How To Install a DVD Player In Your Vehicle -EricTheCarGuy
Вставка
- Опубліковано 12 лют 2015
- CarID was kind enough to send me a DVD player from Boss to install into my 2001 Honda Odyssey. Originally, I had thought it would be a pretty straightforward installation. It turned out to be a bit more than that. The headliner had to come out several times to make sure that the right measurements were made for the mounting bracket. The mounting bracket also needed a custom installation in order to make it work. Not to mention getting 'creative' with the electrical hook ups. Truth is, this is typical with installing aftermarket accessories like this. You need to be prepared for anything.
In this video I walk you though the steps I took to overcome these challenges. Hopefully it will help you if you are also wanting to install a DVD player of this type.
Thanks again to CarID. Here's a link to their site: www.carid.com
Here's a link to the DVD player I installed: www.carid.com/boss-audio/12-1-...
Premium Members of EricTheCarGuy.com have an extended version of this video available: www.ericthecarguy.com/premium-...
Camera Brian Kast
Thanks for watching.
The best place for answers to your automotive questions: www.ericthecarguy.com
Tools
Cordless Drill: www.jbtoolsales.com/buffalo-to...
Dewalt 3/8" Impact: www.jbtoolsales.com/dewalt-dc8...
Butane Soldering Kit: www.jbtoolsales.com/solder-it-...
Wire Stripper: www.jbtoolsales.com/sg-tool-ai...
Crimping Pliers: www.jbtoolsales.com/sk-hand-to...
Stepped Drill Bit: www.jbtoolsales.com/titan-tool...
Automatic Punch: www.jbtoolsales.com/lisle-3028...
Power Probe 2: www.jbtoolsales.com/power-prob...
Add-a-Circuit: www.jbtoolsales.com/bussman-bp...
Electrical Tape: www.jbtoolsales.com/3m-06133-s...
Related Videos
Sylvania Lighting Install: • Sylvania ZEVO LED Kit ...
Element Fog Lights (Part 1): • 2004 Honda Element HID...
Element Fog Lights (Part 2): • 2004 Honda Element HID...
Discussion about this video: www.ericthecarguy.com/kunena/1...
Useful articles.
Engine overheat
www.ericthecarguy.com/faq/what...
No start problems
www.ericthecarguy.com/faq/solv...
Idle issues
www.ericthecarguy.com/faq/solv...
Performance issues
www.ericthecarguy.com/faq/solv...
Diagnosing Noises
www.ericthecarguy.com/faq/diag...
Diagnosing Vibrations
www.ericthecarguy.com/faq/dete...
Electrical Problems
www.ericthecarguy.com/faq/solv...
Brake Issues
www.ericthecarguy.com/faq/solv...
Transmission issues
www.ericthecarguy.com/faq/solv...
HVAC problems
www.ericthecarguy.com/faq/solv...
Leaks
www.ericthecarguy.com/faq/find...
MPG
ericthecarguy.com/faq/finding-...
Social Network Links
Facebook: EricTheCarGu...
Twitter: / ericthecarguy
Google+: plus.google.com/1001951801966...
Instagram: / ericthecarguy
Stay Dirty
ETCG
Due to factors beyond the control of EricTheCarGuy, it cannot guarantee against unauthorized modifications of this information, or improper use of this information. EricTheCarGuy assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. EricTheCarGuy recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video. Due to factors beyond the control of EricTheCarGuy, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not EricTheCarGuy. - Авто та транспорт
Grab some popcorn and we'll watch a movie. ua-cam.com/video/5RWkh99190M/v-deo.html
Hey Eric, l've a 2007 Odyssey EX-L with DVD in it and how to replace the Odyssey original DVD to this big one?
Smashing job eric :-), there is more than one way to get the holes in the right place, but yours worked smashing :-))
The things you do to make a quality video Eric. I hate those things but appreciate your drive to show us how. Keep it up!(fairmont video hype!!)
Elmano Locko 1 - Remove old DVD2 - Follow this video.
i heard if you spin the drill bit in reverse it will cut stuff like carpet and that padding
Cheers to that guy that says he installs them every day without removing headliner. Wicked good quality.
Im glad you showed using that 'tap a fuse'. Im planning on using them when I add heated seats to my truck. Thanks!!
I'm always waiting for new vids from EricTheCarGuy .
Just saw the installation video and wow it's hard work but thanks for the education video Eric.....thumbs up.
Awesome. Nothing goes like the instructions say. I'm looking into replacing the factory "RES" rear entertainment system with an aftermarket. I'm 99% sure, after watching this, my kid can just play on the phone.
