i never had my trans slip or jerk at all on me. i had my brake caliper replaced and i felt the drag it was doing and i got to fix them. but as soon as my trans heats up it makes a whinning sound and i love forward and revers as well. what was the problem with ur mr
That answered my questions immediately. I've been through the ringer with my 2002 dodge 1500. Replaced the pressure control.. unit thing.. sorry, I'm tired.. lol. Man.. great video. Subscribed and liked.
I have a 2000 Jeep Cherokee with the AW4 transmission and just lost reverse at 263,000 hard hard miles "RHD postal vehicle", it goes into R and maybe puts 5% power to the wheels in R, but all 4 forward gears work perfect. The R slowly started slipping over the past 5,000 miles and is now down to 5% power. I got lucky and found a whole transmission with the transfer case out of a 00 Cherokee with 41,000 miles that had an engine fire. $400.... works perfect now. I want to pull my old AW4 apart to do an autopsy. I should note that the original AW4 had never been serviced once since new and the fluid was as thick as molasses and black. The AW4 is tough!!!
I have a fresh rebuild on a 76 turbo 350, it works in reverse, 1st and 2nd but does not seem to go from 2nd to drive, it just seems to rev. What could be the cause of that? I can pull out of park into reverse then nuetral and to drive and the car seems to move fine and shift thru from 1st to 2nd but not to drive. Any ideas of what to look for? I pulled the governor to see if it was stuck but was fine, replaced the new modulator with another new one and still the same.
I have a Toyota axio 2009, and for some reasons the Drive gear just stopped working. The car won't drive forward but can go on reverse. How can I fix it without necessarily replacing the whole transmission?
Excellent video! This is the fundamentals of diagnosing an automatic transmission. My 4l60E seems to not build pressure to move. I didn’t want to pull the transmission but I have no choice it seems because there is plenty of fluid, the truck sat for about two years before I got it, I’m guess something isn’t sealing to build pressure and drive, or something else? I’ll be making videos soon.
What happens if I fill only 6 quarts ( school bus requires 17 quarts ), and go D, R twice for 6.5ft ? Does that make front pump seal burns out and starts leaking fluid a few weeks later ?
What about shifting very hard into drive and reverse? 09 volvo xc90 v8 AWD, New engine installed and transmission fluid was changed out completely including torque converter. When it is shifted while on the vehicle lift with the drive shaft not installed the transmission shifts very hard into reverse and drive. Shift is so hard it shakes the vehicle on the lift lol what could that be? Transmission was fine before the new engine was installed and installation seemed to go very smooth no codes in TCM either
I have a mitsubishi pajero diesel with 4m40 engine, i went to test run it yesterday cause i just replaced my fuel pump a few minutes from my house it wouldn't accelerate or reverse.it starts well and does like it wants to move but wont i asked two mechanic and they have no clue do you think it could the the torque converter?. also today it makes a noise in park
I installed a new torque converter in a 4L60E transmission. It went in three times and fully seated but it still has wobble or play in it . Is that normal ?
I have a gran Grand Marquis and I have to let my transmission oil warm up let the car warm up and I just get on my motor a little bit and it automatically kicks in or when I drive some of the gears will slip I have to put it in drive and overdrive to order up to the state cape can but once I get it down the road it's driving normal but like if I come to a stop I have to bark it down and like two and then I'll bark it down to like one gear and it'll stay there and then when I get from the stop sign I get on up and bark it from one to two and back into drive and then it's normal
@codemansauto208 just had a question I have a 2004 GMC sierra 2500 drive and reverse, engage, barely moves 12 and three work and once I am at a higher speed on third gear, Drive works helped appreciated. Love your videos.
my 2005 toyota tundra v8 two wheel drive won't go forward or reverse and it also makes a weird noise no matter whatgear it's in and when I move my stearing wheel the noise gets louder and less louder depending on what direction I move my stearing wheel......does any body know what that's means or if you don't mind please help me out with my problem that I have with truck I been trying to fix my truck for like almost a whole year it's crazy I should of gotten it fixed already by know right
Had a performance rebuilt pt cruiser a604 with performance valve body. It was the billet torque converter going out. No reverse. Gear no forwards.. i checked axles had park and started in neutral..
Chrysler transmission was working perfectly fine and then while driving I hear a bang and its gone now, no gears at all. The transmission is whining, with increased rpms comes more whine. Any ideas? I'm thinking torque converter or pump? What do you think? how do I isolate the torque converter as the issue? Can I tell by just looking at the torque converter when I get the transmission off the car? Everything looks fine. from the outside, shifter cable good. differential all that stuff is good, something happened inside of the transmission.
