎 that would be awesome thanks again! 😎👍🔧🔩
yeah. theres some fuses that are missing. like the grey box looking fuses. do you know if those have anything to do with lights? sorry im no car person lol
Its rare that the actual light burns out which leads me to the 101 splice kit. Recently I spoke to an individual that had a shop look at his car dealing with same issue and found that one of the wires within the 101 Splice kit had rusted/burned to a point that was not allowing it to allow electric current to pass through it. 101 Splice kits can get pretty expensive when having shop or dealership repair them.
Hey, my fuses are ok both in that fuse box and the cluster in the car. Front lights work fine, but might time tail lights don’t. Break lights work though. This started when I replaced the front drivers H/L bulb. Can you help?
Evan White Thanks for watching Evan! Let’s get this figured out! It’s possible that a fuse has blown. We recommend checking all fuses that reference lights. Next check all wires feeding into fuse box. Look for any signs of stress...melted wires, frayed wires... Let’s start there! Keep us posted! Please subscribe to the channel and turn on your UA-cam notification Bell that would be awesome thanks again! 😎👍🔧🔩
DIY With Michael Borders fuses are ok. Checked the fuse mentioned in the video and the cluster fuse. I will now check the wires I guess. Forgot to mention that the tail lights worked ever other day in the beginning, but now not at all.
Evan White Thanks for the reply! Lights working intermittently is almost always due to a loose ground connection. At this point it’s important to check all wire connection points as well. You may want to remove the new bulb you put into the front drivers h/l. See if this alters the activity you are experiencing. It things go back to normal...we need the address the front drivers h/l wiring, harness, and get a different bulb.
Its rare that the actual light burns out which leads me to the 101 splice kit. Recently I spoke to an individual that had a shop look at his car dealing with same issue and found that one of the wires within the 101 Splice kit had rusted/burned to a point that was not allowing it to allow electric current to pass through it. 101 Splice kits can get pretty expensive when having shop or dealership repair them. Keep me posted
my celica toyota have no dash ligths at all and no aircon even when starting it totally black out...i called my electricians twice and fix f9r an hour but after rested an hour still black out...what happened??lossen wires??i dont know...
Thanks for checking out the video. It can be a couple different things. Its possible that the wires have been harmed...such as over heating/melted. Take a few minutes and inspect your wiring under the hood near the firewall as well as the wiring inside the car near your foot pedals. Its possible that your "Ground Wire" has become loose which leads to the intermittent operation of the lights. Check the fuse box...Verify that you have the correct fuse in the slot for the lights...example: if it calls for a 10 fuse...make sure you insert a 10 and not a 15 or 20. I have attached a video that shows me replacing some bulbs behind the instrument panel...it might help you. Keep me posted Please SUBSCRIBE to the channel that would be awesome thanks again! ua-cam.com/video/Q8MDOZg1hZE/v-deo.html
my Toyota Camry speedometer lights only works in its half left side. Everything else works fine in my dashboard. Do you think its a bulb or fuse issue?
Thanks for checking out the video and sharing your comment and experience. Its definitely possible that you have a bulb that is burnt out. I experienced the exact same issue with half the lights working and the other half not working. I have attached a video that shows me replacing a bulb on my Toyota. Keep me posted. Please SUBSCRIBE to the channel that would be awesome thanks again! ua-cam.com/video/Q8MDOZg1hZE/v-deo.html
i checked all the fuses, every one is good. how do i know if the bulb behind the dash board is still good? if its bad how do i change it without calling mechanic.
Grace Thompson Thanks for checking out the video Grace. It should be the same fuse. Keep me posted on your repair. Please subscribe to the channel and turn on your UA-cam notifications that would be awesome thanks again Grace! 😎👍
I've checked the hatchback vs the sedan fuses boxes and the hatchback doesn't have that fuse by that name....so I'm wondering if it's just labeled differently in the hatchback?
Grace Thompson After opening you Door, you will notice a small plastic access door on the side of your dash...left of Steering wheel. Inside are additional fuses. Locate the (Cluster) fuse and see if that has blown.
Sourav Halder Thanks for watching & sharing your experience. We recommend checking all fuses & verifying all electrical connection points are secured. Keep us posted. Please subscribe to the channel and turn on your UA-cam notification Bell 🛎 that would be awesome thanks again! 😎👍🔧🔩
Did this on my g5 that had the same problem except the fuse kept blowing once i started the car and before I started it the gauge lights flashed on and off
Good morning and thanks for reaching out to us. It sounds like you have a short or a loose connection somewhere along your electrical wiring. Do a quick inspection of your wiring that feeds in and out of fuse box and ensure you do not see any loose connections or signs of stress such as melted, frayed, or crimped wiring. 😎👍🔧🔩
Patricia Toth Awesome! Thanks for checking out the video and sharing your update. Please Subscribe to the channel that would be awesome. Thanks again Patricia 😀👍
+Jocelyn Riedel No...have you tried all the tricks shown in this video? Also read all the comments below because there are a few other options to explore. Thanks for viewing. Subscribe to the channel thanks!!
what if that fuse is good. is there another fuse that will stop it from working? my tail light works now but the dashboard still out. someone told me it may be the bulb in the dashboard. i dont know what im doing and trying to fix on my own without expense of mechanic. can you help me? 2009 chevy aveo. thanks in advance
Down by where the pedals are inside car sitting in drivers seat, you will notice a fuse cover on lower left side. On the back of that plastic cover is a diagram of the fuse set-up. I don't have the vehicle in front of me but try to locate fuse that references radio/stereo/light....this may be you're problem. Keep me posted. Subscribe to the channel if you're up to it thanks again!
Hi my dash light went out on me , the speed thermometer and gas gauge isn’t working at all so I can’t see if I’m low on gas or how fast I’m going . Can you give me any advice if it’s related to the dash lights being out ? Thanks a lot 👍🏻
Thanks for watching & this should be a friendly DIY project. We recommend taking a look at the internal portion of your fuse box cap & locating where your instrument cluster fuses & fuel gauge fuses are. Check those & replace any & all fuses that have burned out. 😎👍🔧🔩
Ethan Smith What’s up Ethan, thanks for watching & we hope the video helped. It should. Keep us posted. We really enjoy making these helpful videos for our fellow DIY’ers. Many more helpful videos to come! 😀 Let us know if you have any questions. Please subscribe to the channel and turn on your UA-cam notification Bell 🛎 that would be awesome thanks again! 😎👍🔧🔩
What if i turn on only the park lights, and only the gauge light is not working? but the parklight/tail lights is working while the park light is switched on? Buf if i turn on the fog lights, the gauge light will work. Usually if i turn on my parklight, the gauge light is on.
joshua busa Thanks for watching & sharing your experience joshua. Have you verified all fuses & electrical wiring are in good clean working condition? Keep us posted! Please subscribe to the channel and turn on your UA-cam notification Bell 🛎 that would be awesome thanks again! 😎👍🔧🔩
manu gruni What’s up manu gruni... Thanks for checking out the video and sharing your comment. You can definitely use the spare fuse. It is important that you use the same size fuse...ex: don’t replace a 10amp fuse with a 5amp fuse...not good! Also after you use the spare, its also a good idea to refill the spare fuses so you have them handy when you’re on the road away from home. Keep me posted on your repair! Please subscribe to the channel and turn on your UA-cam notifications that would be awesome thanks again 😎👍
I got one for you man my lights on dash wont work neither does my tailights only when I hit the breaks and the hazzards but when I turn on my lights nothing comes on
D21 Thanks for watching, have you already replaced the fuse shown in this video? If yes, lets direct our attention to the next possible fuse! Down by where the pedals are inside car sitting in drivers seat, you will notice a fuse cover on lower left side. On the back of that plastic cover is a diagram of the fuse set-up. I don’t have the vehicle in front of me but try to locate fuse that references radio/stereo/light....this may be your problem fuse. Keep me posted. Please subscribe to the channel and turn on your UA-cam notification Bell 🛎 that would be awesome thanks again! 😎👍🔧🔩
User Thanks for checking out the video. This should work! There wasn't much electrical change from 07-09...just slightly different locations as you mentioned. Please Subscribe to the channel that would be awesome thanks again 😀👍
Just bought new fuses from O'Reilly's and replaced both the pklp rh and the pklp lh but dash still won't light up.. could it be the lightbulb or other fuses? Something else I'm missing?
