Although I've been airbrushing for years, I still found this really helpful. Distances, PSI and thinning ratio information is extremely helpful. Thanks
@@robk5865 I had all kinds of issues until I found that tip on UA-cam. It lays out nice now with no orange peeling or other issues. Also dries very fast.
That was a great 'how to video', with my Tamiya paint, I always have two jars of the same colour, one thinned and the other jar, non thinned, I always pre thin with their own thinner and fill the jar up to judt below the top, this is idea eas from Andy's Hobby Headquarters and it works a treat, best regards from a Kiwi living in Australia
Thanks for this tutorial. Very helpful. Perhaps you could also do one on fillers and putties. It is a difficult area for the beginner. I look forward to your next build.
This short but much effective advise "on air-on paint-off paint-off air" helped me a lot to get rid of the splattering. Also to remove the needle out front was a good tip. Thanks mate!
Great video and some very helpful stuff. After a number of years I have now stuck with the Tamiya acrylic paint for spraying and Vallejo paint for brushing. I also always prime my models with Tamiya rattle can Surface Primer as this seems to stick well to the plastic and also the acrylic sticks really well to the Surface Primer. Without priming I have had the paint wear off the model through touching. It seems to make the paint much more robust. Finally for cleaning the airbrush after the Tamiya acrylics I find Wynns carburetor cleaner superb. It destroys the paint and a large aerosol of it is not very expensive. Its available in most automotive outlets. It does not affect airbrush seals.
Thanks - very useful. Interested in the Iwata Eclipse but all the ones I can see for sale online are marked 'Japan WM' whereas yours is 'Japan z8' - do you know if there is any difference please?
Very good video and explanation regarding paints and thinners to. I have a question: ist true that new atom paints from mig can be deluded with IPA (isopropyl alcohol) just like tamiya paints??
I wish someone had gone over the basics about airbrushing when I was starting out a few years ago. You did a good job, Andy. My favorite airbrush is also the Iwata HP-CS. I didn’t know that tip about removing the needle forward vs back. A side note: this is the first time I’ve seen you in person & you’re not what I imagined. In my mind I had you as a thin, nerdy dude for some reason. Ha ha.
No matter what airbrush I use, Iwata Revolution HP-CR3, Iwata Revolution HP-CR, Iwata HP-BH, Harder and Steenbeck Infinity CR Plus or the Evolution or what thinner I use I still have trouble with the AK Gen 3 paints, it splatters , blocks up, turns to some horrible gluggy mess in the air brush even using AK 3rd gen thinner. The days I was trying to spray it, it was 35C+so I'm wondering if there's a temperature limit on the paint.
This was really helpful and thank you. A good accompanying video could be surface preparation and how to get "good" first coat. Also (and apologies for burdening) perhaps how to correct common errors 🌞
Great video! I've been thinking about playing around with making some build videos as I begin my modelling journey. Any chance of seeing a behind the scenes video on how you do all this? ☺️ I'm super curious how your camera is set up.
I appreciate this video - I have been airbrushing for about 6 years (I self taught myself) and I see that what you just showed confirms that I am doing my painting correctly. Which airbrush and which needle did you use in this video? New subscriber - Henry Clayton, Nothern Calif, USA
What about air compressor recommendations and settings? As someone who hasn't airbrushed before I have no idea what size and psi is appropriate for model work, or what effect the changing of psi has on the paint
Really informative video , Thank you for taking the time to show us newbies some of the tips and downfalls of airbrushing I do have one question though I tend to use mainly Tamiya paints , but also i have quite a bit of the Vallijo model colours aswell and if the model that in building requires me to mix different paints is it ok to mix Tamiya and say a vallijo if i do not have the exact colour needed in Tamiya but do have equivalent colour in vallijo . Many thanks for your help .
Hi, thanks for your video. Just starting out and want to buy an airbrush… I was looking at the Vallejo model air paints that come in a set of most colours for German armour. Do these require thinning or can they go straight into the air brush? Thanks in advance
Enjoyed this as a yet to be modeller although you went through the various paint types a little too fast for me. The main take away was that water based were the least toxic and therefore easiest to start with for those not equipped with a spray booth and extraction. Would have also liked some advice on the various compressors available. Your sounded quite noisy in the background!
