I've seen 9" band saw blades come off when a loose log gets pushed into them and the worst was a time when a saw found a singer sewing machine inside a large log ,which must have placed there early last century and the tree grew around it. 🙄🙄
@Mercmad finding a singer sewing machine? That's the craziest find I've ever heard of yet. That strengthens my hope to find that pot of gold in the log. Thanks for sharing and watching God bless, Shannon
Automated set works and dogs are nice but you have to pay attention. My Dad had a Frick OO mill that he rebuilt with I beams and channel iron instead of wood for the carriage, husk and track. We powered it with a D4 Caterpillar diesel engine. There were a few mishaps while sawing and I got my bells rung good when a piece of slabwood caught on the saw and hit me going about 900mph. Dad was a good man but safety and he were not in the same realm. He would do stupid things like reach by the running 56" blade to remove a piece of slabwood or go down in the sawdust pit without shutting down the diesel. He never lost any fingers and neither did I but he taught me a lot about how NOT to do things. I still work full-time as a Stationary Engineer but I am very safety conscious. I like my body parts attached and in working order!!!
You know that Frick mill is still built, and ever part is still made today. That mill has been in production from early 1900s, Thousands of Frick 00 and 01 mills still running, and still being sold by frickco.
I helped a man that had a ground mill and one of his favorite sayings was , " it don't pay much boys but it ll make a man out of ya. No idea I'd spend 33 years sawfiling for IP and West Fraser.
This is why people should treat saws with respect. Many have missed their lives, I've been lucky and only split a thumb in half at the same time I cut off 95% of one finger joint on my index finger. And that was just on a table saw, got a kickback and it sent the piece away together with the push stick and my hand in the blade. About 80-90 years ago, a relative of mine died when a saw blade exploded and cut his stomach wide open. There are extreme dangers and you should not have music on in the headphones etc, you have to listen to the sound when the saw cuts through the wood. You can hear the sound if something is wrong etc and then you can back it of or shut it down.
New sub here. I swear things happen for a reason, I was just thinkin how I missed watchin Mike's story time while cuttin...... low and behold who's sawmill pops up on my feed? Mike McCoy's!! So glad to see you've resurrected Mr. McCoy's baby. So glad I've found where it went and you've got a channel. Just now if you could incorporate "saw talk" or "story time". Much love and respect
Well, thank you, I bought the mill in 2022 with no experience what so ever. I'm slowly learning how to run this thing. As far as telling stories, I try sometimes, but I'm so boring, even my dog won't stay with me when I'm sitting on the front porch. Thanks for watching and commenting
Need to take the guys cell phone away from him so that he has his undivided attention to the saw and log. This is a great way to get yourself or someone else hurt.
John11:25 Jesus said unto her, I am the resurrection, and the life: he that believe that in me, though he were dead, yet shall he live: 26 And whosoever liveth and believeth in me shall never die. Believeth thou this?
If you knew me you would understand what I’m about to mention (and I can’t see everything): safety glasses, ear protection, steel toes, hard hat. I could watch this stuff all day. Thanks for posting!
From a sawyer here. It's not good to run the log past the saw when sawing. If the saw is running out it can grab hold of the log when you come backwards and throw it off the carriage.
slow down, make some improvements on your out feed to move the slabs away faster. You will get better and safer with time. Maybe don't try to saw logs that are so large and crooked until you are more comfortable with the machine. I could tell you were a bit nervous and unsure by the way you sawed. Again, take your time, maybe even go watch someone with a bit more experience saw a few days and have a good walk through with other mills to get some ideas. You are doing great from my point of view.
Thank you, Steve, I appreciate the advice and suggestions. I tell ya, I visited Bret and Andruw from Andruw's Lumber. He hammered my saw and spent the whole morning going over important things he wanted to be sure I was up on. After I got back and did what he wanted me to look over, that mill ran like it was a different one. There is another youtube guy called the Sawmill Pimp close by. He said I could come over anytime and check him out. I appreciate the kind comments. Thanks for watching
My brother in law has a 40” saw similar to this. One day he and a helper was sawing an 8x8 in half when the cut was half through the beam pinched the back side of the blade hard enough that it flipped the board up in the air. When it came back down, it landed directly on top of the blade which Dug in an threw the beam 50 feet out of the back of the shop where it punched a 2 foot hole and broke a 2x4 stud like it was balsa wood. No injuries but two pare of underwear were never the same.
My Lord! My first thought would be, "Did we get that on film?" Thanks for sharing that. That's a scary and awesome tale. Thanks for watching and commenting
The only saws that don't kick back are hand powered. Kickbacks can happen while running anything from bandsaws to concrete cutters and then some. Let's not forget safety, safety, and safety. When we have remembered to be safe, let's not forget safety, safety, and safety!!!
With that much tension in those logs is the lumber not going to be any good? You can work with a bend or bow in lumber an inch or less but more that that you're just asking for trouble.
Thanks, Tom. I record it all and just don't care about the ugly comments. If a man sticks his neck out in this hateful world, someone is going to try and cut his head off. But the way I look at it is the more they say the more it helps the video get viewers. Good luck with the mill and thanks for watching and commenting
Both my grandpaws had saw mills when I was growing up got to work a bunch around them they were Frick mills 58" blades, dangerous work but alsome lumber..stay safe guy's, great video..
I was born at my grandfather's sawmill in Finland. This was on the lake where logs were floated to the mill. Fortunately, I was not allowed anywhere close to the work areas while I was a toddler. There are lots of fond memories from those early years. 😊😊
Been around sawmills, log yards, logging for sixty years. The stuff is dangerous. No amount of safety devices will stop all accidents. Fact is, all that stuff may contribute to things going sideways. You try to work as safe as you can but know stuff is going to happen. Cruising in the redwoods years ago. Eating lunch one day when about a hundred feet away, the entire top of a tree fell to the ground. Fifteen minutes later, and someone on the crew would have had a bad day.
Thanks for the awesome story. I had an Uncle who was in the Forestry Service in the Redwoods of California back in the 70's. Thanks for watching and commenting
Used a RadialArm Saw, shapers planners. used to keep a long thumb nail! I'd get tired of dado's & get sloppy, saw blade would ding my thumb nail & I'd shut her down & take a break! Seen panel saws take fingers off, shaper knuckles & chunks of fingers when a knot blew up when fellow was turning radius cuts
As a fellow sawyer myself…not trying to tell you what to do, but your lead on your saw is off a bit, and your feeding rate is to fast. Slow down a bit, and also sharpen your dogs. Good luck!
When I’m sawing and the dogs slip off try not to panic hit the E-stop and don’t move the carriage until sawblade stops turning We have a vertical edger so when that happens it hits the edger and shoots back 50 feet
It was disconnected when I bought the mill, and I really just haven't given it any thought. I think it would only take a short chain to put back in service. Trying to remember I think Mrs. McCoy told me she didn't like it and took that chain off. I think I remember her telling me that? Thanks for asking
Right on !!!! The first was operator not paying attention that the slab went sideways and he pulled it back into the blade...launch time !!! And the last 2not paying attention if the dogs were down and holding....pay attention !!!
