My dad had a 1980 Johnson 25 hp long shaft tiller model and it had Both Electric and rope pull start. It was a great little outboard that would make a 14 ft Deep Fisherman Mirrocraft fly. Good video.
I got an 2018 E tec 25 hp evirude short shaft electric starter. It is attached to a 1448 Tracker grizzlly all welded with myself and one other fat guy it will do 27 to 28mph! That's also with a 55 lbs minn kota bow mounted trolling motor and one very large AGM battery and humminbird helix 7.
You can always remove the trim rod (tilt pin) while in shallow waters keeping the tilt lock lever in the down (lock) position. This way the outboard can be raised up and down without getting locked. Just ride slow and watch out from engine rising out of water while in reverse.
Got the same motor! I run it pretty shallow too, around sandbars. So I agree the manual tilt is a bit cumbersome. Another thing I’ve noticed is the mounting clamps come loose fairly often. Not sure if this is common with clamp style mounts seeing as how this is my first outboard, but I definitely can not complain!
2003 25hp Nissan/tohatsu. Over the years ive built it out. It pushes my 1519 Duracraft 38mph. Its a single coil two cylinder two stroke. The weight is fairly low weighing around 115#. Finding that balance between weight and output.
I found these on boatseats.com. I think the number was 3166 wise seat. They are not cheap but in my opinion they are worth it. They are so comfortable. And the arm rests is a must have . I can sit there all day and not catch fish and still be happy.
What is the model number for your motor? And is it still running great? I have a suzuki that just messed up on me. I'm wanting to get a 25 to replace it. Thank you for sharing 👍
I think it is a f25la . Still running strong. I've had 10, 25, 30 ,35 and 40hp tillers. I will say this is the smoothest and best one so far. However my old evenrude 10hp on a 12ft jon would fly for such a small rig. ! Still go them too
Any regrets on the lowe boat? Great set up. Best value for fishing fresh water anywhere on the planet in my opinion. entire boat not to heavy and seems like plenty of room. Been looking a long time and have settled this combination is the the best value. not sure about the boat brand.
I actually looked for this boat. It is rivet boat . Not thick ga aluminum. And low cost . But!!!! My friend had one 20 years ago the 1448 big Jon and it made a believer out of me. It has a big advantage over the heavier boats. It is much faster. And the draft is almost nothing. This boat will go in inches of water . It is amazing how shallow it will go and also extremely stable. So this is my reason for getting it. If I was buying a jon boat again. I would buy the same one. That front seat is just the cats meow!!!
It is long shaft. 20" I made sure when I got the jon boat to get a full transom. I did the short shaft for years . But I believe in the full transom. It keeps water out when letting off the gas . Especially when in rough water.
Does it have any kind of friction adjustment for steering? My Honda has a little lever that you can increase the friction so that it doesn't go where it wants if you take your hand off the tiller for a minute. It's super handy.
This motor sips fuel even running at wide open. Had initial issues as mine was one if first motors, I pull.it out start it now and then, drain fuel oil put it away. It's my backup motor now, still love the light weight.
Great review. What kind of range do you think you will get on a 3 gallon tank? I wish someone would do a 25 vs 25 high thrust comparison. I can't find one anywhere.
@@omieyouknowme Mmmmmm...!!! Ya !! 3 Gallons is risky Business. Considering days with high winds and non stop waves FOR HOURS ahead. Needing more energy to go through resistance. In this scenario, your OCTANE doesn't help at All..Hahahahahahhhhhhhha..!!
I had one of these motors for about 2-3 months and one day I went to go start it up and it wouldn’t go. I took it to the dealer and after a month they came back to me and said that it was the wiring harness. I got a replacement motor and I’m supposed to get the boat back this week. Hopefully I didn’t get another lemon.
@@ACPro oh ok thank you. I was thinking it may be a T25 high thrust yamaha. The top end speed you're getting out of a 1648 is impressive. Thank you again for sharing.