People say he should have just gotten a ipad and use that but did you think about how safe it would be to leave in the car ? thats right no unless you take it out and in everytime this is the next best thing its mounted on so they would have to do all this work just to remove it and run off with it i think this is better since it adds a more factory look to the car
When I was installing factory DVD players, we had to cut a hole in the headliner and mount the plate. Also, why not pull the radio and make your power connections?
hey Eric . . I just bought a dvd player flipdown. what wiring will I need to get it to run thru to the circuit board. I have a Nissan Altima 2013
Nice video, good work! Always great to see creativity put into little mods like this. Not too many mechanics will give such detail but I'm glad you do. Always look forward to the next uploads :)
That seemed to be a big job, nice work Eric!
Ya gotta have a magic screw pile in every shop! Great vid Eric.
Wish I new were to buy your electrical probe with the alarm what model and manufacturer is that tester your using eric
If you're worried about a rattle inside the DVD player I would rap the ends of the RCA cables with electrical tape and that should keep them from rattling.
Hi I have a question did you hook up the add circuit thin on a exist fuse for te acc ? And where did you get power for the constant one?
Thanks for the video.How do you setup the audio via FM transmitter?
4:44 "I may not take it all the way out." does exactly that puts it on the roof no less🤣🤣
Could you suggest some type of support for a heavy flip down DVD player with a sunroof?
Does the ground have to be the same thickness as the power wire? For example if I use the 12 gauge ad a circuit and run 12 gauge power wire from it to the unit, can I use the much smaller ground wire coming out of the unit without hurting anything?
Just to get an estimate how much would you charge to install one of these DVD players
hello i see last time someone left feedback i think but ,,, anyway ,,, i have the add a fuse line ,, but finding the power for dome lights i have the white and wire and blue but the others purple and another light blue so should i do the middle which is blue and looking at the add a fuse hard to find the fuse for rear wipers and i see that others say they never take the head liner down ,, I didn't take mine down,,, but love this video and i have the 2013 honda odyssey thanks but need some info...
how good are the 9V memory savers; compared to larger ones or more expensive ones?????
I bought the same Boss DVD player to install in my sisters car and remembered watching this. She has a Acura MDX 2006, which is nearly similar to Erics install here. Too bad you didn't show how to remove the headliner cause that was a pain. Installed a Android stereo as well and wired audio and video to and from both devices, plus a reverse camera. That took me at lest 3 full days to install it all.
Were having a problem with the remote to the dvd player.
Seems to be giving out. How do we program a new one?
Brand Nitro TF
model # BMWx-15XGE
I installed this DVD Player and everything is fine.. Now When I turned off the car and turn it on again. I have to go and turn the DVD manually even though I left it on. Is it normal? I know the DVD starts from where I left off without any problem. The Problem is that even if I'm in the HDMI Mode when I turn it off and on it would start on the DVD instead of the HDMI input. Also I have to turn it on with the remote or manually all the time. Any Suggestions?
I have a 2005 Uplander and I like to hook up my DVD player to this vehicle but how can I go about it because this other DVD entertainment center came from another hot highliner that was made for it and mine I don't have the wires that goes to it what can I do. !
Where can i buy those exact wires that you used to connect it together? Did you used a 16 awg wire?
Looks MINT! I thought newer headliners were fiberglass, which makes me think it would hold up alright to having a dvd player hang from it. Then again you do have kids, which tend to be hard on things. Haha. I was cringing when you were lining up the template. I remember drilling out holes to mount a roof rack system and thinking to myself I hope these all line up.
16:29 Wasn't that black box on the red wire an inline fuse?
Good video Eric. Thanks for sharing!
Glad you got it to work. It was good you didn't have to call Boss tech support. I have a head unit from them with a little 3 inch screen on it. I can't get tech support to help me out at all with my question on it. They answered me once and I asked a couple follow up question and they never respond. I would not use them again passed on there very bad tech support
I have a 2005 Ford Expedition Eddie Bauer Edition. I just install a Jenson VX7020. The factory DVD player in the back is not working. Any ideas would be great thanks...
Hello man,I bought 2008 VAN Vw Touran i have almost same dvd player Boss.Everything is connected properly,but have no sound.Can u help me out ?
My dvd of 2007 Honda Pilot RES, does not work any more as it tries to be on and make some dvd loading noise. Kids does not use it any more as they moved on to tablet, how do I just turn it off? I tried to power off, but every time key on, it makes noise for 2/3 minutes like trying to load dvd...how do i remove it?
