Hi Matt, you saved my Life !!! I lost every connection some weeks ago. My profile also was gone so I was only 'guest' in my car. I was sure I had an update version 2.x then fall back to 1.x. Very bad. With your instructions I had regained internet. Bad thing to bring back the lower part with the 4 screws but finally I did it. Then I tried to reconnect my fisker app, scanned QR-Code, then the app gave message 'someting was going wrong'. DIdn't get that but my profile on the car was back. Hoping now for updates, will see waht comes. Again a BIG BIG THANK YOU!!! GREAT WORK!
Thanks Matt, I went in to try to troubleshoot the rear trunk 12 volt that stopped working after 1 use a year ago. I was told the fuse must had blown and Fisker never fixed it when I did get some service. It was not blown after all so not sure why it's not operational but it gave me the opportunity to follow your instructions and reset the t box. Your instructions were clear and concise. I need to buy the fuse switch next and install.
Yes, the fuse switch has come in handy a couple times already since I have installed it. Luckily I haven't needed to use it since getting v2.2. The 12V outlet is fuse RF36 for those that are interested in knowing.
Absolutely brilliant. HUGE thanks. Hasn't happened to me yet but now I know. Anyone doing this, PLEASE be careful. If you do something wrong and Fisker support is no longer available you might end up with something worse than a stuck Nav screen. So, BE CAREFUL. I have some something fairly similar in disassembly and reassemble with my 92 BMW 850i where I had to take out the general control module and switch out capacitors. So, that was more complicated but the disassembly and assembly was pretty similar, removing panels under the steering wheel. I took my time making a 2 hr job a 5-6 hrs job taking breaks in between to breath and slow down to be patient. NICE video.
Thank you! Followed instructions and fixed my issues with the clocks out of sync, not being able to go into deep sleep, no 4G connection and not being able to connect to a Wifi access point. Was nervous since I just got the Ocean One yesterday LOL, but figured that unless I got it working I wouldn't be able to get the OTA 2.2 update (and probably why it wasn't updated as of yet). Great instructions, just wished I had the connector to extend the fuse so it the event I needed to do it again, I'd be all set.
I'm not much of a handy person, do you think it would be easier to unplug the battery under the hood? or any other way to cut power to reset? @@MTNRanger
@@krafter324 That will possibly fix the issue, but then you lose your doggie windows that will require an in-person service tech calibration. Once the switch is installed, it's much easier than any alternative.
Thank you for your video. Mine needed a reset too. I followed your instructions and the Spotify, Wi-Fi work again. The two clocks on the displays and date are all fixed and it would go into a deep sleep again. 🎉
Thanks as always @Matt! 🙌🏽 You da man! Would doing this solve deep sleep again? I haven’t been able to get my FOO into deep sleep after the 2.1 OTA update 🙄 which I need to do to to reset lane change assist and front ADAS.
@@MTNRangerunfortunately removing the RF22 and RF55 fuses last night did not fix and reset the inability to deep sleep again. I’m not sure what else to do. Being in Canada we no longer have service techs. 😢
I just wanted to take a moment to say thank you. I live in a metro area that has frequent outages of my 4G, and after following your instructions and then seeing no connectivity, resetting the T-box restored my connection. Thank you for taking the time to make this video.
Great video. I just did this reset a few days ago because my cell service stopped working, pulling the fuse for a minute has fixed it so far. Wish I had your video, it would have made it a ton easier!! One addition that I did notice, and maybe you did this and we couldn't see it, is when putting the lower cover back on by the pedals, there is a metal mount or tab near towards the front of the vehicle that that lower cover latches into, it seems to keep the cover raised higher and better fitting around the floor vents. Thanks again, Great stuff!!!
Thanks for clear step-by-step instructions. I was able to easily follow along and reset my t-box fuse thanks to this video! Next time this happens I’m going to install that relay switch.
Matt, thanks for reminding me of this video. I had watched it when it first came out, but because i wasn’t having that specific problem, I forgot your tutorial. Now that my navigation has stopped tracking, I’m going to revisit your video and purchase your future workaround toggle switch. You are a life saver. Particularly in this climate of uncertainty with our Fisker’s function-ability. Thank you again. Wish me luck. 🤭
My 4G signal goes out quite often, so I finally decided to do the t-box reset procedure. I also ordered the switch using your link, to install tomorrow when it arrives. Thank you for the video, it was very helpful.
Hugh Shout out to Ocean Views by MTN Ranger. Finally, saw the red icon appear on Fisker Ocean Navigation after TBOX reset. The step by step instruction, parts/tools needed and precaution commentary on the video is right on the money. Finally, navigation is alive and rocking...
Just did my install, thanks so much for the video, it very much helped! Basically followed your process except I fed the switch down from the top. I got the 30cm version and it is still more than enough length. My 4G and connectivity came back after my install was completed! The only thing that was a bit of a pita was the three metal clips that fell off the very first trim piece you remove. Luckily I was able to fish them out from where they fell and put them back when I re-assembled. Otherwise no issues! Thanks again for the video!
Yes, I have installed more of these and installing from the top is the way to go. The door threshold piece does tend to lose those clips. I usually use a needle nose pliers to extract them from the hole.
Thanks so much for this video. After a recent 12v drain and jump, I still had maps and navigation but both clocks were off (and didn’t match each other) and my 4G had stopped working which concerned me because I am still waiting for the 2.1 push which needs the 4G. I pulled the RF22 first which did not resolve the issue but pulling the RF55 then rebooting the infotainment did. Anyway, I was very nervous but your clear instructions made the process way less painful. Appreciate you and all you do for the community!!!
I did this and it works. The video is an excellent guide, and it went perfectly. I used a 30 cm bypass switch and didn't have to take out the top screws - I just fed the blade end down from the top.
@mountainranger - Followed your meticulous instructions and it fixed both the stuck navigation and Bluetooth connection problem. You are a god send to the Ocean owners. Thank you.
Once a cabin filter becomes available, I will gladly make a video! Note, most cars have them replaced every two years, so we have some time before it becomes necessary.