I worked at a dealer 10 years ago . Got the most complaints on these little Yamaha 4 strokes, customers would shit their pants on performance loss vs weight
I love mine. Started with a Johnson 9.9 then and 1976 25hp upgraded to a 30hp electric start 1990 Johnson. There is no comparison. This thing is like having a hot naked girl on the boat . Just great all way round and people enjoy seeing it too.
Great motor. I just wish it was easier to buy one. I placed a order for a brand new Yamaha 25 over a month ago and they tell me (MAYBE) I will get it by December. Seems impossible to find one right now. All dealers I call same story.
Good I ask you a 40hp and 30hp Yamaha how much come out long leg 4tienpos of those new or used. Thanks I'm from Uruguay. If you have any phones we make it graci
I don't think they sell this version in that market, they do sell the 20hp version but not the 25hp version for some reason(you may be able to order the f25 version from the distributor). If you need a 25hp motor get the Yamaha Enduro 25 which is a lot older technology and uses pre-mixed fuel but it is reliable. Don't get the 25 BMHS (S / C) unless you need the safety lanyard. The f20 may be a better choice than the 25 BMHS (S/C) if you can't order the f25 and you can live with 20 hp. If you're planning on taking it into the ocean and the boat can handle it get the enduro 60 or 75 (also uses premix). For a larger panga get the 75, for a smaller one use the 60. If you only need 25 hp get a 25 enduro that wasn't used commercially.
My 25hp 4stroke Yamaha has electric start wit wheel and controls. Sometimes when I open throttle full speed there’s time it doesn’t go as fast as before . What is the remedy to fix this without a mechanic .
Actually these are Oakley and wear them alot I'm my videos. They have been around the world with me ma y times. Secret is they are prescription so they help me see what I'm doing!🤣
I couldn't really tell from the video, but it appeared that your boat got up on plane. Can you verify this? I have a 14 ft V bottom and I need a motor that'll get it up on plane.
Bought one of these motors this week, first ride, it worked for 20 minutes and died. Took it back and a new motor was put on, will try the new replacement on Friday, even Yamaha is not exempt from lemon motors. Will update this on Saturday😡
David Nguyen yes, in a boat package, worst buying experience ever and i have an extensive career in sales myself . It outright died in the middle of a lake and i limped back at idle speed. They say they found a problem but wont reveal what that was.
How much did you pay out the door for that? I have a 1984 Yamaha that took a shit on me, and because it's so old nobody is willing to work on it, so I'm basically forced to buy a new one.
Listen..!! This F20 Yamaha as more than 362 cc like was the previous ones till 2020. it's now got 462 cc and the displacement is worth to see , because now you can maximise your propeller to the max with a big pitch. and you have the same motor as the F25 witch is also 462 cc. Amazing stuff again as you can convert your F20 to a F25 by changing the computer Box and the spacer
Sorry the 20hp rating is at the prop at 5500rom, the tohatsu 20hp is almost 30lbs lighter. 20hp out of a detuned motor is kind of throwing money away. Rather get a motor maxed for displacement. The ECU for all these little motors is mitsubishi.
@@omieyouknowme I would say that the volume * V=TT X r2 X h * push of the piston at 462cc is worth the money. If you do compare the other 20 hp at lower cubic engines witch explain the lower weight of the unit .* I do understand that *. Nevertheless, the power generating the output by compression, is a big help, when the capacity of the boat is in average + load again. I say that the pitch of the propeller this time is more respected with a 462 cc by constant energy content. * Piston stroke in feet = Propeller revolutions * at 5500 rpm by extrapolation. And by changing the ECU, which is controlling the amount & timing of fuel intake, Cannot be done without enlarging the air intake, for a proper conversion to achieve 25 hp. Don't even think enlarging the air intake by keeping the same ECU as it would overheat the pistons having to much oxygen.