Eric, you'll always be our hero for life, whatever. :D
Eric, does this DVD player play iPad or iPhone movies through the USB port?
I have my Toyota sienna,dvd screen installed by a certified "tech " but it continuously drain the battery. so I unplugged it,whatcould have done wrong??
you should convert all your interior lighting to LED. would take a lot of amp load off of the circuits and then you can tie in whatever you want.
Good job assuming you'll need a stronger mounting surface such as the cross members.
Brilliant video chief! Thanks!
Nice one! Great video to watch.
When it like that hanging bolts with 3 nuts. All thread bolt cut to length. long as you tighten it it's stable as 4 boxed legs
Would this work on my 2000 Toyota Sienna XLE??
Great video, very informative, good job...
What other "pimp my ride" type videos do you have?
Very nice work nice installation
Great video Eric, dragging that headliner in and out must have been fun. Drilling into the headliner would have been the most nerve-wrecking part for me also. I would be SO pissed If I made a hole in the wrong spot!
Did this a few years ago in my dads Astro. Trick it out with a custom input jack, 300w power inverter for games, and off air ant for the car.
It doesnt get any use now. Can't pickup HD signals, dont own anymore DVD's, and games are all not in HD.
Still looks good tho!
What a nice van! I'm jealous.
Your ground is good. You should always keep ground wires short and connect them directly to the body of the car. That will always have less resistance than a wire to the ground terminal of the battery. Don't run grounds to the battery. You dun good with the ground, just the way it is.
The 12V constant wire should be red! Other people might work on your van someday. It is irresponsible to use non-standard wire colors. It would be best to run it directly to the positive battery terminal and fuse it within 12 inches of the battery. The 12V switched wire should go to the accessory wire from the ignition. That wire should be yellow! Also, solder your splices into the wires directly or use scotchlocks to attach the wires. Don't "redneck rig" your power wires to the fusebox. Even if someone sent you a fancy adapter, it's not the right way to do it and you know it.
While you had the headliner out, you should have run RCA cables to the radio area. Don't depend on the crappy FM modulator.
Nice Channellock crimper! Those crimps work great. I've never had one fail. You don't need to solder everything.
what was the total cost and time spent to do it ?
NOOOOPE!! not doing all that🤣🤣🤣 amazing video!!!! By the way 👍👍👍
I've used the add-a-circuit many times.
awesome vid eric ! thanks !
Pretty clean install!
I see that dvd player has an HDMI port on the driver side, can you plug in lets say a laptop or gaming console to it? awesome video by the way Eric!
Maybe, someday when I can afford a shop, and better video equipment, (and the know-how to edit the videos) I'll be able to get free stuff too... lol
LOVE your vids Eric! Would love to work along side you!
Wow you wanna do what, and at his shop..??.. "Work alongside with Eric, I don't think So".. I guess you no clue as to how impatient Eric is around the work shop.. if you do something incorrect around him.. You will pay nearly with a body part of yours....
Thank you I will do it for my 1996 Nissan quest when this van is modified
Why didn't you use bullet connectors for the power/trigger/ground wires? It would make it easier if you ever have to remove it.
Open the screen and have someone hold it in the place your considering installing it, sit in the driver's seat and see how much the screen blocks your rear-view. Had a factory DVD on a Ford Freestar and it blocked too much of my view out the back window.
what happens if and when that crappy dvd player dies? now you have a bunch of holes in the headliner and nothing to show for it.
Eric,
Big fan. Love your videos and what you provide for your viewers. I'm not sure if you did this, but here is a suggestion: Bench test car audio electronics before committing to installation. I learned that lesson the hard way. Thank you sir.
Best video thus far!
The sharpie worked ok I guess, but what I would have done differently is install the mounting screws into the roof bracket, put some sort of paint on the heads of them, then mock the headliner into place. The paint from the mounting screws would then transfer to the back of the headliner giving you your locations to drill.
Brian W Nice idea. I'll have to try that next time.
no need for for paint, just press the head-liner against them and it will mark the position :)
Yeah, that would work too
Edos. Unidos, ¿y como luciría en Europa la Odyssey?
This is seriously hard work
Hey Eric, i know this might not be the right video to be making this request, but would you be willing to do a video on valve stem seal replacement? I am working on a 1998 Mitsubishi Eclipse, with a 2.4L 4g64 engine. I do not plan on pulling the head and will be using the same technique shown in your valve spring removal video. However, it would be great to see how properly remove the seals, how to identify a failing seal, and how to properly install the new seals. I also have a somewhat persistent tick.While the rocker rails are off, it only makes sense to replace the lifters as well. Maybe you have done a video I haven't stumbled across yet, but there are several videos on youtube with different methods of bleeding the lifters; some people aren't bleeding them at all. What is your take on this? I already ordered the parts, so there is a good possibility the job will be done by the time you would be able to do such a video; however, it seems like a common job and a walkthrough from a trusted source would do us all well. Keep up the great work.
