Відео

It says in the video description that there is no resizing shown. If you want to see resizing look at the 410 video

I do have thumb screws, i do a version that has screws with a 3d printed head on it that can be screwed in or unscrewed with your fingers they are just not on that video

that would be a nice idea but the spring or gas ram would get in the way of it tilting back, the bottles are quite quick and easy to remove to change powder or shot with the conversion.

it hard to give any load data because there are so many different powders that can be used, i dont know what powder the individual will be using so i stay away from trying to give load data

I have them on Ebay here is a link to them www.ebay.co.uk/itm/205017026421

I have upgraded the repriming pin if you watch this video you see the upgrade, ua-cam.com/video/IATcmvbmbAg/v-deo.html

Got it - Thanks for the quick response...

I make them in 10,12,16 and 20 gauge they are available in mt ebay shop at www.ebay.co.uk/itm/204942690529

can you explain what you mean by a triangle, it should just look like a cone shape with the folds of the precrimp.

While it is eaisier to crimp once fired hulls i have used new Fiocchi hulls and managed to crimp them and they turn out good.

@3Dreloading I tried 5 3" cheddite hulls, and they look horrible. Did exactly what the video showed. I even tried doing it slowly and the same results. I just ordered a mec reloader it won't do me wrong. I'm not saying the product is bad it doesn't work for me

I make the conversion and have them on sale in ebay, just ype in "lee loadall bottle conversion" and you should find it.

Making shot

@@3Dreloading goatee than you

i have them along with other reloading tools on ebay here is a link to them: www.ebay.co.uk/itm/204617725570

there is a plug you fit in the bottle and lift up to decant the powder, you can see it better when i do it with the shot bottle

@@3Dreloading ok thank you

i would like to but youtube dont like the showing of load data , companies like Hogden and Alliant all have free load data on thier sites you can get it there

I have them on ebay here is a link to them www.ebay.co.uk/itm/204617725570

it is made to fit the 12gauge loadall

@@3Dreloading Thanks 🙏

i have them on ebay here is a link to them www.ebay.co.uk/itm/204617725570

if you look on ebay for 3d printed loading tools for the lee loadall in 410 you will see them

yes they are still for sale i will be putting more on ebay today

you can get them on ebay here is a link to them www.ebay.co.uk/itm/204654126253

you can get them on ebay here is a link to them www.ebay.co.uk/itm/204636529164

thanks i got your payment the stand is being posted out today,

Great !

I got the stand and shock not the steel conversion tho !? Is it still coming ? Also can I buy a 2nd stand

you can get them direct from MEC or from Ballistic products

Yes i just put some on ebay today www.ebay.co.uk/itm/204621647851

thanks for asking about the trimmers, i sell a range of them on ebay under the name "3dreloadingandmore", i do a mini version for cutting down shotshells to make mini shells it will cut shells down to 1,5" in length. here is my email address aberisle@gmail.com

yes the screw at the large end holds the blade in place and ther other screw it to adjust the the mount you need trimmed from the hull

yes there is a taper on the end of the trimmer, i sell them on my ebay shop "3dreloadingandmore"

its Maxam SSB150 a shotshell powder

Where abouts are you?.. in the UK you can get them from Clay Game or Reloading UK, in the US Ballistic products or direct from MEC and there are loads of suppliers in Ebay wher you can buy one from

what weight of steel are you trying to load and what kind of problems are you getting?

@@3Dreloading I've noticed a couple problems. It seems like the shot is jamming up and when I crimp new hulls the crimp looks great. Then after a few minutes it starts to undo. I'm using an ounce and a half.

if the shot is jamming in the drop tube just keep a screwdiver handy and give the droptube a couple of taps when dropping the shot and this should free the shot to drop properly, if the shells are opening up after crimping you could have too much shot in try reducing the load down by removing a few bits of shot and see if that helps or get a dime and put that ontop of the crimped shall and try doing the finish crimp again and this should push the crimp a bit deeper. i think it is most likly to bee too much shot though.

@@3Dreloading I'll give it a try. Thanks

they are Fiocchi hulls i got them from Folkstone enginering in the the UK

@@3Dreloading cheers man

Yes they are for sale the price is $32 that includes postage, you can get them from me on ebay just look for 410 loading tools for the lee loadall and you will see them or try my ebay ID "3Dreloadingandmore"

@@3DreloadingI just checked eBay and you don’t have any 410 kits for the Lee load all available. Will you be making any more?

@@bryanroseberry6990 i have just put a new batch on ebay today

i have just put a new batch on ebay today@@bryanroseberry6990

Thanks for asking about the tools i sell them on ebay under the name 3dreloadingandmore they are both instock at the moment here is a link to the 410 tools, if youtube will allow it: www.ebay.com/itm/204556939902

Thanks for asking about the tools, i sell them on ebay just search for "410 loading tools for the lee loadall" and you will see them, they are instock and ready to ship in a day....thanks...james

I sell them on my ebay shop here is a link to them www.ebay.co.uk/itm/204479401116 or just look on ebay for "3dreloadingand more" and you will find them there