How To Fix Dodge / Chrysler ABS , Traction and ESP BAS Fix Wheel Speed Sensor DIY
Вставка
- Опубліковано 7 чер 2018
- Hi guys! if you find this video useful you can help me by donating , it don’t matter if it’s a small amount. Anything counts , link down below Thanks ^_^
www.paypal.me/FixitFelix529
---------------------------------------------------------------------------------------------------------------
link for the OBD AL619 I used on this video
amzn.to/2FGqx0P
link for the abs sensor
amzn.to/2LOUFJq
Hi , I am showing you guys how to replace the rear driver side wheel speed sensor ,
this will fix your ABS , Traction and ESP BAS lights on in your dashboard , please be careful while being under the car ,
For business inquires email: FixitFelix529@gmail.com
How To Replace CamShaft Position Sensor on Nissan Quest
• How To Replace CamShaf...
How To Reset Ford Oil Life Easy
• How To Reset Ford Oil ...
How To Fix Air Problem on Ford
• How To Fix Air Problem...
How To Program Ford Key Fob 1997 to 2007
• How To Program Ford Ke...
How To Fix Blower Motor Resistor on a Ford or any car
• How To Fix Blower Moto...
This will show you how to replace the blower motor resistor on a Ford this method will also works on other cars with similar symptoms
the symptoms are , if the blower only works on high or if the blower works on the lower settings but not high ,
thanks for watching
How To Fix Chevrolet And GMC Air Flow Quick And Easy DIY
• How To Fix Chevrolet A...
How To Replace Door Handle on Nissan Murano 2003 - 2007 DIY
• How To Replace Door Ha...
How To Recharge Ac On A Dodge or Chrysler DIY
• How To Recharge Ac On ...
How To Fix Dodge / Chrysler ABS , Traction and ESP BAS Fix Wheel Speed Sensor DIY
• How To Fix Dodge / Chr...
How To Fix A/C on a Jetta Beetle and Passat 1.8T
• How To Fix A/C on a Je...
How To Recharge Your A/C on a Ford Focus (1999 - 2007)
• How To Recharge Your A...
How To Remove A Battery On A 2007 - 2014 Dodge Avenger DIY
• How To Remove A Batter...
How To Fix Ford P0012 Code ( VCT Solenoid replace )
• How To Fix Ford P0012 ...
How To Fix A/C on a Nissan Murano 2003 - 2007 ( Expansion Valve ) DIY
• How To Fix A/C on a Ni...
How to Replace ABS Wheel Speed Sensor On A 2006 - 2011 Honda Civic
• How to Replace ABS Whe... - Авто та транспорт
Hi guys! if you find this video useful you can help the channel grow by donating , it don’t matter if it’s a small amount. Anything counts , link down below Thanks ^_^
www.paypal.com/paypalme2/FixitFelix529
A helpul video 👌🏻
You did great 👍
Was it having trouble coming out of park
Mine is doing that right now, does it matter which one to switch or might as well do both? It turns off when I take of but only when I make a left turn it turns on again. Suggestions?
Great job with the cable. Question: were you just "out of gas" or was that a result of the broken dash fuel sensing issue? And did you fix it?
I've been driving Dodge for over a decade and I must say they are the king of sensor problems! I miss the good ol days when cars wasn't over computerized 😫
Shakarus Sanders : You aint lying, I just found this out. It’s like they all came on at the same time. 4wd, tire sensor and ESC.
@@nmtumbleweed5320 did you get yours fixed?
@@shakarussanders9911 did you?
I have been working on a buddy's Dodge Avenger for 3 weeks and I will NEVER buy a Chrysler product
To may electric ⚡ problems
The car has 142,000 miles and everything electrical is jacked up
The front end is trash " needs everything "
I was always a Chevy guy until I bought a 2008 Honda Ridgeline
Now I'm a Honda guy
I have the Ridgeline" 286,000 miles " still a great truck
I have and 2009 Honda Accord with 198,000 miles great car " if people would STOP running in to it !"
I also have a 2016 Honda Civic with 56,000 miles great car
Japanese vehicles last forever
Great job felix, especially doing it with one hand while holding that camera. Thanks, your the man.