Nice! Interesting enough … I am in communication with the original manufacturer to see if I can make a bulk order. They are looking into it and I’ll let ya know the results when I get them . Thanks again
I had problem connecting to home wifi after update 2.0 and saw the post on FOA regarding resetting the tbox. I did the 15a fuse but that alone doesnt work. Both 15a and 5a together does the trick. Thanks for the instructions.
Sorry. I saw a comment that said they used a 30 cm extender. Thanks again. Having difficulty getting the piece below the steering wheel back in correctly.
Brilliant… thanks you so much for posting those educational videos. I guess if fisker goes under (maybe the question is not if, it’s when), you are going to be the go to guru :)… I’ve been experiencing issues with my ICC for the last few weeks, it would go black while driving, could not access anything, including AC, soft reboot did not work. The moment I stops it would go back! A technician came over and did hard reboot by disconnecting the 12V battery, one week later the ICC went completely down!!! I put another ticket, and now it’s been a week no one has called! Do you think this something has to do with the fuse box?
Thanks! With that description, I think you may need the ICC module replaced. I would check to see if a fuse is blown. Check out the Facebook "Fisker Ocean Maintenance and Tips" group, lots of good stuff in there. We already have a service manual available to download.
Hi Matt or anyone else on this comments thread… Has anyone experienced a blank infotainment screen that doesn’t return to normal ops and stay blank. I have attempted multiple soft resets (on the steering column wheel) which results in the FISKER OCEAN startup log (10:27 in the video) coming up on infotainment screen then it goes away and stays blank. Anyways, looks like the infotainment screen is no longer operational (stays blank). Does anyone know if in need to reset a fuse or something?
If you see an image on the center screen during boot, the fuse is fine. If the screen is always blank, that would probably be the fuse. I'm not sure what is causing your issue. If you put the car in reverse gear, does the rear camera show up on the screen? Have you also done a deep sleep reset?
@@MTNRanger Yes, I did attempt a deep sleep rest and it hadn't resolved the issue (also the rear camera did show on the infotainment screen while in reverse but that was the only thing that worked with the blank infotainment screen; additionally all the drowsy driver warning started to appear as well while driving and the infotainment screen was inop). At about 8-10 hrs later after I initiated the deep sleep reset,, the problem went away. here's the resolution: I was lucky to get Brandon from Platinum Precision (former Fisker Tech) from the DMV area to help me with the issue. I happen to have an appointment with Brandon the very next day to get my water pump replaced and opt'd to get the 2.2 uploaded as well. He was able to do a hard reset on the center console but only after the HVAC controls came up. This happened only after about 8-10 hrs after I initiated the deep sleep (FYI: immediately after the deep sleep was entered about 2 hours after initiating the deep sleep, I still didn't have the HVAC control come up nor did the infotainment screen recover either) and btw, my vehicle initiated charging at 8Amps as well. I have been checking couple times since the issue was resolved while Brandon was at my location and it seems to be stable still. I'm glad that Brandon was able to reset the infotainment panel thru the switchology of the HVAC. Figures crossed (for now) that the center infotainment console would stay operational.🤔 The Switchology to do the hard reset was the following (if you are lucky to recover the HVAC controls (after a deep sleep reset) without of course the infotainment central screen up and running): set Driver Side Air temp to Highest possible setting (i.e. highest temp), then set the PAX side temp to the Lowest possible setting (lowest temp), then set fan speed to 7, and then activate the Rear Defrost. It immediately cycled the power to the Infotainment Center Console (by itself) with the Fisker Logo coming on and after a few mins, recovered my infotainment screen. Thanks to Brandon for helping me dodge having to replace the very $$$ ICC (for now).
Thank you very much! Since update 2.1, i don’t have the image from the front and rear cameras on my central screen when i park. Is it possible that this is due to a fuse ? Thanks again
I cover that in this video: ua-cam.com/video/Jawk2kphI8E/v-deo.html I am working on an alternative where you can still use the lights, but only controlled by the overhead console buttons.
Once again, thank you for this video. I followed it as I installed my switch and it woks like a charm. 🎉 Now i have to wach the 12 v battery one, since i keep getting the warning, blocks me from putting it in reverse and when I restart it goes away. So I’m not sure it’s really the battery or just more garbage warnings. 😮
My driver door NFC is not working , and handle LED is not glowing and trunk cannot be open by button located on driver's door, is Toolbox have those settings ? your help is much appreciated
I have seen fuses for the siren and the horn, but I haven't found a fuse specifically yet. Eventually, I'll do a video showing how to disconnect the PWS speaker. It's on my to-do list.
I think I know the answer to this. All was going great with my Ocean and, all of a sudden, I see Spotify, Iheart, etc. but none of them load. I am thinking I need to do a t-box reset. I could pull the fuse and reinsert, which I will probably do and if it works here are my 2 questions. Do you believe it's possible that I need to do a t-box reset to get those audio programs working. By the way I can still play spotify, iHeart, etc via my phone connected to the Ocean with bluetooth. And second question. Which of the Fuse Bypass Switch/Extenders did you buy? The 30cm or the 60cm in length? Great video which I probably knew I would need to access at some point. I am almost tempted to just leave things alone and use Bluetooth. My navigation seems ok, still wroking.
I personally have never had an issue with the apps not loading. Having them crash, yes, that does happen from time to time. I don't know if resetting the Tbox fuses will fix this. But I would still recommend trying it. You can use the 30cm length extender - I have in fact installed that one in another owner's car. I only used the longer one since it was the only one in stock.
I’m not at this moment in my inquiry, but definitely will if I get the numbers from manufacturer. Gotta first see if they will start production and at what price per count etc 👍
Thanks for this informative video. Looks like we need more of these to be able fix our wonderful vehicles our selves from the look of things. Any suggestions on how to fix the cameras/blind spot lights permanently on issue? Can it be fixed with changing fuses? Other question is if Ocean can work with Ottocast P3 OttoAIBox CarPlay Ai Media adaptor?
The cameras and blind spot detection issues are bugs that needed be addressed in software. Resetting fuses will not help that issue. No, an Ottocast P3 (or other device) will not work with the Ocean.