@@JohnJohn-tf4cr I understand that there is no replacement for displacement, the yammie per site says is 432cc btw. I'll verify with service manual. As for prop size, yes you are swinging a slightly larger prop on yammie vs the tohatsu, but the motors are rated at shaft hp at 5500 rpm in the prop. I would love a comparison in the same boat by someone, see if the extra displacement and weight affects anything. Take the yammie vs lighter tohatsu and Suzuki which both weigh under 100lbs in bare short shaft trim.
@@omieyouknowme Mmmmmmm....ya , The weight of the motor as to be consider, in this matter. Yammie's are heavier to carry for & on, that same Boat in a speed test. Ohhh ya ...Resistance is the name of that game. Lighter Boat = heavy motor = Lighter Boat Yamaha does have the power at 432 cc but any sort of resistance, is questionable. As is the water spreading or the shape of the boat, is never gonna give us an answer. I understand that 432cc as the power indeed, but i do have a SHAFT to consider. hahahahahhhahahahahahha...........!!! As for Connecting Rods on a motorcycle indeed. I do have my F20 / 2021 on a 16 1/2 aluminium boat. Having this 432cc is a good move,. Nevertheless if I want to consider using all of it, Ill have to change the ECU and air diameter intake. Tanks Man. You make my day
@@JohnJohn-tf4cr I ran the f25 when it first came out, with just me after the motor warmed up it lost almost 500rpm. Yamaha would not believe me, so I made you tube videos. Took the cowl off and had the extra 500rpm back. They eventually reflashed my ecu I'm curious if run the motor first thing in morning, then at mid day when it's warm, do you lose rpm as well? My solution was I actually cut a hole in front of the intake, 3d printed a ram air snorkel for it. Of course sold the motor right after as I got a screaming deal on a 40hp.
@@ACPro nice im really considering upgrading to a 4 stroke this season,, jus because of how old my mercury 2 stroke is, haha. The only thing holding me back is how heavy 4 strokes are,,,
@@ACPro OK, metric has been standard since about 1880. Not sure why you use imperial measurement still. You should state the speed in KM/H as normal so everyone understands. Good luck.
World is diffrent in different places . This is not a 19kw. It is 25hp. Like described. When you understand this you will be more diversified and have a wider knowledge of how the world works. There is 2 systems standard and metric. We use the standard however we are smart enough to know and recognize both. People also use different languages. We can recognize them too.
My dad had a 1980 Johnson 25 hp long shaft tiller model and it had Both Electric and rope pull start. It was a great little outboard that would make a 14 ft Deep Fisherman Mirrocraft fly. Good video.
great Video. I'm just considering buying an F25 now. My boat is same as yours but a 1448. It should fly with it.
Great video. Nice and THOROUGH!!
Hard to get THOROUGH outboard videos!!
Thank you
Nice seats and sweet boat
I got an 2018 E tec 25 hp evirude short shaft electric starter. It is attached to a 1448 Tracker grizzlly all welded with myself and one other fat guy it will do 27 to 28mph! That's also with a 55 lbs minn kota bow mounted trolling motor and one very large AGM battery and humminbird helix 7.
Thanks for the video. I have 1648 monarch, looking at getting a 25 hp. Just starting research on what manufacturer.
Glad I could help
You can always remove the trim rod (tilt pin) while in shallow waters keeping the tilt lock lever in the down (lock) position. This way the outboard can be raised up and down without getting locked.
Just ride slow and watch out from engine rising out of water while in reverse.
Got the same motor! I run it pretty shallow too, around sandbars. So I agree the manual tilt is a bit cumbersome. Another thing I’ve noticed is the mounting clamps come loose fairly often. Not sure if this is common with clamp style mounts seeing as how this is my first outboard, but I definitely can not complain!
I had to tighten mine up a few times too.
Tighten clamps then zip tie them together.
I had a 25 mercury, I used to lock the mounting clamps with a padlock, that will keep them from loosening and will prevent theft
@@davidb8397 I ended up buying a lock for the clamps. Thinking about just getting the motor bolted on now though.
@@n0llie good that'll work
2003 25hp Nissan/tohatsu. Over the years ive built it out. It pushes my 1519 Duracraft 38mph. Its a single coil two cylinder two stroke. The weight is fairly low weighing around 115#. Finding that balance between weight and output.