It's awesome how much power is there. I was hit in my fat belly from kick back on a 10" table saw. That hurt and was a little scary. Just can't imagine what happened there.
Same here on a 12" table saw a offcut came back at me so hard it would have impaled me if it hadn't hit my thick belt, the skin behind the belt and pants was torn and bloody bruise. One of a few close ones. Recently cut my knee open when I let a throttled off chainsaw in my left hand still spinning but thought it was about stopped but it caught my pants and that made it bite into my flesh, blood running down to soak my sock in seconds. Was fairly lucky healed up really well. First time in 35 years I cut myself with a running chainsaw. Man they cut skin like nothing else I wouldn't want to have a throttle on accident with one. Was using a old saw I don't use very often and not used to it, but it was the riggers gloves I was wearing out of the blue also, and when I held saw in one hand to bend down to move a log the saw handle rolled in my hand making bar drop onto knee. Point is be extra careful when using something different or in a different fashion to usual.
@@templehillsawmill1748 I'm sorry to see the damage caused by that log. I was surprised to see the blade wobble and wondered what damage may have been done.I run a 10" Lucas Mill in Australian Hardwood all on my own so I'm not pushed faster than I want to go by having to keep my off-sider busy and his wage worth the cut timber etc so I have time to take extra care, if blade catches bad enough the blade stops via some clutch. I note blade evenness and sharpness are important factors and wedging the cut on certain relief cuts. Only happened once in over 10 years using them, usually if the cut closes up the blade keeps spinning and engine labors hard and you can hold the carriage from running away while you quickly close the throttle and then wedge the cut if the log hasn't moved keep cutting from there. I would love a carriage mill like yours but they are very dangerous from what I see, productivity is awesome with two guys but no amount of extra productivity is worth a serious injury. Accidents must be avoided at every cost, there's too many bad stories in saw milling. May Father Bless you and your mill.
Please find and down load the book,[ circular sawmills and there efficient operation ] published by the USDA. Circular sawmills used to be a common community college course in many states. Read the book understand it. There is a lot of information on these mills, The board splitter that caused this wreck, has been illegal in some states for years, the only splitter more dangerous is the small wheel type, That i have seen in some you tube videos. You need the splitter that is half moon shaped, running about 1/2 to 1 inch behind the blade. Throwing boards back has killed plenty of sawyers. Also read and understand OSHA requirements for circular saw mills. Your sawmill could be made OSHA approved real easy at little cost. Guy i worked for in NC taught saw milling at the local community college in the 70s and 80s. The mill i worked at in NC sawed about 3 hr ever day, Then ever one went home while i sorted stacked and loaded lumber and scaled and unloaded logs and cleaned and sharpened mill and made sure it was in top shape. The mills main propose was to demonstrate how to run a mill, to the college students. Just looking at these mills scare the hell out of some people.
I am telling you now way I would work on that mill I see at least 50 safety issues that need to be addressed you are going to get someone seriously injured or killed that has to be one of the most happy Hazzard mill I ever seen
@@templehillsawmill1748 well i was not trying to be a smart ellick but that is a lot of people get killed in a saw mill that delevery bely or what ever you call is all but usless like it is it needs to level with rollers
@@templehillsawmill1748 Been running saw mills sense i was 12 year old,yes 12 year old i was sawing on a 01 frick, your board splitter is a piece of crap, it will get you killed, find a better one and mount it proper. Also take even amount of wood off both sides of heart, it will take the tension off the log even. Watch feed rate,dont over load blade capacity. I have run mills for over 50 years, i could run that mill so fast, the guy off bearing would walk off the job. With just a few changes that mill would run 10,000 ft of lumber per day with 4 man crew. With just 2 guys, 2000 ft is a days work. Problem with circular mills is the man power needed to get production. But production is very high. With 2 men operating cost is to high because of low production. Just adding a edger and 1 edger man and 1 off bearer , production goes up 30 per cent.
The height of the cant was too tall for the lower dog, and the top dogs just touched it but with not enough bite. And with the log tension squeezing the blade, it just slid right off. I need to work on it for sure. Thanks for watching and commenting
Take that a lesson learned. When logs have allot of tension in them only cut 1" material out of it. Less likely to pinch the blade and cause that problem.
Take that a lesson learned. When logs have allot of tension in them only cut 1" material out of it. Less likely to pinch the blade and cause that problem.
My question is why do you let the carriage travel past the saw and the splitter your gonna get hurt or your off bearer,thats how stuff gets between the splitter and the saw . Not trying to be smart but I worked on a mill just like this
Well, Doug, I really didn't realize I am doing that. But, I will work on not doing it because I can see what you're saying, and it sounds good. Let me ask you about the carriage pump unit. I'm not getting but 300 lbs of pressure, and I have spoken to that D&D Sawmill Services and was told it should have 1,500 lbs. He was supposed to get a price for me but hasn't. The carriage is really slow to respond in either direction. Sometimes it won't finish cutting and I have to back up and take off again. Does your saw have 1,500 lbs? Or would you even worry about it? It will saw but not as responsive as I feel it should be. Thanks for asking about that. I really didn't know that I shouldn't.
@@templehillsawmill1748 I don't know about the pressure,our carriage and set works look just like (sold out in 2005) but was powered by electric . Do your belts slip when it won't finish the cut?
@dougsmith9099 No, sir, belts don't slip. Saw doesn't slow down. The carriage will just slow down and act like it just runs out of horse power. But, that only happens from time to time. The biggest problem is trying to stop the carriage before it hits the stop if it returns too fast. Or when it's time for it to return, it takes forever for it to start moving. I feel like the fella at D&D Services is right, saying the pump needs rebuilt or replaced. I appreciate your interest and sharing some knowledge.
@@templehillsawmill1748 are they telling you that it's in the valve body for your carriage control lever? I don't ever remember if we rebuilt that or not,is there a filter on the hydraulics
@dougsmith9099 they are saying the pump itself should have 1,500 lbs. The valve is OK, and it does have a filter that I replaced a few weeks ago, along with draining all the fluid and replacing with new.
I see that the "" Saw"" drops the cut off the same way all / most of the time!!! Nooo , I don't know why!!! Is the { saw and mount } not parrellel the carriage ??? Mark Garr???? his does not do this. So looks like the set up is incorrect.
Maybe some coaching from Mark would be in order here, both operational and set up. The kinetic energy in that sawblade is nothing to take lightly. Thankfully you lived to saw another day.
The blade is protected by shear pins in the mandrel. Takes lot more than a little board to damage blade, How ever over feeding and jamming blade will lock it up and shear pins. Hitting steel in a log and not reaction fast enough will wreck a blade and could kill you, that carriage should reverse in just a flash of your eye. A good sawyer always is alert for metal in the log and ready to reverse A sawyer should never take his mind off that carriage and blade and never under any circumstance get between log and saw when flipping or loading logs. If off bearer is a distraction they must be replaced before they get hurt or get you hurt.
