I have a NoricTrack 2450 (bought it in August 2021). It was working perfectly up until a few weeks ago when it started making some weird sound, especially when inclining. Turns out it was just a change in climate and the back feet were now bouncing (just needed to put some rubber matting down). Only thing is, after the technician serviced it the 'seconds' on the elapsed time were no longer in synchronisation with the 'seconds' on the lap time, with the former falling back lap by lap (beforehand the 'seconds' on each were always in sync). My wife also notifced when using iFIT after the service that it was prompting her to 'follow trainer' when it had never done this before. I noticed when the technician had the cover open he turned a screw and saying "that seems tight". Not sure why he needed to do this as we had already establised the original noise was happening because of the back feet bouncing. So I read that the calibration can be tuned by turning a screw under the cover. I'm just hoping the technician didn't turn this particular screw which could have caused this issue, but it does seem very coincidental the issue occurred right after he serviced the treadmill. I'm hoping I can fix this because it's really ticking me off.
Hmm this is hard for me to answer never heard of climate affecting treadmill this way .So I can't answer that . On the speed issue it is possible the speed IR was turned it not a screw per say it is either a small orange or white phillips head adj port . but I thought on units 2020 and newer this port was two heavily glued to adj . check it and see if yours is . But the I fit error you would have to contact I con on that that's there private system Sorry I don't know anything on that ( yet) ua-cam.com/video/4MeR4NPKd7c/v-deo.html the link I sent is the controller I am familiar with Nordic . hope this helps Dave
@@FitnessTechnologyServices When I say 'climate' I live in a part of the world where it goes from one extreme to the next, so I think 'just fractionally' the floor might have contracted or, the base of the machine slightly contracted. But that part of it is OK, because we just put down rubber matting which fixed the problem.
@@FitnessTechnologyServices Thanks for the tip, I'll look into it. Yes, I did read something about a coloured screw or something. I remember the side of the machine the technician did 'his' procedure so I'll be sure to check out that side of the machine (especially). As I mentioned, I just don't why he even needed to do this as we had already established what was causing the noise. I guess the principle applies, if it isn't broke don't fix it.
hi, great video just finished the calibration. have same threadmill, just have a question it seems incline don't go all the way down any solution to that ?
Then it is the controller once the buttons work on the console. And it runs at full speed or at least super fast then it is the controller. I have a video on this called motor controller failure
Hey, do you know what type of screw goes into the front roller of this treadmill? I’m changing the walking belt and lost the screw and don’t remember what it looks like 😢
I have changed the lower control board, red and green lights stay lit. Incline motor works but the belt does not move and can’t calibrate speed. Any suggestion
Hmm the next step is to test the motor off of a separate dc power supply. Also is there a light on your controller to say the start signal from the console is working
Hi, once again. I have issue with same threadmill, now when i push speed number 3 or 2 it goes really fast it wasen't doing that now it just goes fo fast when pusshing a low speeed, i try key out press stop and up speed and i don't get the display on your video ?
Hmm that’s hard to say different issues normally when it goes fast at no matter what speed the issue is in the controller. But when it won’t go into calibration this can only be in the console. It should at least go into calibration even with bad controller. Hard to say
Well both you can still get key . And you could try any plastic tool that will fit .I have used a plastic Spackle knife in a pinch. What you are doing when you insert your key is hitting a micro switch in side
I have a Nordictrack viewpoint 3200 that now just turns and lights up like normal but just beeps and doesn't start moving at all and the button functions are not working it just beeps when I push the speed button and it also beeps like every minute when it just sits there. Do you have any idea what's going on? Any info would be greatly appreciated. It use to work great, then once and a while, then once and a while with a beep every minute or so. now it won't work, it just does as I described in the beginning.
Well that is a bad console. And unfortunately Nordic Track does not have parts any more you are probably going to have to search EBay to see if there are any out there
Hi, have a few other questions. Okay now treadmill seems to work normal, I think the issue is been cause when leaving threadmill on lid up its when it gets faulty, just have a question is ig possible that when running at a 5 speed can go super fast or max speed as it was doing yesterday ? i am a bit concert about that if im running since speeds raises quickly
@@jrsanders1983 well you might have a issue with the console. All non touch screens should calibrate the same way. What issue are you having do the buttons beep when they are pressed
@@FitnessTechnologyServices Whether I put the key in by pushing the buttons or just put the key in without pushing those 2 buttons I get the same result. All zeros and ready to start the machine. There is a settings button and I got into a demo mode somehow after I held stop and plus after I clicked the Settings button.