Very cool!!!
Hey Toby, Where did you buy those seats & do you know what model they are ? Looking for some new seats for my 14 footer & they look perfect !
I found these on boatseats.com. I think the number was 3166 wise seat. They are not cheap but in my opinion they are worth it. They are so comfortable. And the arm rests is a must have . I can sit there all day and not catch fish and still be happy.
I have a 15 hp on My 200 pound with a minn kota terrova in bow it runs 36 kmh its great fun .thanks for sharing
Thank you for sharing!!
What is the model number for your motor? And is it still running great? I have a suzuki that just messed up on me. I'm wanting to get a 25 to replace it. Thank you for sharing 👍
I think it is a f25la . Still running strong. I've had 10, 25, 30 ,35 and 40hp tillers. I will say this is the smoothest and best one so far. However my old evenrude 10hp on a 12ft jon would fly for such a small rig. ! Still go them too
Any regrets on the lowe boat? Great set up. Best value for fishing fresh water anywhere on the planet in my opinion. entire boat not to heavy and seems like plenty of room. Been looking a long time and have settled this combination is the the best value. not sure about the boat brand.
I actually looked for this boat. It is rivet boat . Not thick ga aluminum. And low cost . But!!!! My friend had one 20 years ago the 1448 big Jon and it made a believer out of me. It has a big advantage over the heavier boats. It is much faster. And the draft is almost nothing. This boat will go in inches of water . It is amazing how shallow it will go and also extremely stable. So this is my reason for getting it. If I was buying a jon boat again. I would buy the same one. That front seat is just the cats meow!!!
Will the variable trolling RPM switch allow for trolling at speeds under 2 mph?
I appreciate your review I’m about to buy exact same.. is yours a short shaft? Cheers
It is long shaft. 20" I made sure when I got the jon boat to get a full transom. I did the short shaft for years . But I believe in the full transom. It keeps water out when letting off the gas . Especially when in rough water.
Hey thanks for your informative reply! That’s really helpful for me!
You can remove the mechanism that will disengage the auto shallow water drive. It will allow you to manually set it.
Thank you!
Does it have any kind of friction adjustment for steering? My Honda has a little lever that you can increase the friction so that it doesn't go where it wants if you take your hand off the tiller for a minute. It's super handy.
yes it does and it is nice to use when trailering you can keep it from swinging
28 mph is flying! nice.
This motor sips fuel even running at wide open. Had initial issues as mine was one if first motors, I pull.it out start it now and then, drain fuel oil put it away. It's my backup motor now, still love the light weight.
I have a 20hp and I love it
It's more then what I need for power
I ride half throttle. It's quiet.fuel burn 🔥 is low
Great review. What kind of range do you think you will get on a 3 gallon tank?
I wish someone would do a 25 vs 25 high thrust comparison. I can't find one anywhere.
3 gallon of Gas wot will go all day!!!
@@ACPro I have done 21 miles on 3 gal. Running 5000-5500 rpm when I had motor.
@@omieyouknowme Mmmmmm...!!! Ya !! 3 Gallons is risky Business.
Considering days with high winds and non stop waves FOR HOURS ahead.
Needing more energy to go through resistance.
In this scenario, your OCTANE doesn't help at All..Hahahahahahhhhhhhha..!!
@@JohnJohn-tf4cr it was still a great little motor, I see quiet a few for sale on craigslist now, wonder why.
Where did you bought it?
Cảm ơn bạn đã chia sẻ kinh nghiệm Chúc bạn một ngày tốt lành nha
Got the same. Only dropped to 25mph with 2 people in the boat
I had one of these motors for about 2-3 months and one day I went to go start it up and it wouldn’t go. I took it to the dealer and after a month they came back to me and said that it was the wiring harness. I got a replacement motor and I’m supposed to get the boat back this week. Hopefully I didn’t get another lemon.
Thank you for the comment your are 2nd person to seem to have a bad motor that was brand new.