Tks God No got hurt 😔, remember at the sawmill got to THINK 🤔 SAFETY and always put SAFETY FIRST . I see spruce lumber 🪵 crab the saw blade and go flying threw the air at highway speed . Get a D6 CAT DEISEL turn up 🔝 on cutting 33’ feet logs 🪵 watch its if spruce . Fir , pine , cedar and any hardwood is all right . 8’ 6” foot 🦶 logs is a long time getting board feet 🦶 out in a day . We call it wait off good time on a sawmill.😊
that's the 1ST time 😮😮 I seen that be 4 / 1 the board fell off right 👉 😮 at the carriage wheel 2 the rest of the log looks like it wasn't dogged down that's not good either 3 and when running trims U use a edger most Sawyers don't fool W that it takes a long time U are looking at lumber production in a day's time so U can a tractor trailer of lumber 4 the week 😊😊 OMG 6 3O 2O24
I’ve sawed many many logs and there’s absolutely no need to run the carriage more than an inch or two past the saw once you’ve through the log . Why are you feeding it so far past the cutting teeth ?
I didn't know, but several have said the same thing. I've sawed since this video and have stopped as you are suggesting to me to do. I appreciate you asking, and thanks for watching
@@templehillsawmill1748 You learn how, you dont need to cut ever board all the way off, you can leave 1/2 of wood holding make next cut on 1 inch i drop 3 boards at once, so off bearer only makes one trip for 3 boards.
WOW! No safety gear at all. No gloves/ eyeglasses / hard hat, etc. Someone is gonna loose a limb or even die!! Plus the saw rig looks unsafe, rust everywhere, out dated. What more needs to be said!! I have been sawing logs for over 25 years, and safety is first, second keep your machine in good working condition and have good safety minded help. This is a death trap!!
You know nothing about sawmill for sure,and you kinda sound like some jerk that works osha Grew up logging& have worked on at least 30 sawmills in my day. I'm 67 now,still got all my fingers and toes. If you can't stay alive and uninjured in one of the most dangerous occupations there is,then GET OUT! If you're scared,just say your scared!😂😂😂😂
Not much of a bad accidents but the potential for really bad accidents doing this must be high a lot of moving parts. At least this guy keeps a good distance from the cutting blade. I don't think I would like to try this. Looks like it can be very dangerous.
Same thing as tension on a tree, reason tree falls the direction you leave wood holding, much tension as that log had, it was most likely wind shocked. Reason you remove equal amounts of wood from around heart wood, if not your lumber will dry out like rocking chair rockers, wind shock timber will twist as it drys.
I dont know what more beat; the teeth on that blade of that poor undersized Detroit diesel. Goodness, aint you guys ever heard of Restore? You would see a noticeable improvement buy lunchtime or at least after five hours........
Just sayin, sir. It's your profit margin. Restore does not F around. It has proprietary crap in it that fills in scores and scratch marks in the bores. It also says right on the can not recommended for any engine under 50K miles. A body making a claim like that tends to grab folks attention. Your Detroit is a perfect candidate. Just be sure to grab a larger can of the 3 sizes
@doctorcountersteer6580 appreciate your concern. I'm just not that worried about it. But, seriously, please come back and watch the channel. I really do appreciate you watching and commenting
@@templehillsawmill1748 I am so glad that nobody got hurt. I like sawmills. It is so cool to see a what is inside a log. Sometimes there is gold and sometimes it is just to late. I am not sure why I like Mark so much. I sent him some of my metal art and I think you bought my bottle bass for the fund raiser. Good to see you!!!!
I wouldn't call it a bad day, both of you there left with no blood loss or broken bones. If you decked the open space between the blade and cab as far back as you can without impeding your log loading, I believe it would help a lot. Also, I would raise the outfeed belt some and increase its FPM. Your Offbearer wouldn't have to work as hard. Make sure your log dogs are sharp enough to firmly hold the log against the knee. In fact the whole carriage looks like it could benefit from a little TLC.
You maybe right, I'm not going to say I have it set up really good. But, I did just check the lead last week and it's within a 1/16". Thanks for suggesting that and I'll certainly check on that again this week.
@@templehillsawmill1748 Not downing you one bit. I learn every day I'm by far a professional 4 and a half years now and still consider myself rookie. Good job on the thousand Subs 👍😎
Inattention, lack of maintenance, lack of guarding, not addressing a known problem only an idiot would be anywhere near this machine when it was operating.
Looks no different to the head rigs I worked on 40 years ago. Where,may I ask would you put guards? Everything appears to working exactly as intended so where is the lack of maintenance? Old style milling like this is hard dangerous work and fools are never tolerated so the safety aspect is addressed from the moment the saw is started.
Done two years in a lot better sawmill than this arrangement and there was more than enough accidents there you will end up with someone dead or worse if you don't sort this out
Awh! But there's always room for improvement. I'm always striving to grow and do a better job than I was able to in the past. Please keep an eye on my channel and see if I do. Thanks for watching and commenting
@@templehillsawmill1748 One thing i noticed, never get in direct line with the blade in case the blade slings a tooth out, i have seen teeth bury up in a 8x8 post when they came out. The tooth will come in direct line behind blade on sawyer side.
I think you are quite careless. To me you have created your owne accidents. You are also very disrespectful to your offbearer! You start retracting the sled while his hands are in harms way! I wouldn't want to be near machinery you are operating. Also you need to slow down the feed and alow your helper to clear the cut material. Those were totally avoidable!
Chuck, I appreciate your observation and commenting on my poor operating skills. I certainly want to improve my sawing. I couldn't agree more that the accidents were 100% avoidable, but accidents do happen regardless, and I wanted to share this video showing what had happened. As for the safety of my off bearer; I will forever remember what you have said here today and will pay more attention to where he is at all times. I do appreciate the candid comments, and thank you for watching.
@templehillsawmill1748 Your response is very commendable!! Many people would take criticism poorly! Believe me, I don't intend to bash anyone. I just don't want to see anyone hurt! Equipment although expensive, can be repaired or replaced. Lives and limbs can't. It seems your dogs aren't biting very well or don't have enough pressure??? Putting that freshly cut piece of lumber on top actually made things worse. You lost any bite the dogs would have had. Fix things up and cut some more lumber. Thanks again for the gracious response. Many uncaring people would have negatively responded. You are a true gentleman!
@@templehillsawmill1748 I do believe the "off bearer" could have sharpened his work rate without compromising himself, with that body language he would never work with me. just sayin'
@@gala1ish using his mobile phone is dangerously slack of the off guy. seems to have little regard for his own safety, or is blindly unaware of the dangers ?? hope his health insurance is up to date !!
@@templehillsawmill1748 Do not slow down your feed, it dont work that way,feed must match blade rpm, or you will make dust not chips and wear off back side of your teeth. If off bearer is to slow replace him, that carriage needs to come back as soon as cut ends.
Not going like you planned 🧐 when incidents happen people like to call them accidents not thinking it was preventable, in your situation it was totally preventable, that first cut you could’ve stopped and waited for the board to be taken away so it didn’t get caught on the carriage, on the second incident you saw it was starting to bind and reversed, then on the third incident that was totally unnecessary, because you should’ve put the cant in the firewood pile. Hope you figure out how to prevent “incidents” because having an “accident” in your pants won’t feel good.
