How to Replace Upper Control Arm 2000-2006 Chevy Tahoe

Buy Now!
New Control Arm with Ball Joint from 1AAuto.com 1aau.to/ic/1ASF...
Control arms are a crucial part of the suspension system of your vehicle. They not only carry the load of the vehicle to the wheel, but they typically also maintain its alignment. Control arms are typically large and strong, so you may be surprised it needs replacing. They contain rubber bushings for smoother rides at the cost of eventual wear, or integrated ball joints that require replacing the entire arm when they wear. This video shows you how to install a new quality TRQ lower control arm with ball joint in your 2000-2006 Chevy Tahoe.
• Check here for more videos on the 2000-06 Chevy Tahoe • Chevy Tahoe 2000-06 2n...
This process should be similar on the following vehicles:
2000 Chevrolet Tahoe
2001 Chevrolet Tahoe
2002 Chevrolet Tahoe
2003 Chevrolet Tahoe
2004 Chevrolet Tahoe
2005 Chevrolet Tahoe
2006 Chevrolet Tahoe
Tools you will need:
• Pry Bar 1aau.to/oem/1AX...
• 21mm wrench
• 10mm Socket 1aau.to/ont/1AX...
• 18mm Socket 1aau.to/ogX/1AX...
• 22mm Socket 1aau.to/oaS/1AX...
• Trim Tool Set 1aau.to/oeT/1AX...
• Ratchet 1aau.to/orj/1AX...
• Torque Wrench 1aau.to/ojw/1AX...
• 13/16 Inch Wrench
• Gloves 1aau.to/obH/1AX...
• Safety Glasses 1aau.to/oa8/1AX...
• Floor Jack 1aau.to/oeH/1AX...
• Ratchet Strap
• Wheel Chocks
Subscribe: / @trq
Check out our playlist:
Chevy Tahoe 2000-06 2nd Generation: • Chevy Tahoe 2000-06 2n...
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

[@TRQ]

√ *Watch the Video*
√ *Buy The Part at 1A Auto* 1aau.to/m/Shop-TRQ-Parts
√ *Do it Yourself*
√ *Save Money*

[@Fhqwhgads00]

I must have watched this like 5 times while changing my upper control arm. Excellent video!

[@truthhurts4771]

Do not forget to install a cotter pin through the ball joint crown nut.

[@timclone3757]

What if the upper control arm shackles are rusted pretty thin? Is there a replacement part that can be welded in?

[@ericmendoza7629]

How come the control arm you installed has a grease fitting but the ones I ordered from yall dont?

[@jaysoncolbert6187]

It's a conspiracy thing

[@charlesshepherd7964]

What if you forgot to set the cams on the upper control arm what do you do then

[@Jephro360]

You should get it realigned after that anyway

[@GetItGirlEnt]

What if my bolts want back out of the control arm where the cam screw are

[@user-dx9vd8fg7u]

Ok I bought these control arms from you guys through 1A auto and that bolt turns it has an Allen wrench fitting on the bottom with no room to get an Allen wrench in on top of the CV boot. This video shows him just tighten it like it’s nothing.

[@marcosg6406]

Might be too late but when it keeps turning just pry down on the control arm so that the ball joint gets stuck in the knuckle as you tighten.

[@angelbenavides5784]

Are the torque specs the same for a 02 suburban 1500?

[@coffeedollsvp]

Do i need to do this is if i crank my torsion key?

[@steelersnation4L]

Question for anyone that may know my truck passenger side tire won’t turn left or right at all but my driver side does the other day I was making a u turn and heard a loud pop.. I just had my pitman arms replaced on both sides any idea what it could be? I have a 03 Chevy Tahoe

[@kingpipiripaus8092]

If i put my 6 inch lift with the rc control arms they'll fit ??

[@kylepowell9829]

Are these ball joints replaceable or do I have to change the whole arm

[@misterm77]

Replaceable. But they ,at leason my Tahoe, are the type where the rubber boot must be pressed on the ball joints(uppers) also.

[@fizzybillylah3816]

Excellent!

[@kylepowell9829]

Can you change just the ball joint,or does the complete arm have to be replaced?

[@sharpie132]

Might as well change the whole thing out the bushings in the control arm go bad also. But to answer your question no you don't have to change the whole control arm out.

[@bassassin2695]

Im sooo glad i dont live in the north. I couldn't stand having to beat everything out like that 😂

[@net7rok]

You don't show jack placement

[@simbyy5486]

Mine rub right under the crow bar at the 5:05 mark

[@nutragardens6632]

I did this to my van .. chevy Express and now they say it needs a hole .. So I can get the wheel alignment... I dont understand

[@MuhammadAkram-nf2qs]

nice

[@troubledsoul764]

Do I need adjustable control arm or a non adjustable? 2005 Tahoe Z71 4wd

[@vamoneygroup]

Get a bent tube control arm. Should be about 200 bucks

[@charlesshepherd7964]

Service tire monitor

[@Jephro360]

It might be your tire pressure sensor

[@gabriel-bx7tz]

My wheels are cambered now so I did something wrong

[@charlesshepherd7964]

And what is it mean when it says service stabilizing system

[@Jephro360]

It might be your auto leveling system

[@misterm77]

Usually electronic struts

[@justindavenport8588]

What size bolt for the brake line that broke off? Mine broke as well.

[@AFatherToTheFatherless]

Just zip tie it

[@funrun508]

I don't like to hit the arm to lose

[@TRQ]

+DUB Thanks for the feedback! 1aau.to/m/Shop-TRQ

[@funrun508]

@@TRQ i have different tolerance hight in front side