I just ordered 2 of these for $15 each. They will be here this friday. I just watched this video tonight.😂😂😂. I suspected that what they claimed was too good to be true and almost choked on my coffee when i saw that the one in your video was the type i purchased... If its the same quality then im satisfied. It would have been sweeter if it was actually 1500 watts but i cant complain too much
What FET was that? I was looking for Rds in the datasheet but didn't catch that. Because that's what burns them eventually. Low Rds means less heat at high current. Also the heat dissipation (the heat it can take out quickly enough to save itself) is 140W in the datasheet which is not good for a quality FET, I think these FETs have RDs over 10 milli ohms which is mid range. You better make your own with good FETs like IRF3077. Thanks for the review. I just bought it myself.
Hey mate great video, im struggling with connecting this controller, would you have a diagram of it? All i want from it is a throttle with key and volt meter and i cant get it too work
V x a = watts 71v x 20a = 1420w 30a would give you over 2000w at 71v So there advertising is correct Ive shuntmodded these china controllers before with no issues pulling 35-40amp You just have to be carefull These controllers make for a noisy motor if i have to complain about anything
I agree. I've fiddled with a 15fet versions "35a 1500watt 48v" shunt mod and it draws 50amps no worries barely gets warm bike goes 70kmph on 56v pack 63v with a full charge
bonjour, le câble du moteur de mon scooter 50 cm2 ces pris dans une rainure de la roue. ce qui a sectionner un des cables. depuis l'ecran s'allume mais l'acceleration ne marche pas . et le controleur emet un sifflement . est ce reparable ? mille merci
Hey you have two single wires it comes out of your speed controller box and another one goes out of your speed controller box on the ends of those wires there's a mail in and a female in you must connect those two to each other so it goes up the box and back down the box you know out of the box then back in the box it sounds ridiculous but if you want to go above 48 you connect it then it knows that you're going to go 48 volts or 60 or 72 or whatever
Mine was double the size as yours and mine was 1000 watt 35aml controller and yours is 100% not 1000w but I have seen smaller ones which are 2000w think its called phase runner
Hello my name is Paulo chapel, friend help me with a brushed controller d 30 vts 500w 28 A. of the brand XUN. I don't know how to connect this device, on the accelerator with a contact key, this accelerator has 5 wires (On Throttle Socket: Green, Black and Red) (separator: 2 wires; Yellow and blue.) This throttle has a motorcycle key and battery indicator. on the brush controller there is a white socket written: (Derailleur) in the colors green red and preto. I already know it's the accelerator but what about the two yellow and blue wires???? where can i plug it in?? we have two blue wires in a white socket written lock two blue wires written lock; what are these two wires for?
Nice video, thanks. I clicked the amazon link, and the price that pops up is 48 dollars. I'm in the Netherlands btw. You mentioned in the video that it actually costs 25 but you wanted it the next day, so you payed 50 (or something like that). Is the price geo-dependant maybe?
Hi mate iam looking for a new controller 1500w to 2000w I was using the Voldemort loved the acceleration and torque. After I did the shunt and tracer mod but stopped working.After about a year or so I got a kt controller and display 1500w to 2000w was shit so I sold it do you know any on the market that is similar to the Voldemort that as proper working pedal assist
Greetings. Does this controller charge its batteries (via charger), or you need an extra ''board'' as external module for charging batteries?. Thank you in advance.
yeah I agree I like them because it's cheap and I tear up my electric scooter faster than my controller 😂 anyway I set mine for full power one button take off
lol it is programable you need to choose what volt your using. these controllers have a internal programable area they are very adaptive.
I just ordered 2 of these for $15 each. They will be here this friday. I just watched this video tonight.😂😂😂. I suspected that what they claimed was too good to be true and almost choked on my coffee when i saw that the one in your video was the type i purchased...
If its the same quality then im satisfied. It would have been sweeter if it was actually 1500 watts but i cant complain too much
What FET was that? I was looking for Rds in the datasheet but didn't catch that. Because that's what burns them eventually. Low Rds means less heat at high current. Also the heat dissipation (the heat it can take out quickly enough to save itself) is 140W in the datasheet which is not good for a quality FET, I think these FETs have RDs over 10 milli ohms which is mid range. You better make your own with good FETs like IRF3077.
Thanks for the review. I just bought it myself.