@@MTNRangerThank You, My LCA wasn’t working and I can’t get the mirror to move, the passenger mirror won’t close when I lock the car I’m guessing it’s a faulty fuse
Hey MTN Ranger. My car has no cellular or wifi connectivity since they attempted to push 2.2 to it. I tried your Tbox reset but it doesn't seem to have been effective. Any other advice for a case like this? Thank you!
So, 4G and Wifi worked before the attempted update? If so, you should contact FOA to see if there is something they need to do with any of the modules.
Hi Matt! Great video. Watched it when you first released it and hoped that it was merely for my entertainment. However, coming back from a trip to Detroit, I was listening to Spotify and wanted to change to TuneIn. At that point, the T-Mobile connection, according to the bars, was and still is gone. The radio still works, but none of the entertainment apps work either. Oddly, TomTom still works but the lady has laryngitis. When I first start the TomTom in the morning, she comes on and tells the estimated time of arrival, but then goes silent. I suspect it is from being hooked up to the home WiFi. Judging by the radio audio, when a turn comes, the speakers at the front are attenuated and stay that way for about 10 minutes. Do you think this issue is related to what you are describing in this video?
It's hard to say. I've never had the issue you describe. Sometimes things can be buggy and a deep sleep reset or overnight seems to fix them. Other times, pulling the fuse works. But what you describe sounds like either the ICC or Tbox. Pulling and resetting either or both fuses may help.
Just watched this and was wondering if I could apply this to my own situation. My Android will no longer work with the car. Calls come thru but voice is just static. Couple questions. 1) Do you know which fuse controls the phone/voice? Would it be the same fuse? 2) When taking the fuse out and waiting for a reset are you having the car on?
The RF22/55 fuses control the Tbox and ICC modules. When pulled also turns of the center display. I'm not sure if there is a specific fuse for the phone/voice. Yes, the car is on when you remove/reinsert the fuse (it's technically always on!)
Since Fiskerati closed, the only other one I know of is Oceanforums.com. However, there is no centralized help section and until recently was a toxic site.
pulled out 15Amp, screen went off, but after re-inserting the fuse (more than a minute without fuse) - screen cme back up and navigation still frozen at home address
It's also possible you may have an issue with the ICC module (which communicates between the car and the network). Unfortunately, there may be more than one cause of the navigation locking up.
Hello, thank you for your video! My internet only works around 1% of the time and I’ve tried your method of resetting the Tbox by removing the RF55 and RF22 fuses, separately and together and have tried soft resetting but my internet works only for a couple minutes upon restarting the car and then goes away. I’ve also replaced both 15 Amp and 5 Amp fuses with new ones. Do you happen to have any other suggestions? Because of this problem my car is still stuck on 1.11
It sounds like you may have a problem with the ICC module (which controls communication). Either it needs a firmware update or be replaced. When did you get the car and where are you located?
Great video. May be you can help. My Dcc fast charger won’t work. It tries to connect to vehicle and then end up with “charging start error”. Do you know what fuse I could try to may be reset it! ? Thanks
Have you tried different CCS station? Some are not compatible (or giving issues) such as the EVgo 100kW stations. I'm not aware of which particular fuse controls charging.
Hello, Thank you very much for the great video. I am from Germany and have had my Fisker Ocean Extreme since December 2023. There is no longer any support in Germany. After Update 2.0 I have no longer a connection to the apps and the internet. Date, navigation and updates are no longer possible. I tried to reboot the car using the main-switch near the battery. But that didn't work. Do you think I can reactivate the navigation system and the internet connection by using your suggested method? I would be very happy about a short answer. Thank you and greetings Germany
@@MTNRanger Thank you for your quick answer! I'll try it tomorrow morning and I'll give you feedback. Do you think I should remove both fuses at the same time or only one at a time andd step by step? And you also think waiting for 1 minute might be enough? I often read in German forums, that you should wait 10-30 minutes for other systems to restart. Many greetings from Germany.
@@joergebenhoch You could remove both, but try RF22 first. Everything I have seen only requires about a minute before reinserting. It would not hurt to wait longer if you wish. In any case, I would do a infotainment reboot after you reinsert the fuse.
@@MTNRanger Thank you :-) Is it sufficient if the Fisker is opened with the key or NFC? I don't have to press the brake pedal either? By restarting the infotainment you mean that I hold the two inner buttons on the steering wheel for 15 seconds?
@@joergebenhoch Opening method does not matter. You press the brake pedal to wake the car up or put it in ready mode. Yes, pressing the two inner buttons on the steering wheel.
MTN Ranger, My Center Infotainment Screen is inoperable - When starting up the FOO the OCEAN script and FISKER Logo appears, then the screen goes blank. Unfortunately, this TBox fix does not reset the main screen. Any ideas on which fuse this could be? Thanks for a great video here about reset of GPS and Navigation.
Hello, my 4g suddenly stopped and i vannot connect to any wifi. It started when parked for 6 hours. Only think i noticed was 12v battery did dip below 12v while parked. Normally it stays above 12v. Is this fuse pull a fix for 4g and wifi?
@@MTNRanger is it possible the 12v battery monitor can prevent the car to sleep. Since I successfully installed it a few days ago I cannnot get the car to sleep. I also cannot get the energy saving modes to trigger. I want to do a deep sleep before I pull the fuse. Maybe I'll disconnect the monitor first. I know it uses power from 12v to send Bluetooth. Maybe this draw is keeping car alive on the version I have.
@@petertierney994 It may be possible, but I have not heard anyone bringing it up before. The huge number of modules in the car and their respective versions may cause different outcomes on different Oceans. Yes, I would test without the monitor to see if it goes back to the original functioning.
So it worked with just the one fuse pull, my wifi reconnected and I say the 4g flash before wifi. Will take for a spin to confirm 4g after I put car back together. Wifi always errors on connections unsuccessful but I see it connected on my router and the internet on the car works now.
Hi MTNranger, do you think it would be ok to not put back the first screw that you removed in the video or do you think the panel will fall off? It seems that the clips and the bottom screws were able to keep the plastic panel in place.