Hi great video! When i airbrush my models, no matter how hard i try to to get paint mixture and air pressure right, the paint still kind of specles. Smal dots gets scattered. The airbrush is cleaned with care altough has a couple of years of use now. I know it is hart to guess without seeing the results but am I still doing something wrong or could it be that the needle or nozzle is not smooth anymore?
AK real color is pretty dank (the solvent based stuff), it even mixes well with Tamiya and Mr Color (my local hobby shop has a huge selection of AK) but the AK thinner stinks. MLT makes it go on real nice.
I'm starting with airbrushing and don't get the ratios of thinning the paints right. I use atom paints, when he said that thinnint 25% is it meant to use 25% of paint or 25% thinner in the mix? My paint is often way to runny and I'm almost always ruin my paint job. I'm painting aluminium enclosures, which I prime with One Shot Primer. When I figured out the paint/thinner ratios I would paint my build models. Would be nice if someone could give me a tip.
Did that 10 drops of thinner and 10 drops of paint create enough paint to cover that complete model? What do you usually do with any excess thinned paint?
So you can spray solvent base over water base and visa versa thats what I needed to know because I'm a painter for over 20 years and with house paints latex and oil base paints will not work together without priming over with special primers 1st otherwise will have major problems . I bought an airbrush setup like 15 years ago used it a few times then put it away to busy but I just started getting back into it and am about to to an 1/18 scale huey and couldn't find the info anywhere if can paint with solvent for OD Green and use acrylic for everything else since thats what I already have .. please let me know if that is right or should just go buy more and do all with same kind of paints thanks for the info
hello, i'm thinking about switching to air brushing since i got some time with the brush, and i'd like to start using my own colours instead of those furnished with the model. Would you have any tips, brands or ways to see and acquire those. For example lets say i need green and white and you dont have any. Do you simply go on the desired brands website and order? Maybe it's better to go directly to a modelling store? I think the question is rudimentary but hey here i am and i've got a m2000 waiting to be painted. Thank you very much!
7:03 you might need to clean that air valve. There's probably gunk like old grease or paint stuck on top of the valve rod It shouldn't stick on for that long. Air should be immediate on or off. It unscrews out from the bottom in my HP-CS. Great video.
Overall very nice tutorial. I do disagree with removing the needle from the front. I started airbrushing in the late 1970's and learned that anytime you remove the nozzle you are breaking the seal there and inviting air leaking back into the cup and poor spray performance. And if you have cleaned your airbrush properly Before removing the needle, there will Not be any paint either in the paint passages or dried on the needle to cause any problem extracting to the rear. Most modern airbrushes use a PTFE packing/needle bearing and should wipe any soft paint off the needle. Again if properly cleaned before removal there should be only a very slight very wet layer on the needle but mostly just cleaner.
A little critique if I may... You're getting more "skinning" inside the cup than necessary by backwash mixing the paint/thinner in there. I'm sure you're not having issues and that's why you use this method, but why propagate more potential globs of paint skin schmoo? It can ruin anyone's spray pattern real quick.
Thank you for the lesson really very helpful. Would you recommend tightening the screw behind the needle to help with more control over the amount of paint your spraying
Number one lesson for airbrushing is buy a high quality airbrush. If you start out with a Amazon $30 airbrush you will fail. I've been airbrushing for more than 50 years and the story never changes. Practice, practice and practice is the key to learning. You'll get to the point where you don't even have to think what to do, you just spray away.
@@Scott-w2b Probably. However... nobody needs to be reminded to like and subscribe. You don't, do you? I know I certainly don't. It's like being reminded to put a filter in your coffeepot every morning before you make coffee. And to add the ground coffee and the water. Just stop. Only the real nOoBz to UA-cam might need to be reminded... once. People catch on really fast. Upshot: if someone isn't subscribed, then they don't want to be subscribed. Likewise, people tend to "like" the things that they actually like. Nobody should upvote anything that they don't like better than neutral.