My wife's Buick LeSabre 4T65E started jurking a little at first , then it stopped pulling completely. I let it cool down and it started pulling again. But after it got hot it stopped pulling again. So I was thinking it was the toque converter slipping or the stator Sprague slipping. Not really sure, but I took it to a transmission shop. I'm weighting to here from them. Being that the transmission shifts and pulls ok when cold and stopped pulling when hot I'm guessing it is a torque converter problem. When it first started I thought it was a ignition miss. I mean it really felt like a ignition coil or plug wire shorting out.
sounds like your on the right track with the torque converter but usually when the converters goes bad they have little pieces of metal that stop the filter up and thats whats probably stopping the car from pulling the bad part about this is it may require a rebuild to remove all the metal debris, i hope this helped you
I have an A4LD in a Mustang that upon cold startup, it goes into any gear properly but has almost no pull. As it warms up though, the pull gets stronger until operating temp has been achieved. It pulls normally then. The fluid level is where it should be.
My truck doesn’t drive when it’s on Drive Gear ⚙️ something seems like it’s stuck. But the other gears are completely fine. I’m not sure what it could be , considering I just recently got my differential fixed the idiots made a leak in it so I’m guessing that it messed up the transmission
I have a 06 Chevy Colorado with a 4L60e transmission and it goes into " drive" but just revs up and doesn't go anywhere but reverse and the gear "1-2" work and drives am I in need of a new transmission???
My car doesn’t find any gears all of a sudden, no warning it was shifting fine and smooth until it just disappeared on me. I see the shifter cable moving the black plastic thing on the Tran. But it doesn’t even try to find anything what happened? 2004 ford taurus SE
I have a Lexus is200..Reverse is not pulling or engaging. My mechanic told me I will have to replace my transmission but I need a second opinion. Any advice
I have a 07 Silverado 2500 HD 6l90 2wd I do believe . Parked the park next day went to leave and it doesn’t move even in neutral it’s acting like it’s still in park . When you shift to drive or reverse it sounds like it idles down but it’s still locked up
What if I lost forward and reverse, heard a whirling noise. Adjusted fluid level, still no forward or reverse (Was low, not on dip stick) Few days later drives fine? Is trapped air a thing?
Why would a 2007 GMC Sierra I was going down the road and all the sudden it felt like a standard that has slipped out of gear and now it won't go forward I have no forward gears but I have a good reverse
My car nissan tiida 2007 non cvt gearbox repaired last week . Now gearbox is work fine but in high slope or in hill car roll down very fast if break released so difficult to accelerate . Please help me what is the reason . It dose not have hill start assistant in this model . Please help
Excellent video. I have a 96 Civic. One day on my way back from work my transmission stops working won't go in any gear not forward not reverse. I had the car towed to my house. Next morning I started the car and tried to move the car and it worked fine. I drove around the block but as soon I came back into my driveway it stopped working again. I checked again next morning it worked only when the engine is cold and as soon as the engine gets hot the transmission stops working at all. In your opinion what do you think is going on with my transmission? I hope to hear from you soon. Thanks
@@THESMOOVEGAMER no not yet. But, I am going to change the speed sensor and hopefully that will solve the issue because I watched a video and in that video the guy had the same problem. Keep me in your prayers.
Hey i really didnt understood one with the “wont drive forward but reverse works fine” i have the same problem with my audi s6 C5 4.2, i bought a new torque converter but i havent installed it yet, so is it the torque converter? Or the gears?
Hi sir, I have a 1999 Ford F250 Super Duty 4WD 7.3 Power Stroke, The torque converter is beeping and at the time of gear 1 and 2 it would stick and at 3000 rpm I would shift and it would knock,So I decided to replace the torque converter, and when I turn it on, the truck doesn't work in the front, nor in the rear.Is it possible that the torque converter was defective or the installation was poor?Thank you very much, I hope for your help.
2005 trailblazer 4l60e . Would not shit out of first. Dropped pan, replaced pillow switch. Pan back on .fresh fluid. Also replaced speed censor at back of yolk. This is a 4wheel drive trans. After I was done with correct fluid level, no forward or reverse. (Yes cable is hooked up. Any feed back would be appreciated
@@codemansauto208 thank you for your reply. I should have stated I have zero gears working. It's like the trany isn't even there. Just got back from vacation I'll check all relatable fuses.
