Mike, Just wanted to say that your videos are extremely helpful! I just bought a 2007 Silver/grey base Saturn Sky, much like yours. I've been doing some mods and use your videos as a guide. Really helpful ! Keep up the great work.
HI Mike...sure enjoy your posts ... and helped with my mods after see yours... I also have a 07 Sky -- can you tell me how you replaced the reverse light and what size you bought to replace the old one Thanks again for the posts they are Great! Ted
Hi Mike, any chance you know how to replace a door lock mechanism? The tab on my drivers side door stopped popping up and won't lock/unlock anymore. My shop is quoting me $550 but i suspect this should be an easy repair. Any advice would be awesome!
Nice mod Mike. Think I'll do it myself. Re the placement of the resistors. That area can get pretty wet (it drains from a hole above the rear license plate), so hopefully the resistors are waterproof. I think they could be mounted a little higher to keep them from sitting in any water.
Yeah. I was thinking about that after I made the video. I am going to mount them up higher on the opposite side. I usually avoid the rain, but sometimes I get stuck in it by accident.
@@MikesHouseOfMods Did you move the location on these resistors? If so any chance you could post where you mounted them? I'm going to order these this week.
@@reignkinge Yes, I did move them. They're basically in the same position, but just up higher in that well area. I've gone through a few rain storms and haven't had any problems. I used the same 3M double tape as well and they're still holding strong.
@@MikesHouseOfMods Thanks Mike! I'm looking forward to doing this install (hopefully this coming weekend!). I'm pretty much just going to copy your work on this one.
I believe they have the LEDs on the bulb simulate a sweeping action when there's only one. If you look at the videos on their website, I think there are some single bulb examples.
I haven't yet. It's an LED light so unless the LEDs are messed up, there's no reason to change the light. But if you do need to get to it, here's a diagram and instructions on how to do it. It looks like you go from inside the trunk and push on two tabs. mikeshouseofmods.com/wp-content/uploads/2020/05/3rd-brake-light-1.jpg mikeshouseofmods.com/wp-content/uploads/2020/05/3rd-brake-light-2.jpg
Mike, Just wanted to say that your videos are extremely helpful! I just bought a 2007 Silver/grey base Saturn Sky, much like yours. I've been doing some mods and use your videos as a guide. Really helpful ! Keep up the great work.
I really like this project - I think I'll give it a try here shortly. Thanks for posting!
What when you've saved up enough money?
HI Mike...sure enjoy your posts ... and helped with my mods after see yours... I also have a 07 Sky
-- can you tell me how you replaced the reverse light and what size you bought to replace the old one
Thanks again for the posts they are Great!
Ted
Hi Mike, any chance you know how to replace a door lock mechanism? The tab on my drivers side door stopped popping up and won't lock/unlock anymore. My shop is quoting me $550 but i suspect this should be an easy repair. Any advice would be awesome!
Another cool video Mike!! I will get that for sure! Thanks for this one! Can you vary the speed of the sweep...
No. You cannot do that. But they do sweep for turn signals, hazards, braking, and even when you unlock the car with your key fob. Pretty cool.
Nice mod Mike. Think I'll do it myself. Re the placement of the resistors. That area can get pretty wet (it drains from a hole above the rear license plate), so hopefully the resistors are waterproof. I think they could be mounted a little higher to keep them from sitting in any water.
Yeah. I was thinking about that after I made the video. I am going to mount them up higher on the opposite side. I usually avoid the rain, but sometimes I get stuck in it by accident.
@@MikesHouseOfMods Did you move the location on these resistors? If so any chance you could post where you mounted them? I'm going to order these this week.
@@reignkinge Yes, I did move them. They're basically in the same position, but just up higher in that well area. I've gone through a few rain storms and haven't had any problems. I used the same 3M double tape as well and they're still holding strong.
@@MikesHouseOfMods Thanks Mike! I'm looking forward to doing this install (hopefully this coming weekend!). I'm pretty much just going to copy your work on this one.
@mike Martin - just finished this up. Thanks so much. Your video made this much easier than it would have been without.
Nice. I am assuming if the Solstice Only has one bulb, it WONT sweep like your does correct?
I believe they have the LEDs on the bulb simulate a sweeping action when there's only one. If you look at the videos on their website, I think there are some single bulb examples.
Thank you. I appreciate the response
Hi Mike. Question. Have you ever changed the center brake light? If so, you have a video or directions. Can’t figure out how to get at it. Thank you!!
I haven't yet. It's an LED light so unless the LEDs are messed up, there's no reason to change the light. But if you do need to get to it, here's a diagram and instructions on how to do it. It looks like you go from inside the trunk and push on two tabs. mikeshouseofmods.com/wp-content/uploads/2020/05/3rd-brake-light-1.jpg mikeshouseofmods.com/wp-content/uploads/2020/05/3rd-brake-light-2.jpg
Did you change the center brake light? How did you do it?
Hey mike
Love the mods
Ordered this yesterday
But when pushed add to cart went straight to PayPal site was very different
I checked it out and it's just a different way to pay via Paypal. It looked fine to me.
Neat, but I dislike how much dimmer they are than the stock lights.
Looks better than a mustang lol write this as you said it
That is one sketchy link.
The site looks pretty old, but it's legit.