You did a great job working on that cable in tiny space while holding the camera at the same time. 👍
I have this problem, you make it look sooooo easy to fix THANKS
Awesome video demonstrating how to replace a bad sensor! My son is replacing mine this week.
You my friend are a hero. Thank you for taking the time to make this professional video. I liked and subscribe
Thank you,my 2009 Dodge Journey SXT, has been doing this right now. I have a lifetime warranty on my truck. I will bring it,to the dealership,so they can fix it.
Magnolia Alexander I hope they fix you’re problem
Awesome. Found your video with a simple google search and this was the first one.... Subscribing because I'm getting a Magnum and those lights were on the dash as well lol.
Thank you . Those same lights came on in my 2007 Jeep Wrangler. You're the best Brother.
Hey man your video was awesome really very helpful thank you keep up the good work.
Man great video we need more videos on the magnum good job💪
Thanks man. Videos with no cutting so I can see every move you make is best. I can do this myself now
Just be careful while under the car.
If you can help me by subscribing ^_^
Yes sir. Done and done.
My brother thank you so much for the video I got that problem on my 09 rt challenger with 230k+ miles and it’s started out this year giving me problems fuel pump oil pressure sensor alternator but all in all it’s been a great car for 11 years got my money’s worth 😁
230k miles??????? What??????? Everything still good???
shuhang chen yup and for the last 2 years it’s been my plumbing truck lol and it’s still strong. Raced a charger but he got me on 3rd because the 8 speed....I got the 5 speed automatic😕
Best video for this fix!!! Thanks Felix.
Thank you Felix, great video 👌
Thx Felix. The exact lights came on on my 2015 Charger Ralley Sport and did the same to replace my ABS/Speed sensor and fixed the warning lighta.
Which one did you replace??
That was a super video! Great detail. All in under 10 minutes. Muchisimas Gracias, Francisco
Thank you so much. Your the man! Saved me so much money!!
Great vid! Thanks for the demonstration.
My ESP and BAS have been coming on and off for months but today they stayed on and I have a feeling it’s one of my wheel speed sensors. Thanks for this video, makes it look very doable for a self repair!
Did that fix it
Did those lights turn off?
There’s a recall on airbags apparently that also triggers it
Did it fix it
Always pull negative off battery and you can even remove both poos and net. And touch together for few minutes then re attach terminals appropriately . That will prevent further warning lights and in some cases unnecessary work. I have an07 charger rat 5.7 street mod pro tuned .disconnecting battery b4 and work that requires pulling any sensors out.
No point in removing both battery cables, unless you want to clean both.
Touching cables together and leaving power off may reset the current codes, however this is only clearing what the computer *knows* about any problems (including the sensor you are replacing and any other issues), it won't make any additional problems go away.
Excelente, saludos desde Sonora México, me gustó
thank you for this have been trying to figure out my issue and I believe it is exactly this
Great video. Thanks, for your help.
Thanks great video
Hey I've gotta 2012 town n country..prob started yesterday..noticed my ESC is lit on my dash and when it is on..my darn shift wont move..i have to turn to on and then i can shift to neutral to start it..I've tried pressing the button on my panel for ESC. Off ..but doesnt show its turned off..either. Any ideas?? Thanks!
Thanks Felix!
Thank you for making this!! Looking forward to seeing more videos!
Thanks dude very helpfull vid 🤗
Great video
Great information appreciate the help
Thank you! I’m gonna try this right now. Hopefully it works.
Tks Felix. My code lights are off now. You're 👌
Thanks Felix!! I just bought an 05 Magnum and had the ABS and ESP BAS lights on. I will try this and see what happen!
Put the OBD reader first to make sure that’s the problem you have
It is advisable that u scan first. One of the three issues could be responsible: ABS, speed sensor, and steering angle sensor (most especially when u tamper with steering balance during front suspension replacement without doing wheel alignment later)
@@FixitFelix529 my obd scanner won't retrieve codes related to this issue...
It’s because not all OBD readers will read ABS codes. It has to be a special OBD ready.
