Even 10 years ago, if you had told me I’d have all this at my fingertips, I wouldn’t have believed you. Now I take it for granted. Sometimes there are almost too many options! But I’ll never complain.
just saw this 2 hours after you uploaded it. Coincidentally I was charging my E530. Immediately added the 2 CiQ apps for my device and have configured it for the map and climbpro page. Thanks! 🙂.
Have you used it? I added today (on my Edge 530) and found the 4 data fields too small to be useful. Also looks like it cuts a bit off? Only have two brief climbs to test on round here.
@@cmarnold78 Yes, used the edge 530 this morning. I had both apps installed and configured on my map screen which presented 4 fields in total. (HR, Power, Grade, elevation). The text is certainly smaller but I can still read it. I did not notice that it cut anything off. It's actually slightly easier to read than the map dashboard app.
@@davidh7414 Worked it out this morning - OK - So for Edge 530 there is a bit more work to get this working not covered in the video. You need to have both Map Fields & Map Fields #2 installed BUT you still need to have 4 fields selected for each one. You have to work out which field appears on the screen. Example if you have Edge Maps on the Left and Edge Maps #2 on the right the fields that will display for Edge Maps are Left Upper Field and Left Lower field. For Edge Maps # it will be Left upper field and Left bottom field that will actually appear. You have to put in different dummy fields for the right upper and lower fields for both. Its a bit confusing so easy to note on paper on a grid to start.
I never used to leave climb pro on, always going back to my main data setup. But this changes that, I can see what I need to while climbing, then revert back to main data screen when the climb is done. Very useful, thanks for sharing this.
An extra big thumbs up. I have so wanted a more configurable Climbpro and the 2 data fields just wasn't enough. I found it so frustrating I switched the Climbpro pop-up off. I will certainly now go back to using it again given this added functionality. I agree too that Windpro is also a great data field to have. Thanks
I know the feeling - I just had my first ride yesterday wearing varifocals - it was revelation - I could see where I was going and also read my Garmin 😂
Love seeing your love affair with Windfield continue Shane, and i will be putting this setup straight onto my 1040. There's a huge number of fields available via windfield so you can get a really varied config with these two combined.
It's just so damn handy. With the maps on screen too you can see exactly what's going on. I keep looking at my car console/GPS for the wind direction now too. 🤣
All - with the most recent Garmin update, you can now DOUBLE the visible data - therefore on climbpro for Garmin 530/ 830 devices for example, 8 data fields are available now, and not just 4. Sweet!
That explains why 4 data points showed, instead of the two that this video says. However, with four in each box, they are too small to read. Any idea how we can get back to two per data box? I can't figure out how to do that in Settings.
Thank you Shane!!! Your advice on how to navigate the Garmin is a Godsend. I am not a techie so my frustration level on set up on the 540 was becoming more than frustrating until I saw your videos. Again Thank you for such a thorough and easy to follow paths.
Great video, I have just installed the app on my Edge 1030 Plus with easy to follow instructions. I do not seem to be able to get the Windfield app to appear on my map screen as per your video. I will be doing a test run soon to check it out. Thanks Shane.
Shane, I was confused on the 840 limitation of showing only two fields. I kept watching the video. I should know better than to think you wouldn't have all the bases covered. Thanks again for the content.
Who else finds climpro a torture instrument? When I am in agony on a climb I rather not know how many Km and what gradient is ahead. Seing the slow progress and the remaining hell ahead just rises my anxiety. I used it for a while and then hid it as a secondary screen. Just dealing with what's ahead of me gives me peace of mind. 😂
Wahoo doesnt need this, because there is much more datafields on bottom of every special page, even on smaller screen! Garmin with its large screens can show all important values but they dont! Garmin is just overrated beacause it has a lot of unnecessary functions, but at same time it cant do few most important functions! Wahoo is much much reliable than Garmin!
OK - So for Edge 530 there is a bit more work to get this working not covered in the video. You need to have both Map Fields & Map Fields #2 installed BUT you still need to have 4 fields selected for each one. You have to work out which field appears on the screen. Example if you have Edge Maps on the Left and Edge Maps #2 on the right the fields that will display for Edge Maps are Left Upper Field and Left Lower field. For Edge Maps # it will be Left upper field and Left bottom field that will actually appear. You have to put in different dummy fields for the right upper and lower fields for both. Its a bit confusing so easy to note on paper on a grid to start.