User Bummer...double check the electrical connection point on the bulb. Also check to see if the bulb needs to be replaced. Also keep an eye open for any possible burnt or frayed wires...any signed if this might help solve the problem! 😀
I don't understand - don't the tail lights work at the start of video? You showed they turn on when you depress the brakes...isn't that how they are supposed to behave?
0pt618 Thanks for checking out the video. When this fuse blows...you won't have any Tail Lights after turning on you headlight switch. The only time your tail lights will illuminate is when you press the brakes. Sorry my video doesn't really mention it in that order. Subscribe to the channel that would be awesome thanks again 😀👍
Anthony, thanks for checking out the video. I did some research on your vehicle and I have found that many people have run into your very experience. Looks like there was a recall on the instrument cluster for this vehicle years ago. You vehicle is covered if still below 70,000 miles and less than 7 years old. I have found that most people experienced this issue around 125,000 miles. There are other Escalade owners that have run into just one side failing while the middle and other side still work. There is usually 1-3 electrical connection points that clip into the back of the entire instrument cluster...one may have come loose...not likely though because if its just your fuel not working and your engine temp gauge is...then its connected. I recommend calling the dealer and explain the issue...get a second opinion. The cool thing is there are a few UA-cam videos that show changing that instrument cluster. It might be something you can do at home. Keep me posted. Please Subscribe to the channel that would be awesome!
Hiya folks I've got a Skoda superb elegance 2012 model and the clock is half lit up but flickers now and again and by the way the speedo clock is factory fitted with leds any idea folks? Is it that fuse in the video I need to check?
Nasar Khan Thanks for checking out the video! From what you explain...my thought is that it's a short in the ground! Double check all wires and connections. If it's flickering...your fuse is still good! Keep me posted! Subscribe to the channel that would be awesome 😀👍
DIY With Michael Borders the clutch and flywheel was changed recently then this flickering happened so from what I gather the earth (ground) on car battery has a poor connection?
Horn was working but stopped working after 100 amp fuse blew on the battery terminal. I replaced it. I also replaced the horn fuse but nothing. Any idea?
Thanks for watching & welcome to the DIY Raptor Club. Is it the original radio or an aftermarket radio? You may have a loose connection making the radio intermittent.
Hey, thanks for the video. I have a Hyundai Elantra 2001. There is no fuse called pk and I have changed the tail -RH (Cause its the right light and the dashboard not working), in fact I changed both tail fuses and nothing worked. Please help
thanks for viewing and commenting. I did some quick research and have found that it most likely is your ( Side Maker BULB ). The reason for all the outages is due to the fact that it all runs on a single circuit. This means once one item on the circuit goes bad "Or burns out"...it turns off all additional items on circuit. Change the marker bulb and see if that fixes the problem. Keep me updated. Subscribe to the channel if you're up to it. Thanks again!
+Michael Borders so I just found out its the fuse, whenever I change it with another 10 it blows immediately so I put a 30 and it's working perfectly. obviously I know this is ill-advised bt at least I know the problem when I take it to the shop. Thanks so much man
Adam Mauch Thanks for watching Adam, let’s get this figured out together! Down by where the pedals are inside car sitting in drivers seat, you will notice a fuse cover on lower left side. On the back of that plastic cover is a diagram of the fuse set-up. I don’t have the vehicle in front of me but try to locate fuse that references radio/stereo/light....this may be your problem fuse. Keep me posted. Please subscribe to the channel and turn on your UA-cam notification Bell 🛎 that would be awesome thanks again Adam! 😎👍🔧🔩
hi/hello i got kia cerato 2006 my dash lights don't work but its works when i reverse and i checked all fuse any idea what this issue can be thanks for any help.
Hey there thanks for checking out the video. I did a little research on this vehicle. 1. Several Kia Cerato owners have found the problem to be a lose connection behind the instrument cluster. This will require you to remove the cluster and check connections. You may even need to readjust the tension on the connection cable. 2. Previous owners have experienced a lose or acting up headlight switch which is on the same circuit and may alter the workings of other bulbs. 3. In 2006, there was a Manufacture Recall on this issue and was announced that all repairs by a certain date will be covered however that date is expired.....maybe the previous owner had it replaced.....any records of if they did or not???? Keep me posted....Subscribe to the channel that would be AWESOME :-)
momen kareem Thanks for watching & sharing your experience. The most common cause of this is an electrical short somewhere along the wiring. We recommend doing a thorough inspection of the electrical wires that feed out of your fuse box & following it as far as you can. Also check inside the vehicle near the brake pedal & make sure all wires & electrical connection points are properly secured. Let’s start there! Keep us posted! Please subscribe to the channel and turn on your UA-cam notification Bell 🛎 that would be awesome thanks again! 😎👍🔧🔩
Great video. I hope you can help me. I bought an audi a3 2008 and half of the miles per hour part of it it keeps blinking also from time to time the gas and oil lights in the middle flash. Could it be a fuse? Thank you
Thanks for checking out the video and sharing your experience. Since the lights are blinking at different times rather than completely not working leads to a definite short in the wiring system. This can be as simple as a loose ground wire. Do a thorough inspection of all your wires that lead to the under side of your dash. Verify that all wires are connected. Check that the fuses are all in and secure in all the fuse slots. Also check the larger wire harness that runs from the fuse box to other wires throughout the dash. Lots to look at, so sorry !! Another option it can be...however "In most cases" unlikely because your car is running fine...your Alternator may be starting to perform intermittently...which can cause the flickering of your dash lights. Like I said though, since your car is running good, this is most likely not the issue....but not to be completely ruled out haha! Keep me posted. Please Subscribe to the channel and turn on your UA-cam notifications that would be awesome thanks again!
Luis Suarez Thanks for watching Luis! We found a few good options on Ebay for your car. We recommend taking a look at Ebay & typing in 2004 G35 Speedometer! A few good options will come up. Keep us posted on your project! Please subscribe to the channel and turn on your UA-cam notification Bell 🛎 that would be awesome thanks again! 😎👍🔧🔩
Coyote Trapper 85 Thanks for watching, we recommend disconnecting your negative terminal from your battery & inspecting all wires feeding into & behind paneling leading to your instrument cluster. You may have a loose connection which is leading to a short...which is then causing the wires to overheat and/or arc which will lead to your symptoms. Locating a loose connection point and then re-securing it & replacing damaged wires will hopefully fix your issue. Keep us posted. Please subscribe to the channel and turn on your UA-cam notification Bell 🛎 that would be awesome thanks again! 😎👍🔧🔩
DIY With Michael Borders ok so it will come on then the top left hand side of the back of the panel gets really hot then the cluster stops working checked all the wires there good and the wires aren’t getting hit at all just the back of the cluster gets really hot
Coyote Trapper 85 Thanks for the update. Have you removed the entire Cluster for inspection? By chance have you pinpointed any specific wiring or connection leads that are hotter than others that feed into Cluster? If you have access to replacing all light bulbs in rear Cluster, new bulbs may help eliminate increased heat...It’s uncommon however possible. Keep us posted! 😎👍🔧🔩
You would need to use a volt meter to check electrical current...it's a bunch of wires that feed into a white harness that separates wires. It's located underneath the fuse box. Did you check the PK LMP fuse that I mention in video already!
My daughter just bought a 2007 chevy aveo ls for her first car and the horn is not working . I checked the fuses and they are ok. I am not sure if there is a relay for me to check next. Trying to fix ourselves and hopefully this is all that is wrong.