I can't argue with anything you said there. I agree it was totally preventable, and I do appreciate you pointing that out. I'm just getting started, but wanting to improve myself. Thanks for watching and commenting
Board getting into saw is the last day for a off bearer. Hell my wife can do a better job than that, i can saw twice as fast and she would never let a board get into the saw, but that could not happen on my mill,because the board splitter would prevent it. But off bearer can pick board up contact blade and kill sawyer, I got one mill i bought cheap because a board did kill the owner.
Why are you using such old equipment???? That equipment should be in a scrap yard. I have read a lot of the comments and one thing is obvious: you are extremely lucky. I hope you get new equipment before one of you gets hurt. And from the comments you are running a very hazardous operation.
Sam, thank you for your concern about our safety. I can't argue that sawmilling can be dangerous, so please keep praying for our safety. The equipment really isn't that old. As far as I know, it was manufactured in 1972. That is younger than I am, and I hope I'm not considered to be old. Thanks for watching and commenting
@@templehillsawmill1748 I have seen other guys running sawmills like yours and like yours they are having accidents. Nobody has been killed or injured,yet.
New equipment does not translate to safer operation. The lumber industry as a whole is one of the most dangerous occupations there is according to oasha.
@@timeversman9804 If you know how dangerous the industry is, why do you tell people to f**k off, when they point out your hazardous operation. I can only conclude that you are a stubborn old man who makes life miserable for your family because of your hard-headed attitude. Or you just don't care if you or your employees get injured. About 1/4 of your comments are people telling you how unsafe you are. All you do is say thanks for pointing that out and then continue doing the same thing.
At over 100 thousand dollars dont think he will saw enough to pay for it, but newer mills are nice, only one man operation it, the carriage moving at many times that speed, log turning and dog down so fast you barley see it, one down the road, can saw logs as fast as you can unload them off the truck.
Never said I did. If I'm granted enough time down here, I should be as good as anyone is. I'm learning each time I fire up the ole mill. Thanks for watching and commenting, Faron.
I've seen 9" band saw blades come off when a loose log gets pushed into them and the worst was a time when a saw found a singer sewing machine inside a large log ,which must have placed there early last century and the tree grew around it. 🙄🙄
@Mercmad finding a singer sewing machine? That's the craziest find I've ever heard of yet. That strengthens my hope to find that pot of gold in the log. Thanks for sharing and watching
God bless, Shannon
Automated set works and dogs are nice but you have to pay attention. My Dad had a Frick OO mill that he rebuilt with I beams and channel iron instead of wood for the carriage, husk and track. We powered it with a D4 Caterpillar diesel engine. There were a few mishaps while sawing and I got my bells rung good when a piece of slabwood caught on the saw and hit me going about 900mph. Dad was a good man but safety and he were not in the same realm. He would do stupid things like reach by the running 56" blade to remove a piece of slabwood or go down in the sawdust pit without shutting down the diesel. He never lost any fingers and neither did I but he taught me a lot about how NOT to do things.
I still work full-time as a Stationary Engineer but I am very safety conscious. I like my body parts attached and in working order!!!
I miss working with my dad as well. He would love to work on this ole mill. I appreciate your insight and memories, thanks for watching and commenting
You know that Frick mill is still built, and ever part is still made today. That mill has been in production from early 1900s, Thousands of Frick 00 and 01 mills still running, and still being sold by frickco.
@cliffclark6441 oh yeah that sounds good
Im running a 1940s 50" double side for bigger logs, im also trained on a semi auto scragg(gravy shift)
Oh yeah
I helped a man that had a ground mill and one of his favorite sayings was , " it don't pay much boys but it ll make a man out of ya. No idea I'd spend 33 years sawfiling for IP and West Fraser.
Yeah, one day I went to work as usual and celebrated 35 yrs. It flies by. Thanks for watching and commenting
This is why people should treat saws with respect. Many have missed their lives, I've been lucky and only split a thumb in half at the same time I cut off 95% of one finger joint on my index finger. And that was just on a table saw, got a kickback and it sent the piece away together with the push stick and my hand in the blade. About 80-90 years ago, a relative of mine died when a saw blade exploded and cut his stomach wide open. There are extreme dangers and you should not have music on in the headphones etc, you have to listen to the sound when the saw cuts through the wood. You can hear the sound if something is wrong etc and then you can back it of or shut it down.
Sorry about your fingers, appreciate you sharing. Thanks for watching and commenting
Bet that bought your eyes together.
@stevo68 yeah I bet so
This. You have to know your saw and the log youre cutting 100%
No time for not doing that@@jeffkelly3102
New sub here. I swear things happen for a reason, I was just thinkin how I missed watchin Mike's story time while cuttin...... low and behold who's sawmill pops up on my feed? Mike McCoy's!! So glad to see you've resurrected Mr. McCoy's baby. So glad I've found where it went and you've got a channel. Just now if you could incorporate "saw talk" or "story time". Much love and respect
Well, thank you, I bought the mill in 2022 with no experience what so ever. I'm slowly learning how to run this thing. As far as telling stories, I try sometimes, but I'm so boring, even my dog won't stay with me when I'm sitting on the front porch. Thanks for watching and commenting
Need to take the guys cell phone away from him so that he has his undivided attention to the saw and log. This is a great way to get yourself or someone else hurt.
@MacDa-yy8xn Yes, sir, cell phones are the worst invention ever. I have one, too, but I really do hate em. Thanks for watching and commenting
Life is a death trap and nobody's gonna get out alive
John11:25 Jesus said unto her, I am the resurrection, and the life: he that believe that in me, though he were dead, yet shall he live:
26 And whosoever liveth and believeth in me shall never die. Believeth thou this?
If you knew me you would understand what I’m about to mention (and I can’t see everything): safety glasses, ear protection, steel toes, hard hat. I could watch this stuff all day. Thanks for posting!
I appreciate it. Thanks for watching and commenting
From a sawyer here. It's not good to run the log past the saw when sawing. If the saw is running out it can grab hold of the log when you come backwards and throw it off the carriage.
That's what someone else said to. I appreciate you sharing. I didn't know that. Thanks for watching and commenting
slow down, make some improvements on your out feed to move the slabs away faster. You will get better and safer with time. Maybe don't try to saw logs that are so large and crooked until you are more comfortable with the machine. I could tell you were a bit nervous and unsure by the way you sawed. Again, take your time, maybe even go watch someone with a bit more experience saw a few days and have a good walk through with other mills to get some ideas. You are doing great from my point of view.
Thank you, Steve, I appreciate the advice and suggestions. I tell ya, I visited Bret and Andruw from Andruw's Lumber. He hammered my saw and spent the whole morning going over important things he wanted to be sure I was up on. After I got back and did what he wanted me to look over, that mill ran like it was a different one. There is another youtube guy called the Sawmill Pimp close by. He said I could come over anytime and check him out. I appreciate the kind comments. Thanks for watching
Mark sent me here....that last log would have been firewood after the 1st mishap
That ole Mark has been really good to me. He's a good fella. Thanks for watching and commenting
My brother in law has a 40” saw similar to this. One day he and a helper was sawing an 8x8 in half when the cut was half through the beam pinched the back side of the blade hard enough that it flipped the board up in the air. When it came back down, it landed directly on top of the blade which Dug in an threw the beam 50 feet out of the back of the shop where it punched a 2 foot hole and broke a 2x4 stud like it was balsa wood.
