A good idea is to paint the inside of the cut worktop with an acrylic or oil based paint. If there is an ingress of water and the exposed inner worktop is not sealed, it could start to expand.
It isn't done and dusted until you fix the clips in place - especially fun where you cut the base unit to fit the bowl. I have found that the clips supplied will need their own cut-out in the worktop (usuall 2-3mm) to enable the thickness of the clip to be accomodated. also on the thicker worktops longer screws may be needed for the clips. Its important to use EVERY clip position on the sink flange to ensure no leaks - I find that "pros" often leave out several clips if they are difficult to get at.
sink clips lift the worktop off the unit? do i have to notch out for them as well so it sits flat again? and if so whats the best way to do this? thanks really good video
Did you end up just using silicone instead and not bothering with clips? I used clips last time I fitted a sink and it was very awkward to do. I’m hoping to get away from using the clips next time.
A few more tips to add to an already comprehensive video - 1 Once the cutout's been done, fit the sink into the worktop via its clamping clips before you fix the worktops down, it's much easier than trying to do it lying on your back inside a cabinet. 2 - Same goes for the tap, overflow and waste plug/strainer - fit them in advance. Make sure your tap is nice and tight via the fixing nuts which are supplied, as these are often difficult to access for tightening if they become loose at some point in the future. Same goes for the flexi hoses for your hot and cold water. 3 - You'll sometimes find that when you've done the above and you put the sink back in its cutout, the sink clips catch on top of the cabinet, lifting the worktop slightly. If this happens, use a chisel just to take shallow notches out of the cabinet top until the worktop sits totally flat on the cabinet.
Sink manufacturers should just add the exact template one needs to cut out, all one should have to do is position template accurately and cut out around it!
Well the problem with most "do it this way" videos is they show an ideal case and the "easy" bits! In the real world the sink has to be fitted when the worktops have been mitred and fixed in position- you can't do this after fitting your sink - and the sink seal and fixing clips aren't mentioned. The drill was on hammer action to drill the starting holes for the jigsaw - and you only need holes in two corners - think about it! Otherwise a good clear presentation - better than most!
You don’t show how clips are going in. Especially onto that section where the cut out is basically flush with the unit’s back wall. I’d love to see how you do that
A simple job, thts gonna take 4 hours. By the time youve sealed the worktop fastened down the sink, fitted taps and waste, and then plumb into existing hot/cold and waste pipes.
No fair! I never saw a reptile! When somebody promises a "skink" they should deliver! Seriously, I'm getting ready to make upgrades in my kitchen but I'm doing granite countertops.
Carrying a worktop with a large hole in it could be problematic. Fitting and fixing the sink would make it stronger. Most cabinets for sinks do not have a top in them. Nice video.
Back in my days we didn't have the luxuries of internet or UA-cam, we had to use our brains, we had to have a high level of understanding by sight and the common sense to know what problems and dangers would be expected if the job wasn't carried out correctly unlike today 2019. 2012 is when you uploaded your video but you also gave advice on how to fuck-up on a inset sink fitting which explains why through the years so many second rate jobs and DIY jobs have caused so many problems and second rate workers. Your video is not how to fit a sink but how to do the cut out for the sink, the cut out and fitting a sink are 2 different facts also, your explanation and demonstration lacks details as to fitting a sink the most basic part of the job. My advice to people like you is understand details before giving advice to the people that don't know how to do these jobs, that fact alone is in the ending of your video when you set the sink into the cut out saying done and dusted, far from was it done and dusted, maybe in future you'll mention the sink seal and the clamping of the sink.
Great so where's your video buddy? Oh your didn't make one, just came here to bitch about a guy that took time out to help others. Suggest put your energy into something positive.
Well, you say that, but you've not actually installed it, as per the video title would suggest. What about undercounter seal and clips? Protection for the cut edges in the worktop and base unit? Preparation for taps and waste trap? Taps and waste fitting? You say it's easy, but that's probably because you've forgotten about all the additional work required to do a good job. Anything is "easy" if you ignore half the details. You could solve this very easily. Change the video title to "How to cut worktop for sinks and appliances".
foppo leeuwerke in this job is very important to have a GOOD quality tools. He claims to do it for long time but still have SHIT tools. It means that he lies or he's shit
I just followed your instructions exactly and it came out perfect. I'm relieved I haven't ruined £180 worth of worktop - thank you!
that's the most informative video I've seen on this subject
Great upload. I'm fitting my own kitchen today and this has really given me the confidence to have a go at putting the sink in. Thanks.
