I got my .410 kit the other day and thank you for that. I will say that it has a little bit of a learning curve to get used to. The reprime stem did not hold up, but no worries. I can say how much I appreciate the fact that you spent some time to develop this kit and how well it does work.
I got the .410 Lee Loadall kit today. Haven't gotten a chance to use it yet but I will update after I do. Thanks a lot Below The Tideline. I was surprised how fast it got to me in the states the way shipping has been lately.
In step one it looks like you are aligning a hole in the top of the de-prime tool to the load-all de-prime pin. My de-prime tool does not have a hole in the top so the tool with hull will not fit under the load-all to allow de-priming.
it hard to give any load data because there are so many different powders that can be used, i dont know what powder the individual will be using so i stay away from trying to give load data
I just got your kit and have watched the video a few times…starting to sink in. Also, I am having difficulty locating the Mec 410 resizer. Can you help? Thanks
Where abouts are you?.. in the UK you can get them from Clay Game or Reloading UK, in the US Ballistic products or direct from MEC and there are loads of suppliers in Ebay wher you can buy one from
it will work on the 20 gauge one as well, the tops of all the punches are flat so it does not matter what gauge of loadall you use they are all able to push down on of the tools
In the instruction video you have an orange adapter for the powder/shot, but this is not available in your kit or site ??? This is absolutely critical IMO. Will you make this available for clients that have purchased your kit ? Cheers!
The adaptor works ok but i prefer you use my lee perfect powder measure for the powder as it can handle fine powders like H110 better than the loadall a version of the adaptor might come up in the future though
Sorry that happened, i guarantee all the items i make so i will send out i replacement punch right away there will be no cost to you, i am looking at putting a steel core down the middle of the punch so this wont happen again.
@@3Dreloading Thank you so much. I'm thinking about putting a metal washer on the top with super glue. When the top broke the stem cocked way over to one side, I think that was what broke the bottom end.
@@glennvadney3103 I wont be putting the steel core in the depriming rod, i have changed the infill in the depriming rod to 100% this makes it much stronger and will fix the issue
@@raysherrod9322 I think it would work out too expensive to try and sell it takes over 20 hours to print and uses a lot of filiment it would probably workout at $35 to $40 so i think that is too much.I could try and skinny it down to make it cheaper but it would not be as strong, i do have something else coming up along the same sort of lines that will be cheaper i will post a video of it soon
Thanks for asking about the tools i sell them on ebay under the name 3dreloadingandmore they are both instock at the moment here is a link to the 410 tools, if youtube will allow it: www.ebay.com/itm/204556939902
There could be a few things that are causing that. if you are using once fired cases make sure you have the previous fold lined up with the wire in the crimp starter so it folds in the same place also you only need to put a small amount of pre-crimp on the case and then use the other crimp die to close over the folds before you use the punch to finish the crimp. If you are using new cases again you only need a small amount of pre-crimp before putting in the crimp finish and closing down with the punch, if you look at the video you can see the crimp being nearly closed before being closed with the punch this is at the 3min and 20 second mark on the video
Just ordered one from you on eBay. Watching the video though, I noticed what looks like a adapter for the shot/powder drop tube? Is that needed and do you sell it?
I have not put the adaptor up for sale yet, it would only really work if you had bushes suitable for 410 loads, i have bushes suitable for 1/2 oz of shot and 14 gr of powder, but sometimes it is just as quick using the Lee powder dispenser for the powder and a scoop for the shot
@@3Dreloading Gotcha, I have the extra 3D printed powder and shot bushings for lighter loads also, but I usually use my powder measure or Lee powder dippers.
At the end of the video there are the prices and contact details to order one of the kits .Posted to the UK £14 posted to the USA $22 email me at aberisle@gmail.com
@3Dreloading I tried 5 3" cheddite hulls, and they look horrible. Did exactly what the video showed. I even tried doing it slowly and the same results. I just ordered a mec reloader it won't do me wrong. I'm not saying the product is bad it doesn't work for me
I got my .410 kit the other day and thank you for that. I will say that it has a little bit of a learning curve to get used to. The reprime stem did not hold up, but no worries. I can say how much I appreciate the fact that you spent some time to develop this kit and how well it does work.
Just ordered the kit. I've been reloading .410 by hand with a roll crimp for years and it takes forever. Looking forward to this kit.
Sick man. what an awesome 410 conversion kit
I got the .410 Lee Loadall kit today. Haven't gotten a chance to use it yet but I will update after I do. Thanks a lot Below The Tideline. I was surprised how fast it got to me in the states the way shipping has been lately.
Thanks i keep them in stock and ship straight away.
In step one it looks like you are aligning a hole in the top of the de-prime tool to the load-all de-prime pin. My de-prime tool does not have a hole in the top so the tool with hull will not fit under the load-all to allow de-priming.
I have upgraded the repriming pin if you watch this video you see the upgrade, ua-cam.com/video/IATcmvbmbAg/v-deo.html
Got it - Thanks for the quick response...
Awesome, where can I purchase this kit?
You can get it from me at aberisle@gmail.com let me know where you are so i can get a price with shipping
i don't see the kit in the shop. could you publish the proper link....interested in anything for the 410...thanks
where do you find your load data for 410 that are compatible with these bushings?
it hard to give any load data because there are so many different powders that can be used, i dont know what powder the individual will be using so i stay away from trying to give load data
I am trying to find where to order this 410 loading tools. I am electronically challenged and cant navigate to the correct place. HELP PLEASE !!!!
