I prefer to use plastic tools for scraping the deck, so as not to scratch the paint, encouraging rust. The tools used for auto bodywork, spreading Bondo, work well.
I found that vinegar in a spray bottle is a pretty good solvent for loosening the caked-on grass. As you scrape with tools, spray the vinegar periodically and let it soak on. These tools worked well for me: Pry bar for scraping, a MoJack scraper made for mowers (from the company that makes mower lifts), chisel with hammer (used sparingly, wire brush and a good portable light. Essential: Dust mask and wraparound goggles. I used a mower lift. Take the blades off! The job would have been easier with the deck removed, but I didn’t want to take that on. It’s hard work. Took me an hour and a half. Last: Spray with PAM spray for pans to discourage grass from sticking.
I have a John Deere Z930M. I lock the deck in the highest position and slide a high pressure rotating pulsating water sprinkler underneath each open area. About 5 minutes on each side of the mowing deck and the deck is sparkling clean after each mowing. Then I run the blades for a few minutes to dry it out and park it ready for the next mowing. I just blow the top of the deck off with a compressor and try not to wet that area down. I'm just lazy. This was an informative video.
Great video! I recently bought a home and personally enjoy mowing the lawn. As a beginner lawn care person I'm learning along the way which is why I'm looking for videos like this even though on a much larger scale than I have it still helps me. I have a walk behind self propelled mower. Is there any way to clean it down to the paint? A special cleaner? I'd like to apply a coating to the deck so it's easier to remove the grass but I have to apply it to a clean deck. Thank you again and appreciate anyone's thoughts and ideas.
While you have the belt off, rest your hand on top of the deck and spin the blades one at a time. If the deck is smooth you're ok. If the deck vibrates like you are driving on gravel, the bearings in that spindle are crap. Replace them now.
I'm wondering why a " professional " let their deck get that dirty to begin with. It obviously hadn't been cleaned for a few days. Clean it every day when you sharpen your blades.
More like a few months. Never could understand why people would spend hundreds or even thousands of dollars for lawn equipment and never clean it or half way clean it. You wouldn't half way clean your car, would you?
Don't care much fir zero turn radius mowers, to me, they are a severe accident ready to happen, seen people flip themselves out of those things, besides, all you can do with them is mow grass, can't plow snow, can't plow the ground, can't disk your ground nir cultivate your garden with them. RATHER HAVE A TRACTOR!
I prefer to use plastic tools for scraping the deck, so as not to scratch the paint, encouraging rust. The tools used for auto bodywork, spreading Bondo, work well.
I found that vinegar in a spray bottle is a pretty good solvent for loosening the caked-on grass. As you scrape with tools, spray the vinegar periodically and let it soak on. These tools worked well for me: Pry bar for scraping, a MoJack scraper made for mowers (from the company that makes mower lifts), chisel with hammer (used sparingly, wire brush and a good portable light. Essential: Dust mask and wraparound goggles. I used a mower lift. Take the blades off! The job would have been easier with the deck removed, but I didn’t want to take that on. It’s hard work. Took me an hour and a half. Last: Spray with PAM spray for pans to discourage grass from sticking.
Wait. Jacked up 12”, but mower was nearly stood on it ass when he cleaned it. Did I miss a magic step?
I have a John Deere Z930M. I lock the deck in the highest position and slide a high pressure rotating pulsating water sprinkler underneath each open area. About 5 minutes on each side of the mowing deck and the deck is sparkling clean after each mowing. Then I run the blades for a few minutes to dry it out and park it ready for the next mowing. I just blow the top of the deck off with a compressor and try not to wet that area down. I'm just lazy. This was an informative video.
You'll probably end up rusting the deck
High pressure can damage the spindles. Bad idea
Great video! I recently bought a home and personally enjoy mowing the lawn. As a beginner lawn care person I'm learning along the way which is why I'm looking for videos like this even though on a much larger scale than I have it still helps me. I have a walk behind self propelled mower. Is there any way to clean it down to the paint? A special cleaner? I'd like to apply a coating to the deck so it's easier to remove the grass but I have to apply it to a clean deck. Thank you again and appreciate anyone's thoughts and ideas.
Great instructor!
Should you disconnect the battery first?
While you have the belt off, rest your hand on top of the deck and spin the blades one at a time. If the deck is smooth you're ok. If the deck vibrates like you are driving on gravel, the bearings in that spindle are crap. Replace them now.
Good video and tips! Thanks
right on
keeps the rust from developing, too
Great video, well detailed!
except for how to get the deck into the position for cleaning
Even with everything off, and the key not in ignition. I am afraid to clean it. 😅 is it completely safe to do so?
You should be good if you follow the instructions.
Mine will never look like that. I clean and repaint mine after each use or every month.
Good video. Thanks
I think you meant baffles, not bevels.
My Gravely states Do not lift by the deck. Just saying...
Is this the guy from epic meal time ?
What causes the mold to grow at the bottom deck
moisture
Is that you Sauce Boss ?!??
CHOCKS, not chucks.
I'm wondering why a " professional " let their deck get that dirty to begin with. It obviously hadn't been cleaned for a few days. Clean it every day when you sharpen your blades.
More like a few months. Never could understand why people would spend hundreds or even thousands of dollars for lawn equipment and never clean it or half way clean it. You wouldn't half way clean your car, would you?
Are yall joking? A few months? Guess you've never mowed when its wet. 10 yards can do that in a day.
one thing he didn't mention is take out your spark plug just for extra safety precautions when cleaning under the deck
Agreed. As accidents do happen. Remember, safety has no quitting time.
Who's jack ?
How is it you look exactly like a mower mechanic
Not so easy on a zero turn lying on your back.
If you got a lawn mower lift makes it much easier
That's a lot of grass.. I bet the mower works better now.
ChOcks not chUcks
Rochester accent?
Isiiaooa
Dirt ain’t gonna hurt ya. I love it! This is for all you pansies out there.
2 words Pressure Washer
Water gets in the bearings, terrible advice.
Don't care much fir zero turn radius mowers, to me, they are a severe accident ready to happen, seen people flip themselves out of those things, besides, all you can do with them is mow grass, can't plow snow, can't plow the ground, can't disk your ground nir cultivate your garden with them. RATHER HAVE A TRACTOR!
Dan Basta lol you can do all of those things with a zero turn.
For me it was speed + manoeuvrability, pretty much twice as fast if you're just mowing lawns.
Other option is just to have both 😂
Can you imagine using a tractor to run a lawn maintenance company? 😂