@@jonethernandez3365 You need to have it downloaded and running as a course on navigation for it to work (for 530) I think on the 540 you don't need to have a route running.
@@jonethernandez3365 You need to import a route/course as a .GPX or other (eg in Strava/Kamoot/MapMyRide) into Garmin Connect then send it to your Edge, then start the course.
Is that the GoPro Max or Insta360? This ConnectIQ field is amazing! The ingenuity of people simply mind blowing. Garmin should take notice Edit: I should have finished watching the video before posting 😂
Try removing all IQapps en test one by one. You probably have an app that crashes all the IQapps, this way you can identify which one causes the crash.
Incredible Garmin don't let customize climb pro screen as you want. I don't want the map for example in the climb pro screen but I can't erase it. Incredible as poor developing. Maybe I only want know how many meters remain, make this values data fields and I choose the ones I like, Garmin.
@@UloPe Please write it, say it everywhere (im doing it), because Garmin is selling milions of that shitty units and that is only problem why they dont need to be more professional. All reviews are too much positive and dont telling the truth about how big shit Garmin is! - because of that i bought that shit!
@@CrustySVK yeah I’m definitely mentioning it whenever I talk about it. I do feel I got what I wanted out of the edge compared to the Bolt (namely better/faster navigation) but all the other stuff really is annoying.
I am finding that as I get older smaller print is not a good thing! I would need a really BIG screen to add all those data fields and still be able to read them! Cool feature though.
My climb pro (edge 830) doesn't show the map (looks like the device in the screen in min 4:00). Can someone here tell me how I can get it display the map above the elevation profile as seen in this video, or is not possible in the edge x30?
Great video, thanks Shane. Are you able to explain the significance of the black and blue bars that appear beneath the climb profile? Might just be on long climbs
I'd think if you're that concerned with climb performance you'd just bugger off the map for that section? It seems unlikely you'll get lost while pumping your climb segment and it's taking up a massive amount of the screen.
Hi, I have a Edge 1030 Plus. Is it possible to have the screen like you, the map in first floor and the climb in the middle of the screen? Thanks a lot
The iGS800 is simply not ready for release. There's so many things wrong with it they needed to spend another six months fixing things before launching. There's some unfixable hardware issues too. The review will be out sometime soon. It's not great.
Thanks Shane, very informative. However, when i go through the rpocess i always get a repeat of the same data on the left and right.....or a singe data fieldc on one side and 2 on the other....any thoughts form anyone???
I'm still using my trusty 1030. I don't see an option in the ride profiles to keep ClimbPro active (keep screen on head unit) while on the climb. I get the ClimbPro screen, but it keeps scrolling through my other screens. I've been tempted to pull the trigger on a 1040 and keep telling myself it will have better features, but the cheapskate in me wants to wait for the 1050!
Hey Shane, thanks for the tips to finally have all the data in view during the climb. Do you know how to set the Edge 1040 to show the route above the gradient line in the Climb Pro data field during navigation? It only does this for me in Free Climb Pro. Thanks in advance!
@@gplama i was about to ask the same question, but i own a 1030 plus, and i cant find that. And it buggers me when climb pro takes over before a crossroad and i did not see which way i gotta go.
Great tip, thank you! Quick question: can you use the ClimbPro feature on the Edge 1040 while doing e.g. a triathlon? My ideal setup would be to just set the Edge 1040 into Extended Display mode, have the .gpx file loaded and guiding me on the bike course, and still see the ClimbPro data. Is this possible?
@shane Miller the problem is that there is 2 behavior on climb pro. One on free ride ( imo the best one as you can still see the map) and another behavior when you are following a course. That one is very very annoying as it maks the map by a pop-up and replace with what we see on the right at 3:30. It’s happened multiple times that on a descendant just before another climb with 2 or 3 different roads the climb pro pops up …and you don’t see the map anymore!,, 2 solutions or stop and change screen on the edge to come back on the map ….or to gess the road….. very annoying as I said. Why Garmin do not introduce a switch On/off function for this?