Thanks Codemans for sharing youre expertise . ive got an05 honda civic stock , that pretty much went to neutral at 60 mph . towed it home then it only goes back or forward for about 5 seconds , upon first start up , does have a little whinning noise . could that be a bad torque converter ? thx .
@@codemansauto208 I have an 1977 international scout with the 727 automatic trans. I put it on drive and it slowly accelerates. But no reverse. What can the issue be?
When I was younger, we would hear about a friend who had blown a tranny, back then you could safely assume the conversation was referring to automobile's
@@productions6994 Agreed. Used to be something that would shift gears. Now it could be someone with their gears shifted. It's a Confusing world.🤔😏 A man needs an ASE PHD just to make sence of it all. I hope you appreciate that last one, as it just came to me. We may be the only 2 humans who know that joke. Lol
@@Thesaurcery4U2C 🤣🤣🤣🤣 my friend you sound like you would be an awesome man to have a few beers with or twelve lol!!!! So happy to see there is still like minded people in this world and I'm not going crazy!!!!! Straight pride!!!!!!
Hi I have a 95 dodge b2500 5.9 V8 46RH. When I put it in drive it won't move just revs up and acts like it wants to drive but doesn't, but I can manually put it in 1st, 2nd and into drive and it works fine. But when I come to a stop I have to put it back into first and back to second and into drive. Reverse works fine as well. Any ideas? I would appreciate it, thanks I subscribed.
I know this is a older post but got a question. My car was driving fine, I had to WOT to go across traffic, then I had nothing ...came to a stop and it rolls in Park, when I shift the gears, I can feel it like shift but nothing. When I put it in Park, it grinds so I stop the engine to park it, but like I stated, I can push roll in all gears including park...thoughts?
You give me the impression to be a very honest man. saying that , I have a very important question regarding my Baby, a 1960 Impala. I'm an 79 year old man with cancer. and I will like to sell my classic before I past, I have being all my life mechanically incline , but I need your expert advice.,I keep my car all ways in a running condition but only in my garage ,never on the road, I moved it occasionally , this time I was working on the my car with the 4 tires on the air (on stands ) when a friend start the engine and abruptly move the gearshift ,and hear a bad grinding noise, after that the transmission don't go forward only reverse , can you tell me what might be the problem, Thank You and God bless.
could find answer to my problem tho. :( my transmission work great, but starts pulling the second it goes in freewheeling, (rolling without power from the engine) then I need to restart the car to get the transmission working again. sooo strange to me, cant understand. happened suddenly.
What do you think if it lurches foward a tiny bit in park..nothing in reverse and drives in nutrual and all other gears..I have a 700r4 that had the guts installed in a new casing?
I have a ZF6HP that won't move when it's in drive or reverse but when I put her in neutral I can move it forward at about 3000RPM although it obviously doesn't pull like it should...If I crawl in neutral the second I shift into drive it comes to a halt...It's not the shift mechanism because the mechanical position matches what the scan tool says the computer is getting. Any ideas? It definitely shouldn't move in neutral though right?
I have a 2009 Silverado 1500 with the 6L80. It stopped pulling was making a whining noise and now noise is gone and it's pulling again. Any ideas on what's happening?
thats a tough one for the 6l80 making noises but sometime the noise could be the torque converter or pump making the noise, check out my other video on a 6l80 with a cracked filter, this has been a problem from the factory hope this helps
I have a 1991 Ford Ranger 2wd that sat for years and replaced all fluids and filters including the trans fluid and filter and as I was bleeding the coolant system my trans fluid started to leak a good bit of transmission fluid, and I noticed a wire hanging by the transmission I’ve never seen that before when I was changing the trans filter and everything. Any info helps thanks!
if the fluid level drops when you start the truck then your pump is working, and if the pump is working then you could have a problem in the input shaft area
i have a 2010 4.0 ford mustang that will not move. i’ve replaced the fluid and filter, even replaced the whole transmission. my dad has done everything he knows to do and has done it all by himself. would love to hear your opinion, thanks.
I got a Chevy Silverado 2005 whenever I try to put it in reverse it wont move but it’ll make like a grinding noise but if I put on 4 wheel drive it does reverse what could it be?
@@codemansauto208 I have an 08 tbss. So I have a TBSS 08 that won’t crank over. It was in the shop getting the suspension swapped to coils and after it got out the shop no more than three days later it completely shitted on me in traffic. It wouldn’t go foward anymore just backwards. That was a few months ago. It will turn on but won’t start. Do y’all think I need a whole new engine or will a new transmission fixed my problem? 