No injuries but two pare of underwear were never the same.
My Lord! My first thought would be, "Did we get that on film?" Thanks for sharing that. That's a scary and awesome tale. Thanks for watching and commenting
That’s called “kick back”. It can happen on a table saw without a riving knife or with a misapplied push stick. It is VERY PAINFUL, Ask me how I know.
OK. So his skull went thru the 2 foot hole first ?
@@RichardKuivila1947 it was close
The only saws that don't kick back are hand powered. Kickbacks can happen while running anything from bandsaws to concrete cutters and then some. Let's not forget safety, safety, and safety. When we have remembered to be safe, let's not forget safety, safety, and safety!!!
With that much tension in those logs is the lumber not going to be any good? You can work with a bend or bow in lumber an inch or less but more that that you're just asking for trouble.
Some of 4X4's have bowed but most of it turned out nice
I like that you are sharing the good with the bad, I'm working on setting up a sawmill myself.
*New Subscriber* 🤠
Thanks, Tom. I record it all and just don't care about the ugly comments. If a man sticks his neck out in this hateful world, someone is going to try and cut his head off. But the way I look at it is the more they say the more it helps the video get viewers. Good luck with the mill and thanks for watching and commenting
Some of that final destination stuff
Lol
Both my grandpaws had saw mills when I was growing up got to work a bunch around them they were Frick mills 58" blades, dangerous work but alsome lumber..stay safe guy's, great video..
Both sides of the family, wow! Thank you for watching and commenting
I was born at my grandfather's sawmill in Finland. This was on the lake where logs were floated to the mill. Fortunately, I was not allowed anywhere close to the work areas while I was a toddler. There are lots of fond memories from those early years. 😊😊
@@joeahopelto8032 I appreciate you sharing the fond memories. Thanks for watching and commenting
Been around sawmills, log yards, logging for sixty years. The stuff is dangerous. No amount of safety devices will stop all accidents. Fact is, all that stuff may contribute to things going sideways. You try to work as safe as you can but know stuff is going to happen. Cruising in the redwoods years ago. Eating lunch one day when about a hundred feet away, the entire top of a tree fell to the ground. Fifteen minutes later, and someone on the crew would have had a bad day.
Thanks for the awesome story. I had an Uncle who was in the Forestry Service in the Redwoods of California back in the 70's. Thanks for watching and commenting
I do like the sound of that Detroit. Music to my ears
A unique sound for sure
Glad you're okay. Thanks for the video.
I appreciate it. Thanks for watching and commenting
Used a RadialArm Saw, shapers planners. used to keep a long thumb nail! I'd get tired of dado's & get sloppy, saw blade would ding my thumb nail & I'd shut her down & take a break! Seen panel saws take fingers off, shaper knuckles & chunks of fingers when a knot blew up when fellow was turning radius cuts
Thanks for watching
Bad day at Temple Hill Sawmill for sure. Glad everyone is ok.
I appreciate it. Thanks for watching and commenting
Table saw will throw the board back at your right shoulder if you ain't giving holding pressure on it.
Yes, sir, really fast too. Thanks for watching and commenting
As a fellow sawyer myself…not trying to tell you what to do, but your lead on your saw is off a bit, and your feeding rate is to fast. Slow down a bit, and also sharpen your dogs. Good luck!
That's alright, Sam. I appreciate the useful tips. Thanks for watching and commenting
Nobody got hurt nothing broke down just live and learn !!
That's right, I'm learning every time I saw. Thanks for watching and commenting
First and foremost no one got hurt. Did the dogs not operate properly on that second log, or did it just bind up on the blade?
It squeezed it tight. Thanks for watching and commenting
When I’m sawing and the dogs slip off try not to panic hit the E-stop and don’t move the carriage until sawblade stops turning We have a vertical edger so when that happens it hits the edger and shoots back 50 feet
I appreciate it. Thanks for watching and commenting
Got to get them doggies in.. Lesson learned,your doing fine, this is how we learn.. glad no one was hurt..
Thanks for watching and commenting
The powered roller off the off-bearer belt is not powered.. why is that?
It was disconnected when I bought the mill, and I really just haven't given it any thought. I think it would only take a short chain to put back in service. Trying to remember I think Mrs. McCoy told me she didn't like it and took that chain off. I think I remember her telling me that? Thanks for asking
Dog's not catching,not paying attention and speed is what everyone would tell me that caused that Xs 3, if I had done it!
I appreciate the feedback. Thanks for watching and commenting
@@templehillsawmill1748 it wasnt doged
Right on !!!! The first was operator not paying attention that the slab went sideways and he pulled it back into the blade...launch time !!! And the last 2not paying attention if the dogs were down and holding....pay attention !!!
@wilburfinnigan2142 yep, I can't argue with that. Thanks for watching and commenting
@@templehillsawmill1748 BE CAREFUL !!! Those old mills are dangerous and they will eat you alive !!!
hi there some days are like that , no one got hurt , it was a lesson , best to all john
Thanks for watching
Yes. It's only a lesson if you actually learn from it.
those logs with tension should be firewood.
Yeah, a lot of the logs I get should be firewood. Thanks for watching and commenting
It's awesome how much power is there. I was hit in my fat belly from kick back on a 10" table saw. That hurt and was a little scary. Just can't imagine what happened there.
That would hurt for sure right on the soft underbelly. Thanks for the memories
Had one kick back on a 10" missed me splintered the wall..new respect..
Same here on a 12" table saw a offcut came back at me so hard it would have impaled me if it hadn't hit my thick belt, the skin behind the belt and pants was torn and bloody bruise. One of a few close ones. Recently cut my knee open when I let a throttled off chainsaw in my left hand still spinning but thought it was about stopped but it caught my pants and that made it bite into my flesh, blood running down to soak my sock in seconds. Was fairly lucky healed up really well. First time in 35 years I cut myself with a running chainsaw. Man they cut skin like nothing else I wouldn't want to have a throttle on accident with one. Was using a old saw I don't use very often and not used to it, but it was the riggers gloves I was wearing out of the blue also, and when I held saw in one hand to bend down to move a log the saw handle rolled in my hand making bar drop onto knee. Point is be extra careful when using something different or in a different fashion to usual.
@livingadamman7994 good advice. Thanks for sharing
@@templehillsawmill1748 I'm sorry to see the damage caused by that log. I was surprised to see the blade wobble and wondered what damage may have been done.I run a 10" Lucas Mill in Australian Hardwood all on my own so I'm not pushed faster than I want to go by having to keep my off-sider busy and his wage worth the cut timber etc so I have time to take extra care, if blade catches bad enough the blade stops via some clutch. I note blade evenness and sharpness are important factors and wedging the cut on certain relief cuts. Only happened once in over 10 years using them, usually if the cut closes up the blade keeps spinning and engine labors hard and you can hold the carriage from running away while you quickly close the throttle and then wedge the cut if the log hasn't moved keep cutting from there. I would love a carriage mill like yours but they are very dangerous from what I see, productivity is awesome with two guys but no amount of extra productivity is worth a serious injury. Accidents must be avoided at every cost, there's too many bad stories in saw milling. May Father Bless you and your mill.