Hello GPLama,maybe different topic… Is there any way how to see waterpoints on the map allways? I know there is a function navigate to waterpoint,but on themap I can see pointless carpark poi.What I found on the internet looks quite difficult to me toget ist displayed as waterpoint poi. Thank you very much Tom
I like the look of this data screen, but I can't figure out how to change mine on 1040 to show a map and that style elevation profile... Only the bottom 2 fields are editable, the top 2 are seemingly stuck on the large "are we there yet" field, and a large elevation profile that shows no other data.
Same here on my Edge 1040 Solar. At the top, he has the navigation map, but I don't. I have a huge Distance To Go and Ascension Remaining which takes up far too much valuable space. How do you get these replace by the navigation map ?
Hi shane, on my edge 840 I do have climb pro anabled. In the setting the ‘show screen’ and ‘pop-up’ option are enabled as well. The problem I get, is when navigating, the climb pro screen Pops up but then the map and navigation is gone…. On your screen the climb pro is beneath the map, but that option i cannot find…. Did I do something wrong? Did I miss something? Thx considerabel :) ! Love your content!
very nice thanks for sharing, just installed. however I fail to configure my ClimbPro screen on my Edge 840 the way you have it set up at 0:12 on your 840 solar. The only option I have is the layout you have at 3:47. how can I change that?
is there a way to get rid of the MAP at the top. I find it completely useless as I'm going slow enough up a hill to see where I'm going. All I want is the colour gradient chart and a few other bits of info - speed HR Cadence etc on screen and large enough for my 65 year old eyes to see. I have the Edge 840. Any thoughts?
@@gplama my map disappear even on the 1040 when I have selected and riding a course. Is there a workaround? Sometimes it happens that our group are leaving the course in Front of a Climb without knowing because we loose Information about the track when climb pro pops up
When I installed and configured this on my 840, it actually did put 4 data points in each of the two data boxes. Those were too small to read, and I could not figure out how to reduce the number to two for each data box. Any advice?
Hi, I cannot find "Mapfields" but there is a Mapfields #1 . What's the difference between Mapfields #1 , Mapfields #2, Mapfields #3 ? Which one should I install on a 1050 ?
Somehow my 1050 let me put 4 total data fields on climb pro, but only when I do it on my edge not via the app. Haven’t tested it but it seems to be working based on the preview.
I can get the screen with the map, climbpro and the data fields while riding without following a course. If I ride on a course, I cannot get the combined screen, I only get the map and the data fields. Am I missing a setup somewhere? I could not find this information watching the video many times.
Ok, I got the four small fields set up. But, how do you get the route map to show above the climb profile? I can't seem to change the Climb Pro current upper display of Dist to Go, Asc. Remain and Grade Remain.
@@gplama Ah, I have a 840 Solar. Sometimes I miss a route turn because Climb Pro jumped up. I thought you might have had another app running to get the map display above the climb profile. Thank you for all the great videos.
2:07 Garmin Connect IQ App, go to the settings for the data field and tap each field ex. Upper right/left, etc. It gives you the option to replace each one
Hi Shane, do you know of anyway (on an Edge Explore2) to increase the size of blue location arrow and the history line on the map? I just find them too small, regards from Italy (escaping Ballarat’s winter) !
It is great that we have those custom field apps, but is it possible to disable this stupid "Climb starting" countdown? It drives me nuts that I can't see my power anymore unless I tap on this. And then this useless "Climb!" green box that appears for too long as well. What are those for, for people that want to measure their climb performance progression on local climbs or what?
So does free ride for climb pro work on a 1030 edge +? My standard climb pro comes up if I scroll through the pages, it doesn’t come up automatically but map fields doesn’t come up at all?
Still in progress. As I've replied to someone else here already tonight - The iGS800 is simply not ready for release. There's so many things wrong with it they needed to spend another six months fixing things before launching. There's some unfixable hardware issues too. The review will be out sometime soon. It's not great.
