How to Replace Drivers Side Mirror 2003-07 Chevy Silverado
Вставка
- Опубліковано 15 лип 2020
- Buy Now!
New Mirror from 1AAuto.com 1aau.to/ia/1AMRE01052
When it comes to driving, it’s important to know what’s behind you and beside you. A broken side view mirror could put you at risk of an accident, or ticket! TRQ side view mirrors are engineered to fit your vehicle. This video shows you how to install the driver’s side mirror but the procedure will be the same on either side of your 1999-2007 Chevy Silverado.
• Check here for more videos on the 1999-2007 Chevy Silverado: • Chevy Silverado 1999-2...
This process should be similar on the following vehicles:
1999 Chevrolet Silverado 1500
2000 Chevrolet Silverado 1500
2001 Chevrolet Silverado 1500
2002 Chevrolet Silverado 1500
2003 Chevrolet Silverado 1500
2004 Chevrolet Silverado 1500
2005 Chevrolet Silverado 1500
2006 Chevrolet Silverado 1500
Tools you will need:
• Pocket Screwdriver
• 7mm Socket 1aau.to/oot/1AXAA00017
• Trim Tool Set 1aau.to/ofe/1AXXX00006
• T20 Socket
• Gloves 1aau.to/obT/1AXSS00048
• Safety Glasses 1aau.to/obm/1AXAA00343
Subscribe: / @trq
Check out our playlist:
Chevy Silverado 1999-2007 1st Gen: • Chevy Silverado 1999-2...
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video. - Авто та транспорт
√ *Watch the Video*
√ *Buy The Part at 1A Auto* 1aau.to/m/Shop-TRQ-Parts
√ *Do it Yourself*
√ *Save Money*
When he pulled the power window switch assembly at beginning he broke the front mount, it is an inside screw remove.
Yup, broke mine thanks to this video 😖
You would think after he made 4 or 5 videos (maybe even more than that) of having to remove the switches and door panel for various things wrong in there he would figure out that unless the switch panel needs to be replaced there is no need to take it off the door panel anyways. Just unplug it and leave it on the door panel. The 2002 and older has clips on the side and can be removed without taking the whole door panel off.
Awesome man thanks for the effort showing us how to do this stuff right 💪🏽
What i was wondering is,,, I have a plain jane chevy silverado roll up and manual non power doors with no heated mirrors. Is my truck pre wired for heated mirrors? Or do I have to buy some kit to have heated mirrors? Any ideas?
Thanks for the video. I appreciate it.
I just did mine , great Video thank you so much.
Straight to the point. 👍💯
Thank you so very much!
This type of side mirror is also good for 2005 chevy silverado 1500 right? Was planning to change mine as well
that's what i like, action and to the piont, thanks for the info
Clippie and hookiedo. Words of the day
And forkie tool can’t forget that one
massss puuuuutoooooo
Beautiful video.
❤ excellent good job
Best instructional video I have ever watched!
I'm trying to switch my 05 silverado mirrors with no arrows for a set off a 05 chevy suburban with arrows on mirrors....will it fit and why is the suburban mirror have shorter wire and on the video the wire is all the way to switch.....
On my 2005 Suburban LT, when removing what the mechanic in this video calls at 0:23 seconds into replacing the mirror "We're going to move along to this right here...", which is removing the switch cluster, where the electrical cables connect, he has this procedure out of order time-wise and is also incorrect in assuming it's only held in place by "clippy-do's", as there is a 7mm screw that secures the forward part of the switch cluster to the door panel that must be unscrewed FROM THE INSIDE OF THE DOOR PANEL AFTER THE DOOR PANEL IS REMOVED. On the vehicle in the video, both the back and front "clippy-do's" and the screw are broken, so it comes out without a problem. You can see the tip of the screw sticking up at 0:40 sec thru 0:44 sec, and at 0:49 sec thru 0:56 sec in this video. You can remove the back part of the switch cluster by using a plastic trim tool, but if you persist in forcing the front part out with it, or a stiffer metal pry bar, you're going to break that portion of the switch cluster that the screw fastens to. Frankly, the switch cluster doesn't need to be removed to replace the mirror as only the very rear black connector and the blue connector need to be disconnected and replaced. I was able to remove them working from the top down from outside my Suburban through the open window after all the panel securing screws, lock and door handle bezels had been removed, and I also didn't need to disconnect the door courtesy light connector as is done at 2:21 thru 2:31 in this video. Maybe there are switch clusters that don't have screws securing them on earlier models, but on my 2005, and on the vehicle in this video, the switch cluster is definitely secured with both "clippy-do's" and a 7mm screw...and there's actually no need to remove the switch cluster from the door panel, nor remove any other electrical connectors from it other than the two previously mentioned black and blue connectors for the mirror.