You are the man, Eric
Nice install!
how to connect music player display wire to lcd roof
Cool install! I found it easier to add circuits to my truck by building a separate diy fuse/relay box. Amazon always has excellent deals on fuse holders, fuses, and 30 amp relay connectors (relays included)! I've spliced from the hot switch wire of the ignition and had zero issues.
Brian Piper I'm actually going to do that with the Fairmont. Thanks for the suggestion.
I don't think people say this enough but I really appreciate Cameraman Brian, He's really helped take your channel to a new level. Great work Eric, That install looks nearly factory. :)
I sure hope that's a good quality dvd player and display after going through all the trouble to get it in there. If it burns out and breaks in a week I'd be pissed.
Hello Eric love you youtube show just was watching you instal your dvd player. I was wondering how can i play from my galaxy phone youtube videos on my dvd player can you please help thank you.
Very good job sir! Huge fan! Love watching your videos!
In car DVD player? Is it 2002??
Some lights what is a batter positive is that the B+
Was the video just 25min long? or something weird is going on with YT?
Eric, you could later change the bulbs in the DVD player to match up with the dome lights :)
Screw halogen bulbs!
I would have put crimpable blade connectors so you can un plug the wires from each other if you need to take it down
Man just get to the wiring of the thing, i like your videos so im watching till the end , but the only thing complicated to me about that project is the wires. I am an idiot with wires and elec.all i know is red to red and black to black after that im lost. Cool video though, i like em all.
Por fin un vídeo bien hecho sobre la instalación de este equipo, gracias.
Nicely done .
i use to solder, but crimp is just so much easier and if done right is just as good connection.
Me too, I prefer to use non insulated butt connectors and heat shrink for most of my connections.
Great tutorial video, tnx. for me it is the most unplesant part of our work to install stuff like that. They can't live without television, uh? Angry!
I'd be a little concerned with possible video interference caused by the wiper motor when it is engaged.
Well done Eric, where do you get those wire strippers from? Bloody good vid. Johnno
John Kinnane Link in the description along with the other tools used in the video.
good video sir,. thanks
Note to self and others.
Remove metal bracket from dvd player, place to desire location with Headliner still in the vehicle take black marker put dots on headliner for drilling through. Then remove headliner do a mock up install with either piece of fiberglass or piece of scrap metal laying around.
Rule of thumb measure twice drill once.
What
Hey Eric, huge fan of the show iv seen many episodes and always keep up to date on your newest videos, just wondering about the crimping pliers in the video, recognized them as a channel lock unit and iv been tossing back and forth between getting a pair of channel lock crimps vs klein. I work in the HVAC field and the guys usually buy kline but iv always had good luck with channel lock personally. just wondering how you find them to use and do they hold up well. also any experience with kline? thanks for the video hope to hear from you.
Great video
very nice Eric... people should be able to follow your helpful instructions on how to do this install.. thanks Eric... very helpful....
Nice video. Thanks
I would have used a ACC circuit.
good work.
thanks Eric!!!
Don't ever drill into the cross members the way he has (perhaps why the video is cut), it's a sure fire way to go all the way through the roof panel on the other side.
Either mount the bit deep in the chuck or use self tapping screws that can't reach the skin
Your location?
Awesome and interesting thx ,,,,thumbs up
How to do the title:
Step 1: go to wal-mart
Step 2: find the radio head with popout screen and dvd player
step 3: buy
Step 4: Install said unit
Step 5: pop out said units screen and realize that it interferes with the shift selector.
Step 6: Go to Walmart and leave with beer instead of a refund because they don't let you return electronics.
Step 7: Drink Beer
Step 7: drinkkk anoathers
Step 8: get baseball bat and hit that mfer out of the park.
Step 11: wake up and have no regrets.
4 years ago
Eric, as a person who typically does the twist, solder, glue-heatshrink method, I have no problem with crimp connectors as long as they're done right and with the right tools. Most of the time people use pliers or a hammer, or they'll use crimping pliers, but they'll use the ones made for noninsulated crimp terminals and end up destroying or penetrating the insulation. Yours are dual purpose by the quick glance I got at them (and looking at the link) both insulated and noninsulated crimping terminals. A connection like that I have no problem with at all!
Very cool, very hip!