Jennifer Tucker Thanks for watching. What’s your update? Have you been able to get your project solved? Keep us posted. Please subscribe to the channel and turn on your UA-cam notification Bell 🛎 that would be awesome thanks again! 😎👍🔧🔩
Jennifer Tucker Thanks for the reply. Most relays/fuses will be inside engine as shown here. There is also a small access door on lower left corner inside drivers side front...left of pedals. Check & verify fuses are not blown. 😎👍🔧🔩
Luke Doraz Thanks for watching & sharing your question. We haven’t worked on that vehicle in the near past & recommend contacting your local dealership. They will ask for your Vin # and be able to pull up the exact diagram and location of your fuse. We hope this helps. Please subscribe to the channel and turn on your UA-cam notification Bell 🛎 that would be awesome thanks again! 😎👍🔧🔩
Jelly Thomas18 Thanks for watching & hopefully this video helped as you mentioned you have same car. 😀 Please subscribe to the channel and turn on your UA-cam notification Bell 🛎 that would be awesome thanks again! 😀👍🔧🔩
Alan Quarrie What’s up Alan, thanks for watching. You are very welcome. Us fellow DIY’ers need to stick together, many more helpful videos to come! 😀 Please subscribe to the channel and Ring your UA-cam Bell 🛎 that would be awesome thanks again! 😎👍🔧🔩
+Michael Borders I figured it out I made a comment on another video describing how to fix it. But in my case my dash lights wouldn't work my brake lights wouldn't work and neither would my license plate lights and for most people it is the instrument illumination fuse but in my case and most ford cases it is the main light switch fuse
Good morning, just poured a ☕️ and am sitting down to answer any and all questions for the DIY community. You are welcome, we are honored you took the time to share this. Let us know if you have any questions and hey if you’re interested, join our DIY ecosystem and help us grow an exclusive group of DIYers. toolboxtoken.com Reach out to us any time! 🧰
Kevin Grove Thanks for checking out the video. This can definitely be an annoying issue. In short...as you know, Fuses are specifically designed to save the electrical system and its wires. Most of the time you run into a fuse blowing on a consistent basis...you may have a short. (Possibly exposed wires that are coming into contact with other wires). I would first disconnect your battery and then begin to look for any frayed, loose, burnt, or damaged wires near your electric box under the hood as well as near your tail lights. If you come across any signs of damaged wires...you'll need to address them. In some cases, electrical tape can be used to secure any open wires however my recommendation is to get a second opinion from a MX shop due to the possible severity of a bad electrical connection. Keep me posted...we can get this figured out together! Please Subscribe to the channel that would be awesome thanks again 😎👍
Ok so I checked the wires and couldn't see anything, unfortunately my large head could get that far under the fuse box, but from feeling around I didn't feel anything loose or open. I just put another fuse in and it has not blown out yet. Thanks again and I will keep you updated later tonight if it happens again (hopefully it doesn't)
Kevin Grove Very cool. That's good news! Also you might want to check the connection points that your fuse fits into and clean out any debris/corrosion....Make sure your battery is disconnected....if you have an air compressor, you can try to use the air hose nozzle to remove any/all dirt, lint, leaves...
dice portz Thanks for watching & we hope the video helped. We appreciate you reaching out to us. We really enjoy making these helpful videos for our fellow DIY’ers. Many more helpful videos to come! 😀 Let us know if you have any questions. Please subscribe to the channel and turn on your UA-cam notification Bell 🛎 that would be awesome thanks again! 😎👍🔧🔩
Dcdatruth85 Thanks for watching & sharing your comment. Keep us posted on your DIY project & if replacing the light solves your issue. Please subscribe to the channel and turn on your UA-cam notification Bell 🛎 that would be awesome thanks again! 😎👍🔧🔩
Thanks for watching & welcome to the DIY Raptor Club. Do you see any loose wires or damaged wires...crimped, melted, exposed & rusted wires near the fuse box? Keep us posted. Hope all is well. 😎👍🔧🔩
Thanks for watching & welcome to the DIY Raptor Club. Examples can be... • Electrical overload • Overheat • Electrical short • Old corroded fuse • Wrong fuse installed • Having over 10,000 hours of accumulated time on fuse Let us know what you find. We are curious to see what caused yours to blow. Enjoy your night! 😎👍🔧🔩
OfficialAdvanced You are very welcome & thanks for watching! Keep us posted with any questions you may have. Please subscribe to the channel and turn on your UA-cam notification Bell 🛎 that would be awesome thanks again! 😎👍🔧🔩
Bayleigh N Owen Thanks for checking out the video. Hope it helped. Please Subscribe to the channel and turn on your youtube notifications that would be awesome thanks again 😀👍
Justin Ramdass What’s up Justin, we appreciate you reaching out to us. Have you checked all fuses inside the engine compartment as well as down below to the left of your brake pedal. Keep us posted. Us fellow DIY’ers need to stick together! 😎👍🔧🔩
@@DIYwithMichaelBorders I checked the fuses inside and out all is good and another problem the reverse light isn't comming on as I changed the bulbs As well as the temperature gauge it all happened the same day
Theres an issue for me. There was a 20A fuse where the PK/LP RH 10A fuse should be, and Im a little worried that there is some electrics fried as nothing is turning on and the fuse isnt melted
Wingstar Thanks for watching & we hope the video helped. If your vehicle is a 2007, we recommend removing that 20amp & installing the correct 10amp fuse. If your vehicle is not a 2007, it’s possible that your system uses a 20amp. Check the inner side of your cap & see what it says....10amp or 20amp...??? We really enjoy making these helpful videos for our fellow DIY’ers. Many more helpful videos to come! 😀 Let us know if you have any questions. Please subscribe to the channel and turn on your UA-cam notification Bell 🛎 that would be awesome thanks again. 😎👍🔧🔩
@@DIYwithMichaelBorders I have already checked the underside of the fuse box lid, it does say that it needs a 10 amp fuse. Mine is a 2008 and I am fairly sure that it is the same inside and out. Thanks for the reply 👍👍
Thanks for watching & good morning, we are drinking our morning coffee answering any and all questions for the DIY community. We recommend performing a friendly reset. To do this, disconnect the black negative cable from your battery and leave disconnected for a minimum of 30 minutes. This will allow your onboard computer to reset. After 30 minutes, re-secure black negative cable to your battery and start engine. Keep us posted. 😎👍
@@kboss0604 Good morning, that’s what we’re here for. We DIYers need to stick together! Have you checked all fuses including the fuses inside vehicle down near your pedals on left side?
@@kboss0604 Thanks for the reply. We recommend looking at the diagram on inner cap at checking all fuses related to lamp, lights, & instrument cluster/panel.
study times Thanks for checking out the video! Whats the update...Have you checked the Pk/Lmp fuse yet? In most cases, its the fuse however if your fuse is still good, we need to look deeper into the electrical system. There might be a short somewhere. I recommend removing the tail lights and checking to see if you see any loose wires...usually never the case however we can't rule it out...In addition, its possible that the splice kit/box may beginning to fail...again less likely than a blown fuse! Keep me posted! Please Subscribe to the channel and turn on your UA-cam notification Bell 🛎 that would be sweet! Thanks again!
Seth Burkholder Thanks for watching Seth! Let’s get this figured out! Have you located the fuse shown in this video & replaced it? Keep us posted! Please subscribe to the channel and turn on your UA-cam notification Bell 🛎 that would be awesome thanks again! 😎👍🔧🔩
Thanks for watching, we appreciate you sharing this. Bummer, do you see any signs of melted wiring or electrical connections? Please let us know if you have any questions.
This video saved me a ton of time and frustration. I hooked the illumination circuit to an aftermarket JVC stereo. That was a bad idea. The dash light dimmer did not dim the radio lights, so it obviously wasn't right. Now the illumination circuit is disconnected from the radio and it looks just the same at night. Hopefully that will solve my problem. After replacing the fuse, all lights work properly. Thanks for such an informative and time-saving video. Well done.
Patrick Murtagh Hot Diggity Dog that's great news. Thanks for checking out the video and sharing your comment and experience. So glad the video helped Patrick! Please Subscribe to the channel and turn on your UA-cam notifications that would be awesome thanks again 😀👍
just bought a car from the auction and noticed this problem,, Thank you for making my day*
Hey thats awesome...congrats on the new ride. Im glad it helped and thanks for checking out the video and sharing a comment. Subscribe to the channel if you're up to it !
@@DIYwithMichaelBorders @
@@farhantariq4478
Thanks for watching.
Thanks for the tip. My 2008 Chevy Aveo5 hatch speedo and tach lights are out. I checked the fuse in the dash fuse box but that was OK. Morning I'll check under the hood.
You MIGHT want to install the newer LED indicator fuses though. They make it SO much easier to isolate a blown fuse in the dark (worst time to lose your speedo light!).
Lt P
Thanks for watching & sharing your thoughts. Keep us posted on your project.
😎👍🔧🔩
Thank you, so happy it was just a fuse and not a wiring issue! Fixed my problem in under a minute!
