How to remove ignition switch, bezel & key cylinder- 1966 Ford Mustang
Вставка
- Опубліковано 24 бер 2022
- Things I used in this video. As an Amazon Associate I earn from qualifying purchases
Ignition switch amzn.to/48dGbew
Ignition Switch Bezel amzn.to/3IE4C8g
Ignition Switch Pigtail amzn.to/3Np5pxp
GoPro Camera & accessories amzn.to/2NwysVu
Lighting set up amzn.to/3ph54R2
Check out Alf's Mustang Parts on Amazon www.amazon.com/s?me=A2LHNSZDF...
Subscribe to the channel and click on the notification bell. / @alfsmustanggarage
We want your thoughts and comments below. What kind of project are you working on? What Mustang are you daily driving? I respond to all respectful comments.
Alf's Mustang Garage is not responsible for any mechanical or technical error that you may encounter when working on your own car. You are responsible for your own quality control and your own proper repairs.
Today at Alf's Mustang Garage, we demonstrate how to remove your ignition key cylinder, your ignition switch bezel, and your ignition switch from a 1966 Ford Mustang. - Авто та транспорт
Great tip!
Thank you!
Dang that was fast and easy! Very nice! Piece of cake! 😁
Piece of cake!!!!
That is alot cleaner and easier then the hole saw new hole in dash and new key switch from tractor supply and some "race car" inspired toggle switchs trick.
Yes sir 🤣🤣🤣
Installation is the reverse of removal - I often just take that line as, 'you know what to do, now do it.' But in my case, I actually had to use the paperclip to get the cylinder to seat back in where it should (even though it was lined up properly, it would not pop back in). I struggled for 30m before I figured that out... ha.
Good video but what if I don't have the key?
I think I need a new ignition switch with a new key.
I forgot to mention I have a 67 mustang
Last time I ran into this situation I ended up buying a basic lock pick set from Amazon. I ended up picking the lock after maybe 10 minutes and removed the ignition cylinder. From there you can install a replacement that comes with a set of keys.
Thx! Helps a lot!!
You're very welcome
I have a 1966 Mustang convertible but cannot locate the key to the ignition. Should I have a key made, replace the cylinder,and since I don’t have the key how do I remove the cylinder?
Well I think a locksmith could probably make a key for you. However if you wanted to change the cylinder, you would have to pick the lock to get it to turn. I've had to do that before. I bought a cheap lock pick set off Amazon.
Good Morning! I might have to replace the Ign switch on my 67 as sometimes it fails to shut off. Don't recall a hole in lock when I took it off last fall. Most likely, will replace the switch and lock/tumbler too. Take care my Brother. Blessings from Motown/Dearborn
Yup! Seen that a couple times. Good luck my friend!
I actually ruined the sheet metal around the hole while prying out the bezel 10 years ago...Back then I didn't know that the ignition switch was spring loaded...I just gotten the Mustang and was a total newbie and not much information out there. A few years ago I had to do the repair and close up the hole and weld in a circular patch and meticulously make a new hole and the 2 smaller/larger side notches.
Oh wow that sound like an experience. Ya we have it pretty good now with so much access to information. Good to hear you have the skills to fix it though.
👍
👍
Alf hey i was wondering which wire would you splice into to install a kill switch ??
You would want to splice into the wire that activates the starter solenoid. This wire was a red with blue tracer for many years and comes off the ignition switch, goes to neutral safety switch if equipped with an auto trans, and then to the S terminal of the starter solenoid.
@@AlfsMustangGarage Thank You Much ! I'm gonna install a kill switch on my 66.. 😁
Need to know what wires come off the ignition cylinder from dash toward block I have all stock wires
What year?
@@AlfsMustangGarage 66 inline 6 200
@@AlfsMustangGarage need to know colors of the original wiring from the ignition switch to the engine bay
I would invest in one of these. I highly recommend it.
classiccarwiring.com/products/1966-ford-mustang-color-wiring-diagram
How can I get a hold of you to buy a complete ignition for a 65 Ford falcon?
You can go to our website
Great seeing this sort of information. Is this the same for a '65? My key bezel is upside down would love to get it in correctly.
Yes sir, should be the same!
Shake and bake
You have to shake it before you bake it.