@@windfieldapp i think its the bike computer not having a consistent view of North rather than the 3rd party data )mpt your datafield, I use a different one)
Even 10 years ago, if you had told me I’d have all this at my fingertips, I wouldn’t have believed you. Now I take it for granted. Sometimes there are almost too many options! But I’ll never complain.
just saw this 2 hours after you uploaded it. Coincidentally I was charging my E530. Immediately added the 2 CiQ apps for my device and have configured it for the map and climbpro page. Thanks! 🙂.
Have you used it? I added today (on my Edge 530) and found the 4 data fields too small to be useful. Also looks like it cuts a bit off? Only have two brief climbs to test on round here.
@@cmarnold78 Yes, used the edge 530 this morning. I had both apps installed and configured on my map screen which presented 4 fields in total. (HR, Power, Grade, elevation). The text is certainly smaller but I can still read it. I did not notice that it cut anything off. It's actually slightly easier to read than the map dashboard app.
@@davidh7414 Worked it out this morning - OK - So for Edge 530 there is a bit more work to get this working not covered in the video. You need to have both Map Fields & Map Fields #2 installed BUT you still need to have 4 fields selected for each one. You have to work out which field appears on the screen. Example if you have Edge Maps on the Left and Edge Maps #2 on the right the fields that will display for Edge Maps are Left Upper Field and Left Lower field. For Edge Maps # it will be Left upper field and Left bottom field that will actually appear. You have to put in different dummy fields for the right upper and lower fields for both. Its a bit confusing so easy to note on paper on a grid to start.
I never used to leave climb pro on, always going back to my main data setup. But this changes that, I can see what I need to while climbing, then revert back to main data screen when the climb is done. Very useful, thanks for sharing this.
An extra big thumbs up. I have so wanted a more configurable Climbpro and the 2 data fields just wasn't enough. I found it so frustrating I switched the Climbpro pop-up off. I will certainly now go back to using it again given this added functionality. I agree too that Windpro is also a great data field to have. Thanks
Excellent. Now I just need my reading glasses as I ride. I can't wait to try this on my 840. 👍🏻
I know the feeling - I just had my first ride yesterday wearing varifocals - it was revelation - I could see where I was going and also read my Garmin 😂
I had to get sport sunglasses with reader lenses this year. Tifosi makes a few cycling specific reader options. I love them!
@@andrewcollie Yep - get the biggest Garmin device and some bi or varifocals...game-changer. Without them maps are totally useless!
lol😆
Tried this on my 840.. Worked Fantastic.
Love seeing your love affair with Windfield continue Shane, and i will be putting this setup straight onto my 1040. There's a huge number of fields available via windfield so you can get a really varied config with these two combined.
It's just so damn handy. With the maps on screen too you can see exactly what's going on. I keep looking at my car console/GPS for the wind direction now too. 🤣
@@gplama wait a tic. that would be a great idea for electric cars since headwind/tailwind really changes the range. hmmmm
Excellent, thanks - I see there are now four configurable MapFields. Also great to add to the Map screen.
Been using MapFields / #2 on my 540 for a month or so now. Very handy on those screens where it is fixed to two fields.
All - with the most recent Garmin update, you can now DOUBLE the visible data - therefore on climbpro for Garmin 530/ 830 devices for example, 8 data fields are available now, and not just 4.
Sweet!
That explains why 4 data points showed, instead of the two that this video says. However, with four in each box, they are too small to read. Any idea how we can get back to two per data box? I can't figure out how to do that in Settings.
@@Dunc2222 Good point regarding changing back 2, not sure I am afraid !
Thanks, just added this to my climb pro screen, I’ll try it on my next ride
Let me know how it goes. 👌🏼
Thank you Shane!!! Your advice on how to navigate the Garmin is a Godsend.
I am not a techie so my frustration level on set up on the 540 was becoming more than frustrating until I saw your videos.
Again Thank you for such a thorough and easy to follow paths.
Thanks for this, helped me get my Climbpro configured.
Extremely informative and useful as always ✊🏾👊🏾 Thank you 🙏🏾
Great video, I have just installed the app on my Edge 1030 Plus with easy to follow instructions. I do not seem to be able to get the Windfield app to appear on my map screen as per your video. I will be doing a test run soon to check it out. Thanks Shane.
Shane, I was confused on the 840 limitation of showing only two fields.
I kept watching the video. I should know better than to think you wouldn't have all the bases covered.