Also i was wondering what the gear ratio was on your lower unit? Thank you for sharing.
2.42 -1
@@ACPro you said the gear ratio on your 25 yamaha was 2.42:1. I have looked all over and i cannot find a 25 Yamaha with that gear ratio.
Sorry I not sure how that was typed. Either I didn't look at it right , fat figured or auto correct. It is 2.08. Good catch
@@ACPro oh ok thank you. I was thinking it may be a T25 high thrust yamaha. The top end speed you're getting out of a 1648 is impressive. Thank you again for sharing.
I worked at a dealer 10 years ago . Got the most complaints on these little Yamaha 4 strokes, customers would shit their pants on performance loss vs weight
I love mine. Started with a Johnson 9.9 then and 1976 25hp upgraded to a 30hp electric start 1990 Johnson. There is no comparison. This thing is like having a hot naked girl on the boat . Just great all way round and people enjoy seeing it too.
Mileage.?
Please try and take a guess on the boat in this video. I run long distance on the black River. 28 mph sounds adequate.
Yes I am very happy with the speed it delivers and very good on fuel too!!
How is the low RPM vibration? I keep hearing about it maybe being shaky? Or is that over blown? I plan to use mechanical controls, not tiller.
This thing is so smooth its incredible. You will here mouth from people on everything. But they are just mouth .
@@ACPro well, I ended up buying one with mechanical steering and power tilt and trim
Great motor. I just wish it was easier to buy one. I placed a order for a brand new Yamaha 25 over a month ago and they tell me (MAYBE) I will get it by December. Seems impossible to find one right now. All dealers I call same story.
Ordered mine June 30th pick,pick it up today Sept 26th 2020
Hey matt I think we’re in the exact same situation. Which region are you in?
@@paullam007 I am in North San Diego County. Ordered through JP Motorsports. I am thinking to try and with to Suzuki 25.
Fingers crossed!
I'll sell you mine 3000
Ive got the 2017 model on a 542 war eagle and get just about the same speed
great thank you
Put a 2' extension on your controles, I bet you could pick up 5 mph sitting a little forward.
Good I ask you a 40hp and 30hp Yamaha how much come out long leg 4tienpos of those new or used. Thanks I'm from Uruguay. If you have any phones we make it graci
I don't think they sell this version in that market, they do sell the 20hp version but not the 25hp version for some reason(you may be able to order the f25 version from the distributor). If you need a 25hp motor get the Yamaha Enduro 25 which is a lot older technology and uses pre-mixed fuel but it is reliable. Don't get the 25 BMHS (S / C) unless you need the safety lanyard. The f20 may be a better choice than the 25 BMHS (S/C) if you can't order the f25 and you can live with 20 hp. If you're planning on taking it into the ocean and the boat can handle it get the enduro 60 or 75 (also uses premix). For a larger panga get the 75, for a smaller one use the 60. If you only need 25 hp get a 25 enduro that wasn't used commercially.
No idea
My 25hp 4stroke Yamaha has electric start wit wheel and controls. Sometimes when I open throttle full speed there’s time it doesn’t go as fast as before . What is the remedy to fix this without a mechanic .
First thing I would do is change fuel filter. If you haven't ran it much change the gas and add seafoam to the tank. Start with the basics.
Hey. What are the sunglasses your wearing? Thx
Actually these are Oakley and wear them alot I'm my videos. They have been around the world with me ma y times. Secret is they are prescription so they help me see what I'm doing!🤣
My futur motor ! For my flouka in tunisia !
For fishing and sun !
Very Nice marine motor ! 😉
Think .. for this vidéo !!! 😁
It has been a good one. Love it!!
Just curious how your front pedestal seat is mounted!
I welded a aluminum c channel in the floor and aluminum sqaure tuning uo to a swivel base
Engine book kaise
What is your boat's length?
This boat is 16 ft and 4 foot wide
I couldn't really tell from the video, but it appeared that your boat got up on plane. Can you verify this? I have a 14 ft V bottom and I need a motor that'll get it up on plane.