I guess I have been lucky with my FOO in that I have not had a problem with the navigation location being stuck. I do have the issue with Navigation updates not working, and the maps showing as 19 months old. I reached out to Tomtom and was told that they update the maps every 3 months. Lastly, for my navigation it shows states that I have never driven to as being "Region in Use". On my car it shows the state of Washington in Use and my car has not left California. I really hope that the Fisker 3.0 update includes working updates to the Fisker Ocean Navigation maps.
The maps download has never worked on the Ocean. They appear to download but never install and error out. The points of interest are very poor in the navigation. I search for local destinations and it sometimes points to something 500 miles away when I know there is one 5 miles away. Very odd.
My car is on 2.0 and Fisker replaced ADAS module to make cameras work but it has made lane keep assist and blind spot monitoring unavailable. Do you have any tricks or suggestions to get them working?
You got me on that one. I think the tech should have calibrated/updated all the modules when replacing the ADAS module. I'm not sure I can suggest anything on that, sorry. Are they totally not available or do them come and go?
@@MTNRanger thanks for the response. Unfortunately those 2 items are completely unavailable. It was becoming impossible to drive with notifications switching between blind spot monitoring unavailable and lane keep assist unavailable. So I had to set them to disabled. Even after doing that I get a reminder on each drive that both of those functions are unavailable. I wish Fisker was in better shape to help me by sending a tech to troubleshoot it further. I have now given up hope on getting it working.
If you can do this, you can probably help with this? You'll be my hero if you can figure out how to make the reverse and below 23mph forward speaker sound not as loud or a way to 'legally' shut it off.
Ok, tonight I tested with the key fob in the console and I got 30 minutes of run time before the outlet turned off. Not quite as good as in the video, but still sufficient many outlet uses. You can press the brake pedal and start another 30 minutes of use.
@@MTNRanger you rock! Thanks. and maybe there's a way to muffle the sound so it's still on, road legal, but not as annoying. Can't tell you how much I appreciate your videos!
My GPS has worked all of 5 minutes since December. This is a lot of work and potential damaging of panels and clips. I may call for a technician instead.
I appreciate the video. But I have to wonder how often does a problem occur where you have to pull one of these fuses to reset the Tbox? Seems like a ridiculous amount of effort and expense for an owner to make their own tweaks to the vehicle to keep it working. Which leads me to think that this car has some pretty horrible electronics engineering design. Knock on wood, I have a FOE purchased in December, currently on 2.0, and I don't "think" I have any Tbox issues.
Some people have the Tbox lockup every week, others may not have the issue. I think given enough time, these problems would have been addressed by the company. Most are probably fixed with OTA software updates to the system. It's unfortunate that the owners have to do this, but with the company going away, there is no other choice.
it's so scary how this car is put together. A fuse box must be easily accessible. It shouldn't be necessary to take the car apart like that. What a piece of shit
![Lp. Сердце Вселенной #60 РОЖДЕНИЕ ЛОЛОЛОШКИ [Финал] • Майнкрафт](http://i.ytimg.com/vi/YoR0pAV9FVQ/mqdefault.jpg)
Hi Matt, you saved my Life !!! I lost every connection some weeks ago. My profile also was gone so I was only 'guest' in my car. I was sure I had an update version 2.x then fall back to 1.x. Very bad. With your instructions I had regained internet. Bad thing to bring back the lower part with the 4 screws but finally I did it. Then I tried to reconnect my fisker app, scanned QR-Code, then the app gave message 'someting was going wrong'. DIdn't get that but my profile on the car was back. Hoping now for updates, will see waht comes. Again a BIG BIG THANK YOU!!! GREAT WORK!
I'm glad you got it back!
Thanks Matt, I went in to try to troubleshoot the rear trunk 12 volt that stopped working after 1 use a year ago. I was told the fuse must had blown and Fisker never fixed it when I did get some service. It was not blown after all so not sure why it's not operational but it gave me the opportunity to follow your instructions and reset the t box. Your instructions were clear and concise. I need to buy the fuse switch next and install.
Yes, the fuse switch has come in handy a couple times already since I have installed it. Luckily I haven't needed to use it since getting v2.2. The 12V outlet is fuse RF36 for those that are interested in knowing.
Absolutely brilliant. HUGE thanks. Hasn't happened to me yet but now I know. Anyone doing this, PLEASE be careful. If you do something wrong and Fisker support is no longer available you might end up with something worse than a stuck Nav screen. So, BE CAREFUL. I have some something fairly similar in disassembly and reassemble with my 92 BMW 850i where I had to take out the general control module and switch out capacitors. So, that was more complicated but the disassembly and assembly was pretty similar, removing panels under the steering wheel. I took my time making a 2 hr job a 5-6 hrs job taking breaks in between to breath and slow down to be patient. NICE video.
Yes, patience and carefulness is the key!
Thank you! Followed instructions and fixed my issues with the clocks out of sync, not being able to go into deep sleep, no 4G connection and not being able to connect to a Wifi access point. Was nervous since I just got the Ocean One yesterday LOL, but figured that unless I got it working I wouldn't be able to get the OTA 2.2 update (and probably why it wasn't updated as of yet). Great instructions, just wished I had the connector to extend the fuse so it the event I needed to do it again, I'd be all set.
I'm glad it worked out!
Thank you again for leading the way on all of these maintenance and repair tutorials!
Thank you!
I'm not much of a handy person, do you think it would be easier to unplug the battery under the hood? or any other way to cut power to reset?
@@MTNRanger
@@krafter324 That will possibly fix the issue, but then you lose your doggie windows that will require an in-person service tech calibration. Once the switch is installed, it's much easier than any alternative.
@@MTNRanger oh good to know. Won’t do that!
Thank you for your video. Mine needed a reset too. I followed your instructions and the Spotify, Wi-Fi work again. The two clocks on the displays and date are all fixed and it would go into a deep sleep again. 🎉
Awesome, I'm glad you got it done.
Thanks as always @Matt! 🙌🏽 You da man!
Would doing this solve deep sleep again? I haven’t been able to get my FOO into deep sleep after the 2.1 OTA update 🙄 which I need to do to to reset lane change assist and front ADAS.
@@jjScorpio I didn't plan this to fix that issue, but it does seem to work for some people.