Please find and down load the book,[ circular sawmills and there efficient operation ] published by the USDA. Circular sawmills used to be a common community college course in many states. Read the book understand it. There is a lot of information on these mills, The board splitter that caused this wreck, has been illegal in some states for years, the only splitter more dangerous is the small wheel type, That i have seen in some you tube videos. You need the splitter that is half moon shaped, running about 1/2 to 1 inch behind the blade. Throwing boards back has killed plenty of sawyers. Also read and understand OSHA requirements for circular saw mills. Your sawmill could be made OSHA approved real easy at little cost. Guy i worked for in NC taught saw milling at the local community college in the 70s and 80s. The mill i worked at in NC sawed about 3 hr ever day, Then ever one went home while i sorted stacked and loaded lumber and scaled and unloaded logs and cleaned and sharpened mill and made sure it was in top shape. The mills main propose was to demonstrate how to run a mill, to the college students. Just looking at these mills scare the hell out of some people.
Will do
Reason that square piece log wood come off because there wasn't any down pressure foot locks on square log wood machine not set up properly 😢
I worked on improving the dogs and have gotten acceptable results. Thanks for watching and commenting
Why don't they debark and make cants before making lumber??
Don't own a debarker
I am telling you now way I would work on that mill I see at least 50 safety issues that need to be addressed you are going to get someone seriously injured or killed that has to be one of the most happy Hazzard mill I ever seen
We strive to improve each time we get together and saw. I appreciate you sharing your concerns and thanks for watching
@@templehillsawmill1748 well i was not trying to be a smart ellick but that is a lot of people get killed in a saw mill that delevery bely or what ever you call is all but usless like it is it needs to level with rollers
@@templehillsawmill1748 Been running saw mills sense i was 12 year old,yes 12 year old i was sawing on a 01 frick, your board splitter is a piece of crap, it will get you killed, find a better one and mount it proper. Also take even amount of wood off both sides of heart, it will take the tension off the log even. Watch feed rate,dont over load blade capacity. I have run mills for over 50 years, i could run that mill so fast, the guy off bearing would walk off the job. With just a few changes that mill would run 10,000 ft of lumber per day with 4 man crew. With just 2 guys, 2000 ft is a days work. Problem with circular mills is the man power needed to get production. But production is very high. With 2 men operating cost is to high because of low production. Just adding a edger and 1 edger man and 1 off bearer , production goes up 30 per cent.
Glad nobody got hurt. Jack up them roller feeds about 1/2" and when any cant jams up on the blade, back it out and buck it for firewood.
Yeah, a lot of my logs I get should be firewood. Thanks for watching and commenting
If they work hard enough they just might break even!
I have doubts, lol
Are the dogs not working?, thanks for sharing.
The height of the cant was too tall for the lower dog, and the top dogs just touched it but with not enough bite. And with the log tension squeezing the blade, it just slid right off. I need to work on it for sure. Thanks for watching and commenting
I thought the same thing. The dogs ain't catching.
I thought the cant weighed enough but that tension pinched the blade causing it to slide back. Thanks for watching and commenting
Take that a lesson learned. When logs have allot of tension in them only cut 1" material out of it. Less likely to pinch the blade and cause that problem.
Take that a lesson learned. When logs have allot of tension in them only cut 1" material out of it. Less likely to pinch the blade and cause that problem.
That log had more tension than I have ever seen I might of flipped it on its side or just gave up better safe than sorry
Lol! I appreciate it
looks like the dogs weren't set in agressively enough
I think you're right. Thanks for watching and commenting
Wood's getting very expensive .... you'll make some $$$ there. Be safe! Awesome video thanks!
Yes, sir, I'm slowly making enough to pay for the cost of operating. Thanks for watching and commenting
My question is why do you let the carriage travel past the saw and the splitter your gonna get hurt or your off bearer,thats how stuff gets between the splitter and the saw . Not trying to be smart but I worked on a mill just like this
Well, Doug, I really didn't realize I am doing that. But, I will work on not doing it because I can see what you're saying, and it sounds good. Let me ask you about the carriage pump unit. I'm not getting but 300 lbs of pressure, and I have spoken to that D&D Sawmill Services and was told it should have 1,500 lbs. He was supposed to get a price for me but hasn't. The carriage is really slow to respond in either direction. Sometimes it won't finish cutting and I have to back up and take off again. Does your saw have 1,500 lbs? Or would you even worry about it? It will saw but not as responsive as I feel it should be. Thanks for asking about that. I really didn't know that I shouldn't.
@@templehillsawmill1748 I don't know about the pressure,our carriage and set works look just like (sold out in 2005) but was powered by electric . Do your belts slip when it won't finish the cut?
@dougsmith9099 No, sir, belts don't slip. Saw doesn't slow down. The carriage will just slow down and act like it just runs out of horse power. But, that only happens from time to time. The biggest problem is trying to stop the carriage before it hits the stop if it returns too fast. Or when it's time for it to return, it takes forever for it to start moving. I feel like the fella at D&D Services is right, saying the pump needs rebuilt or replaced. I appreciate your interest and sharing some knowledge.
@@templehillsawmill1748 are they telling you that it's in the valve body for your carriage control lever? I don't ever remember if we rebuilt that or not,is there a filter on the hydraulics
@dougsmith9099 they are saying the pump itself should have 1,500 lbs. The valve is OK, and it does have a filter that I replaced a few weeks ago, along with draining all the fluid and replacing with new.
Your belt feed seems to be set too low compared to the first roller?
Yeah, we thought about raising it up some. Sometimes, it takes a while to get things done. Thanks for watching and commenting
rough day for sure,
It sure enough was. Thanks for watching and commenting
I see that the "" Saw"" drops the cut off the same way all / most of the time!!!
Nooo , I don't know why!!!
Is the { saw and mount } not parrellel the carriage ???
Mark Garr???? his does not do this. So looks like the set up is incorrect.
It's all good now
Congrats on 1,000 subs bud
I appreciate it, Andruw.
Maybe some coaching from Mark would be in order here, both operational and set up. The kinetic energy in that sawblade is nothing to take lightly. Thankfully you lived to saw another day.
That's some good advice, thanks.
The blade is protected by shear pins in the mandrel. Takes lot more than a little board to damage blade, How ever over feeding and jamming blade will lock it up and shear pins. Hitting steel in a log and not reaction fast enough will wreck a blade and could kill you, that carriage should reverse in just a flash of your eye. A good sawyer always is alert for metal in the log and ready to reverse A sawyer should never take his mind off that carriage and blade and never under any circumstance get between log and saw when flipping or loading logs. If off bearer is a distraction they must be replaced before they get hurt or get you hurt.
That is fire wood if I ever saw a stick .
