Tesla Model 3 | Model Y ⚡️ Spoiler Install + Review | Real Carbon Fiber 🔥 Hansshow
Вставка
- Опубліковано 18 кві 2022
- If you are looking to add a spoiler to your Tesla Model 3 or Tesla Model y that looks very similar to the OEM Tesla spoiler from tesla.com, you may want to check out hansshow’s new spoiler that is made 100% of real carbon fiber.
____________________________
See MORE Accessories! 👉🏻 evanmichiels.com/general-2
Carbon Fiber Spoiler 👉🏻 amzn.to/3Eqb2aK OR bit.ly/3xJUE3n (Use Coupon Code "TeslaEvan")
Heat Gun 👉🏻 amzn.to/3jSV1k6
Alcohol Prep Wipes 👉🏻 amzn.to/3xTWz5N
____________________________
I wanted something that matched the OEM tesla spoiler but of course was not looking to spend a ton of money on it. From hansshow you can get this carbon fiber spoiler for both the model 3 or model y, and it comes in both glossy carbon fiber or matte carbon fiber. I chose the matte version as you can see here and first impression had me quite surprised with the quality and fit formation to the trunk. Installing this took me less than 5 mins as it was quite a breeze to affix it to my trunk.
The first task we need to do is wipe off the rear truck with a moist microfiber towel to remove dirt or dust. After wiping this down, take your finger and glide it across the top. If you feel and roughness like a gritty feel, you may want to use a clay bar application on your tesla to remove these imperfections. If you don’t, I took one last wipe down with an alcohol sheet to further remove any final imperfections.
Take your spoiler and affix it to the truck without removing the adhesive backing. Get an idea on where it should be placed by measuring on both sides of the spoiler. In my case for the model 3, it was just about 5 inches on both ends from the panel gap to the very edge of the spoiler for the perfect center placement. I used painters tape to mark my position on both ends and finally one larger piece down the middle using a sharpie pen to mark the center. Use a blade to cut the top from the hood of the trunk and the spoiler.
After we have the tape placements correct, simply pull back the adhesive backing tape to expose the sticky side of the spoiler. Now I only took off half and left the remainder in place just in case I needed to re-adjust the spoiler. However, from my experience I would just pull off the entire adhesive backing and stick it to the trunk to make the installation process easier. Be sure to align the markings on the painters tape with the line we created earlier. I started with the center and pushed hard from the middle working my way outward.
You can see I have a little difficulty removing the final red tape on the other half of the spoiler which is why I recommend just removing it all at once before placing it.
This part is not required, however, if you have a heat gun, I would recommend using it to help the adhesive material really stick to the back of your tesla. You might want to place more painters tape on it to help the spoiler cure for a few hours after installation. It’s totally up to you, this is not required.
After installation, I was really happy with how it turned out. I think it gives my tesla a more sporty look while also matching the OEM stock look. I have a link below this video showing you where to get this should you feel you can tackle this job on your own. Again, installing this was not hard at all. Just take your time and you’ll be happy with how it turned out.
If you're looking to see even more accessories for your tesla model 3 or model y, be sure to check out my new website at evanmichiels.com to see every item I have showcased on my channel this far. Until the next video, stay safe and I’ll see you on the next one
Tesla Model 3 | Model Y Spoiler Install Review | Real Carbon Fiber Hansshow
#model3spoiler #modelyspoiler #teslarealcarbonfiberspoiler - Авто та транспорт
See MORE Accessories! 👉🏻 evanmichiels.com/general-2
Carbon Fiber Spoiler 👉🏻 amzn.to/3Eqb2aK OR bit.ly/3xJUE3n (Use Coupon Code "TeslaEvan")
Heat Gun 👉🏻 amzn.to/3jSV1k6
Alcohol Prep Wipes 👉🏻 amzn.to/3xTWz5N
thanks! ordered one a few days ago, so goin to use your installation guide once it's delivered!
Nice one and thanks for the demo…
I have similar but a EU version. It really adds sportines to the car. The installation is easy and did the same u did, only difference was that I had to heat up the truck lips a bit as it was still winter here in Finland. I put the tapes on it for few hours just to be safe.
Thank you! Ordering one now
Hope you enjoy it!
Great video! Simple and straight to the point.
How’s it holding up over a year now?
did you use the 3M adhesive promoter? and how long did you let it sit before you drove the car? thanks
No I did not… be sure to wipe the area with an alcohol wipe and let it sit for 12-24 hours
@@EMtesla1 thanks man!
@@EMtesla1 You will come to regret that. Please folks use adhesion promoter
Alrighty then. The spoiler is still held on my car great. Thanks for your comment
@@EMtesla1 you are most welcome
How’s it holding up?? Thank you
Still no fading or cracking!
hi
How's it holding up?
Still on my car to this day. No Issues of fading or cracking.
@@EMtesla1 thanks
Don’t get the gloss carbon fibre they are wavey looks like real bad orange peel
I’ve emailed Hansshow the are communicating with me but can’t see any issue it will not be going on the car that’s for sure