How To Replace Power Steering Pump 2008-2017 Buick Enclave
Вставка
- Опубліковано 2 лис 2020
- Buy Now!
New Power Steering Pump from 1AAuto.com 1aau.to/ia/1ASPP00180
Harder steering, squealing, or leaks are signs you might need to replace the power steering pump in your car or truck. This video shows you how to install a new power steering pump in your 2008-17 Buick Enclave.
• Check here for more videos on the 2008-17 Buick Enclave: • Buick Enclave 1st Gene...
This process should be similar on the following vehicles:
2008 Buick Enclave
2009 Buick Enclave
2010 Buick Enclave
2011 Buick Enclave
2012 Buick Enclave
2013 Buick Enclave
2014 Buick Enclave
2015 Buick Enclave
2016 Buick Enclave
2017 Buick Enclave
Tools you will need:
• 10mm Wrench 1aau.to/odw/1AXAA00010
• 10mm Socket 1aau.to/okf/1AXAA00017
• 15mm Socket 1aau.to/oni/1AXAA00015
• 22mm Socket 1aau.to/oaC/1AXAA00266
• Serpentine Belt Tensioner Tool 1aau.to/ox/1AXAA00019
• Trim Tool Set 1aau.to/odV/1AXXX00006
• Hose Clamp Pliers 1aau.to/oJ/1AXAA00076
• 1/2 Inch Air Impact Gun 1aau.to/oaK/1AXAA00252
• Ratchet 1aau.to/oop/1AXAA00016
• Socket Driver
• Socket Extensions 1aau.to/oni/1AXAA00015
• Swivel
• Torque Wrench 1aau.to/ohL/1AXAA00044
• Fluid Transfer Pump 1aau.to/od/1AXAA00152
• Power Steering Fluid
• Floor Jack 1aau.to/odN/1AXAA00068
• Jack Stands 1aau.to/odv/1AXAA00065
• Wheel Chocks
Subscribe: / @trq
Check out our playlist:
Buick Enclave 1st Generation 2008-17: • Buick Enclave 1st Gene...
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video. - Авто та транспорт
√ *Watch the Video*
√ *Buy The Part at 1A Auto* 1aau.to/m/Shop-TRQ-Parts
√ *Do it Yourself*
√ *Save Money*
I am deeply thankful for your video. My daughter was quoted $1800. at the Buick dealer to do this job on her ‘14 Enclave. I own a ‘12 Enclave. Many videos out there drop the engine down. I don’t have a lift and had to work on my garage floor with the car jacked up high. Without your video, I would have been lost. I followed it to the tee. The only part I varied from was that back bolt on the pump. I took it off reaching through the wheel well with a 3/8 ratchet with a short extension and a 15mm socket. Pump cost $216 with the pulley installed. Daughter’s gratitude priceless! Thanks guys!👍
+Aaron Chojnacki Thank you! We love empowering our customers and showing how to perform DIY auto repairs with our high-quality auto parts. 1aau.to/m/Shop-TRQ
Was yours a fwd or AWD?
The shop quoted me like $2k to do this. Thanks for the informative video. It's a definite life saver.
How do you stay so calm 😂 man I've worked in a few shops over the years and there would minimum ten swear words just trying to get the heat shield off
Thank you sir, I have been pondering on this job for a while because my concern was always dropping the subframe, I am a DIYer and I did not want to do that. With this video no reason to drop any subframe. I pulled out the power-steering pump as in the video, simple.
+Jeronimo Santos Thanks for watching our video! 1aau.to/m/Shop-TRQ
im glad i watched this, i almost thought about trying it lol
Thanks for the tips.doing this task this morning.
this very help full I watch this video and replace the pump 1-1/2 hrs thank for info
Just did this pump on my 2015 Traverse. My plan was to go this route of going over the exhaust with the pump rather than dropping sub frame. Ran into some frustrations, as well I purchased the new pump without the pulley and fitting, they had to be transferred from the old pump. It cuts about 30-40% of the part cost by purchasing the one without pulley and fitting. Then after removing lines, unbolting the pump… position the pump pulley slightly down and to the rear of the vehicle so that it is facing the opening between the inner fender and a-arm mount. Remove the pulley with puller (factory pulley has a groove around the hub on the outside of the pulley for a puller, you do not have to get behind the pulley at all)… both come out no problem separately through the opening above the A-arm mount. Position new pump in same spot, use install tool to install pulley… bolt it in place, attach lines. About 1/3 the time to re and re this way then going up and over the exhaust and a lot less then dropping the sub frame along with not dealing with that mess. Takes longer to remove the wheel and tie rod then the pump itself.
Best video out of all I've seen to remove/replace this pump.!
+lmagee212 Thank you! We love empowering our customers and showing how to perform DIY auto repairs with our high-quality auto parts. 1aau.to/m/Shop-TRQ
Great video. Thanks for the tips.
Now its my turn to replace the steering wheel pump on my traverse 2014.. well done!!!👌
+Javier Romero Thanks for watching our video! 1aau.to/m/Shop-TRQ
Great video thank you!!
Scott from Hibdons!
Great video. Where is the power steering fluid filter located? Going to replace my power steering pump and thinking I should replace the filter as well but don’t know where it is.
Seems like you get the tuff jobs !! Great job 👏
+Salvador Sepulveda Thanks for the feedback! 1aau.to/m/Shop-TRQ
Thanks for video very helpfull
thank very useful
Will it work for my 2010 buick lacrosse
Do think is the same for a front wheel drive
Excellent video. Working on a Traverse and could not remember how the o-ring was installed for the feed line to the pump (non-pressure). For some reason I can't install it without it leaking. At least now I know I am installing properly. I think I need to disconnect the hose as it is keeping it "cock-eyed" as I tighten the 10mm bolt. I'll remove the hose so the elbow is 100% free to line up square with the pump.
Mine is front wheel drive do u think is the same precedure?
If I’m replacing the cv axle too can it come out the side like that?
I changed my pressure hose, but now have a lot of whine noise for weeks. Level seems fine, but maybe I have air in there, I'm going to see if I can get it all out, not sure if that is the noise or the pump is now gone, any ideas?
This is by far the best video I’ve seen on this but still worried this is outside my wheel house. Having to do this on the ground instead of a hydraulic lift makes it feel like it’ll be a lot harder that in the video.
+Downhillin' Dad Thanks for watching our video! 1aau.to/m/Shop-TRQ
How'd it go? I'm debating on doing the job for a customer 🤔
Easiest way is to take off the hard line on the rack and pinion and with the pulley down pull it out between rack and motor
Is this awd or fwd
I had a friend that had her power steering pump fixed and they lost one of her bolts. Does anyone know the size of the mounting bolts on this
how did you get the pressure hose in? I've tried for a day trying to put the high press hose in.
Hello, hey I have a 2012 Chevy Traverse LT trying to put the power steering pump on and I'm having the trouble that when I drop the subframe on the passenger side it's only going down two of the four in required to pull the power steering pump. Can you think of anything I could have done wrong?
Need to drop the driver side also for more clearance
Good Video!!!
Hi Mr.TRQ I hope we can reach you I have problems same that your Buick 2010. Is leaking lots. I’m in Ontario Ca let me know thanks ❤
+Nisa Gin We wouldn't be able to diagnose an issue like that here, you may want to have a local mechanic take a look at it. Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c
CHECK RECALLS ON YOUR SUV BEFORE REPLACING
Fwd or AWD?
Hes look like a awd mine is a fwd i wonder if is the process
Car wouldn't start after replacing power steering pump
Why did I ever buy an enclave
reason number 500 i hate this car
🤣🤣🤣🤣