Brenda Sews Awesome that’s great news Brenda...thank you so much for watching the video and we are so glad it helped. Please subscribe to the channel and turn on your UA-cam notifications that would be awesome thanks again 😎👍
THANK YOU! I was so confused why my dash lights and back left light wasn't working so thank you!
Thanks for viewing and commenting. Those darn dash lights in cars are annoying when trying to figure them out haha. Subscribe to the channel if you're up to it thanks again!
thanks for the video, I have a different model Chevy, but everything is about the same. Everything works now.
Awesome and thanks for checking out the video and sharing your comment HavocFury. Glad the video helped. Please Subscribe to the channel that would be awesome thanks again!
Thank you for your help!! After your video I was able to fix the problem on my own. We're back in business!! :)
Leila Rollins Hey very cool, I'm glad it helped. Thanks for sharing a comment. Subscribe to the channel if you're up to it. That would be awesome 😀👍
Genuinely, thank you! I was able to do this on my own. 👍🏼
Thank you for this. That saved me a lot of time and money. Still need to change a bulb that probably blew the fuse in the first place, but easy enough. Thank you.
Kit Wayne
Thanks for watching, we appreciate you sharing your comment & experience. Keep us posted on your project, let us know if you have any questions.
Please subscribe to the channel and turn on your UA-cam notification Bell 🛎 that would be awesome thanks again! 😎👍🔧🔩
duuddeeee thank you soo much my 2009 chevy spark got the same problem and i was confused cuz I didnt knew about those fuses connected to interior light
"that fuse is blown, just as we thought", and just happen to have a pack right here. What are the odds 😊
ronnie whitmore
Awesome Awesome 😁
That’s great news! We appreciate you taking the time to watch & share your experience!
Let us know if you have any additional questions along the way we are here to help!
Please subscribe to the channel and turn on your UA-cam notification Bell 🛎 that would be awesome thanks again! 😎👍🔧🔩
Thank you so much. I was trying to help a buddy out but he’s being stubborn 😅
Good morning ☕️ you are welcome. You’re a good friend for helping out.
😎👍
Your a legend :) my 04 Nissan n16 almera seems to run its dash lights on the tail light fuse also, thankyou very much for your help
Paul Sparrow
What’s up Paul, thanks for watching. UA-cam Rocks! 😀 We are happy to hear the video helped.
Let us know if you have any questions. Please subscribe to the channel and turn on your UA-cam notification Bell 🛎 that would be awesome thanks again!
😎👍🔧🔩
@@DIYwithMichaelBorders who would have known the tail lamps and the dash lights were on the same fuse :o thanks again for your video
Paul Sparrow
😎👍🔧🔩
Your video was very helpful my tail lights were not working i follow your video i came right my lights working now only reverse light but i suspect reverse switch
I forgot about those fuses in engine bay...thanks to this vid found the issues
Awesome, you are welcome. Thank you! 😎👍
Thank you. You rock
I'm going to check the park fuse on my 90 300zx. My instrument lights, high beams, and 2 lower brake lights are out. The 3rd brake, park lights, 4 ways and turn signals are working. Could the hi/low and turn lever be tied to the intrument lights even though the instrument and light switch are on a seperate pod. The new turn signal switch lever is over $200. Thanks for any help.
Inn Deep
Thanks for watching & sharing your comment! Let’s get this figured out!
It’s very possible that your issues are tied to the Park/Lamp.
We also recommend checking every single fuse & verifying that all fuses are in good operating condition. It’s also important to verify that you have spare fuses positioned in the spare fuse slots!
Reference the diagram & verify that a fuse is positioned in every single slot that the diagram shows a fuse to be.
Let’s start there! Keep us posted! Please subscribe to the channel and turn on your UA-cam notification Bell 🛎 that would be awesome thanks again! 😎👍🔧🔩
Hey Dude, THANKS a lot. your video did help me get my dash lights back on..
Luis marchan Sorry for the delay thanks for checking out the video. Subscribe to the channel that would be awesome thanks again!
I'm going to check my fuses tomorrow. Hopefully that's my problem too. I pulled the old dash out of my 92 Miata but I kept all the same wires from the old one, when I hooked everything up my gauges wouldn't light up and the gas gauge doesn't seem to go down when I turn the car off. I haven't checked the tail light. The interior lights also don't light up but I don't think they did before
Thanks for checking out the video. Keep me posted on the outcome after fuse replacement 😀👍
Michael Borders
I traced it back on the wiring diagram to the TNS relay so i ordered a new one and I'm waiting to see if that does it
+Austin LaHood thanks for the update. That's awesome! 😀👍
I just came across your video & I went outside & turned on my lights & I have no tail lights on my right side, sure enough I check the fuse & it's blown!! I don't want to drive right now cuz it's dark & I'm more worried than ever to drive now with no lights on my right side & not having a clue how fast I'm going so I'm praying that in the light of day tomorrow when I replace that fuse I'll not only have right hand side tail lights but that my dash will light back up too!! I'm driving a 2005 Dodge Stratus Coupe SXT by the way.
Good morning & welcome to the DIY Raptor Club. We appreciate you reaching out to us Robyn. Keep us posted on your project. Let us know if that new fuse gets you back up and running.
😎👍🔧🔩
@@DIYwithMichaelBorders well I'm not sure yet! I put the fuse in, turned on the lights to see & the damn thing blew again right away! I did just have to get the wiring on that light rebuilt a few months ago so that could be my problem. I'm taking the car back to them on Wednesday. Who knows how long that light hasn't been working! At first I kept blowing the fuse for my brake lights almost ever time I drove, carried a whole box of fuses with me at all times! The wrong bulb had been put in last year & burnt the connection where the build got screwed in. Sorry this is all jumbled but it's late & I can hardly keep my eyes open. Anyway I'll let you know! Thanks again for the video!
@@robynharkey5865
Thanks for the reply Robyn. Check the underside of the fuse box. Look at what amp fuse the light is requiring.
If it’s requiring a 20amp fuse & the shop accidentally put in a 10amp fuse, it will blow every time.
😎👍🔧🔩
@@DIYwithMichaelBorders well you were right!!! The fuse was blown on my right tail light because when they replaced the wiring on that side when they put the light back in place a wire had been bent & over time got pinched causing it to blow the fuse which also took out my lights on my instrument panel. Now that they have unpinched the wiring & replaced my fuse I have all tail lights working & I will now be able to see how fast I'm going when I drive at night, my instrument panel lights do go off the same fuse as my right tail light. Thank you so much! If I had not found your video I would not have known my tail light was out on that side & that the 2 were working off the same fuse!
@@robynharkey5865
Thanks for the update & that’s great to hear Robyn. We really appreciate you taking the time to share this update. Sounds like you’re back up and running. We are always here to help answer questions. Enjoy your day.
😎👍🔧🔩
I have a 05 Scion tC & im experiencing the same issue . My dash/gas/rpm lights aren't working
Thanks for checking out the video Ty Boyd! Whats the update...Have you checked the Pk/Lmp fuse yet? In most cases, its the fuse however if your fuse is still good, we need to look deeper into the electrical system. There might be a short somewhere. I recommend removing the tail lights and checking to see if you see any loose wires...usually never the case however we can't rule it out...In addition, its possible that the splice kit/box may beginning to fail...again less likely than a blown fuse! Keep me posted! Please Subscribe to the channel and turn on your UA-cam notifications that would be sweet! Thanks again Ty Boyd!
Thank you 😊 it worked whoo ohhhoo 🙆🏽♂️🙆🏽♂️🥳🥳
You are very welcome. We appreciate you sharing this, enjoy your week.
😎👍🔧🔩
my battery led light doesn't illuminate when i switch on the switch ( not start the car) , why is that & how can i fix it??
Fixed them. Thank you!
T.J. Ash
Thanks for watching & you are very welcome! We are happy to hear the video helped & you are good to go!
Let us know if you have any questions! Please subscribe to the channel and turn on your UA-cam notification Bell 🛎 that would be awesome thanks again!
😎👍🔧🔩
Thank you! 💯
Kevin Cervantes
Thanks for watching & you are very welcome Kevin. We really enjoy making these helpful videos for our fellow DIY’ers. 😀
Please subscribe to the channel and turn on your UA-cam notification Bell 🛎 that would be awesome thanks again!