Thanks again for the content.
Great info! Thank you for your channel. I’m a newbie and your content has been so resourceful.
Who else finds climpro a torture instrument? When I am in agony on a climb I rather not know how many Km and what gradient is ahead. Seing the slow progress and the remaining hell ahead just rises my anxiety. I used it for a while and then hid it as a secondary screen. Just dealing with what's ahead of me gives me peace of mind. 😂
Cycling wasn’t meant to be easy. If it was, Garmin would release CouchPro! 😉
Someone said, "Cycling doesn't get easier, you just go faster."
excellent!!! it works well thanks for the tip
in the meanwhile, garmin added support for more fields on the screen (in sets of 2), atleast for the 1050
Great vid BUT how did you get the map to show at the top as my 1040 climb Pro takes up the entire screen? thanks
Any luck?
You have to install the latest beta (24.11)
Amazing. Not sure if this type of video could be done also for Wahoo. Thanks for the content 🎉
Wahoo doesnt need this, because there is much more datafields on bottom of every special page, even on smaller screen! Garmin with its large screens can show all important values but they dont! Garmin is just overrated beacause it has a lot of unnecessary functions, but at same time it cant do few most important functions! Wahoo is much much reliable than Garmin!
nice feature, but guess will have to take my reading glasses on tour then for my 840 ...
Super useful, thanks!!
Love this stuff!
Would be nice to see tips to make something similiar for element bolt 😄
OK - So for Edge 530 there is a bit more work to get this working not covered in the video. You need to have both Map Fields & Map Fields #2 installed BUT you still need to have 4 fields selected for each one. You have to work out which field appears on the screen. Example if you have Edge Maps on the Left and Edge Maps #2 on the right the fields that will display for Edge Maps are Left Upper Field and Left Lower field. For Edge Maps # it will be Left upper field and Left bottom field that will actually appear. You have to put in different dummy fields for the right upper and lower fields for both. Its a bit confusing so easy to note on paper on a grid to start.
Hi. Question. Do I need to have the Edge Mapfields to make work? I haven’t able to make my ClimbPro works
@@jonethernandez3365 You need to have it downloaded and running as a course on navigation for it to work (for 530) I think on the 540 you don't need to have a route running.
@@cmarnold78 Sorry. Can you explain me how to do that please. I add as screen on my Garmin, but when approaching a climb doesn’t do anything.
@@jonethernandez3365 You need to import a route/course as a .GPX or other (eg in Strava/Kamoot/MapMyRide) into Garmin Connect then send it to your Edge, then start the course.
@@cmarnold78 Thank you. 🙏🏼
Thank you, this is very good. lets see if it works now
I LOVE your content!
Now if I could only upgrade my vision.... getting old sucks. ;-)
Not getting old sucks more !
Thanks excellent. Tho my eyes may find seeing the 4 data fields a challenge hahahahaha
Is that the GoPro Max or Insta360?
This ConnectIQ field is amazing! The ingenuity of people simply mind blowing. Garmin should take notice
Edit: I should have finished watching the video before posting 😂
Another really useful video but the ConnectIQ apps on my 1030 Plus crash on pretty much every ride now so I probably won't bother.
Try removing all IQapps en test one by one. You probably have an app that crashes all the IQapps, this way you can identify which one causes the crash.
Thanks for sharing.
Incredible Garmin don't let customize climb pro screen as you want. I don't want the map for example in the climb pro screen but I can't erase it. Incredible as poor developing. Maybe I only want know how many meters remain, make this values data fields and I choose the ones I like, Garmin.
That’s the big problem with garmin, nothing is finished, everything is in a half assed „good enough“ state…
@@UloPe Please write it, say it everywhere (im doing it), because Garmin is selling milions of that shitty units and that is only problem why they dont need to be more professional. All reviews are too much positive and dont telling the truth about how big shit Garmin is! - because of that i bought that shit!
@@CrustySVK yeah I’m definitely mentioning it whenever I talk about it.
I do feel I got what I wanted out of the edge compared to the Bolt (namely better/faster navigation) but all the other stuff really is annoying.
great content!
I am finding that as I get older smaller print is not a good thing! I would need a really BIG screen to add all those data fields and still be able to read them! Cool feature though.