My truck was being towed but it was in drive gear instead of neutral now it won’t go foward or reverse. Any ideas on what’s wrong? It’s a 2014 Silverado 1500 4x4
make sure that the tow truck driver didn't put your transfer case in neutral If your transfer case is in neutral you will have a noise going from drive to park
hello , im not sure if you are still available or accepting any questions , I have 03 ranger xlt 2wd , i lost reverse and drive on my way to work as if it was in neutral , only 1st n 2nd , OD doesnt work either do you think this could be the OD sprag ?
My Chrysler grand voyager 2010 2.8 CRD vehicle engine starts ok and rev up but car isn’t moving in both forward or reverse. Mechanic tried replacing transmission fluid and filter but no luck. It’s only moving an inch forward or backward nothing more. He now saying I need a torque converter but he’s not guaranteed whether that solves the problem 😢 can you please provide your inputs what could be wrong?
your torque converter can cause this issue but if he cant guarantee that it will fix it then i would take to someone who is more sure that he knows what the problem is
I have an 1977 international scout with 727 auto transmission. I put it in drive and it slowly accelerates when gassing it. And in reverse it won’t move at all. What can the issue be there?
I have an 02 Silverado 4l60e that only shifts into both drive and reverse only when u start it wether it's at operating temp or not then after a few shifts from drive to reverse there's nothing? I turn the truck off them start it and does the same thing shifts fine then nothing. I went through all the comments hoping to not ask again if it had been answered but didn't find anything, any info would help 🤷🏽♂️
if you are losing all gears then it must be either the torque converter is bad or something is coming apart and it is stopping up your filter make sure the fluid level is good because chevy is known for one side of the stick showing full and the other showing nothing always go by the lowest fluid on the stick
the 2008 Pathfinder is known for having issues with the transmission fluid and antifreeze cross mixing in the radiator, make sure this isnt happening to you and if it is you should change the fluid and replace the radiator ASAP The actions that you explained on your pathfinder make me think this maybe happening to yours
I have a 05 sprinter only goes into gear in 10 seconds of starting the engine after driving 5min in first gear it won't pull at all and I have to turn off the engine for a minute to do it again to make it move, is that because of a bad torque converter
this sounds like a bad torque converter, thats exactly what a failing torque converter action is getting by with just replacing the torque converter is a possibility with this type transmission i would pull the pan and inspect the fluid for metal and determine from there if just a torque converter is needed
My transmission won't move in reverse or drive. You said something about when putting it in park it makes a grinding noise? Mine does that. What is the problem then?
if its a front wheel drive then check for a broken axle if its a rear wheel drive possible transfer case or rear diff also you could put it in park and see if you can shove the vehicle if it is a broke axle the vehicle will roll in park
I have Golf MK1 Automatic it only goes reverse no more forward, now someone advice me to look for Torgue Converter. Now I'm looking for Golf 1 Torque Converter, please help out.
My truck is 1988 GMC Sierra K2500. It sometimes pulls, in Reverse and Drive but then after driving it for about 5 minutes it looses all gears, no drive no reverse. And sometimes when I start it, it just won't engage in D and R. What do you think that could be?
it sounds like there may be something coming apart inside the transmission and it could be clogging up the filter? but i dont think a filter change will solve all of those issues
i have a 1995 f150 automatic 5.0 it drives forward perfectly fine no issues but when i put it into reverse it like shakes the whole car and it wont move into reverse at all i dont know what to do or how to fix it please help
got a 1990 Nissa D21 Hard-body pickup truck 2WD with a 4 cylinder automatic transmission. I got something wrong with the transmission are something. Let me begin at the beginning. I had the fuel pump go out why I was going to work and had to get towed 80 miles back home. And While I was being towed I had the truck in Neutral and didn't think nothing of it and keep being towed. But for the first 10 miles of being towed with the engine turned off. it still sounded like the engine was running. then all of a sudden the back tires locked up briefly for a tenth of a second then it didn't sound like the truck was running anymore. Then when I got home i changed the fuel pump and got the truck started I put it into reverse backed out of my driveway then put it into drive but their was no forward gears only reverse can anybody please put me in the right direction and tell me what I screwed up and what I need to change. I now know you supposed to unhook the driveshaft it you have an automatic and are being towed more then 10 are 15 miles
My truck is a 1977 chevy 350 engine automatic transmission 4 wheel drive but has no gears at all it sounds like it's shifting but does nothing and I replaced the rear end fluid still nothing
I have a 2000 ford f250 7.3 powerstroke an I was driving in 2nd an put in back in to drive an heard a clunk an now I don't have any gears what could that be
I have a 2001 GMC Sierra with a 4l60e. One day my truck suddenly acted like it was in neutral. All gears are like neutral but park still works. I replaced the fluid pump and it’s still doing the same thing. Any suggestions would be greatly appreciated.