Although I've been airbrushing for years, I still found this really helpful. Distances, PSI and thinning ratio information is extremely helpful. Thanks
Mr. Color leveling 400 is the key to spraying the Tamiya acrylic . 75% thinner 25% paint works well.
I can't believe how well that thinner works. Tamiya acrylics shoot beautifully with it. And yes, thin! Tonal variations are a breeze at 70-30 for me.
@@robk5865 I had all kinds of issues until I found that tip on UA-cam. It lays out nice now with no orange peeling or other issues. Also dries very fast.
MLT is hands down the best thinner with every solvent based paint.
After 50+ years of airbrushing Mr.Color is the only way to go. Tamiya's thinner is just a waste of money.
@@joemoore4027 yes I found out the hard way.
Great tip about removing the needle from the front of the airbrush when cleaning.👍
FINALLY heard explanation of why folks will call Tamiya, AK Real Colors "acrylics"- it's not due to the carrier / solvent but rather the pigment. THX
Great video Andy. It’s great to see some simple but interesting info without pointless waffle.
That was a great 'how to video', with my Tamiya paint, I always have two jars of the same colour, one thinned and the other jar, non thinned, I always pre thin with their own thinner and fill the jar up to judt below the top, this is idea eas from Andy's Hobby Headquarters and it works a treat, best regards from a Kiwi living in Australia
Thanks for this tutorial. Very helpful. Perhaps you could also do one on fillers and putties. It is a difficult area for the beginner. I look forward to your next build.
Nice one Andy I must learn not to remove needle out the back on my eclipse really bad practice
Thanks Andy! Great video as usual! Thanks for the advice on weathering when I visited yesterday!
Спасибо, отличное видео для новичков. Мне как среднему моделисту было интересно смотреть. Удачи и новых видео👍✊️
That was brilliant Andy, thank you. I look forward to more ‘how to videos’👍.
Good! Nice to see that you tell people the proper double action technique 👍
Thanks Andy, great video, you made airbrushing look so easy.
Brilliant video Andy! Hope to see more tutorials from you👍
Thank you for a very informative video. Just purchased my first air brush on Amazon for my model trains.
This short but much effective advise "on air-on paint-off paint-off air" helped me a lot to get rid of the splattering. Also to remove the needle out front was a good tip. Thanks mate!
I just ordered an airbrush thanks for the video.
Great video and some very helpful stuff. After a number of years I have now stuck with the Tamiya acrylic paint for spraying and Vallejo paint for brushing. I also always prime my models with Tamiya rattle can Surface Primer as this seems to stick well to the plastic and also the acrylic sticks really well to the Surface Primer. Without priming I have had the paint wear off the model through touching. It seems to make the paint much more robust. Finally for cleaning the airbrush after the Tamiya acrylics I find Wynns carburetor cleaner superb. It destroys the paint and a large aerosol of it is not very expensive. Its available in most automotive outlets. It does not affect airbrush seals.
Nice change of video - thanks for the tips!
Thanks for the price point comparison of the three airbrushes and the qualities and benefits.
Thanks - very useful. Interested in the Iwata Eclipse but all the ones I can see for sale online are marked 'Japan WM' whereas yours is 'Japan z8' - do you know if there is any difference please?
Very good video and explanation regarding paints and thinners to.
I have a question: ist true that new atom paints from mig can be deluded with IPA (isopropyl alcohol) just like tamiya paints??
I wish someone had gone over the basics about airbrushing when I was starting out a few years ago. You did a good job, Andy. My favorite airbrush is also the Iwata HP-CS. I didn’t know that tip about removing the needle forward vs back. A side note: this is the first time I’ve seen you in person & you’re not what I imagined. In my mind I had you as a thin, nerdy dude for some reason. Ha ha.
This is a very useful and informative little video.
Thanks mate, very helpful
so helpful! thanks for the info. The bit on panel lines is such a good idea. Goping to give my airfix 1:72 Mosquito B XVI this treatment
My question is how do you determine how much paint to use? Dumb question but I'm looking to start airbrushing for the first time
very helpful and informative , THX
Great video! Learned a lot, I have 2 airbrushes
I find them hard to use. I need to use them more so I can get better. Practice makes perfect.