😎👍🔧🔩
I have the same 2007 Chevy Aveo, but my problem go a lil far, my dash wasnt working at all, speed, RPMs, ODO, same with the 1st speed of my whipers, my tail lights and my windows. I open the fuse box inside, next to my dash and found the burned fuse, everything started working but the problem now is that just works if my front lights are ON, what can be causing the problem?? Thanks
Frank David Thanks for checking out the video and sharing your experience Frank...let’s get this figured out!
There is a fuse labeled ( Illum Lamp ). Let’s take a look at this fuse. Your light switch is what closes the electrical circuits for your lighting system & this fuse must have power at all times! If fuse is failed, you will experience symptoms as you mentioned. Keep us posted! Please subscribe to the channel and turn on your UA-cam notifications that would be awesome thanks again Frank! 😎👍🔧🔩
Frank David I’m having the same EXACT problem what did you do too fix yours?
My 2008 acadia has gauge problems. All the gauges work but back lights on the gas, temp, and battery gauges DO NOT light up. The speed and tach gauges are still back lit. Any suggestions ?????? All my lights work all the way around the vehicle . Thanks !
Thanks for watching & welcome to the DIY Raptor Club. It’s very possible that you have a lightbulb burnt out.
Although we have not changed the internal instrument lightbulbs on an Acadia, we have a on Toyotas. Below is a link to a video that shows us replacing the internal instrument lightbulb that burnt out.
ua-cam.com/video/Q8MDOZg1hZE/v-deo.html
😎👍🔧🔩
How to get the tire pressure indicator to turn on what fuse should check?
Jackson Hadley
Thanks for watching & sharing your question. The fuse box shown in this video is inside the engine compartment as shown.
You will need to go inside vehicle on drivers side. On the lower left side by brake pedal, you will see an access door to an additional fuse compartment.
On the back of the door will be the fuse assortment diagram. Try & locate a fuse referencing the pressure indicator.
Keep us posted. Please subscribe to the channel and turn on your UA-cam notification Bell 🛎 that would be awesome thanks again!
😎👍🔧🔩
Clean battery terminals too
Thanks for watching & we appreciate you sharing this. Any & all helpful info is much appreciated.
Hope all is well. 😎👍🔧🔩
Hey my honda doesn't have a pk option it's a honda civic coupe? What is it called on these?
Supa Gaming ™ Thanks for checking out the video and sharing your experience Supa Gaming! Unfortunately this is a common issue in Honda's. It's very possible that your "Drivers Multiplex Computer has faulted...under dash near hood latch release lever. You will see a small white box. This is the part that has possibly failed. Keep me posted. Please Subscribe to the channel and turn on your UA-cam notifications that would be awesome thanks again 😎👍
My chevy aveo, the gauge panel all are down. Do you have a video on how to fix it. Thanks
Thanks for watching & sharing this. Unfortunately not at the moment. Keep us posted on your project. Us fellow DIY’ers need to stick together!
Enjoy your day. 😎👍🔧🔩
Chevy 2006 cobalt. Happened to me yesterday. Dash lights dont light up amd tail lights out. Im gonna check fuses. And its both tail lights out. Why?????
Polarwyze85 What’s up Polarwyze85... Thanks for checking out the video and sharing your experience...this is a pretty friendly repair! In most cases, the group of lights are wired on the same circuit...keep us posted on your progress! Please subscribe to the channel and turn on your UA-cam notifications that would be awesome thanks again 😎👍
If the speedometer and tachometer are working and just the light is out, that is most likely a fuse, right?
Kristen Supple
Thanks for watching & sharing your question. Great question & you’re spot on. In your explained scenario, it’s almost always as simple as a fuse.
We recommend taking a few minutes to check your fuse box & replace the fuse as necessary. Keep us posted!
Please subscribe to the channel and turn on your UA-cam notification Bell 🛎 that would be awesome thanks again!
😎👍🔧🔩
yeah. theres some fuses that are missing. like the grey box looking fuses. do you know if those have anything to do with lights? sorry im no car person lol
Its rare that the actual light burns out which leads me to the 101 splice kit. Recently I spoke to an individual that had a shop look at his car dealing with same issue and found that one of the wires within the 101 Splice kit had rusted/burned to a point that was not allowing it to allow electric current to pass through it. 101 Splice kits can get pretty expensive when having shop or dealership repair them.
Hey, my fuses are ok both in that fuse box and the cluster in the car. Front lights work fine, but might time tail lights don’t. Break lights work though. This started when I replaced the front drivers H/L bulb. Can you help?
Evan White
Thanks for watching Evan! Let’s get this figured out! It’s possible that a fuse has blown. We recommend checking all fuses that reference lights.
Next check all wires feeding into fuse box. Look for any signs of stress...melted wires, frayed wires...
Let’s start there! Keep us posted!
Please subscribe to the channel and turn on your UA-cam notification Bell that would be awesome thanks again! 😎👍🔧🔩
DIY With Michael Borders fuses are ok. Checked the fuse mentioned in the video and the cluster fuse. I will now check the wires I guess. Forgot to mention that the tail lights worked ever other day in the beginning, but now not at all.
Evan White
Thanks for the reply! Lights working intermittently is almost always due to a loose ground connection. At this point it’s important to check all wire connection points as well.
You may want to remove the new bulb you put into the front drivers h/l. See if this alters the activity you are experiencing. It things go back to normal...we need the address the front drivers h/l wiring, harness, and get a different bulb.
DIY With Michael Borders I will check this tomorrow and get back to you
Evan White
😎👍
had no luck with this on my G5 but I'm nervous to try replacing my gauge cluster. any suggestions?
Its rare that the actual light burns out which leads me to the 101 splice kit. Recently I spoke to an individual that had a shop look at his car dealing with same issue and found that one of the wires within the 101 Splice kit had rusted/burned to a point that was not allowing it to allow electric current to pass through it. 101 Splice kits can get pretty expensive when having shop or dealership repair them. Keep me posted
Was a parking fuse apparently
Lord Flick Awesome thanks for the update....So all is good ? 😀👍
Yup. No more problems ... for now
Awesome ! Thanks for the update!
my celica toyota have no dash ligths at all and no aircon even when starting it totally black out...i called my electricians twice and fix f9r an hour but after rested an hour still black out...what happened??lossen wires??i dont know...
Thanks for checking out the video. It can be a couple different things.
Its possible that the wires have been harmed...such as over heating/melted. Take a few minutes and inspect your wiring under the hood near the firewall as well as the wiring inside the car near your foot pedals.
Its possible that your "Ground Wire" has become loose which leads to the intermittent operation of the lights.
Check the fuse box...Verify that you have the correct fuse in the slot for the lights...example: if it calls for a 10 fuse...make sure you insert a 10 and not a 15 or 20.
I have attached a video that shows me replacing some bulbs behind the instrument panel...it might help you. Keep me posted
Please SUBSCRIBE to the channel that would be awesome thanks again!
ua-cam.com/video/Q8MDOZg1hZE/v-deo.html
my Toyota Camry speedometer lights only works in its half left side. Everything else works fine in my dashboard. Do you think its a bulb or fuse issue?
Thanks for checking out the video and sharing your comment and experience. Its definitely possible that you have a bulb that is burnt out. I experienced the exact same issue with half the lights working and the other half not working. I have attached a video that shows me replacing a bulb on my Toyota. Keep me posted. Please SUBSCRIBE to the channel that would be awesome thanks again!
ua-cam.com/video/Q8MDOZg1hZE/v-deo.html
DIY With Michael Borders Thanks for replying so quick! I'll check it out right now
Very cool, thanks again and keep me posted!
i checked all the fuses, every one is good. how do i know if the bulb behind the dash board is still good? if its bad how do i change it without calling mechanic.
As well as all fuses under trunk?
Do you know what fuse it would be for a 2007 Chevy Aveo Hatchback?
Grace Thompson Thanks for checking out the video Grace. It should be the same fuse. Keep me posted on your repair. Please subscribe to the channel and turn on your UA-cam notifications that would be awesome thanks again Grace! 😎👍
I've checked the hatchback vs the sedan fuses boxes and the hatchback doesn't have that fuse by that name....so I'm wondering if it's just labeled differently in the hatchback?
Grace Thompson After opening you Door, you will notice a small plastic access door on the side of your dash...left of Steering wheel. Inside are additional fuses. Locate the (Cluster) fuse and see if that has blown.