You can take it to a mechanic and they can check it or if you want you can purchase a OBD reader like the one I used on the video. The link is on the description
Did it work
Ótimo vídeo!
Thank you. Great video
I replaced steering angle sensor, clock spring, and abs sensors all the way around, and ABS light, BAS light, and traction light still on...do I need to have the scan tool or odb reader to clear the lights now to make them goo off...because they did not go off by themselves after replacing all these parts.
I have a Chrysler Pacifica, would mine be the same place.. was such a great understanding video bud.👍
Thank you man!!! Awesome sauce!
Thanks for you good information thanks again!!!!!!👍🏼👍🏼👍🏼👍🏼👍🏼👍🏼
Just coming in here to say I like your channel name, I approve 😂😂😂😂
Now wheres the golden hammer at?!
😂
Nice man 2 thumbs up
Thanks again
Thanks felix👍🏻😎
Good work Man
Good work ❤
hey Felix, what part of the country are you in, I am having the same problem on my 08 Charger, scanner says its left rear, same as you. But I am afraid of trying since I am in an area that gets a lot of snow and any sensors I have tried to pull of on other cars , the bolt always breaks off.
Can these sensors be tested with an ohm meter and tell if they're bad?
For those that have no scanner.
Well done I have all three lights on my 2009 Chrysler 300 will that affect my all wheel drive
Thanks, I have the same lights on my dash.... now I know what to look for. 👍
Thanks felix
Would a near dead battery set these lights off on the dash? Because my battery low light came on and not long after the ABS, traction control and esp bas came on.
Me gusto el video
Me suscribo 👍👏🏼
2013 Chrysler 300 abs and traction control lights are on? Any help?
Is there any fuse for abs sensor? Dodge nitro 2008 4x4
Ty, good video
Great Vid headed down to O'Reilly's in the morning to see if my 300 issue will be solved
Did the oriellys part work for you
@@oopoop2274 💯💯 yea it did
Got it da nx morning n put it on
Thank you 👍🏻
buena recomendacion GRACIOAS!!!!!!!
Nice!!!!
Thank you
Thank you very very much !! I just subbed!
Thanks for the sub!
It’s not always the sensors , most of the times it’s the angle steering sensor behind the air bag
Cool video nice
Do this work for 2004 dodge durango limited?
I have a 07 300c and my abs traction and esp light on but I have a 5.7 would it normally be the back one on a V8??
Que cuando se daña ese censor no se checa primero el Valero o el CV Axle?🤔
2007 Chrysler 300 ..im doing mine next....THANKS!!!
I had the esp bas light on my 06 charger I replaced wheel speed sensors then I got abs light the e brake light thing and engine light what happened?
Awesome
Mine just started doin this and actually dies sometimes on acceleration throws the esp bas and lightning bolt is this what I need to fix it I goes away but comes back intermittently
Nice
Nice vid keep up the good work and btw I sub
I changed my abs wheel sensor 2 and my light is still on what should I do
Thanks know I do have an idea how to fix it !!!!
What about a 2012Dodge caravan abs and traction sensor??
Thanks very helpful
Glad it helped
i just have the ESP BAS, and the Traction control light on, i don’t know what’s wrong with it it happened after someone hit a pole from the front
Trying to locate my camshaft on my 300 not my crankshaft the mechanic seem to keep getting them confused or maybe it's me I'm looking for the one that goes on the bottom not the top
My dodge journey is having problems with the acceleration. Can anyone help me out? I've been told it could be the map sensor or the throttle position. My car won't accelarate at all and will push back while moving
If we replace my sensor and its not that what else could it be? 06 chrysler srt8
Just changed mine but for some reason all 3 lights are still there. Any suggestions?(before a touching the sensor my guy did a diagnostic. It was a code for left side speed sensor)
I just had the same issue changed mines and it didn’t work. Did you ever find the solution?
Gracias
Hello just a question by the way great job on the video, my question we have a 2008 Nitro where the lights came on so my husband replace the front and rear sensor and the lights did not turn off, what else could it be causing the lights not to turn off? Any help is much appreciated.