Hi thanks for the video, is this same way to calibrate nordick track T17.5 3CHP? Just bought one was working before I move it to my place. I move it in two part just separate the upper part off the bottom . Any help is very apprecoated
Hmm I am sorry not sure 90 % of Nordic Track calibration is done this way.If not there is a small gear ⚙️ Icon that will put it in calibration.But I would go over all your connections also .
Hi! Can you help me decide which (used) NordicTrack model would be best? Shopping around between a C2270, an Elite 3750, and a T7.0 on OfferUp. Thoughts?
Well I am not good at judging treadmills I would go by the original manufacturer warranty the better they warranty it the better parts they put in. And in general I wouldn’t by a used one with a touch screen. Cost to much to replace
Hmm there are a lot of I guess the first one would be a bad motor controller. You will need to check the ac power to the controller I have a video on troubleshooting sole motor controller on fitness technology services
When I'm calibrating the incline on my C2000, it makes a humming sound, has the flashing lights for a moment, and then goes to a 0 without moving. What can I do differently?
This is hard to say two possibilities either the controller has failed or you might try reversing the red and black wires on the incline motor it’s self. Red is normally up and black is down sometimes they reverse?? Be careful this is straight 110 voltage ac . Make sure you unplug unit just to be safe
@@FitnessTechnologyServices I've unplugged the white cable from the motor. The wiring all matches the schematic. There was power going to the motor, but it's giving off a burning plastic smell. I think something has melted, and it's possible it's stuck.
@@ccross04 Well the best way to answer that is to remove the incline and see if the threaded end will move by hand? Or is it locked up . Also unplugging the white wire will disable the incline. But I was trying to see if the red and black wires had reversed signal ? Believe it or not but sometimes it happens I am going to do a video on this very issue this weekend subscribe and it will update you when I post it
@@giovannigalante450 It is hard on older parts. You would need to look at eBay. You would have to look for a power incline board . But you could try unhooking the neutral/ white wire on incline motor and use unit running only. Look at my video on understanding Nordic Track components. Or look on my channel Fitness technology services hope this can be helpful
Well if it is running good then nothing. If it is causing issues then there is a small Phillip head adjustment normally orange? To adjust speed. But you have to be careful and don’t touch any metal
Turn the orange screw on the controller board counterclockwise slightly to slow it down a bit. Just finished doing mine today along with replacing the motor belt, now at 85% mine is right on 10.0, good luck! (NordicTrack A2250)
You could post a pic and I could tell. But in general all are the same.Until you get into the touch screen style. There are a couple of years Nordic Track were you would have to get into maintenance. And you would press a small gear ⚙️ icon to calibrate
Yeah that definitely didn't work on my treadmill. I held the stop and speed button up then put the key in and let the buttons go and nothing happens..I just see 0.0
I see you said decline is this a newer unit with touchscreen Or I fit if so they don’t calibrate the same way hopefully one of my subscribers will see this and help out
My treadmill was stuck on 4 incline and I could stop start or use the speed up button. This worked flawlessly! Thank you!!
@@t.mooreyewknow799 Awesome and my pleasure!
That worked on the 1000xi. Stuck in line fixed. Thanks.
I have a NoricTrack 2450 (bought it in August 2021). It was working perfectly up until a few weeks ago when it started making some weird sound, especially when inclining. Turns out it was just a change in climate and the back feet were now bouncing (just needed to put some rubber matting down). Only thing is, after the technician serviced it the 'seconds' on the elapsed time were no longer in synchronisation with the 'seconds' on the lap time, with the former falling back lap by lap (beforehand the 'seconds' on each were always in sync). My wife also notifced when using iFIT after the service that it was prompting her to 'follow trainer' when it had never done this before.
I noticed when the technician had the cover open he turned a screw and saying "that seems tight". Not sure why he needed to do this as we had already establised the original noise was happening because of the back feet bouncing.
So I read that the calibration can be tuned by turning a screw under the cover. I'm just hoping the technician didn't turn this particular screw which could have caused this issue, but it does seem very coincidental the issue occurred right after he serviced the treadmill. I'm hoping I can fix this because it's really ticking me off.
Hmm this is hard for me to answer never heard of climate affecting treadmill this way .So I can't answer that . On the speed issue it is possible the speed IR was turned it not a screw per say it is either a small orange or white phillips head adj port . but I thought on units 2020 and newer this port was two heavily glued to adj . check it and see if yours is . But the I fit error you would have to contact I con on that that's there private system Sorry I don't know anything on that ( yet) ua-cam.com/video/4MeR4NPKd7c/v-deo.html the link I sent is the controller I am familiar with Nordic . hope this helps Dave
@@FitnessTechnologyServices When I say 'climate' I live in a part of the world where it goes from one extreme to the next, so I think 'just fractionally' the floor might have contracted or, the base of the machine slightly contracted. But that part of it is OK, because we just put down rubber matting which fixed the problem.