Opopp
The best instruction video I have seen.
Thank you for your time and help I appreciate 🙏🏻
Great tip with the spade bit!
A good idea is to paint the inside of the cut worktop with an acrylic or oil based paint. If there is an ingress of water and the exposed inner worktop is not sealed, it could start to expand.
It will definitely expand over time.
It isn't done and dusted until you fix the clips in place - especially fun where you cut the base unit to fit the bowl. I have found that the clips supplied will need their own cut-out in the worktop (usuall 2-3mm) to enable the thickness of the clip to be accomodated. also on the thicker worktops longer screws may be needed for the clips. Its important to use EVERY clip position on the sink flange to ensure no leaks - I find that "pros" often leave out several clips if they are difficult to get at.
Ahah this is what I was looking for! I can’t figure these clips out 😂
@@99hank97just silicone the sink fk the clips
Exactly 💯
Very good information Very easy to understand 👍
Thanks for the upload and great tip on the spade bit 👍
Watching videos on how to cut the hole out for my sink.. Great video thank you 😊
sink clips lift the worktop off the unit? do i have to notch out for them as well so it sits flat again? and if so whats the best way to do this? thanks really good video
Really helpful this mate thank you
Hi. Ready to cut out my new sink tomorrow? Would you recommend the standard sink clamps to fasten this to the work top or use silicone?
This is what I want to know - and also how to level it so that the water drains off the draining board and into the sink.
Did you end up just using silicone instead and not bothering with clips? I used clips last time I fitted a sink and it was very awkward to do. I’m hoping to get away from using the clips next time.
This is a very useful video. Step by step demo for my second kitchen but first re-using the sink which has no template available. Thank you Yves.
no mention that half the time the clips to tighten the sink down do not fall within the easy access area and extra routing is needed
The best video@! Thank you.
Lovely job, thanks for sharing 👍🏿
Great job, well done!
A few more tips to add to an already comprehensive video - 1 Once the cutout's been done, fit the sink into the worktop via its clamping clips before you fix the worktops down, it's much easier than trying to do it lying on your back inside a cabinet. 2 - Same goes for the tap, overflow and waste plug/strainer - fit them in advance. Make sure your tap is nice and tight via the fixing nuts which are supplied, as these are often difficult to access for tightening if they become loose at some point in the future. Same goes for the flexi hoses for your hot and cold water. 3 - You'll sometimes find that when you've done the above and you put the sink back in its cutout, the sink clips catch on top of the cabinet, lifting the worktop slightly. If this happens, use a chisel just to take shallow notches out of the cabinet top until the worktop sits totally flat on the cabinet.
Very useful tips - thanks.
How does the jigsaw blade avoid bashing into the wood frame underneath?
Great video, thanks
Very detail instructions
Another step would have been useful. Securing the sink to the worktop using clips and silicone sealant. Great no nonsense tutorial. Thanks
easier-said-than-done love it
Sink manufacturers should just add the exact template one needs to cut out, all one should have to do is position template accurately and cut out around it!
Most sinks include them now
mulțumesc pentru videoclipul util
What about the lack of support at the front of the sink? Is that not a weak spot now youve cut into the support bar?
Great vid... thanks💪
You moved the counter top after you cut out the hole? Isn't tht an easy way to have it fold in half when you move it?
very complete video,thanks
Nice job. Try drill the holes from the top and then as the point comes through the work top remove and gently drill upwards to prevent break out.
Well the problem with most "do it this way" videos is they show an ideal case and the "easy" bits! In the real world the sink has to be fitted when the worktops have been mitred and fixed in position- you can't do this after fitting your sink - and the sink seal and fixing clips aren't mentioned. The drill was on hammer action to drill the starting holes for the jigsaw - and you only need holes in two corners - think about it! Otherwise a good clear presentation - better than most!
why dint he make the sink cupboard 50mm so that he wouldnt need to cut it with a jig saw after cutting the worktop? Its time consuming
can i just use my old worktop as a temlate
@@paul-ne1bh As long as your your new sink is the same size as the old one, SMART!
Got the basic stuff right , but forgot sealing the cut edges of the worktop cut out !!
You don’t show how clips are going in. Especially onto that section where the cut out is basically flush with the unit’s back wall. I’d love to see how you do that
Usual dimensions are 50 to 60 millimeters (5-6 cm) from the front edge. Cut the hole 10 mm (1 cm) smaller all around.
Great video..
very good job I like it
Great, glad you found it useful : )
Does anybody have problems with jigsaw blades wearing down when a worktop is cut from the underneath?