You have to take it to a mechanic so he can use a computer and read the code you have. He should check it for free.
Then after he gives you the code you will know what’s wrong with it exactly
He has a code reader but no code shows up, we think maybe the fuse?
You need a special machine to read abs codes
@@FixitFelix529 got it thank you for your help,
Did a code pop up for the sensor?
So how do you know wich 1 is bad ? I have a 05 chrystler 300 with that problem the ESP BAS goes off every so often , I turn the car off n it resets
I just subscribed, did this Magnum have a grinding noise while driving? My Cherokee is an 07 and it has the same lights on but it also has a grinding noise while driving. I'm hoping the fix is this simple
Have you tried it yet? I have the same grinding noise om my voyager. Looking for a fix as well. Would really appreciate it if you could give me an update.
Antoni Lubbers I bought a code reader that does abs and it told me it was one of my speed sensors which was really easy to fix and cheap.
@@matthewhamilton1833 wow great! will try that as well! Will let you know if its fixed mine as well, thanks again.
I have the same problem,but how do I know what sensor I have to change,right or left,front or back?
Can you make another video about how to get rid of that other tell tail warning light on your dash? The yellow one that looks like a filling station pump. I’ve got that light on too. :”
Its a super easy temporary fix. You can go to the gas station and just put $10 gas. The light should go away for a while. Lol 😂
@@FixitFelix529 ha! that made my day😁
I have all3 lights on plus the brake light any suggestions?
John Shill did you find a solution?
My Charger has the same lights on right now I took it to get a reading it and it coded U0103 gear shift control module but that can’t be right.. I’m gonna go with your video.
What can of issues make the bad sensor ?
2010 Challenger R/T??
Thank the have this problem
How about the front sensors?
No, you start by going up front, in the fuse box, swap the 30A fuse for the ABS with the 30A fuse for the wipers. Start the car, and see if the light on the dash goes away. If that doesn't work, then you change the sensors
Felix, good video, but I wondering, I got a 2015 charger R/T just today when I back to start my car I notice the ABS & STABILITY CONTROL lights on saying that service need to done, just wondering if is similar sensor like the one you show.
My car has 30500 miles. And I take care so I got a dealer appointment in a week but in the mean time I just searched for ideas.
First you need to take it to a mechanic to read the codes you have. They should do it for free. They should tell you why the lights are on
@@FixitFelix529 thanks I will do that tomorrow first thing.
Felix I watch with great interest your video ref the ABS/SKID SENSOR. i own a 2014 Chrysler 300 and I am getting the skid light own. I hooked it up to one computer that told me the module is b bad and the break switch, however the brakes likes come on so I suspect the problem is with either one of the abs/skid sensor or the module itself. How can I tell if it is a sensor since I assume there are a one for each wheel, or if it is it module. any inform you could provide me would be greatly appreciated
Well if one of the wheel sensors is bad it should give you a code to which one it is.
First make sure you’re brake fluid level is normal.
If it is full then try fixing or replacing the brake switch because it’s cheaper than replacing the module.
Sometimes those lights also turn on due to a bad fuse. Try checking if you have any blown fuses
I’m having a problem with my esp/bas it’s on the dash and will not go away my car is making a knocking noise idk if it’s that or the egr valve I had a so called mechanic someone please help
Be very careful with Chrysler products! I have seen them throw ABS codes that were erroneous and misrepresented the problem. Recently I had one give me 5 codes. It said all four wheel speed sensors were bad and that it had an "under voltage" condition. We checked all the wiring and replaced the ABS module but the ABS light still did not go out. After that I decided to check the wheel speed sensors one by one. It turned out that the left front sensor was bad. Replacing it finally made the ABS light go out. The ABS codes were wrong and caused a lot of unnecessary work and expense. There is a way to unplug these high tech electronic sensors and test them while they are disconnected from the car but it requires a bit of electronics knowledge to do it. But I wouldn't do anything to a Chrysler ABS system until I check all the wheel speed sensors first. Otherwise you could get fooled. Badly.
I just changed mine all 4 the other day and the esp/bas light still on. Any help?