Yes, sir, and I know that now myself too. Thanks for watching and commenting
@@templehillsawmill1748 We usually learn the hard way .
Tks God No got hurt 😔, remember at the sawmill got to THINK 🤔 SAFETY and always put SAFETY FIRST . I see spruce lumber 🪵 crab the saw blade and go flying threw the air at highway speed . Get a D6 CAT DEISEL turn up 🔝 on cutting 33’ feet logs 🪵 watch its if spruce . Fir , pine , cedar and any hardwood is all right . 8’ 6” foot 🦶 logs is a long time getting board feet 🦶 out in a day . We call it wait off good time on a sawmill.😊
@@leonardryan8723 33ft! That's getting out there!
that's the 1ST time 😮😮 I seen that be 4 / 1 the board fell off right 👉 😮 at the carriage wheel 2 the rest of the log looks like it wasn't dogged down that's not good either 3 and when running trims U use a edger most Sawyers don't fool W that it takes a long time U are looking at lumber production in a day's time so U can a tractor trailer of lumber 4 the week 😊😊 OMG 6 3O 2O24
I appreciate the feedback and thanks for watching and commenting
fix that with a bit of steel plate, would also fix the overhang problem
I appreciate it. Thanks for watching and commenting
I’ve sawed many many logs and there’s absolutely no need to run the carriage more than an inch or two past the saw once you’ve through the log . Why are you feeding it so far past the cutting teeth ?
I didn't know, but several have said the same thing. I've sawed since this video and have stopped as you are suggesting to me to do. I appreciate you asking, and thanks for watching
@@templehillsawmill1748 You learn how, you dont need to cut ever board all the way off, you can leave 1/2 of wood holding make next cut on 1 inch i drop 3 boards at once, so off bearer only makes one trip for 3 boards.
I appreciate you sharing all this. Really do.
Thank God no one was hurt!
fully God is good. Thanks for watching and commenting
Oh how nice it would be to be young you have a strong back
A strong young man for sure. Thanks for watching and commenting
It was a rough day no doubt but I'm just glad that nobody got hurt!
Yes, sir, we all want to go home as well as when we showed up. Thanks for watching and commenting
Looks like a little maintenance wouldn't hurt.
Good observation, Harold. I do need to work on the dogs. Thanks for watching and commenting
I didn't realize that was the McCoy mill!
It is. I bought from the family early in 2022. Thanks for watching and commenting
That outbfeed is gonna hurt someone if yuns dont McGiuver it or something
That's okay. Help ain't hard to find.
Cool video. Stay safe out there
I appreciate it, Chris. Thanks for watching and commenting
Things happen fast at the sawmill
And I was trying to make things happen faster than I should have. Thanks for watching and commenting
Be careful and thank you for waiting till the end of the video to "like it"
I appreciate it, Dave. Thank you for the compliment
That mill looks extremely antique.
Hey, Alan, great observation, thanks for watching and commenting
It is not a old mill, the same mill is still made today, this mill dont even resemble a old hand set mill.
WOW! No safety gear at all. No gloves/ eyeglasses / hard hat, etc. Someone is gonna loose a limb or even die!! Plus the saw rig looks unsafe, rust everywhere, out dated. What more needs to be said!! I have been sawing logs for over 25 years, and safety is first, second keep your machine in good working condition and have good safety minded help. This is a death trap!!
Thanks for watching and commenting
You know nothing about sawmill for sure,and you kinda sound like some jerk that works osha
Grew up logging& have worked on at least 30 sawmills in my day. I'm 67 now,still got all my fingers and toes. If you can't stay alive and uninjured in one of the most dangerous occupations there is,then GET OUT!
If you're scared,just say your scared!😂😂😂😂
And don’t forget to check your phone
@@LarrySinclair-m6v ok
Sangat menakjubkan ,salam satu profesi
Thank you.
1st one was a joke ,done watching 😮
Well, I'd like to ask you to give my channel another chance.
Not much of a bad accidents but the potential for really bad accidents doing this must be high a lot of moving parts. At least this guy keeps a good distance from the cutting blade. I don't think I would like to try this. Looks like it can be very dangerous.
Thanks for watching and commenting
Im a sawyer in Canada, its not for everyone.
Yeah, you can always get a job at the coffee house
@@templehillsawmill1748 I love my job. It keeps me mentally sharp.
What’s log tension?
Well, it's the log squeezing the blade as it's been cut. It shouldn't squeeze the blade at all. But this log did
@@templehillsawmill1748 10-4. Thank you.
Same thing as tension on a tree, reason tree falls the direction you leave wood holding, much tension as that log had, it was most likely wind shocked. Reason you remove equal amounts of wood from around heart wood, if not your lumber will dry out like rocking chair rockers, wind shock timber will twist as it drys.
I sure appreciate you commenting. Thanks for watching
I dont know what more beat; the teeth on that blade of that poor undersized Detroit diesel. Goodness, aint you guys ever heard of Restore? You would see a noticeable improvement buy lunchtime or at least after five hours........
We don't start till after lunch doc. Thanks for watching and commenting
Just sayin, sir. It's your profit margin. Restore does not F around. It has proprietary crap in it that fills in scores and scratch marks in the bores. It also says right on the can not recommended for any engine under 50K miles. A body making a claim like that tends to grab folks attention. Your Detroit is a perfect candidate. Just be sure to grab a larger can of the 3 sizes
@doctorcountersteer6580 appreciate your concern. I'm just not that worried about it. But, seriously, please come back and watch the channel. I really do appreciate you watching and commenting
Sent here by Mark and that log was bad news. (firewood) 🤕
I'll know next time, Bigdawg! That ole Mark is a good one. Glad you came over.
Working with weathered rusted uncovered junk is going to get someone hurt.
Thanks for watching and commenting
Is that a detroit i here
671 Billybob
Some logs make better firewood then lumber.
Yes they do. Seems like I get all the worst ones.
Mark G. told me to check your video out.
Oh yeah? Well, what do you think? Ole Mark is a good ole fella. I really like him
@@templehillsawmill1748 I am so glad that nobody got hurt. I like sawmills. It is so cool to see a what is inside a log. Sometimes there is gold and sometimes it is just to late. I am not sure why I like Mark so much. I sent him some of my metal art and I think you bought my bottle bass for the fund raiser. Good to see you!!!!
I wouldn't call it a bad day, both of you there left with no blood loss or broken bones. If you decked the open space between the blade and cab as far back as you can without impeding your log loading, I believe it would help a lot. Also, I would raise the outfeed belt some and increase its FPM. Your Offbearer wouldn't have to work as hard. Make sure your log dogs are sharp enough to firmly hold the log against the knee. In fact the whole carriage looks like it could benefit from a little TLC.
Steve, thank you for the feedback. Those are good suggestions. I appreciate you watching and commenting
@@templehillsawmill1748 Nothing quite like the care and feeding of a sawmill. Keep up the good work!
Wow, some days make you wish you just stayed in bed. Glad no one hurt!