@@FitnessTechnologyServices Thanks for the tip, I'll look into it. Yes, I did read something about a coloured screw or something. I remember the side of the machine the technician did 'his' procedure so I'll be sure to check out that side of the machine (especially). As I mentioned, I just don't why he even needed to do this as we had already established what was causing the noise. I guess the principle applies, if it isn't broke don't fix it.
Great instructions, thanks!
Well thank you!
Can you made a video how to recalibrate after replace motor on Nordic track treadmill x7i. Thanks 🙏
Sorry I don’t have access to the x7i only the one showing
hi, great video just finished the calibration. have same threadmill, just have a question it seems incline don't go all the way down any solution to that ?
Well thank you! But not really if the system is satisfied and passed calibration it won’t let you alter it
Hi
I have a issue. I have same treadmill. When I tried to calibrate my Max Speed does not match with my Max Incline. What to do?
Thank you
If it passes calibration there’s nothing you can do . A lot of treadmills don’t have the same height and speed settings and thank you
i was able to go to calibration did the steps but its doing the same isssue
Then it is the controller once the buttons work on the console. And it runs at full speed or at least super fast then it is the controller. I have a video on this called motor controller failure
@@FitnessTechnologyServices okay thank you so much will look for video now
Hey, do you know what type of screw goes into the front roller of this treadmill? I’m changing the walking belt and lost the screw and don’t remember what it looks like 😢
I believe it is the same as the rear adjustable bolt. You could check it to make sure! But I think for Nordic Track it’s 1/4 20 ?
I have changed the lower control board, red and green lights stay lit. Incline motor works but the belt does not move and can’t calibrate speed. Any suggestion
Hmm the next step is to test the motor off of a separate dc power supply. Also is there a light on your controller to say the start signal from the console is working
Hey, what if the motor starts and stops immediately
Well there are lots of possibilities on that! Does it run with no one on it?
I have the same problem, please advise how to check the problem.
Hi, once again. I have issue with same threadmill, now when i push speed number 3 or 2 it goes really fast it wasen't doing that now it just goes fo fast when pusshing a low speeed, i try key out press stop and up speed and i don't get the display on your video ?
Hmm that’s hard to say different issues normally when it goes fast at no matter what speed the issue is in the controller. But when it won’t go into calibration this can only be in the console. It should at least go into calibration even with bad controller. Hard to say
@@FitnessTechnologyServices nothing i can do? reset maybe as i use everyday to walk after a ischemic injury?
will try to go into calibration again
i notice that the speed numbers when display turns on the speed numbers move around
Hey wanted to know if I can still power on the treadmill without my key? I lost the key and was wondering if there’s a replacement key for it
Well both you can still get key . And you could try any plastic tool that will fit .I have used a plastic Spackle knife in a pinch. What you are doing when you insert your key is hitting a micro switch in side
I have a Nordictrack viewpoint 3200 that now just turns and lights up like normal but just beeps and doesn't start moving at all and the button functions are not working it just beeps when I push the speed button and it also beeps like every minute when it just sits there. Do you have any idea what's going on? Any info would be greatly appreciated. It use to work great, then once and a while, then once and a while with a beep every minute or so. now it won't work, it just does as I described in the beginning.
Well that is a bad console. And unfortunately Nordic Track does not have parts any more you are probably going to have to search EBay to see if there are any out there
Hi, have a few other questions. Okay now treadmill seems to work normal, I think the issue is been cause when leaving threadmill on lid up its when it gets faulty, just have a question is ig possible that when running at a 5 speed can go super fast or max speed as it was doing yesterday ? i am a bit concert about that if im running since speeds raises quickly
Yes for sure it can speed up any time be very careful
Tells you not to stand on the walking belt AFTER the function starts with me on it …
In general it is better for the treadmill if you let it start with out any one on it . But no one does that
But never be on it when calibration is done
Can you show how to calibrate nordictrack commercial
Sorry I don’t have a touch screen to work with
How do I do this on my c970 pro? I tried but I didn't get any menu. I was able to calibrate the incline via ifit
Sorry I am not familiar with the c970 if it is a touch screen this style calibration won’t help
@@FitnessTechnologyServices its not a touch screen, but i couldnt find any documentation online
@@jrsanders1983 well you might have a issue with the console. All non touch screens should calibrate the same way. What issue are you having do the buttons beep when they are pressed
@@FitnessTechnologyServices Whether I put the key in by pushing the buttons or just put the key in without pushing those 2 buttons I get the same result. All zeros and ready to start the machine. There is a settings button and I got into a demo mode somehow after I held stop and plus after I clicked the Settings button.