@@MTNRangerunfortunately removing the RF22 and RF55 fuses last night did not fix and reset the inability to deep sleep again. I’m not sure what else to do. Being in Canada we no longer have service techs. 😢
@@jjScorpio Can you send me a message at mtn_ranger@aol.com? I'll give some more suggestions.
I just wanted to take a moment to say thank you. I live in a metro area that has frequent outages of my 4G, and after following your instructions and then seeing no connectivity, resetting the T-box restored my connection. Thank you for taking the time to make this video.
@@bahgzd I appreciate that!
Great video. I just did this reset a few days ago because my cell service stopped working, pulling the fuse for a minute has fixed it so far. Wish I had your video, it would have made it a ton easier!!
One addition that I did notice, and maybe you did this and we couldn't see it, is when putting the lower cover back on by the pedals, there is a metal mount or tab near towards the front of the vehicle that that lower cover latches into, it seems to keep the cover raised higher and better fitting around the floor vents.
Thanks again, Great stuff!!!
Yes, when it pushed it towards the front and up, it seems to latch into it. If you don't do that, it falls down in the front by an inch or so.
Thanks for clear step-by-step instructions. I was able to easily follow along and reset my t-box fuse thanks to this video! Next time this happens I’m going to install that relay switch.
Good to hear!
Matt, thanks for reminding me of this video. I had watched it when it first came out, but because i wasn’t having that specific problem, I forgot your tutorial. Now that my navigation has stopped tracking, I’m going to revisit your video and purchase your future workaround toggle switch. You are a life saver. Particularly in this climate of uncertainty with our Fisker’s function-ability. Thank you again. Wish me luck. 🤭
My 4G signal goes out quite often, so I finally decided to do the t-box reset procedure. I also ordered the switch using your link, to install tomorrow when it arrives. Thank you for the video, it was very helpful.
Let me know how it turns out.
@@MTNRanger The installation went well. I installed it during my lunch time.
Hugh Shout out to Ocean Views by MTN Ranger. Finally, saw the red icon appear on Fisker Ocean Navigation after TBOX reset. The step by step instruction, parts/tools needed and precaution commentary on the video is right on the money. Finally, navigation is alive and rocking...
We're all in this together!
Just did my install, thanks so much for the video, it very much helped! Basically followed your process except I fed the switch down from the top. I got the 30cm version and it is still more than enough length. My 4G and connectivity came back after my install was completed! The only thing that was a bit of a pita was the three metal clips that fell off the very first trim piece you remove. Luckily I was able to fish them out from where they fell and put them back when I re-assembled. Otherwise no issues! Thanks again for the video!
Yes, I have installed more of these and installing from the top is the way to go. The door threshold piece does tend to lose those clips. I usually use a needle nose pliers to extract them from the hole.
Matt thanks again. GPS was down for 3 days. Didn’t want to do this but went for it and your video was key to my success. Thank you!
There are opportunities for Ocean Technicians to solve and repair the problems as you have been doing. Thank you for your help.
Thanks so much for this video. After a recent 12v drain and jump, I still had maps and navigation but both clocks were off (and didn’t match each other) and my 4G had stopped working which concerned me because I am still waiting for the 2.1 push which needs the 4G. I pulled the RF22 first which did not resolve the issue but pulling the RF55 then rebooting the infotainment did. Anyway, I was very nervous but your clear instructions made the process way less painful. Appreciate you and all you do for the community!!!
Thanks, I'm glad it worked for you.
I did this and it works. The video is an excellent guide, and it went perfectly. I used a 30 cm bypass switch and didn't have to take out the top screws - I just fed the blade end down from the top.
@@EdFry01 Yes, I should have routed it from the top. I realized during editing the video and slapped my forehead!
Thanks!
Thanks so much. I appreciate that!
Awesome, and thank you so much, the stuck navigation happened to me , will need to do what you showed here. God bless
@mountainranger - Followed your meticulous instructions and it fixed both the stuck navigation and Bluetooth connection problem. You are a god send to the Ocean owners. Thank you.
Hi,
Did you ever make a video on how to access the cabin air filter? Thank you
Once a cabin filter becomes available, I will gladly make a video! Note, most cars have them replaced every two years, so we have some time before it becomes necessary.
Nice! Interesting enough … I am in communication with the original manufacturer to see if I can make a bulk order. They are looking into it and I’ll let ya know the results when I get them . Thanks again
@@troychrisman7682 That would be very useful for the FOA. Are you working with them on this?
Hello and thank you for this super video!!! I had the same problem and after I did the way you did it works perfectly! Thanks a lot from Germany....
I had problem connecting to home wifi after update 2.0 and saw the post on FOA regarding resetting the tbox. I did the 15a fuse but that alone doesnt work. Both 15a and 5a together does the trick. Thanks for the instructions.
Yes, for some cars, doing resets on both fuses is needed.
Thanks for this video. This happened to me this weekend. I will follow your instructions.
U are awesome! Waiting for ur air vent changing tutorial video!
Cabin air filter? Yes, when a filter becomes available, I'll do a video for it.
OMG, thank you! I am going to try this. Mine hasnt' worked in months. Same with the communication on service orders lol.
Sorry. I saw a comment that said they used a 30 cm extender. Thanks again. Having difficulty getting the piece below the steering wheel back in correctly.
Yes, it is tricky. The angled clips do need some finessing.
Brilliant… thanks you so much for posting those educational videos. I guess if fisker goes under (maybe the question is not if, it’s when), you are going to be the go to guru :)… I’ve been experiencing issues with my ICC for the last few weeks, it would go black while driving, could not access anything, including AC, soft reboot did not work. The moment I stops it would go back! A technician came over and did hard reboot by disconnecting the 12V battery, one week later the ICC went completely down!!! I put another ticket, and now it’s been a week no one has called! Do you think this something has to do with the fuse box?
Thanks! With that description, I think you may need the ICC module replaced. I would check to see if a fuse is blown. Check out the Facebook "Fisker Ocean Maintenance and Tips" group, lots of good stuff in there. We already have a service manual available to download.