Sure enough! At the end of the day we still had a nice stack of pretty lumber. Thanks for watching and commenting
Don't think you're blade is square with carriage, where the tension is coming from
Pine logs have tension in them other species too especially when they are fresh cut
You maybe right, I'm not going to say I have it set up really good. But, I did just check the lead last week and it's within a 1/16". Thanks for suggesting that and I'll certainly check on that again this week.
@marcchatterson-xq7qt these logs had just been cut two days prior. I appreciate your comments
@@templehillsawmill1748 figured maybe the first accident could have gotten it out of line. I got a mill of my own, edminston fully hydraulic
@@williamgardner8105 oh yeah, I see what you're saying. I'll definitely be sure to check that. Thank you for commenting
Were you racing somebody , good thing nobody got hurt. My suggestion just like everybody else slow down. 👍
Thanks for watching
@@templehillsawmill1748 Not downing you one bit. I learn every day I'm by far a professional 4 and a half years now and still consider myself rookie. Good job on the thousand Subs 👍😎
Oh yeah, I appreciate it Gary
wow
Yeah, sure enough. Thank you for watching and commenting
Inattention, lack of maintenance, lack of guarding, not addressing a known problem only an idiot would be anywhere near this machine when it was operating.
You're probably right about all that. Thanks for watching and commenting
Looks no different to the head rigs I worked on 40 years ago. Where,may I ask would you put guards? Everything appears to working exactly as intended so where is the lack of maintenance? Old style milling like this is hard dangerous work and fools are never tolerated so the safety aspect is addressed from the moment the saw is started.
@mercmad, if I still drank, I'd like to buy you a beer. I appreciate your thoughtful comment. God bless ya.
@@Mercmad You are right, at least 6 running around here cutting cross ties, his is up town. Most are handset with no cab,
This mill is poorly maintained. Everything it rusted.
Yeah, I don't never do anything to it. Why would you
OHSA stop 🛑 work immediately
Thanks for watching
Done two years in a lot better sawmill than this arrangement and there was more than enough accidents there you will end up with someone dead or worse if you don't sort this out
Well, let's pray that doesn't happen
I didn't see one dangerous accident. I saw machine failure due to operator error / poorly maintained equipment.
Thanks for commenting
Why is anyone surprised? That whole rig is a death trap. Not a question of if, only when.
Awh! But there's always room for improvement. I'm always striving to grow and do a better job than I was able to in the past. Please keep an eye on my channel and see if I do. Thanks for watching and commenting
Hell there is half dozen around here sawing rail road ties ever day, much worse than his setup.
@@templehillsawmill1748 One thing i noticed, never get in direct line with the blade in case the blade slings a tooth out, i have seen teeth bury up in a 8x8 post when they came out. The tooth will come in direct line behind blade on sawyer side.
I think you are quite careless. To me you have created your owne accidents. You are also very disrespectful to your offbearer! You start retracting the sled while his hands are in harms way! I wouldn't want to be near machinery you are operating.
Also you need to slow down the feed and alow your helper to clear the cut material. Those were totally avoidable!
Chuck, I appreciate your observation and commenting on my poor operating skills. I certainly want to improve my sawing. I couldn't agree more that the accidents were 100% avoidable, but accidents do happen regardless, and I wanted to share this video showing what had happened. As for the safety of my off bearer; I will forever remember what you have said here today and will pay more attention to where he is at all times. I do appreciate the candid comments, and thank you for watching.
@templehillsawmill1748 Your response is very commendable!! Many people would take criticism poorly! Believe me, I don't intend to bash anyone. I just don't want to see anyone hurt! Equipment although expensive, can be repaired or replaced. Lives and limbs can't.
It seems your dogs aren't biting very well or don't have enough pressure??? Putting that freshly cut piece of lumber on top actually made things worse. You lost any bite the dogs would have had. Fix things up and cut some more lumber. Thanks again for the gracious response. Many uncaring people would have negatively responded. You are a true gentleman!
@@templehillsawmill1748 I do believe the "off bearer" could have sharpened his work rate without compromising himself, with that body language he would never work with me. just sayin'
@@gala1ish using his mobile phone is dangerously slack of the off guy. seems to have little regard for his own safety, or is blindly unaware of the dangers ?? hope his health insurance is up to date !!
@@templehillsawmill1748 Do not slow down your feed, it dont work that way,feed must match blade rpm, or you will make dust not chips and wear off back side of your teeth. If off bearer is to slow replace him, that carriage needs to come back as soon as cut ends.
Not going like you planned 🧐 when incidents happen people like to call them accidents not thinking it was preventable, in your situation it was totally preventable, that first cut you could’ve stopped and waited for the board to be taken away so it didn’t get caught on the carriage, on the second incident you saw it was starting to bind and reversed, then on the third incident that was totally unnecessary, because you should’ve put the cant in the firewood pile. Hope you figure out how to prevent “incidents” because having an “accident” in your pants won’t feel good.
I can't argue with anything you said there. I agree it was totally preventable, and I do appreciate you pointing that out. I'm just getting started, but wanting to improve myself. Thanks for watching and commenting
Board getting into saw is the last day for a off bearer. Hell my wife can do a better job than that, i can saw twice as fast and she would never let a board get into the saw, but that could not happen on my mill,because the board splitter would prevent it. But off bearer can pick board up contact blade and kill sawyer, I got one mill i bought cheap because a board did kill the owner.
@@cliffclark6441 oh
Why are you using such old equipment???? That equipment should be in a scrap yard. I have read a lot of the comments and one thing is obvious: you are extremely lucky. I hope you get new equipment before one of you gets hurt. And from the comments you are running a very hazardous operation.
Sam, thank you for your concern about our safety. I can't argue that sawmilling can be dangerous, so please keep praying for our safety. The equipment really isn't that old. As far as I know, it was manufactured in 1972. That is younger than I am, and I hope I'm not considered to be old. Thanks for watching and commenting
@@templehillsawmill1748 I have seen other guys running sawmills like yours and like yours they are having accidents. Nobody has been killed or injured,yet.
New equipment does not translate to safer operation. The lumber industry as a whole is one of the most dangerous occupations there is according to oasha.
@@timeversman9804 If you know how dangerous the industry is, why do you tell people to f**k off, when they point out your hazardous operation. I can only conclude that you are a stubborn old man who makes life miserable for your family because of your hard-headed attitude. Or you just don't care if you or your employees get injured. About 1/4 of your comments are people telling you how unsafe you are. All you do is say thanks for pointing that out and then continue doing the same thing.
At over 100 thousand dollars dont think he will saw enough to pay for it, but newer mills are nice, only one man operation it, the carriage moving at many times that speed, log turning and dog down so fast you barley see it, one down the road, can saw logs as fast as you can unload them off the truck.
Your teeth are dull and you pick up to much speed in the cut. Your teeth are not squared up
I appreciate the feedback, Bill. Can't disagree with you. I have been trying to improve on my sharping skills. Thanks for watching and commenting
You guys don't know what your doing
Never said I did. If I'm granted enough time down here, I should be as good as anyone is. I'm learning each time I fire up the ole mill. Thanks for watching and commenting, Faron.
Glad you're okay. Thanks for the video.
I appreciate it. Thanks for watching and commenting