@@jrsanders1983 yes that sounds like a bad console
Thanks for the intro but we really don’t need the intro - short and sweet ….
Hmm not sure what to say I need the into to promote my channel
Hi thanks for the video, is this same way to calibrate nordick track T17.5 3CHP? Just bought one was working before I move it to my place. I move it in two part just separate the upper part off the bottom . Any help is very apprecoated
Hmm I am sorry not sure 90 % of Nordic Track calibration is done this way.If not there is a small gear ⚙️ Icon that will put it in calibration.But I would go over all your connections also .
How much did yours cost
Hmm the treadmill was given to me for video . I think they ran 900.00 but that was 15 years ago .The console is used to run around 300.00 or less
Hi! Can you help me decide which (used) NordicTrack model would be best? Shopping around between a C2270, an Elite 3750, and a T7.0 on OfferUp. Thoughts?
Well I am not good at judging treadmills I would go by the original manufacturer warranty the better they warranty it the better parts they put in. And in general I wouldn’t by a used one with a touch screen. Cost to much to replace
@@FitnessTechnologyServices much appreciated!
I have a question about a sole f63. I turn it on and the light on the power button is on but nothing happens. What does it mean?
Hmm there are a lot of I guess the first one would be a bad motor controller. You will need to check the ac power to the controller I have a video on troubleshooting sole motor controller on fitness technology services
@@FitnessTechnologyServices ok thanks. I will watch the video.
When I'm calibrating the incline on my C2000, it makes a humming sound, has the flashing lights for a moment, and then goes to a 0 without moving. What can I do differently?
This is hard to say two possibilities either the controller has failed or you might try reversing the red and black wires on the incline motor it’s self. Red is normally up and black is down sometimes they reverse?? Be careful this is straight 110 voltage ac . Make sure you unplug unit just to be safe
@@FitnessTechnologyServices I've unplugged the white cable from the motor. The wiring all matches the schematic. There was power going to the motor, but it's giving off a burning plastic smell. I think something has melted, and it's possible it's stuck.
@@ccross04 Well the best way to answer that is to remove the incline and see if the threaded end will move by hand? Or is it locked up . Also unplugging the white wire will disable the incline. But I was trying to see if the red and black wires had reversed signal ? Believe it or not but sometimes it happens I am going to do a video on this very issue this weekend subscribe and it will update you when I post it
@@FitnessTechnologyServices I will try this. Thank you for your suggestions. Looking forward to the video
I the Apex 4500 same to calibrate? I tried and It keeps going to FF after shut off
thank you for the video
Yep same calibration! FF sadly stands for fail fail
Console bad or if belt doesn’t move at all maybe controller!
@@FitnessTechnologyServices how can I fix it once I calibrate and unplug it needs to be calibrated again?
@@giovannigalante450 It is hard on older parts. You would need to look at eBay. You would have to look for a power incline board . But you could try unhooking the neutral/ white wire on incline motor and use unit running only. Look at my video on understanding Nordic Track components. Or look on my channel Fitness technology services hope this can be helpful
Also when doing calibration speed when above 10 what do i do ?
Well if it is running good then nothing. If it is causing issues then there is a small Phillip head adjustment normally orange? To adjust speed. But you have to be careful and don’t touch any metal
Turn the orange screw on the controller board counterclockwise slightly to slow it down a bit. Just finished doing mine today along with replacing the motor belt, now at 85% mine is right on 10.0, good luck! (NordicTrack A2250)
Does anyone know if this will work for the T 6.5S?
You could post a pic and I could tell. But in general all are the same.Until you get into the touch screen style. There are a couple of years Nordic Track were you would have to get into maintenance. And you would press a small gear ⚙️ icon to calibrate
Yeah that definitely didn't work on my treadmill. I held the stop and speed button up then put the key in and let the buttons go and nothing happens..I just see 0.0
Hmm that’s a bad console does it work normally and just failed calibration
@@FitnessTechnologyServices it works normally and displays everything correctly.. its just won't incine or decline
I see you said decline is this a newer unit with touchscreen Or I fit if so they don’t calibrate the same way hopefully one of my subscribers will see this and help out
Mine won’t even turn on
Do you have power light on your controller .If yes check your harness for pinching.After that, maybe in console