Chevrolet Aveo uva when I connect with battery then tail light back light dashboard lights automatically on.can not off it
Sourav Halder
Thanks for watching & sharing your experience. We recommend checking all fuses & verifying all electrical connection points are secured.
Keep us posted. Please subscribe to the channel and turn on your UA-cam notification Bell 🛎 that would be awesome thanks again!
😎👍🔧🔩
Did this on my g5 that had the same problem except the fuse kept blowing once i started the car and before I started it the gauge lights flashed on and off
Good morning and thanks for reaching out to us. It sounds like you have a short or a loose connection somewhere along your electrical wiring.
Do a quick inspection of your wiring that feeds in and out of fuse box and ensure you do not see any loose connections or signs of stress such as melted, frayed, or crimped wiring.
😎👍🔧🔩
it worked thank you!
Patricia Toth Awesome! Thanks for checking out the video and sharing your update. Please Subscribe to the channel that would be awesome. Thanks again Patricia 😀👍
my dash light of toyota tacoma 2006 doesn't comes on? do you guys have a video of those?
+Jocelyn Riedel No...have you tried all the tricks shown in this video? Also read all the comments below because there are a few other options to explore. Thanks for viewing. Subscribe to the channel thanks!!
+Michael Borders OK thank you.
what if that fuse is good. is there another fuse that will stop it from working? my tail light works now but the dashboard still out. someone told me it may be the bulb in the dashboard. i dont know what im doing and trying to fix on my own without expense of mechanic. can you help me? 2009 chevy aveo. thanks in advance
Down by where the pedals are inside car sitting in drivers seat, you will notice a fuse cover on lower left side. On the back of that plastic cover is a diagram of the fuse set-up. I don't have the vehicle in front of me but try to locate fuse that references radio/stereo/light....this may be you're problem. Keep me posted. Subscribe to the channel if you're up to it thanks again!
Hi my dash light went out on me , the speed thermometer and gas gauge isn’t working at all so I can’t see if I’m low on gas or how fast I’m going . Can you give me any advice if it’s related to the dash lights being out ? Thanks a lot 👍🏻
Thanks for watching & this should be a friendly DIY project. We recommend taking a look at the internal portion of your fuse box cap & locating where your instrument cluster fuses & fuel gauge fuses are. Check those & replace any & all fuses that have burned out.
😎👍🔧🔩
@@DIYwithMichaelBorders Thanks a million 🙌🏻
@@jeffcalderon
😎👍
I have this same problem with my chevy malibu
It's a transmission speed sensor. Look up video on how to change.
Does this also fix having burnt out needles on the guages
Ethan Smith
What’s up Ethan, thanks for watching & we hope the video helped. It should. Keep us posted.
We really enjoy making these helpful videos for our fellow DIY’ers. Many more helpful videos to come! 😀
Let us know if you have any questions. Please subscribe to the channel and turn on your UA-cam notification Bell 🛎 that would be awesome thanks again!
😎👍🔧🔩
What if i turn on only the park lights, and only the gauge light is not working? but the parklight/tail lights is working while the park light is switched on?
Buf if i turn on the fog lights, the gauge light will work. Usually if i turn on my parklight, the gauge light is on.
joshua busa
Thanks for watching & sharing your experience joshua. Have you verified all fuses & electrical wiring are in good clean working condition?
Keep us posted! Please subscribe to the channel and turn on your UA-cam notification Bell 🛎 that would be awesome thanks again!
😎👍🔧🔩
So what you are saying is I could just use the spare fuse?
manu gruni What’s up manu gruni... Thanks for checking out the video and sharing your comment. You can definitely use the spare fuse. It is important that you use the same size fuse...ex: don’t replace a 10amp fuse with a 5amp fuse...not good! Also after you use the spare, its also a good idea to refill the spare fuses so you have them handy when you’re on the road away from home.
Keep me posted on your repair! Please subscribe to the channel and turn on your UA-cam notifications that would be awesome thanks again 😎👍
I got one for you man my lights on dash wont work neither does my tailights only when I hit the breaks and the hazzards but when I turn on my lights nothing comes on
D21
Thanks for watching, have you already replaced the fuse shown in this video? If yes, lets direct our attention to the next possible fuse!
Down by where the pedals are inside car sitting in drivers seat, you will notice a fuse cover on lower left side. On the back of that plastic cover is a diagram of the fuse set-up. I don’t have the vehicle in front of me but try to locate fuse that references radio/stereo/light....this may be your problem fuse. Keep me posted. Please subscribe to the channel and turn on your UA-cam notification Bell 🛎 that would be awesome thanks again!
😎👍🔧🔩
2008 aveo same problem here except when iv plug a new fuse the dimmer switch in the car caught on fire 😮
Thanks for watching, any update? Did you use proper size replacement fuse?
will this work for my 2009 Chevy Aveo I have the same problem but my fuses are placed a little differently than yours
User Thanks for checking out the video. This should work! There wasn't much electrical change from 07-09...just slightly different locations as you mentioned. Please Subscribe to the channel that would be awesome thanks again 😀👍
Just bought new fuses from O'Reilly's and replaced both the pklp rh and the pklp lh but dash still won't light up.. could it be the lightbulb or other fuses? Something else I'm missing?
User Bummer...double check the electrical connection point on the bulb. Also check to see if the bulb needs to be replaced.
Also keep an eye open for any possible burnt or frayed wires...any signed if this might help solve the problem! 😀
What if only 1 tail lights out ?thats what ive got
@@spivzespivatron6712 k
I don't understand - don't the tail lights work at the start of video? You showed they turn on when you depress the brakes...isn't that how they are supposed to behave?
0pt618 Thanks for checking out the video. When this fuse blows...you won't have any Tail Lights after turning on you headlight switch. The only time your tail lights will illuminate is when you press the brakes. Sorry my video doesn't really mention it in that order. Subscribe to the channel that would be awesome thanks again 😀👍
Thanks for explaining it to me @DIY With Michael Borders.
Im glad to help. Love to have you as a subscriber. Thanks again!
I have an escalade and it doesn't show how much fuel I have nor does it show me the speed I'm going
Anthony, thanks for checking out the video. I did some research on your vehicle and I have found that many people have run into your very experience. Looks like there was a recall on the instrument cluster for this vehicle years ago. You vehicle is covered if still below 70,000 miles and less than 7 years old. I have found that most people experienced this issue around 125,000 miles.
There are other Escalade owners that have run into just one side failing while the middle and other side still work. There is usually 1-3 electrical connection points that clip into the back of the entire instrument cluster...one may have come loose...not likely though because if its just your fuel not working and your engine temp gauge is...then its connected.
I recommend calling the dealer and explain the issue...get a second opinion. The cool thing is there are a few UA-cam videos that show changing that instrument cluster. It might be something you can do at home. Keep me posted. Please Subscribe to the channel that would be awesome!
Hiya folks I've got a Skoda superb elegance 2012 model and the clock is half lit up but flickers now and again and by the way the speedo clock is factory fitted with leds any idea folks? Is it that fuse in the video I need to check?
Nasar Khan Thanks for checking out the video! From what you explain...my thought is that it's a short in the ground! Double check all wires and connections. If it's flickering...your fuse is still good! Keep me posted! Subscribe to the channel that would be awesome 😀👍
DIY With Michael Borders the clutch and flywheel was changed recently then this flickering happened so from what I gather the earth (ground) on car battery has a poor connection?
Nasar Khan Thanks for the update. Let me know if that fixes it!
Horn was working but stopped working after 100 amp fuse blew on the battery terminal. I replaced it. I also replaced the horn fuse but nothing. Any idea?
Thanks for watching & reaching out to us. Have you checked lamp fuse?
Just wondering my radio goes out also I check the fuse for it and it looks to be intact ? What can it be replaced most of the fuses too?
Thanks for watching & welcome to the DIY Raptor Club. Is it the original radio or an aftermarket radio? You may have a loose connection making the radio intermittent.
Hey, thanks for the video. I have a Hyundai Elantra 2001. There is no fuse called pk and I have changed the tail -RH (Cause its the right light and the dashboard not working), in fact I changed both tail fuses and nothing worked. Please help
thanks for viewing and commenting. I did some quick research and have found that it most likely is your ( Side Maker BULB ). The reason for all the outages is due to the fact that it all runs on a single circuit. This means once one item on the circuit goes bad "Or burns out"...it turns off all additional items on circuit. Change the marker bulb and see if that fixes the problem. Keep me updated. Subscribe to the channel if you're up to it. Thanks again!
