ACURA MDX CHECK ENGINE LIGHT ON, VSA LIGHT ON, ABS LIGHT ON! Diagnosis & Repair Part 2
Вставка
- Опубліковано 23 сер 2024
- in this video I will share with you! how to diagnose and fix one of the causes of an ABS Light, VSA Light and Check Engine Light that Stays On While the Engine is Running, This is Part 2 of a 2 part video!
#abs #checkengine #02sensor
Been busy K working on a Hydro locked Tahoe. Engine was replaced last year. A lot of problems with this vehicle. Thank you again for a great diagnostic and repair video.
Richard 1 My Pleasure!! I wondered where you've been my friend! how's the Chevy project going, are you replacing the entire engine?
Hey Buddy, You did very good job of explaining. You are professionals of your field. Thanks for the effort of diagnostic video and please keeping the good work.
todd saechao Thank you! I appreciate it!
We are still following, great work and video K Diagnostic thank you
Suleman Habib My Pleasure!! I appreciate you bro!
I watched both videos, you did a great job with the diagnosis/repairs as well as the video edit & content. You video'd the relevant information & didn't involve hours worth of content that doesn't help the viewer.
Going to subscribe and check out your other videos, great work & great channel!
kevinnagle Thank you! and welcome to our youtube community!
The ST🌟R, amazing video!
DinhaS Thank you!!
Thanks for your efforts 👌
Olugbenga Akinlade My Pleasure!!
Thanks four the education bro
Amadou Diallo My Pleasure!!
good works again thanks
Paul Foldes My Pleasure!!
Very excellence machanic
@tettunoo5005 Thank you!
We were keep waiting for this,thx.One question,how do the wide band O2 sensors differ from others!tell us little abt it.Thx
Highest Forward Gear My Pleasure!! Wide band 02 Sensors have a wider range of mesuring oxygen content in the exhaust stream, which makes them more accurate than the narow band 02 sensors!!
Ooh!got it.Thax
Nice video you're a beast 💣💥👍
Fast Thank you!
Nice work!! That's some top notch diagnosis. You can have the tools, but you need to know how to use them as you demonstrated.
I noticed that this car temp doesn't go up all the way to the half way point when at operating temp. Mine does the the same and I replaced the coolant and thermostat. Do you think it's the coolant sensor?
Thanks
FortunateDaD Thanks! yeah your sensor might be under reporting
@@KITS_Auto_and_Truck_Repair thanks! Prior the car wasn't heating very well and noticed the temp Guage wasn't quite in the middle. Now since replacing the thermostat, i get good heat and alot faster but the needle still doesn't reach the middle.
Keep up the good work 👍
@@fortunatedad7695 My Pleasure! Thanks
I need my acura mdx fixed. Where are you located, my friend? Great job
@mtothezine Thank you! our shop is located in Dickerson MD, You can email me at kitsautoandtruckrepair@gmail.com to set up an appointment
Good job sharing
Alexander Stefanxandra Swedish Thank you!
I could see the red and blue traces switching positions on the scope, I could see a voltage swing between 3 and 4 volts, it would have been nice to see how often this swing was happening on a more zoomed-in voltage scale with lots more time on the screen such as a 5 volt scale only watching these 2 signals with maybe a full minute on the screen. I know wide bands have little activity of any great detail, thank again for the nice diagnostic. I also would have like to know if the actual heater was working even though the scope showed good PCM control, was it actually getting hot since there was a code for the heater?
Duane Donaldson My Pleasure!! The Heater was open, the voltages on the Scope screen confirmed wiring integrity and ECM command!!
where you working my mdx have vsa end trailer stavility tracction control ligh on
@jaimenavarro6388 Sorry! I didn't understand your question!
Can you do some video on 2006 highlander hybrid battery system check light is on.
todd saechao yes I can! I will do, when one with a battery issue comes to our shop!
Where you live I have an mdx just like you fix maybe take my
Alejandro Nieblas Our shop is located in Dickerson MD, you can email me at Deo@calleva.org for shop info!
Hi, so when you connect a scan tool, to diagnose the ABS system. It's normal for the ABS/VSA light to come on the dashboard ? I'm having a ABS/VSA come on when connecting a scam tool. Thanks in advance.
@luisperez-mex-los Yes! that's normal!
You hardly use your autel maxi sys ultra. Seen you used it once. Any particular reason(s) for this
Mayowa Odus I like the way data pids are Written on the Snapon scanner, it's a bit user friendly, and I tend to use my Autel scanner when I work on European vehicles!!
How can fix my Acura 2007 MDX I have same issues
@timothyfaniu check your grounds!
I wish I can bring it to you
Can you help me with my 2017 Honda Odyssey
TechMan21 how can I help?
Why does the abs light stay on when the scanner is connected?
Bart Young I don't know exactly why the ABS light stays on when the scan tool is connected, But I believe it stays on to confirm that the ABS module is communicating with the scanner!!
How to ft come lean when press brake paddle
Visal Prabhashana Ariyarathna by pumping the brake pedal you create a vacuum leak in the brake booster which affects the air fuel ratio! and you can see it on the 02 sensor signal!
Thank you very much master