Thanks
Awesome! A quick question: do you use a mask for respiration protection?
Great tips.😊
No matter what airbrush I use, Iwata Revolution HP-CR3, Iwata Revolution HP-CR, Iwata HP-BH, Harder and Steenbeck Infinity CR Plus or the Evolution or what thinner I use I still have trouble with the AK Gen 3 paints, it splatters , blocks up, turns to some horrible gluggy mess in the air brush even using AK 3rd gen thinner. The days I was trying to spray it, it was 35C+so I'm wondering if there's a temperature limit on the paint.
The AK gen 3 paints ate acrylics rigt? I also had problems spraying them. What I noticed is that you have to mix it very well with its thinner.
This was really helpful and thank you. A good accompanying video could be surface preparation and how to get "good" first coat. Also (and apologies for burdening) perhaps how to correct common errors 🌞
the iwhata is very cool O_o the nosel is very spezial.
... the nozzle* is very special*.
Great video! I've been thinking about playing around with making some build videos as I begin my modelling journey. Any chance of seeing a behind the scenes video on how you do all this? ☺️
I'm super curious how your camera is set up.
I appreciate this video - I have been airbrushing for about 6 years (I self taught myself) and I see that what you just showed confirms that I am doing my painting correctly.
Which airbrush and which needle did you use in this video?
New subscriber - Henry Clayton, Nothern Calif, USA
Great video!
Great knowledge. Very informative. Thank you for sharing.
What about air compressor recommendations and settings? As someone who hasn't airbrushed before I have no idea what size and psi is appropriate for model work, or what effect the changing of psi has on the paint
Really informative video , Thank you for taking the time to show us newbies some of the tips and downfalls of airbrushing I do have one question though I tend to use mainly Tamiya paints , but also i have quite a bit of the Vallijo model colours aswell and if the model that in building requires me to mix different paints is it ok to mix Tamiya and say a vallijo if i do not have the exact colour needed in Tamiya but do have equivalent colour in vallijo . Many thanks for your help .
Hi, thanks for your video. Just starting out and want to buy an airbrush… I was looking at the Vallejo model air paints that come in a set of most colours for German armour. Do these require thinning or can they go straight into the air brush? Thanks in advance
Please explain the various paint brushes you use
Enjoyed this as a yet to be modeller although you went through the various paint types a little too fast for me. The main take away was that water based were the least toxic and therefore easiest to start with for those not equipped with a spray booth and extraction. Would have also liked some advice on the various compressors available. Your sounded quite noisy in the background!
Hi great video!
When i airbrush my models, no matter how hard i try to to get paint mixture and air pressure right, the paint still kind of specles. Smal dots gets scattered. The airbrush is cleaned with care altough has a couple of years of use now. I know it is hart to guess without seeing the results but am I still doing something wrong or could it be that the needle or nozzle is not smooth anymore?
AK real color is pretty dank (the solvent based stuff), it even mixes well with Tamiya and Mr Color (my local hobby shop has a huge selection of AK) but the AK thinner stinks.
MLT makes it go on real nice.
I'm starting with airbrushing and don't get the ratios of thinning the paints right. I use atom paints, when he said that thinnint 25% is it meant to use 25% of paint or 25% thinner in the mix?
My paint is often way to runny and I'm almost always ruin my paint job.
I'm painting aluminium enclosures, which I prime with One Shot Primer.
When I figured out the paint/thinner ratios I would paint my build models.
Would be nice if someone could give me a tip.
Good information
You can thin Tamiya and Ak real colour with IPA
Did that 10 drops of thinner and 10 drops of paint create enough paint to cover that complete model? What do you usually do with any excess thinned paint?
Great content
Good tutorial
Great video
You really hepl me a lot!!!
Please could you tell me, how much compressor psi usually use when airbrushing? (sorry for bad englsih)
Great vid! Thanks, how often would you dismantle the airbrush to clean it ?