Nice very good
THANK'S GREAT VIDEO.
Great video. Well done.
Do one with granite counter top
Cute and accurate
very good, thank you
Why not lay out masking tape first slightly bigger than the sink outline, then mark everything (sink profile and cutting profile) on it?
nice one
Can I use a regular 4 inch grinder to make the cut?
Thanks
A simple job, thts gonna take 4 hours. By the time youve sealed the worktop fastened down the sink, fitted taps and waste, and then plumb into existing hot/cold and waste pipes.
Good
Thank you.
You dropped the sink in but what about the caulking and clips?
its not done yet caulk or silicon sealant should be used or water will get inside the cabinet
No fair! I never saw a reptile! When somebody promises a "skink" they should deliver! Seriously, I'm getting ready to make upgrades in my kitchen but I'm doing granite countertops.
Carrying a worktop with a large hole in it could be problematic. Fitting and fixing the sink would make it stronger. Most cabinets for sinks do not have a top in them. Nice video.
Maar waarom zaag jij die volledige spoelbak uit je kan gewoon een gat maken voor je bak en je zaagt te veel uit
good job
He's obviously got a plunge saw yet still wants to cut the sink top out using a jigsaw 😁
lol exacly what i thought, lets just show everyone the old school way of bending there jig blade to over or undercut the top.
Probably because most people use a jigsaw ya dick head
@@TheGreg2710 😂😂😂 someones been triggered! 😂😂😂😂
1984simongraham no, just most people do not have a plunge saw and the old scool way is fine. Plunge all you like pal. 💁🏼♂️
@@TheGreg2710 serious question: what is a plunge saw? I'm used to the jigsaw as you mentioned it's old school and good for you 😁👍🏾
Is that a festool i see
Not quite installed though!
Back in my days we didn't have the luxuries of internet or UA-cam, we had to use our brains, we had to have a high level of understanding by sight and the common sense to know what problems and dangers would be expected if the job wasn't carried out correctly unlike today 2019.
2012 is when you uploaded your video but you also gave advice on how to fuck-up on a inset sink fitting which explains why through the years so many second rate jobs and DIY jobs have caused so many problems and second rate workers. Your video is not how to fit a sink but how to do the cut out for the sink, the cut out and fitting a sink are 2 different facts also, your explanation and demonstration lacks details as to fitting a sink the most basic part of the job. My advice to people like you is understand details before giving advice to the people that don't know how to do these jobs, that fact alone is in the ending of your video when you set the sink into the cut out saying done and dusted, far from was it done and dusted, maybe in future you'll mention the sink seal and the clamping of the sink.
Great so where's your video buddy? Oh your didn't make one, just came here to bitch about a guy that took time out to help others. Suggest put your energy into something positive.
your the best, xd xd
👏👏👏👍
Don’t move sink wile pencilling round it.
Well, you say that, but you've not actually installed it, as per the video title would suggest.
What about undercounter seal and clips? Protection for the cut edges in the worktop and base unit? Preparation for taps and waste trap? Taps and waste fitting?
You say it's easy, but that's probably because you've forgotten about all the additional work required to do a good job. Anything is "easy" if you ignore half the details.
You could solve this very easily. Change the video title to "How to cut worktop for sinks and appliances".
Sebastian ward how to work an insinkerator you tube
but a kitchen sink to you is not a kitchen sink to me, ok friend
15 mm of diference. genial.
unnecessery work phases.
just use a light color marker - so no masking taping
only mark the cutting line - no duble marking
Greg
Take a look at this kid who installs a counter top in a house - ua-cam.com/video/ZH6u4U0HyC0/v-deo.html
wait this aint twenty one pilots
4 cm out
Spelling errors make me giggle. Thank you
he has used the masking tape to stop the jigsaw marking the worktop....imo
That's half done...
Handy tips for DIY, can do the same job in under 5min without all that jazz.
Under 5 Mins, really?
3333tas bullshit
Should of named this junk....how to measure and cut a worktop.
WRONG!
Those lines not them lines
haha skink....
so he's doing this for ears with cheapest tools you can possibly get ?? Cheapest work top you can get and cheapest one bawl sink... Fuck me !!!
Phen0mable Can't see your point does it matter what the cost is?
foppo leeuwerke in this job is very important to have a GOOD quality tools. He claims to do it for long time but still have SHIT tools. It means that he lies or he's shit
Phen0mable how are festool and bosch cheap?! Dont think you have a clue mate!!
it's a demo video ....duh