I have them on Ebay here is a link to them www.ebay.co.uk/itm/205017026421
I just got your kit and have watched the video a few times…starting to sink in. Also, I am having difficulty locating the Mec 410 resizer. Can you help? Thanks
Where abouts are you?.. in the UK you can get them from Clay Game or Reloading UK, in the US Ballistic products or direct from MEC and there are loads of suppliers in Ebay wher you can buy one from
Interested in purchasing the necessary tools for loading 410 with the Lee load all. Im struggling to find it, tho. Where can i go to order?
if you look on ebay for 3d printed loading tools for the lee loadall in 410 you will see them
Will this work with a 12ga. or 20ga. Lee Loadall ?
it is made to fit the 12gauge loadall
@@3Dreloading Thanks 🙏
what load all does this work with? i've been debating on buying the 20ga one
it will work on the 20 gauge one as well, the tops of all the punches are flat so it does not matter what gauge of loadall you use they are all able to push down on of the tools
In the instruction video you have an orange adapter for the powder/shot, but this is not available in your kit or site ??? This is absolutely critical IMO. Will you make this available for clients that have purchased your kit ?
Cheers!
The adaptor works ok but i prefer you use my lee perfect powder measure for the powder as it can handle fine powders like H110 better than the loadall a version of the adaptor might come up in the future though
Are you using a 2 3/4 inch lee load all? And loading 2 1/2 .410 shells? Or some other combination? Thank you
yes it is a standard lee load all and you can load 410 shells from 3 inch down to 2" shells
Just ordered the kit can u post the resizer link please
Could you make one for 24 gauge? I like to fold crimp mine but this looks a little easier and may work better.
Its unlikely i would need to get 24 gauge cases to get all the measurements and they are not a common size
Can you send me another repriming tool, the one in the kit broke the top and bottom off on the third reload shell. Let me Know how much plus shipping.
Sorry that happened, i guarantee all the items i make so i will send out i replacement punch right away there will be no cost to you, i am looking at putting a steel core down the middle of the punch so this wont happen again.
@@3Dreloading Thank you so much. I'm thinking about putting a metal washer on the top with super glue. When the top broke the stem cocked way over to one side, I think that was what broke the bottom end.
Have you modified this re-prime tool with the steel core yet ? I'd like to order this kit but I want to wait until you fix this issue. Thanks !
@@glennvadney3103 I wont be putting the steel core in the depriming rod, i have changed the infill in the depriming rod to 100% this makes it much stronger and will fix the issue
The little stand under your Lee Load-all did you make it?
Yes i did it holds3 packs of primers and the 2 drawers hold bushes and odds and ends
@@3Dreloading Do you make any to sell?
@@raysherrod9322 I think it would work out too expensive to try and sell it takes over 20 hours to print and uses a lot of filiment it would probably workout at $35 to $40 so i think that is too much.I could try and skinny it down to make it cheaper but it would not be as strong, i do have something else coming up along the same sort of lines that will be cheaper i will post a video of it soon
Still for sale? Didn't see this in your ebay store
yes they are still for sale i will be putting more on ebay today
I would like to buy the 410 an 28 gauge lee loadall adapter
Thanks for asking about the tools i sell them on ebay under the name 3dreloadingandmore they are both instock at the moment here is a link to the 410 tools, if youtube will allow it: www.ebay.com/itm/204556939902
Having some issues with the pre-crimp. I get uneven folds, splits, or worst case half crimp/half squished. Any tips with it?
There could be a few things that are causing that. if you are using once fired cases make sure you have the previous fold lined up with the wire in the crimp starter so it folds in the same place also you only need to put a small amount of pre-crimp on the case and then use the other crimp die to close over the folds before you use the punch to finish the crimp.
If you are using new cases again you only need a small amount of pre-crimp before putting in the crimp finish and closing down with the punch, if you look at the video you can see the crimp being nearly closed before being closed with the punch this is at the 3min and 20 second mark on the video
Anyone have a link to purchase?
I have them on ebay just look under the name 3dreloadingandmore or 410 lee loadall loading kit or you could contact me direct on aberisle@gmail.com
Just ordered one from you on eBay. Watching the video though, I noticed what looks like a adapter for the shot/powder drop tube? Is that needed and do you sell it?
I have not put the adaptor up for sale yet, it would only really work if you had bushes suitable for 410 loads, i have bushes suitable for 1/2 oz of shot and 14 gr of powder, but sometimes it is just as quick using the Lee powder dispenser for the powder and a scoop for the shot
@@3Dreloading Gotcha, I have the extra 3D printed powder and shot bushings for lighter loads also, but I usually use my powder measure or Lee powder dippers.
Could i get one of your kits to the UK Thanks
They are made in the UK if you email me at aberisle@gmail.com, i will give you a price including post. thanks...james
Hello belowthetideline my reprinting tool broke at the top could please send me another one
email me your address and i will get a replacement sent out to you you can get me at aberisle@gmail.com
Very hard to crimp closed when using new Fiocchi shells.
I use Fiocchi hulls the ones i use are skived so the neck of the shell is a bit thinner it makes easier to put a crimp on it
Kool kit. Would be awesome if there was audio.
I need the info to order a kit.
At the end of the video there are the prices and contact details to order one of the kits .Posted to the UK £14 posted to the USA $22 email me at aberisle@gmail.com
Is this a silent video
Yes thats why there is text at each stage
Very clever.
Dosen't work on new hulls very disappointing.
I bought a mec problem solved.
While it is eaisier to crimp once fired hulls i have used new Fiocchi hulls and managed to crimp them and they turn out good.
@3Dreloading I tried 5 3" cheddite hulls, and they look horrible.
Did exactly what the video showed.
I even tried doing it slowly and the same results.
I just ordered a mec reloader it won't do me wrong. I'm not saying the product is bad it doesn't work for me
What’s your eBay name? I Want to make sure I get the right you😂
Here is my ebay name: abis4466