It's on plane in seconds. This little motor is strong I love it.
Bought one of these motors this week, first ride, it worked for 20 minutes and died. Took it back and a new motor was put on, will try the new replacement on Friday, even Yamaha is not exempt from lemon motors. Will update this on Saturday😡
Yes please keep up updated.
Had boat returned yesterday, haven’t tried new replacement yet but the dealership will not tell me what the issue is! Hmmmm.
@@johnnash7481 That is very fishy indeed. Was the original motor put on by the dealership?
David Nguyen yes, in a boat package, worst buying experience ever and i have an extensive career in sales myself . It outright died in the middle of a lake and i limped back at idle speed. They say they found a problem but wont reveal what that was.
How much does it weigh? Looks like about 110+?
126lb thank you for sharing
Hey, how do you do to charge the battery? I see in the video that you have a black cable to a battery
I just connect charger directly to terminal block.
@@ACPro what its your models??
My models is F25 gmh and i cant charge the battery, i’ve the red outpout but dont have voltaje
@@diegonoriegagomez2487 you may want to check your fuse if it was used with battery and wire grounded it will blow the fuse
How's that oil filter on a oil change, messy?
Not bad . Put rag under the area before you take it off and it wipes up easy. .
How much did you pay out the door for that? I have a 1984 Yamaha that took a shit on me, and because it's so old nobody is willing to work on it, so I'm basically forced to buy a new one.
It was right at 3800
Listen..!! This F20 Yamaha as more than 362 cc like was the previous ones till 2020. it's now got 462 cc and the displacement is worth to see , because now you can maximise your propeller to the max with a big pitch. and you have the same motor as the F25 witch is also 462 cc.
Amazing stuff again as you can convert your F20 to a F25 by changing the computer Box and the spacer
Sorry the 20hp rating is at the prop at 5500rom, the tohatsu 20hp is almost 30lbs lighter. 20hp out of a detuned motor is kind of throwing money away. Rather get a motor maxed for displacement. The ECU for all these little motors is mitsubishi.
@@omieyouknowme I would say that the volume * V=TT X r2 X h * push of the piston at 462cc is worth the money. If you do compare the other 20 hp at lower cubic engines witch explain the lower weight of the unit .* I do understand that *.
Nevertheless, the power generating the output by compression, is a big help, when the capacity of the boat is in average + load again.
I say that the pitch of the propeller this time is more respected with a 462 cc by constant energy content. * Piston stroke in feet = Propeller revolutions * at 5500 rpm by extrapolation.
And by changing the ECU, which is controlling the amount & timing of fuel intake,
Cannot be done without enlarging the air intake, for a proper conversion to achieve 25 hp.
Don't even think enlarging the air intake by keeping the same ECU as it would overheat the pistons having to much oxygen.
@@JohnJohn-tf4cr I understand that there is no replacement for displacement, the yammie per site says is 432cc btw. I'll verify with service manual.
As for prop size, yes you are swinging a slightly larger prop on yammie vs the tohatsu, but the motors are rated at shaft hp at 5500 rpm in the prop.
I would love a comparison in the same boat by someone, see if the extra displacement and weight affects anything.
Take the yammie vs lighter tohatsu and Suzuki which both weigh under 100lbs in bare short shaft trim.
@@omieyouknowme Mmmmmmm....ya ,
The weight of the motor as to be consider, in this matter.
Yammie's are heavier to carry for & on, that same Boat in a speed test.
Ohhh ya ...Resistance is the name of that game.
Lighter Boat = heavy motor = Lighter Boat
Yamaha does have the power at 432 cc but any sort of resistance, is questionable.
As is the water spreading or the shape of the boat, is never gonna give us an answer.
I understand that 432cc as the power indeed, but i do have a SHAFT to consider.
hahahahahhhahahahahahha...........!!!
As for Connecting Rods on a motorcycle indeed.
I do have my F20 / 2021 on a 16 1/2 aluminium boat.