My climb pro (edge 830) doesn't show the map (looks like the device in the screen in min 4:00). Can someone here tell me how I can get it display the map above the elevation profile as seen in this video, or is not possible in the edge x30?
Great video, thanks Shane. Are you able to explain the significance of the black and blue bars that appear beneath the climb profile? Might just be on long climbs
show, excelente dica.
I'd think if you're that concerned with climb performance you'd just bugger off the map for that section? It seems unlikely you'll get lost while pumping your climb segment and it's taking up a massive amount of the screen.
Thanks for another really useful video!
Question: what software are you using to create the PIP with your 360 footage?
Final Cut Pro for the video editing/production.
How are you showing map / route on top, is that because you "came" from the map screen, when the climb started ?
same question here
I want to know how to get rid is the map from this screen
I've got the Edge Explore 2, how do you set ClimbPro to have the map at the top of the screen?
Same question here.
Hi, I have a Edge 1030 Plus. Is it possible to have the screen like you, the map in first floor and the climb in the middle of the screen? Thanks a lot
i never see the the map during climb pro on my 1040. how come?
Maybe you need to have navigation active? But I think I recently had navigation on and map disappeared.
Latest beta
How do you do to put the map at the top (and remove dist to go and ascend remain)
Thank you, I was hoping this might work on my 830 but can’t seem to get it to work 😩, Karoo 3 on its way soon anyway
Hi Shane. Will we be seeing a full review of the iGPSport iGS800 GPS Cycling Computer anytime soon? Looking forward to it. Thanks.
The iGS800 is simply not ready for release. There's so many things wrong with it they needed to spend another six months fixing things before launching. There's some unfixable hardware issues too. The review will be out sometime soon. It's not great.
@@gplama Ok... Thanks Shane! Appreciate the reply.
Quite a lot of Garmin Edge 1040 content this month. Sounds to me like it is being compared to something very similar.
Thanks Shane, very informative.
However, when i go through the rpocess i always get a repeat of the same data on the left and right.....or a singe data fieldc on one side and 2 on the other....any thoughts form anyone???
Hmm... Might be one for the developer to answer. I'm not sure.
I'm still using my trusty 1030. I don't see an option in the ride profiles to keep ClimbPro active (keep screen on head unit) while on the climb. I get the ClimbPro screen, but it keeps scrolling through my other screens. I've been tempted to pull the trigger on a 1040 and keep telling myself it will have better features, but the cheapskate in me wants to wait for the 1050!
Hey Shane,
thanks for the tips to finally have all the data in view during the climb. Do you know how to set the Edge 1040 to show the route above the gradient line in the Climb Pro data field during navigation? It only does this for me in Free Climb Pro.
Thanks in advance!
Is there a way to display both climb pro and map fields at the same time on my edge 530 ? I cannot find the option in the settings.
Possibly only an option on the larger 1040 units.
@@gplama i was about to ask the same question, but i own a 1030 plus, and i cant find that. And it buggers me when climb pro takes over before a crossroad and i did not see which way i gotta go.
Great tip, thank you! Quick question: can you use the ClimbPro feature on the Edge 1040 while doing e.g. a triathlon? My ideal setup would be to just set the Edge 1040 into Extended Display mode, have the .gpx file loaded and guiding me on the bike course, and still see the ClimbPro data. Is this possible?
@shane Miller the problem is that there is 2 behavior on climb pro. One on free ride ( imo the best one as you can still see the map) and another behavior when you are following a course. That one is very very annoying as it maks the map by a pop-up and replace with what we see on the right at 3:30. It’s happened multiple times that on a descendant just before another climb with 2 or 3 different roads the climb pro pops up …and you don’t see the map anymore!,, 2 solutions or stop and change screen on the edge to come back on the map ….or to gess the road….. very annoying as I said. Why Garmin do not introduce a switch On/off function for this?
Hello GPLama,maybe different topic… Is there any way how to see waterpoints on the map allways? I know there is a function navigate to waterpoint,but on themap I can see pointless carpark poi.What I found on the internet looks quite difficult to me toget ist displayed as waterpoint poi.