My truck too. Broke the front clip 🤨
Beware of any so called helpful information from anyone that uses the word clipping dos throughout video
Man you should’ve done the video instead 🥹
You're wrong on removing small plastic
pedastel with switches because my 2003 GMC had a 7mm screw in the front, which of course pulled out when i pryed the part of as you said, there are no covered screws or plastic pins either on this door , only 1 screw in the bottom. Just lift up panel and pull.
So @TRQ. When will your tech be sending me a new switch panel?
Thank you
thank you
What it was wrong with the mirror?? Because on my truck the mirror soon as a turn the key on the mirror turn into dark blue
Is the plug an 8 pin connector?
Does anyone know if you can switch out the regular bulbs for LEDs 🤔🤔🤔
In the 04 LT Tahoe there is a screw in that plastic that i just broke from removing switch covers from the door panel... thanks pal
+Whiteman Eric This video is applicable to a 1999-2007 Chevy Silverado. This procedure might be different for your application.
@@TRQ thats true but i was basically putting up a warning for others, of what a tahoe2004 has thats different. Your door panel looks the same as mine . We are learners before teachers..teaching helps me remember as i pass it on to others
+Whiteman Eric Thanks for the tip! 1aau.to/m/Shop-TRQ
Mine is a 2004 Silverado… definitely a screw at the front. Definitely broke it
I would have put thread lock on the replacement mounting screws since the new mirror didn't have the plug tabs to keep the mirror locked in
What if my light still don’t blink the mirror moves and everything but the blinker don’t work
can you just replace the glass in those or do you need the whole mirror
The power window sometimes has screws holding it in. It depends on the year of the vehicle. Just remove the door panel first to see if yours has screws holding that assembly together or you'll break it.
Mine doesn't have power anything so it's super easy to change, don't have to take off the whole panel just the little triangle piece.
LS models get the power mirrors
That's what I was thinking. Doing this tomorrow. Broke my mirror by accident. Looks straight forward for my 03 Silverado
You need to mention that when you remove electric window door lock and mirror component you will almost certainly break the plastic slot and pin that connects to door panel. After I broke the one on the drivers door I decided it was not necessary to remove per your video. You even mentioned that they were broken when you put it back together because you broke them when you removed it is why. Installers beware of this. Thumbs down because of this.
Yeah you can't really remove that without removing the door panel first. I've seen the proper way in other you tube videos.
do you mind explaining exactly how it’s done? i don’t wanna break the plastic slot & pin.
does this mean i shouldn’t disconnect that master switch? just take the whole door panel off, and then disconnect the wires?
Where are you located so I can bring my brand new 2006 Chevtolet Silverado so you can do it for me?? I’m in L A county
+Pablo Barrera We do not do repairs on customers vehicles at this time. We are based out of Massachusetts!
Completely did not show the only part i want to see is how to unconnect the wire inside the mirror so i can plug it into a new mirror
Mine was totally missing but it should be behind the triangle where the mounting hardware is has a retainer clip to lift to release.
that's not usually done. to be fair.
This guy literally removed the power switches that literally come off with that door panel. Let alone breaking it in the process of prying it up.
when he removed the window and lock switch panels he broke a screw and so did i on my truck
Me "put the connection behind the mirror so you don't have to take all that other stuff off"
Chevy "that makes alot of sense...NO"
Hookey-do lol
Bro you don’t have to take the whole panel off is this like a joke video or something?