So you can spray solvent base over water base and visa versa thats what I needed to know because I'm a painter for over 20 years and with house paints latex and oil base paints will not work together without priming over with special primers 1st otherwise will have major problems . I bought an airbrush setup like 15 years ago used it a few times then put it away to busy but I just started getting back into it and am about to to an 1/18 scale huey and couldn't find the info anywhere if can paint with solvent for OD Green and use acrylic for everything else since thats what I already have .. please let me know if that is right or should just go buy more and do all with same kind of paints thanks for the info
hello, i'm thinking about switching to air brushing since i got some time with the brush, and i'd like to start using my own colours instead of those furnished with the model. Would you have any tips, brands or ways to see and acquire those. For example lets say i need green and white and you dont have any. Do you simply go on the desired brands website and order? Maybe it's better to go directly to a modelling store? I think the question is rudimentary but hey here i am and i've got a m2000 waiting to be painted. Thank you very much!
Ive got a Fendga and somehow it works even better than my HS Infinity ever did. Have you tried one before Andy?
please help! i dont get one thing if i use thinner with tamiya paint, with what product i need to clean my airbrush? thank u!
What about Compressors ?
I would welcome a “painting 1/48 pilots” tutorial. They always let me down.
7:03 you might need to clean that air valve. There's probably gunk like old grease or paint stuck on top of the valve rod It shouldn't stick on for that long. Air should be immediate on or off. It unscrews out from the bottom in my HP-CS. Great video.
Overall very nice tutorial.
I do disagree with removing the needle from the front. I started airbrushing in the late 1970's and learned that anytime you remove the nozzle you are breaking the seal there and inviting air leaking back into the cup and poor spray performance. And if you have cleaned your airbrush properly Before removing the needle, there will Not be any paint either in the paint passages or dried on the needle to cause any problem extracting to the rear. Most modern airbrushes use a PTFE packing/needle bearing and should wipe any soft paint off the needle. Again if properly cleaned before removal there should be only a very slight very wet layer on the needle but mostly just cleaner.
How long do these paints take to dry ? Not done any airbrushing yet.
A little critique if I may...
You're getting more "skinning" inside the cup than necessary by backwash mixing the paint/thinner in there. I'm sure you're not having issues and that's why you use this method, but why propagate more potential globs of paint skin schmoo? It can ruin anyone's spray pattern real quick.
Can someone tell me where I can get a good starter kit?
Thank you for the lesson really very helpful. Would you recommend tightening the screw behind the needle to help with more control over the amount of paint your spraying
Great video Andy, my seam line work needs improving so can that be a future video please ?
It is possible to explain the difference in the size of the needles: 1.5, 2.00, and 3.00.
Number one lesson for airbrushing is buy a high quality airbrush. If you start out with a Amazon $30 airbrush you will fail. I've been airbrushing for more than 50 years and the story never changes. Practice, practice and practice is the key to learning. You'll get to the point where you don't even have to think what to do, you just spray away.
Not true master airbrush is used by multiple pros that paint rc bodies 4 the top names
You have no idea how much your audience despises being reminded to like and subscribe.
If people didn't like and subscribe he wouldn't be making these videos
@@Scott-w2b Probably. However... nobody needs to be reminded to like and subscribe. You don't, do you? I know I certainly don't. It's like being reminded to put a filter in your coffeepot every morning before you make coffee. And to add the ground coffee and the water. Just stop.
Only the real nOoBz to UA-cam might need to be reminded... once. People catch on really fast.
Upshot: if someone isn't subscribed, then they don't want to be subscribed. Likewise, people tend to "like" the things that they actually like. Nobody should upvote anything that they don't like better than neutral.
@timhofstetter5654 I rather hear like and subscribe then read whatever you wrote
@@Scott-w2b You do you.
Some of us need to be examples for the rest.
A MAC valve does nothing to the air pressure. It only alters the air flow rate.
Mask of the lines they will be more sharp
You don’t have to love the needle forward to remove it. In fact, in some airbrushes you can’t.
'Promosm'
👏👏👏💪💪💪