Hi Matt or anyone else on this comments thread…
Has anyone experienced a blank infotainment screen that doesn’t return to normal ops and stay blank. I have attempted multiple soft resets (on the steering column wheel) which results in the FISKER OCEAN startup log (10:27 in the video) coming up on infotainment screen then it goes away and stays blank. Anyways, looks like the infotainment screen is no longer operational (stays blank). Does anyone know if in need to reset a fuse or something?
If you see an image on the center screen during boot, the fuse is fine. If the screen is always blank, that would probably be the fuse. I'm not sure what is causing your issue. If you put the car in reverse gear, does the rear camera show up on the screen? Have you also done a deep sleep reset?
@@MTNRanger Yes, I did attempt a deep sleep rest and it hadn't resolved the issue (also the rear camera did show on the infotainment screen while in reverse but that was the only thing that worked with the blank infotainment screen; additionally all the drowsy driver warning started to appear as well while driving and the infotainment screen was inop). At about 8-10 hrs later after I initiated the deep sleep reset,, the problem went away. here's the resolution: I was lucky to get Brandon from Platinum Precision (former Fisker Tech) from the DMV area to help me with the issue. I happen to have an appointment with Brandon the very next day to get my water pump replaced and opt'd to get the 2.2 uploaded as well. He was able to do a hard reset on the center console but only after the HVAC controls came up. This happened only after about 8-10 hrs after I initiated the deep sleep (FYI: immediately after the deep sleep was entered about 2 hours after initiating the deep sleep, I still didn't have the HVAC control come up nor did the infotainment screen recover either) and btw, my vehicle initiated charging at 8Amps as well. I have been checking couple times since the issue was resolved while Brandon was at my location and it seems to be stable still. I'm glad that Brandon was able to reset the infotainment panel thru the switchology of the HVAC. Figures crossed (for now) that the center infotainment console would stay operational.🤔 The Switchology to do the hard reset was the following (if you are lucky to recover the HVAC controls (after a deep sleep reset) without of course the infotainment central screen up and running): set Driver Side Air temp to Highest possible setting (i.e. highest temp), then set the PAX side temp to the Lowest possible setting (lowest temp), then set fan speed to 7, and then activate the Rear Defrost. It immediately cycled the power to the Infotainment Center Console (by itself) with the Fisker Logo coming on and after a few mins, recovered my infotainment screen. Thanks to Brandon for helping me dodge having to replace the very $$$ ICC (for now).
@@OCEAN1Neelam Very interesting, I'll have to keep that in mind!
Thank you very much!
Since update 2.1, i don’t have the image from the front and rear cameras on my central screen when i park. Is it possible that this is due to a fuse ?
Thanks again
@@vetomania it most likely sounds like a module didn’t update. There are fuses for them. I’ll need to look it up and post.
Excellent! Thank you so much for posting.
Brilliant video. Now what about the passenger lights in the back turning on every 3 seconds...
I cover that in this video: ua-cam.com/video/Jawk2kphI8E/v-deo.html I am working on an alternative where you can still use the lights, but only controlled by the overhead console buttons.
@@MTNRanger oh man. If you do that, I'll be so happy. I look forward to your genius instructions
Would you please post the part number or specifics of fuse extension/ cut off that you used?
Thank you
All the parts used are listed in the video description. Here is the 30 cm version of the bypass extension: amzn.to/3Qm5up0
Great video. I'm thinking of installing the extender. What was the length of the extended you used? 30 cm?
I used the 60 cm, but 30 cm is all you really need. The 30 cm was out of stock when I was planning this video.
Once again, thank you for this video. I followed it as I installed my switch and it woks like a charm. 🎉 Now i have to wach the 12 v battery one, since i keep getting the warning, blocks me from putting it in reverse and when I restart it goes away. So I’m not sure it’s really the battery or just more garbage warnings. 😮
Sometimes there are just weird warnings. I reset usually fixes most of them. Though they can be exasperated by a low 12V battery voltage.
My driver door NFC is not working , and handle LED is not glowing and trunk cannot be open by button located on driver's door, is Toolbox have those settings ? your help is much appreciated
No, the Tbox fuse does not affect the NFC/PKC/locking/unlocking. I'm still not sure which fuse covers that.
Do you know which fuse controls the loud spaceship noise? Thanks for the video!
I have seen fuses for the siren and the horn, but I haven't found a fuse specifically yet. Eventually, I'll do a video showing how to disconnect the PWS speaker. It's on my to-do list.
Hi,
unfortunatelly for me pulling out 15Amp or the 5Amp fuse did not work. Pulling 5Amp fuse doesn't even turn off navigation.
Did you pull both out at the same time? The screen should turn off if you pull the 15 A fuse.
I think I know the answer to this. All was going great with my Ocean and, all of a sudden, I see Spotify, Iheart, etc. but none of them load. I am thinking I need to do a t-box reset. I could pull the fuse and reinsert, which I will probably do and if it works here are my 2 questions. Do you believe it's possible that I need to do a t-box reset to get those audio programs working. By the way I can still play spotify, iHeart, etc via my phone connected to the Ocean with bluetooth. And second question. Which of the Fuse Bypass Switch/Extenders did you buy? The 30cm or the 60cm in length? Great video which I probably knew I would need to access at some point. I am almost tempted to just leave things alone and use Bluetooth. My navigation seems ok, still wroking.
I personally have never had an issue with the apps not loading. Having them crash, yes, that does happen from time to time. I don't know if resetting the Tbox fuses will fix this. But I would still recommend trying it. You can use the 30cm length extender - I have in fact installed that one in another owner's car. I only used the longer one since it was the only one in stock.
I’m not at this moment in my inquiry, but definitely will if I get the numbers from manufacturer.
Gotta first see if they will start production and at what price per count etc 👍
Awesome, thanks for letting me know.
Thanks for this informative video. Looks like we need more of these to be able fix our wonderful vehicles our selves from the look of things.
Any suggestions on how to fix the cameras/blind spot lights permanently on issue? Can it be fixed with changing fuses?
Other question is if Ocean can work with Ottocast P3 OttoAIBox CarPlay Ai Media adaptor?
The cameras and blind spot detection issues are bugs that needed be addressed in software. Resetting fuses will not help that issue. No, an Ottocast P3 (or other device) will not work with the Ocean.