+Michael Borders so I just found out its the fuse, whenever I change it with another 10 it blows immediately so I put a 30 and it's working perfectly. obviously I know this is ill-advised bt at least I know the problem when I take it to the shop. Thanks so much man
+Uche Nnorom Awesome thanks for the update! 😀👍
I have one for you. Tail lights work and all fuses are good. But dash lights don’t work. Thoughts?
Adam Mauch
Thanks for watching Adam, let’s get this figured out together! Down by where the pedals are inside car sitting in drivers seat, you will notice a fuse cover on lower left side. On the back of that plastic cover is a diagram of the fuse set-up. I don’t have the vehicle in front of me but try to locate fuse that references radio/stereo/light....this may be your problem fuse. Keep me posted. Please subscribe to the channel and turn on your UA-cam notification Bell 🛎 that would be awesome thanks again Adam!
😎👍🔧🔩
I have also a problem parklight and dashlights has no lights at the same time, can you help me please thank you
hi/hello i got kia cerato 2006 my dash lights don't work but its works when i reverse and i checked all fuse any idea what this issue can be thanks for any help.
Hey there thanks for checking out the video. I did a little research on this vehicle.
1. Several Kia Cerato owners have found the problem to be a lose connection behind the instrument cluster. This will require you to remove the cluster and check connections. You may even need to readjust the tension on the connection cable.
2. Previous owners have experienced a lose or acting up headlight switch which is on the same circuit and may alter the workings of other bulbs.
3. In 2006, there was a Manufacture Recall on this issue and was announced that all repairs by a certain date will be covered however that date is expired.....maybe the previous owner had it replaced.....any records of if they did or not????
Keep me posted....Subscribe to the channel that would be AWESOME :-)
thank you so much
Muse Ali thanks for watching 😀👍
My car dash blow the fuse with dashboard light tuning on whats the problem??
momen kareem
Thanks for watching & sharing your experience. The most common cause of this is an electrical short somewhere along the wiring.
We recommend doing a thorough inspection of the electrical wires that feed out of your fuse box & following it as far as you can.
Also check inside the vehicle near the brake pedal & make sure all wires & electrical connection points are properly secured.
Let’s start there! Keep us posted!
Please subscribe to the channel and turn on your UA-cam notification Bell 🛎 that would be awesome thanks again!
😎👍🔧🔩
I'm having the same issue with my 2008 ford f 150
Juan Hernandez Thanks for watching! Did you end up getting it to work?
Great video. I hope you can help me. I bought an audi a3 2008 and half of the miles per hour part of it it keeps blinking also from time to time the gas and oil lights in the middle flash. Could it be a fuse? Thank you
Thanks for checking out the video and sharing your experience. Since the lights are blinking at different times rather than completely not working leads to a definite short in the wiring system. This can be as simple as a loose ground wire. Do a thorough inspection of all your wires that lead to the under side of your dash. Verify that all wires are connected.
Check that the fuses are all in and secure in all the fuse slots. Also check the larger wire harness that runs from the fuse box to other wires throughout the dash. Lots to look at, so sorry !!
Another option it can be...however "In most cases" unlikely because your car is running fine...your Alternator may be starting to perform intermittently...which can cause the flickering of your dash lights. Like I said though, since your car is running good, this is most likely not the issue....but not to be completely ruled out haha!
Keep me posted. Please Subscribe to the channel and turn on your UA-cam notifications that would be awesome thanks again!
I just replace mine bt it keeps on blowin up am comfused now
Dash lights not working on my chev avio 2007
2:24 gunshot and a screaming dog. lol wtf
LOL oh my I never noticed that.....Creepy haha. Thanks for checking out the video.
lolol.. The dog sounded horrified!
I thought no one noticed I was like wtf it goes through the whole video if you really listen
holy shit hahahaha good find
i could be wrong lol but i hear this in Mississippi often. the dogs chase foxes. fox hunting club
my speedometer and lights don't work...any suggestions
+tyler hampton Have you tried the fuse that is for your radio?
Anyone know where to buy a speedometer for my 2004 g35
Luis Suarez
Thanks for watching Luis! We found a few good options on Ebay for your car. We recommend taking a look at Ebay & typing in 2004 G35 Speedometer! A few good options will come up.
Keep us posted on your project! Please subscribe to the channel and turn on your UA-cam notification Bell 🛎 that would be awesome thanks again! 😎👍🔧🔩
Smoke came out from behind my dash now I have nothing on the dash my clusters dont work or nothing
Coyote Trapper 85
Thanks for watching, we recommend disconnecting your negative terminal from your battery & inspecting all wires feeding into & behind paneling leading to your instrument cluster.
You may have a loose connection which is leading to a short...which is then causing the wires to overheat and/or arc which will lead to your symptoms.
Locating a loose connection point and then re-securing it & replacing damaged wires will hopefully fix your issue.
Keep us posted. Please subscribe to the channel and turn on your UA-cam notification Bell 🛎 that would be awesome thanks again!
😎👍🔧🔩
DIY With Michael Borders ok so it will come on then the top left hand side of the back of the panel gets really hot then the cluster stops working checked all the wires there good and the wires aren’t getting hit at all just the back of the cluster gets really hot
Coyote Trapper 85
Thanks for the update. Have you removed the entire Cluster for inspection? By chance have you pinpointed any specific wiring or connection leads that are hotter than others that feed into Cluster?
If you have access to replacing all light bulbs in rear Cluster, new bulbs may help eliminate increased heat...It’s uncommon however possible.
Keep us posted! 😎👍🔧🔩
how can i tell if its that? and where located?
You would need to use a volt meter to check electrical current...it's a bunch of wires that feed into a white harness that separates wires. It's located underneath the fuse box. Did you check the PK LMP fuse that I mention in video already!
My daughter just bought a 2007 chevy aveo ls for her first car and the horn is not working . I checked the fuses and they are ok. I am not sure if there is a relay for me to check next. Trying to fix ourselves and hopefully this is all that is wrong.
Jennifer Tucker
Thanks for watching. What’s your update? Have you been able to get your project solved?
Keep us posted. Please subscribe to the channel and turn on your UA-cam notification Bell 🛎 that would be awesome thanks again!
😎👍🔧🔩
@@DIYwithMichaelBorders I have not
thought I would try to figure out where relays were next. any clue?
Jennifer Tucker
Thanks for the reply. Most relays/fuses will be inside engine as shown here. There is also a small access door on lower left corner inside drivers side front...left of pedals. Check & verify fuses are not blown.
😎👍🔧🔩
@@DIYwithMichaelBorders I did check fuses. not sure what relay is horn
Hey, do you know what fuse I would need to replace for my 2005 Nissan Sentra? Plz reply quick thanks!
Luke Doraz
Thanks for watching & sharing your question. We haven’t worked on that vehicle in the near past & recommend contacting your local dealership.
They will ask for your Vin # and be able to pull up the exact diagram and location of your fuse.
We hope this helps. Please subscribe to the channel and turn on your UA-cam notification Bell 🛎 that would be awesome thanks again!
😎👍🔧🔩
Sameeeee Problem on The Same car
Jelly Thomas18
Thanks for watching & hopefully this video helped as you mentioned you have same car. 😀
Please subscribe to the channel and turn on your UA-cam notification Bell 🛎 that would be awesome thanks again!
😀👍🔧🔩
Clean that battery terminal!
Thanks for watching & welcome to the DIY Raptor Club. Good idea, that poor terminal is showing its wear & tear.
😎👍🔧🔩
"What a battery, guys... Have you've got any Saxon shirt? Have you ever been to Mexico?!" 🗨😤👕♨️🎭🔖🔋💸
Davide Madera
Thanks for watching, hope the video helped. 😎👍🔧🔩
Thanks guys
Alan Quarrie
What’s up Alan, thanks for watching. You are very welcome. Us fellow DIY’ers need to stick together, many more helpful videos to come! 😀
Please subscribe to the channel and Ring your UA-cam Bell 🛎 that would be awesome thanks again!
😎👍🔧🔩
Hope this is the problem with my 2000 Ford Explorer, I’ll have to check the tail lights and give it a try.