Thank you for your work doing this review
Wtf why did you repeat 500 watt multiple times when watts is amps by volts if it says its 26 by 60 volts your numbers are wrong
Hey mate great video, im struggling with connecting this controller, would you have a diagram of it? All i want from it is a throttle with key and volt meter and i cant get it too work
Did you ever figure out what the low voltage cut off was?
V x a = watts
71v x 20a = 1420w
30a would give you over 2000w at 71v
So there advertising is correct
Ive shuntmodded these china controllers before with no issues pulling 35-40amp
You just have to be carefull
These controllers make for a noisy motor if i have to complain about anything
I agree. I've fiddled with a 15fet versions "35a 1500watt 48v" shunt mod and it draws 50amps no worries barely gets warm bike goes 70kmph on 56v pack 63v with a full charge
YOUR AWSOME ENGINEER.
bonjour, le câble du moteur de mon scooter 50 cm2 ces pris dans une rainure de la roue. ce qui a sectionner un des cables. depuis l'ecran s'allume mais l'acceleration ne marche pas . et le controleur emet un sifflement . est ce reparable ? mille merci
Great vid thanks for sharing.
Hey you have two single wires it comes out of your speed controller box and another one goes out of your speed controller box on the ends of those wires there's a mail in and a female in you must connect those two to each other so it goes up the box and back down the box you know out of the box then back in the box it sounds ridiculous but if you want to go above 48 you connect it then it knows that you're going to go 48 volts or 60 or 72 or whatever
Mine was double the size as yours and mine was 1000 watt 35aml controller and yours is 100% not 1000w but I have seen smaller ones which are 2000w think its called phase runner
please which cable wires for display and which disply i can use here , thank you
How did you get the power lock to work
I RECOGNIZE THIS CONTROLLER I USE ONE AND IT IS 500 WATTS AND MADE FOR MINI ATV I HAVE FOR MY SON IT IS CHINA MADE AND GOOD FOR 36v SMALLER VEHICLES
Can this controller be use in a 72v battery pack with 84v max charge?
Hello my name is Paulo chapel, friend help me with a brushed controller d 30 vts 500w 28 A. of the brand XUN.
I don't know how to connect this device, on the accelerator with a contact key, this accelerator has 5 wires
(On Throttle Socket: Green, Black and Red)
(separator: 2 wires; Yellow and blue.) This throttle has a motorcycle key and battery indicator.
on the brush controller there is a white socket written: (Derailleur) in the colors green red and preto. I already know it's the accelerator but what about the two yellow and blue wires????
where can i plug it in?? we have two blue wires in a white socket written lock two blue wires written lock; what are these two wires for?
Nice video, thanks. I clicked the amazon link, and the price that pops up is 48 dollars. I'm in the Netherlands btw. You mentioned in the video that it actually costs 25 but you wanted it the next day, so you payed 50 (or something like that). Is the price geo-dependant maybe?
Hi mate iam looking for a new controller 1500w to 2000w I was using the Voldemort loved the acceleration and torque. After I did the shunt and tracer mod but stopped working.After about a year or so I got a kt controller and display 1500w to 2000w was shit so I sold it do you know any on the market that is similar to the Voldemort that as proper working pedal assist
Is it include with regenerative braking
no
Greetings.
Does this controller charge its batteries (via charger), or you need an extra ''board'' as external module for charging batteries?.
Thank you in advance.
No brushless controller can charge the battery, you'll always need a BMS or balance leads and a hobby charger to charge lithium.
hola necesito ayuda, me puede ayudar , tengo un motor 36v 1000w me llego sin la bateria
So what's the gig? 500 watt?1500 watt?.....48 or 64 volt ?or did you just get suckered to by 2 pieces of junk?
This controller can run more then one voltage. 48v and 64 I’ve personally used with this controller
running 79v each
Depends on what battery you can use, the controller must have large enough Capacitors too function correctly not 🔥
أرغب في شراء دائرة كونترول لسكوتر 48 فولت
yeah I agree I like them because it's cheap and I tear up my electric scooter faster than my controller 😂 anyway I set mine for full power one button take off
can i use 1500w controler with 500w motor
Yes if same design /wave
did you make your battery pack?
DIY batt packs are the only way to go ☺️
1
Can I use 48v 1000W controller on 12v battery? 🛴
no minimum is 24v and that only if you remove the lvc. tested it in the past and it works.