Which fuse controls the driver door side mirrors and buttons?
Cabin Fuse Box RF12
@@MTNRangerThank You, My LCA wasn’t working and I can’t get the mirror to move, the passenger mirror won’t close when I lock the car I’m guessing it’s a faulty fuse
@@Sploitheworld Yes, check that fuse. Let me know how it turns out.
Hey MTN Ranger. My car has no cellular or wifi connectivity since they attempted to push 2.2 to it. I tried your Tbox reset but it doesn't seem to have been effective. Any other advice for a case like this? Thank you!
So, 4G and Wifi worked before the attempted update? If so, you should contact FOA to see if there is something they need to do with any of the modules.
Thank you! I was able to add it and its resetting it. Question: My 4g signal shows 3 bars but its not getting any internet. Any clue?
I'm not sure if the issue lies in the Tbox or the ICC for this issue. You may need to have a tech check the modules to see if one is out of date.
@@MTNRanger Thank you!
Do all Oceans come with a hard copy operator/drivers manual?
No. The owners manual is on the center screen.
Hi Matt! Great video. Watched it when you first released it and hoped that it was merely for my entertainment. However, coming back from a trip to Detroit, I was listening to Spotify and wanted to change to TuneIn. At that point, the T-Mobile connection, according to the bars, was and still is gone. The radio still works, but none of the entertainment apps work either.
Oddly, TomTom still works but the lady has laryngitis. When I first start the TomTom in the morning, she comes on and tells the estimated time of arrival, but then goes silent. I suspect it is from being hooked up to the home WiFi. Judging by the radio audio, when a turn comes, the speakers at the front are attenuated and stay that way for about 10 minutes.
Do you think this issue is related to what you are describing in this video?
It's hard to say. I've never had the issue you describe. Sometimes things can be buggy and a deep sleep reset or overnight seems to fix them. Other times, pulling the fuse works. But what you describe sounds like either the ICC or Tbox. Pulling and resetting either or both fuses may help.
Any suggestions on how to fix the icc module or replace
Sorry, I don't have any experience with fixing or replacing the ICC module. I know it is located at the bottom of center console across from the Tbox.
@@MTNRanger what fuse is for the ICC controller. Resetting it may solve the ICC issue perhaps?
Just watched this and was wondering if I could apply this to my own situation. My Android will no longer work with the car. Calls come thru but voice is just static. Couple questions. 1) Do you know which fuse controls the phone/voice? Would it be the same fuse? 2) When taking the fuse out and waiting for a reset are you having the car on?
The RF22/55 fuses control the Tbox and ICC modules. When pulled also turns of the center display. I'm not sure if there is a specific fuse for the phone/voice. Yes, the car is on when you remove/reinsert the fuse (it's technically always on!)
Very helpful to the community. Are there any NON Facebook sites we should be aware of?
Since Fiskerati closed, the only other one I know of is Oceanforums.com. However, there is no centralized help section and until recently was a toxic site.
pulled out 15Amp, screen went off, but after re-inserting the fuse (more than a minute without fuse) - screen cme back up and navigation still frozen at home address
It's also possible you may have an issue with the ICC module (which communicates between the car and the network). Unfortunately, there may be more than one cause of the navigation locking up.
Hello, thank you for your video! My internet only works around 1% of the time and I’ve tried your method of resetting the Tbox by removing the RF55 and RF22 fuses, separately and together and have tried soft resetting but my internet works only for a couple minutes upon restarting the car and then goes away. I’ve also replaced both 15 Amp and 5 Amp fuses with new ones. Do you happen to have any other suggestions? Because of this problem my car is still stuck on 1.11
It sounds like you may have a problem with the ICC module (which controls communication). Either it needs a firmware update or be replaced. When did you get the car and where are you located?
Great video. May be you can help. My Dcc fast charger won’t work. It tries to connect to vehicle and then end up with “charging start error”. Do you know what fuse I could try to may be reset it! ? Thanks
Have you tried different CCS station? Some are not compatible (or giving issues) such as the EVgo 100kW stations. I'm not aware of which particular fuse controls charging.
@@MTNRanger thanks. Yea. Tried many different brands and locations too
@@sripavanv If that's the case, you definitely need Fisker service to look at it and see if there is a hardware problem.
Полезное видео для новых владельцев
Hello,
Thank you very much for the great video.
I am from Germany and have had my Fisker Ocean Extreme since December 2023.
There is no longer any support in Germany.
After Update 2.0 I have no longer a connection to the apps and the internet. Date, navigation and updates are no longer possible.
I tried to reboot the car using the main-switch near the battery. But that didn't work.
Do you think I can reactivate the navigation system and the internet connection by using your suggested method?
I would be very happy about a short answer.
Thank you and greetings Germany
Yes, it most likely sounds like you need a Tbox reset using this method.
@@MTNRanger
Thank you for your quick answer!
I'll try it tomorrow morning and I'll give you feedback.
Do you think I should remove both fuses at the same time or only one at a time andd step by step?
And you also think waiting for 1 minute might be enough?
I often read in German forums, that you should wait 10-30 minutes for other systems to restart.
Many greetings from Germany.
@@joergebenhoch You could remove both, but try RF22 first. Everything I have seen only requires about a minute before reinserting. It would not hurt to wait longer if you wish. In any case, I would do a infotainment reboot after you reinsert the fuse.
@@MTNRanger
Thank you :-) Is it sufficient if the Fisker is opened with the key or NFC? I don't have to press the brake pedal either? By restarting the infotainment you mean that I hold the two inner buttons on the steering wheel for 15 seconds?
@@joergebenhoch Opening method does not matter. You press the brake pedal to wake the car up or put it in ready mode. Yes, pressing the two inner buttons on the steering wheel.
MTN Ranger, My Center Infotainment Screen is inoperable - When starting up the FOO the OCEAN script and FISKER Logo appears, then the screen goes blank. Unfortunately, this TBox fix does not reset the main screen. Any ideas on which fuse this could be? Thanks for a great video here about reset of GPS and Navigation.
Sorry to hear about that. Did you get a vent replacement recently?