Thank you very much Tom
I like the look of this data screen, but I can't figure out how to change mine on 1040 to show a map and that style elevation profile... Only the bottom 2 fields are editable, the top 2 are seemingly stuck on the large "are we there yet" field, and a large elevation profile that shows no other data.
Same here on my Edge 1040 Solar. At the top, he has the navigation map, but I don't. I have a huge Distance To Go and Ascension Remaining which takes up far too much valuable space. How do you get these replace by the navigation map ?
OK, so people in other comments are saying the map will only appear in free ride, not if you are following a course. Weird logic.
@@ugomarsolais Agreed. Bizarre..
Awesome & Thanks :)
Hi shane, on my edge 840 I do have climb pro anabled. In the setting the ‘show screen’ and ‘pop-up’ option are enabled as well. The problem I get, is when navigating, the climb pro screen Pops up but then the map and navigation is gone…. On your screen the climb pro is beneath the map, but that option i cannot find…. Did I do something wrong? Did I miss something? Thx considerabel :) ! Love your content!
very nice thanks for sharing, just installed.
however I fail to configure my ClimbPro screen on my Edge 840 the way you have it set up at 0:12 on your 840 solar. The only option I have is the layout you have at 3:47. how can I change that?
is there a way to get rid of the MAP at the top. I find it completely useless as I'm going slow enough up a hill to see where I'm going. All I want is the colour gradient chart and a few other bits of info - speed HR Cadence etc on screen and large enough for my 65 year old eyes to see. I have the Edge 840. Any thoughts?
Just tried this on my 530. You get 4 data fields on each side.
Why can't there be a elevation profile and map together like in Wahoo? I miss that a lot on race routes so that I can prep for climbs.
Struggling to set this up on the Edge Explore 2018 version, by struggle I mean adding the map
I like the ud
Hello, is it possible to place the information in the middle of the larger screen in ClimbPro?
Thank you
Love the jersey - are you selling Llama merch?
Cheers! Not at this time. Maybe one day.
@@gplama revenue stream untapped there...
Thanks Shane. How did you get the map on the climb pro screen please?
Looks like that might only be a 1040 thing.
On my 1040 the map is also missing on the climb pro screen. Anyone know how to activate this?
@@gplama on the 840 the map is shown in freeride, but not when using a route.
@@ddxleoncuprar @gplama seems to be using a route with ClimbPro and map both visible (see 5:50 for example)
@@gplama On my 1040, I don't have the map on climb pro page. beta firmware.
How do I keep the map during climb pro? It dissapears during a climb and just shows elevation and those 2 data fields. My unit is Explore 2.
You’ll need a 1040 with more screen realestate.
@@gplama my map disappear even on the 1040 when I have selected and riding a course. Is there a workaround? Sometimes it happens that our group are leaving the course in Front of a Climb without knowing because we loose Information about the track when climb pro pops up
Same issues, on climb pro screen, you just have "distance to go" and "ascent demain"
When I installed and configured this on my 840, it actually did put 4 data points in each of the two data boxes. Those were too small to read, and I could not figure out how to reduce the number to two for each data box. Any advice?
Hi, I cannot find "Mapfields" but there is a Mapfields #1 .
What's the difference between Mapfields #1 , Mapfields #2, Mapfields #3 ?
Which one should I install on a 1050 ?
Hi sir what can you say about magene qed power meter? Is it lighter too? Thanks
Hi! After my vacation I had a ride today and map did not display in climbpro. Is they any recent update finally fixed that issue?
I have a question, on the edge 840 will it only show 2 fields or 4 as you show in image 4:12?
That wind info, is that live form what it measures, or does it get the info from the internet thru a connected phone's internet?
It comes from Internet weather services.
Somehow my 1050 let me put 4 total data fields on climb pro, but only when I do it on my edge not via the app. Haven’t tested it but it seems to be working based on the preview.
I can get the screen with the map, climbpro and the data fields while riding without following a course. If I ride on a course, I cannot get the combined screen, I only get the map and the data fields. Am I missing a setup somewhere? I could not find this information watching the video many times.
On my E1050 the gradient field displays significantly delayed/wrong gradients then the Edge orig field atm, maybe needs dev tweaking?