Having this 432cc is a good move,. Nevertheless if I want to consider using all of it,
Ill have to change the ECU and air diameter intake.
Tanks Man.
You make my day
@@JohnJohn-tf4cr I ran the f25 when it first came out, with just me after the motor warmed up it lost almost 500rpm. Yamaha would not believe me, so I made you tube videos.
Took the cowl off and had the extra 500rpm back. They eventually reflashed my ecu
I'm curious if run the motor first thing in morning, then at mid day when it's warm, do you lose rpm as well? My solution was I actually cut a hole in front of the intake, 3d printed a ram air snorkel for it. Of course sold the motor right after as I got a screaming deal on a 40hp.
What is the price for this motor? Please
I bought this as a package deal. So I dont know separate price
Hi ... i use the same motor on a rib boat 4.30.. on full speed i get just 24mph.. it looks ok or is slow?
Sounds just right
@@ACPro thanks 😉
Mine topped out at 26.. ua-cam.com/video/t6R5o7ta4I8/v-deo.html
What is the top speed of F20? What do u think? 23-24mph??
It depends on the boat but should hit 23
No kill switch attached?
Yes no way I would ever wear something like that. I don't drink bud light🤣
Water flush? How does that work?
Hook up your hose and flush it out.
Can I get power trim on a 15 short ???
I think you will have to buy a cmc aftermarket trim
Yamaha website says you can get one with power trim and tilt, and tilt-up feature, in the 15 inch shaft
Price
Not for sale
"I gotta have both" .... But I complain about how hard it is to tilt. Ever heard of tilt and trim?
Not on this small of motor. Pull forward on thw cowl and down on the handle for leverage.
no PFD on of course. and no lanyard connection to kill switch.
Those are for liberals .
Real men ain't scared.
wahhhh waahhhh pussy !!
Get a jack plate to avoid rocks
Good suggestion. Thank you
whats the weight of the boat?
300lbs just bare hull. So atleast 500plus rigged.
@@ACPro Full rigged one person on board what speed you get?
@@EDIPSOSTT it shows it in the video completely.
@@ACPro 500lbs including the outboard?
@@EDIPSOSTT no. Boat only
Mph? Or kmh
Mph
WHERE CAN I GET ONE ??
Any yamaha dealer should have them. Market place is good place to find used.
@@ACPro nobody in the state of colorado sells yamaha outboards really sad !
Oh and how many pounds is it??
135lbs
@@ACPro nice im really considering upgrading to a 4 stroke this season,, jus because of how old my mercury 2 stroke is, haha. The only thing holding me back is how heavy 4 strokes are,,,
Harganya berapa ya sampai indonesia...
Ph i would love to go to bali!!!
Oh.....saya di kaltim kab. Berau tempat objek wisata pulau derawan..
@@hijrah-wt2ul thank you 😊
suzuki all the way the best price and fueal ecinomy
Nothing wrong with a zuki!! I dont think fuel economy can even be compared on either of these small motors. They both sip fuel
For 25hp Yamaha’s a 2 cylinder, Suzuki’s is a 3 cylinder. Logic dictates that the Yamaha would be more fuel efficient.
DONT BUY YAMAHA 25HP FOUR STROKE FROM THE YEAR 02 TO 08 DONT BUY THESE MOTORS GO BAD AFTER A WHILE
28 KM/H isn't very fast for 19KW engine.
This is usa. We are on the standard system
That is miles per hour mph
@@ACPro OK, metric has been standard since about 1880. Not sure why you use imperial measurement still. You should state the speed in KM/H as normal so everyone understands. Good luck.
World is diffrent in different places . This is not a 19kw. It is 25hp. Like described. When you understand this you will be more diversified and have a wider knowledge of how the world works. There is 2 systems standard and metric. We use the standard however we are smart enough to know and recognize both. People also use different languages. We can recognize them too.
@@chippyjohn1 It makes sense for it to be mph cause he is from the us. But i still don’t understand why everybody use land units, i always use knots