Hello, my 4g suddenly stopped and i vannot connect to any wifi. It started when parked for 6 hours. Only think i noticed was 12v battery did dip below 12v while parked. Normally it stays above 12v. Is this fuse pull a fix for 4g and wifi?
@@petertierney994 I can’t guarantee it, but the ICC does control the 4G. You may want to try removing/reinserting RF22 and/or 55.
@@MTNRanger is it possible the 12v battery monitor can prevent the car to sleep. Since I successfully installed it a few days ago I cannnot get the car to sleep. I also cannot get the energy saving modes to trigger. I want to do a deep sleep before I pull the fuse. Maybe I'll disconnect the monitor first. I know it uses power from 12v to send Bluetooth. Maybe this draw is keeping car alive on the version I have.
@@petertierney994 It may be possible, but I have not heard anyone bringing it up before. The huge number of modules in the car and their respective versions may cause different outcomes on different Oceans. Yes, I would test without the monitor to see if it goes back to the original functioning.
So it worked with just the one fuse pull, my wifi reconnected and I say the 4g flash before wifi. Will take for a spin to confirm 4g after I put car back together. Wifi always errors on connections unsuccessful but I see it connected on my router and the internet on the car works now.
Hi MTNranger, do you think it would be ok to not put back the first screw that you removed in the video or do you think the panel will fall off? It seems that the clips and the bottom screws were able to keep the plastic panel in place.
The side screw probably could be left off. For future access, this would save time.
I guess I have been lucky with my FOO in that I have not had a problem with the navigation location being stuck.
I do have the issue with Navigation updates not working, and the maps showing as 19 months old. I reached out to Tomtom and was told that they update the maps every 3 months. Lastly, for my navigation it shows states that I have never driven to as being "Region in Use". On my car it shows the state of Washington in Use and my car has not left California. I really hope that the Fisker 3.0 update includes working updates to the Fisker Ocean Navigation maps.
The maps download has never worked on the Ocean. They appear to download but never install and error out. The points of interest are very poor in the navigation. I search for local destinations and it sometimes points to something 500 miles away when I know there is one 5 miles away. Very odd.
How are you interior LEDs colored?
ua-cam.com/video/RLG2Pmi0uok/v-deo.html
This helps so much
Do you know which fuse to check for by any chance or I'll need to do a process of elimination
There are fuse box diagrams and legends in the owners manual. I found the two fuses marked TBOX and started from there.
@@MTNRanger I found it. Thank you. You are a great asset to our group. Continued success to you.
my goodness, so much for a readily avail fuse box like they used to have.
At least the other three are easier to get to.
Does that work for resetting the wifi connection
Yes, I think the WiFi goes through the Tbox.
Did you end up using the 30cm or 60cm bypass switch?
In the video I used the 60cm version. You really just need 30cm, but it was out of stock when I was planning the video.
Thanks!
My car is on 2.0 and Fisker replaced ADAS module to make cameras work but it has made lane keep assist and blind spot monitoring unavailable. Do you have any tricks or suggestions to get them working?
You got me on that one. I think the tech should have calibrated/updated all the modules when replacing the ADAS module. I'm not sure I can suggest anything on that, sorry. Are they totally not available or do them come and go?
@@MTNRanger thanks for the response. Unfortunately those 2 items are completely unavailable. It was becoming impossible to drive with notifications switching between blind spot monitoring unavailable and lane keep assist unavailable. So I had to set them to disabled. Even after doing that I get a reminder on each drive that both of those functions are unavailable. I wish Fisker was in better shape to help me by sending a tech to troubleshoot it further. I have now given up hope on getting it working.
Thanks for sharing. Awesome job. You are not even wearing glasses.
@@chealay7251 I need them for distance.
Thanks for sharing
Used this to successfully reset my Tbox and 4G service.
Thanks for the video. I hope I never have to do this. Seems way complicated to access a fuse panel.
Yes, the other fuse boxes are easy. This one was almost intentionally designed to be hard to access.
Great job
Major design flaw having to do all this to access the fuse box. 😢
If you can do this, you can probably help with this?
You'll be my hero if you can figure out how to make the reverse and below 23mph forward speaker sound not as loud or a way to 'legally' shut it off.
Yes, there is a way to disconnect the pedestrian speaker. Thanks for the suggestion. I have not done it yet and I'll put it on my to-do list!
Ok, tonight I tested with the key fob in the console and I got 30 minutes of run time before the outlet turned off. Not quite as good as in the video, but still sufficient many outlet uses. You can press the brake pedal and start another 30 minutes of use.
@@MTNRanger you rock! Thanks. and maybe there's a way to muffle the sound so it's still on, road legal, but not as annoying. Can't tell you how much I appreciate your videos!
Thanks. It is really sad that we paid $50k plus for a car that we need to do this to in order to work.
My GPS has worked all of 5 minutes since December. This is a lot of work and potential damaging of panels and clips. I may call for a technician instead.
Yes, ideally if you can get service to do it, that would be preferred.
The fact that a fuse reset switch is needed is troublesome. Shouldn't bugs requiring reboot be solved BEFORE mass production.
Yes, ideally that would happen. But we may soon be one our own with regard to keeping the Ocean serviced and maintained.
My Brother, WHY is our 🐟 UPSIDE-DOWN? 😂
Mine isn't.
I appreciate the video. But I have to wonder how often does a problem occur where you have to pull one of these fuses to reset the Tbox? Seems like a ridiculous amount of effort and expense for an owner to make their own tweaks to the vehicle to keep it working. Which leads me to think that this car has some pretty horrible electronics engineering design. Knock on wood, I have a FOE purchased in December, currently on 2.0, and I don't "think" I have any Tbox issues.
Some people have the Tbox lockup every week, others may not have the issue. I think given enough time, these problems would have been addressed by the company. Most are probably fixed with OTA software updates to the system. It's unfortunate that the owners have to do this, but with the company going away, there is no other choice.
it's so scary how this car is put together. A fuse box must be easily accessible. It shouldn't be necessary to take the car apart like that. What a piece of shit
yes, both the battery and the fuse box access is really strange considering that everything is electric.