Hey, how can I setup that I will see map during climbing in climb pro? I have 540 and Im not able to set it up.. Thanks!
Strange I have the latest firmware on a 1040. But I can’t change data fields in climbpro 😢
Ok, I got the four small fields set up. But, how do you get the route map to show above the climb profile? I can't seem to change the Climb Pro current upper display of Dist to Go, Asc. Remain and Grade Remain.
Apparently it only does this for ClimbPro in free riding on the 1040. Something thy should add to ClimbPro when following a route too, imo.
@@gplama Ah, I have a 840 Solar. Sometimes I miss a route turn because Climb Pro jumped up. I thought you might have had another app running to get the map display above the climb profile. Thank you for all the great videos.
Using 1040, how do I change the specific data fields? Mine currently has speed, cadence, Ascent and HR. Shane’s had 3s Pwr. Thanks for sharing.
2:07 Garmin Connect IQ App, go to the settings for the data field and tap each field ex. Upper right/left, etc. It gives you the option to replace each one
@@gordonconrod7628 Thank you - most helpful.
What camera are you using for your ride in this video
Insta360 X4
Hi is there an app that will connect your Garmin Explore 2 to you Di2 system? Bike is set up to connect to my previous head unit 520 edge
One for Garmin Support. I don't believe the Edge Explore 2 can connect to Di2 ANT like other Edge units.
I’m annoyed that ClimbPro doesn’t work in free ride on Edge 830… Why do I need a new device for that? 🤦♂️
Hi Shane, do you know of anyway (on an Edge Explore2) to increase the size of blue location arrow and the history line on the map? I just find them too small, regards from Italy (escaping Ballarat’s winter) !
There’s a file hack to change the position triangle. Not sure about the line thickness though. I’ll dig more into this when I get the chance.
@@gplama did you ever publish anything on manipulating the triangle?
@@m5paeplow Not yet. It’s over on the Garmin forums if you want to dig into the details.
It is great that we have those custom field apps, but is it possible to disable this stupid "Climb starting" countdown? It drives me nuts that I can't see my power anymore unless I tap on this. And then this useless "Climb!" green box that appears for too long as well. What are those for, for people that want to measure their climb performance progression on local climbs or what?
how do i get rid of the map and replace it with the dist to go and asc remaining fileds?
So does free ride for climb pro work on a 1030 edge +? My standard climb pro comes up if I scroll through the pages, it doesn’t come up automatically but map fields doesn’t come up at all?
No. It’s an x40 series only feature for free riding.
@@gplama awesome, thanks Shane for replying. Keep up the great videos 👌
Does anyone know how to get edge mapfields to work with hr zones? Theres a toggle for it, but no option to select it to be shown on screen.
Edge 830 here, rey to download mapfields it says Queued
which 2 fields (of the 4 you can configure) are shown on the smaller devices?
The two left fields.
@@gplama thank you!
not sure, what I do wrong, but my ClimbPro screen looks always like at minute 3:14 in video. I never so any map on top.
same here, how to add it?
brill
And what happened with iGSPORT 800, review ???
Still in progress. As I've replied to someone else here already tonight - The iGS800 is simply not ready for release. There's so many things wrong with it they needed to spend another six months fixing things before launching. There's some unfixable hardware issues too. The review will be out sometime soon. It's not great.
Why do we need a map on screen at all. Just want the climb part and the bottom part.
I personally think that’s really useful. Quite often on a climb there is a turn and when on an effort simple mind often forgets the turn 😊
As someone who races, it really helps to know exactly what turn’s coming up so I can position myself properly and stay safe too 👍🏻
Or... why i cant just choose what I want on that screen?
Because I have a nice big 1040 screen to fill up
Often there is a fork in the road and you can easily go stright instead of turning or vice versa and deviate from the climb/route/segment
Can you get wind info on wahoo roam v2?
Where does it get the information about the wind? It is accurate?
See the link in the video description for all the details about WindField.
don't you find the wind direction points all over the place?
it really shouldn't. the data is coming from the stations near your location so as long as they are accurate, the arrow shouldn't jump around
@@windfieldapp i think its the bike computer not having a consistent view of North rather than the 3rd party data )mpt your datafield, I use a different one)