Yeswelder MIG-205DS-B Multi Process Welder Review and Test!
Вставка
- Опубліковано 7 лют 2025
- Today we take you through the process from unboxing all the way to enjoying the sleek performance of the Yeswelder MIG-205DS-B multi process welder. This welder comes MIG, stick and aluminum welding ready right out of the box! Lift Tig setup and spool guns can be purchased separately using my referral link below! Enjoy!!
!!! For $50 off your next Move Bumpers order or 10% off at Yeswelder use my referral links below and my ambassador coupon code "GMP" at checkout!!!
Links:
YESWELDER - yeswelder.com/...
MOVE BUMPERS - move-bumpers.m... !!! For $50 off your next @Movebumpers order, 5% off and free shipping @diodedynamics , 10% off @YesWelder , 15% off @AUXITOLED and 6% off @fitcamx Dash Cameras use my referral links below and my ambassador coupon codes at checkout!!!
DIODE DYNAMICS - Coupon Code: GMP
Link: www.diodedynam...
AUXITO - Coupon Code: GMP
Link: www.auxito.com...
YESWELDER - Coupon Code: GMP
Link: yeswelder.com/...
MOVE BUMPERS - Coupon Code: GMP
Link: move-bumpers.m...
Fitcamx - Coupon Code: Fitcamx821
Link: fitcamx.com/?s...
![Lp. Сердце Вселенной #60 РОЖДЕНИЕ ЛОЛОЛОШКИ [Финал] • Майнкрафт](http://i.ytimg.com/vi/YoR0pAV9FVQ/mqdefault.jpg)
Thanks, friend. I decided to retire my ancient Lincoln welder and upgrade - but the Yeswelder manual leaves a lot to be desired. Your explanation is clear and concise. I'm up and running.
I just bought one of these and used it for MIG (.035 w/ gas) and stick (6013 1/8" inch rod) for the first time today. I couldn't be more satisfied. I have never stick welded with DC before. What a difference! I was hooked on welding before, but now I am really into it! I have a TIG stinger and consumables coming this week for it. I have never TIG welded before but I am excited to try it. Just a very good welder that meets a lot of needs at a great price. All the components appear to be very good quality. I was running it on 240V. I haven't tried it on 120V yet. As some have said, the access door is not quite wide enough to allow easy access for roller changes, but it is still pretty easy to do, so that is a very minor complaint.
Glad you enjoyed it as much as i do! i agree completely with your comments. the access door is a bit small but if you run a 10lb spool wire changes are not often. Small tip for if you try 110v is to dial the amperage down and work up. It doesn't recognize when you are on 110 vs 220. If you have it up over 15 amps you most likely are going to pop the breaker.
Just ordered one today! Can’t wait! Also located in the 802. Happy welding!
Hell yeah man! enjoy!
DUDE! I only watch UA-cam (no cable for me) AND THIS IS THE BEST REVIEW IN HISTORY. SUBBED! Keep ‘em coming please!
I appreciate it! will do!
Nice video brother. I just picked one of these up and that was good information. The rig used many years ago was much different than this little thing. I’m surprised how well it works. Thanks again.
Very nice. I purchased one several weeks ago. It’s now July 2, 2024. I had to refer to your video for clarification on some settings as I found their manual directions less than satisfactory. One thing I noticed is you cannot make the unit on the face panel change the diameter of the wire you’ll be using, and I don’t know how to change it from what was said at the factory, which is the same as you have on yours, doing this video post.
Great video and demonstration
make a video on all the different setting and how to set them, and the material thickness etc
Great video, thanks for the run down. When you get it hooked up to gas do a video on that side of it. 👍💯
I will definitely do that, thanks for the feedback!
Be a lot more useful to hear the welding rather than music the sound of the welder tells a lot . .
Good with 6010 stick?
Thank you so much for your video. Is the machine still working fine? Is it advisable to buy it? Thank you friend. Greetings from Monterrey, Mexico
Thanks 👍
Hi, thanks for the vid. I'm trying to determine the breaker I need to run this. I have an available 20 amp breaker that I can upgrade to 30 or an available 100 amp breaker that I'll need to add a receptacle at the disconnect box
You could run on the 30 if you don't turn the welder up to its full capacity. I have mine on a 40amp and never tripped it out. I added a 40 amp disconnect which is what i would recommend.
@@GreenMountainProjects thanks so much
Nice overview! Are you still liking this welder? What’s the range in thickness of material it can weld? Also, to confirm, can this be run on both 110V and 220V home circuited, right out of the box? I’m between this one and the Forney multi-process
Yes I am still loving it and would highly recommend over a Forney. this can run on both 110v and 220v right as it comes. This welder gets great penetration as I have welded up to 1/2 very successfully. Feel free to use my referral code "GMP" for a discount on their site!
@@GreenMountainProjects Thanks for the info and the code! Really starting to lean towards this one because it seems to have such little limitations, especially for its price. Two more ?’s:
2- What is the advantage in having the 220V capability over the ones that are 110V only? Is it ability to weld thicker material?
2- Any particular reasons you recommend this over the Forney easy weld 140MP?
Have you had any feed issues? I have the older blue one and have gone through 3 torches in a little over a year because of sticking liners. I got a refund and want to get this because the things I didn't like about the old one are fixed but don't want the same liner failures all the time again
Is there a difference between the 205DS and 205DS-B ?
Pro has color screen and Tweko 2 gun
I have a new yes welder mig 205 ds-b and I'm having issues with the roller knob the black one continues to back off any ideas why
Can find one
back off the spindle its on? did you secure it with the tensioner?
Music was SO much louder than the rest of the video.
Mom didn't come with the chart do you know where I can
What
Download from the Google
is this a 205DS-B?
yes it is
At 7:42 hes gasless fux says NOT to use copper tip but then goes on to weld with it? 🤔 kinda confusing if you're a newb.
Exactly why i said it first. Just didn't have the plastic tip when i filmed those clips.
@@GreenMountainProjectswhere do you get the plastic tips?
@@tylerjones4 Home depot/ Lowes, its the same ones that they have as replacements for the Lincoln electric welders they sell.
@@tylerjones4harbor freight flux nozzles fit
Have You Run This On 110v?
Yes, works great unless you crank it up to 15 amps or higher by accident and it will pop breakers.
@@GreenMountainProjects at what volt and wfs did you run to avoid breaker trip? Also was the breaker 20A?
@@yt78gt it sets in amps and I was just under 15 with a wfs of 5 to 5.3
@@GreenMountainProjects thanks for the response.
So you can’t control the amps separately from wire speed. Lame
That's because it's in synergic mode. In manual you can change them separately.
@@TheSynthnuti have one and you can only change the volts and wire speed in manual mode
it's a bit annoying they use voltage instead of amperage
They upgraded this model. It's now the 205DS Pro. Has full color screen with wire speed in imperial measurements. Did away with the cheesy flip-up display, too. Nice rig.
Where can I get a chart all other welders come with a chart. If you are an expert welder then this welder is for you. If you are new to welding this welder sucks don't purchase it without a chart.
This welder does come with a chart as you can see at time stamp 2:24 in my video. You may want to check your trash as you probably threw it out.
When you're new, don't all welders suck w/o a chart?
Useful video. I wish you would show aluminum welding as the company advertised...
I would have but i'm not very experienced with aluminum. I don't provide content unless I am confident I am giving people the correct info. I have used the spool gun some and it does work pretty well.