I'm having this same problem but my fuse isn't blown
+Kuchar Thanks for viewing and commenting....is your brightness turned all the way up? Sometimes you can't see the lights during the day
+Michael Borders I figured it out I made a comment on another video describing how to fix it. But in my case my dash lights wouldn't work my brake lights wouldn't work and neither would my license plate lights and for most people it is the instrument illumination fuse but in my case and most ford cases it is the main light switch fuse
Thats great, thanks for the update. This will help our future viewers!
yes thank u
Good morning, just poured a ☕️ and am sitting down to answer any and all questions for the DIY community.
You are welcome, we are honored you took the time to share this. Let us know if you have any questions and hey if you’re interested, join our DIY ecosystem and help us grow an exclusive group of DIYers.
toolboxtoken.com
Reach out to us any time! 🧰
I was able to use this as a fix but the fuse keeps blowing after a minute or two, any ideas?
Kevin Grove Thanks for checking out the video. This can definitely be an annoying issue. In short...as you know, Fuses are specifically designed to save the electrical system and its wires. Most of the time you run into a fuse blowing on a consistent basis...you may have a short. (Possibly exposed wires that are coming into contact with other wires).
I would first disconnect your battery and then begin to look for any frayed, loose, burnt, or damaged wires near your electric box under the hood as well as near your tail lights. If you come across any signs of damaged wires...you'll need to address them. In some cases, electrical tape can be used to secure any open wires however my recommendation is to get a second opinion from a MX shop due to the possible severity of a bad electrical connection. Keep me posted...we can get this figured out together! Please Subscribe to the channel that would be awesome thanks again 😎👍
Ok so I checked the wires and couldn't see anything, unfortunately my large head could get that far under the fuse box, but from feeling around I didn't feel anything loose or open. I just put another fuse in and it has not blown out yet. Thanks again and I will keep you updated later tonight if it happens again (hopefully it doesn't)
Kevin Grove Very cool. That's good news! Also you might want to check the connection points that your fuse fits into and clean out any debris/corrosion....Make sure your battery is disconnected....if you have an air compressor, you can try to use the air hose nozzle to remove any/all dirt, lint, leaves...
You are an angel! That you so much!
dice portz
Thanks for watching & we hope the video helped. We appreciate you reaching out to us.
We really enjoy making these helpful videos for our fellow DIY’ers. Many more helpful videos to come! 😀
Let us know if you have any questions. Please subscribe to the channel and turn on your UA-cam notification Bell 🛎 that would be awesome thanks again!
😎👍🔧🔩
Not my fuse, must be a bulb
Dcdatruth85
Thanks for watching & sharing your comment. Keep us posted on your DIY project & if replacing the light solves your issue.
Please subscribe to the channel and turn on your UA-cam notification Bell 🛎 that would be awesome thanks again!
😎👍🔧🔩
Replace the fuse still doesn't work tail lights work but not the dash
Thanks for watching & welcome to the DIY Raptor Club. Do you see any loose wires or damaged wires...crimped, melted, exposed & rusted wires near the fuse box? Keep us posted.
Hope all is well. 😎👍🔧🔩
How about telling us why the fuse blew. They don't just wear out......
Thanks for watching & welcome to the DIY Raptor Club. Examples can be...
• Electrical overload
• Overheat
• Electrical short
• Old corroded fuse
• Wrong fuse installed
• Having over 10,000 hours of accumulated time on fuse
Let us know what you find. We are curious to see what caused yours to blow.
Enjoy your night! 😎👍🔧🔩
my radio works ...but every time i put a fuse in for my cluster and turn my lights on it blows the fuse ...and my tails don't work
+tyler hampton Check out this video and let me know if this is similar to your issue. Keep me posted!
ua-cam.com/video/p7RKc0KG690/v-deo.html
It is the same problem but I have a 07 Aveo ..the fuse box is different
+tyler hampton bummer...let me check a few things!
+tyler hampton have you checked all fuses in this forum?
www.g3integra.com/side-jobs/chevy-aveo-lights-not-working/
Thanks for help!
OfficialAdvanced
You are very welcome & thanks for watching! Keep us posted with any questions you may have.
Please subscribe to the channel and turn on your UA-cam notification Bell 🛎 that would be awesome thanks again! 😎👍🔧🔩
Go get gas⛽️
Bayleigh N Owen Thanks for checking out the video. Hope it helped. Please Subscribe to the channel and turn on your youtube notifications that would be awesome thanks again 😀👍
DIY With Michael Borders thanks for the great upload
I have a nissan b13 sentra and dashboard lights aren't comming on
Justin Ramdass
What’s up Justin, we appreciate you reaching out to us. Have you checked all fuses inside the engine compartment as well as down below to the left of your brake pedal. Keep us posted. Us fellow DIY’ers need to stick together!
😎👍🔧🔩
@@DIYwithMichaelBorders I checked the fuses inside and out all is good and another problem the reverse light isn't comming on as I changed the bulbs As well as the temperature gauge it all happened the same day
Justin Ramdass
That’s no fun. Any recent MX completed to vehicle. This may help us determine whether or not any recent MX is tied to your issues.
Theres an issue for me. There was a 20A fuse where the PK/LP RH 10A fuse should be, and Im a little worried that there is some electrics fried as nothing is turning on and the fuse isnt melted
Wingstar
Thanks for watching & we hope the video helped. If your vehicle is a 2007, we recommend removing that 20amp & installing the correct 10amp fuse. If your vehicle is not a 2007, it’s possible that your system uses a 20amp. Check the inner side of your cap & see what it says....10amp or 20amp...???
We really enjoy making these helpful videos for our fellow DIY’ers. Many more helpful videos to come! 😀
Let us know if you have any questions. Please subscribe to the channel and turn on your UA-cam notification Bell 🛎 that would be awesome thanks again.
😎👍🔧🔩
@@DIYwithMichaelBorders I have already checked the underside of the fuse box lid, it does say that it needs a 10 amp fuse. Mine is a 2008 and I am fairly sure that it is the same inside and out. Thanks for the reply 👍👍
Wingstar
Very cool. Insert a brand new 10amp fuse. Keep us posted.
😎👍🔧🔩
What if all warning lights are on
Thanks for watching & good morning, we are drinking our morning coffee answering any and all questions for the DIY community.
We recommend performing a friendly reset. To do this, disconnect the black negative cable from your battery and leave disconnected for a minimum of 30 minutes.
This will allow your onboard computer to reset. After 30 minutes, re-secure black negative cable to your battery and start engine.
Keep us posted. 😎👍
@@DIYwithMichaelBorders thanks for replying,no it didn't worked lights still on , any other soultion?
@@kboss0604
Good morning, that’s what we’re here for. We DIYers need to stick together!
Have you checked all fuses including the fuses inside vehicle down near your pedals on left side?
@@DIYwithMichaelBorders which one I should check
@@kboss0604
Thanks for the reply. We recommend looking at the diagram on inner cap at checking all fuses related to lamp, lights, & instrument cluster/panel.
my speedo metter light is not working help
study times
Thanks for checking out the video! Whats the update...Have you checked the Pk/Lmp fuse yet? In most cases, its the fuse however if your fuse is still good, we need to look deeper into the electrical system. There might be a short somewhere. I recommend removing the tail lights and checking to see if you see any loose wires...usually never the case however we can't rule it out...In addition, its possible that the splice kit/box may beginning to fail...again less likely than a blown fuse! Keep me posted! Please Subscribe to the channel and turn on your UA-cam notification Bell 🛎 that would be sweet! Thanks again!
@@DIYwithMichaelBorders thanks for the reply i will check that and update you soon
study times
😎👍🔧🔩
its working now but there is a problem arise speed niddel light is not working all niddel have red light effect but speed niddel doesn't
My 05 aveo dash lights don't work either. Can't find the problem though. It's just a cheap crappy car.
Seth Burkholder
Thanks for watching Seth! Let’s get this figured out! Have you located the fuse shown in this video & replaced it?
Keep us posted! Please subscribe to the channel and turn on your UA-cam notification Bell 🛎 that would be awesome thanks again! 😎👍🔧🔩
🤙🏼👌🏼
AJ Clark
Thanks for watching. Let us know if you have any questions. Us fellow DIY’ers need to stick together!
😎👍🔧🔩
not helped to fix deshboard.
Thanks for watching, we appreciate you sharing this. Bummer, do you see any signs of melted wiring or electrical connections?
Please let us know if you have any questions.