@@ronniecox109 so I figured out that I didn’t seat the torque converter right when I put the transmission back in and broke the new pump. I now got a new pump (again) and it’s back in but I have no second or fourth gear. I was told that it’s either the servo or the band. I changed the servo and no change. I don’t know anything about the band. Like what position it’s supposed to be on or anything like that.
Shift solenoid A. is on in 2nd And 4th. Should show a code. OR if this is a used unit, The band applies on the reverse drum in 2 and 4 , a dished rev drum will result in no 2 or 4(OD). Or a servo apply valve ,stuck open In the valve body.
Try to put it in manual low, if it goes thru the gears when you manual upshift then its your one way sprag but if it doesn't move then it could be burnt clutches
-make sure the drive shaft is not turning while in drive gear. -if it turns then your rear dif may be broke - if its a four by four put in four wheel low lock and see if it will pull- that will rule out the transfer case
So I have a question, my truck transmission has always worked fine and all of a sudden today I put it in drive and couldn't feel it go into gear so I gave it some throttle and it takes a second and then it moves , what could be the issue?
@@carlosv5117 the automatic transmission had 370000 miles on it plus the previous owner drove it into a lake, so it had to have had water damage, truck is absolutely beautiful, but the motor was blown because of the water so put a motor in that only has 128000 miles on it, runs beautiful, and my 7f5 I just converted it to is a beast. So now the truck is badass.
My Saturn Ion 2006 lost all forward 2 weeks ago. The so-called expert at Aamco said tranny has bad clutch and priced the job at $1700.00. Couldn't afford it so had car towed home. Did some google research and found out that these Ion's have an issue with a feed pipe that is located under the transmission pan. The pipe breaks at the weld and usually car will only lose forward gear. Took a chance and ordered the feed pipe from Amazon for $124.00 and sure enough the pipe was broken off at the weld. Slapped in the new pipe and car runs perfect again. Sadly, we can't always trust the word of the so-called experts. Here's the how-to video of the broken feed pipe. ua-cam.com/video/jW9h-9TEOn0/v-deo.html
you did your homework and that's awesome! that's what I like about youtube it keeps mechanics honest! I already have a video about this tube but it is Titled under Cobalt and HHR I didn't add Saturn because Saturn put a CVT transmission in some of their cars and I was trying to keep from confusing anyone
I have a a500 no forward or reverse. I will check the things out you mention. Great advice. Thanks
i never had my trans slip or jerk at all on me. i had my brake caliper replaced and i felt the drag it was doing and i got to fix them. but as soon as my trans heats up it makes a whinning sound and i love forward and revers as well. what was the problem with ur mr
*RECOMMEND YOU WATCH THIS*
Best informative video I've seen yet and I have viewed hours of videos on this subject
Thank you sir. Exactly what I was looking for.
I have been trying to diagnose trans problem in a RE4R01A without going too deep Into it. Thankyou!!!
Thanks for educating me
Very Clear, Simple, and Informative. Good to know I might not be set back another 7k by a truck i already overpaid for lol.
Thank You for sharing your knowledge 🙏
That answered my questions immediately.
I've been through the ringer with my 2002 dodge 1500.
Replaced the pressure control.. unit thing.. sorry, I'm tired.. lol.
Man.. great video. Subscribed and liked.
I have a 2000 Jeep Cherokee with the AW4 transmission and just lost reverse at 263,000 hard hard miles "RHD postal vehicle", it goes into R and maybe puts 5% power to the wheels in R, but all 4 forward gears work perfect. The R slowly started slipping over the past 5,000 miles and is now down to 5% power. I got lucky and found a whole transmission with the transfer case out of a 00 Cherokee with 41,000 miles that had an engine fire. $400.... works perfect now. I want to pull my old AW4 apart to do an autopsy. I should note that the original AW4 had never been serviced once since new and the fluid was as thick as molasses and black. The AW4 is tough!!!
Let me know if you end up figuring out what happened?
@@baileymccoist3694 thank you... the autopsy will come once the weather warms up like in May...
I'm sure I'll find something... I'll update...
Thank you for the information 👍🏼
this video does help out alot too thanks
Finally someone talking my language. Thanks
I have a fresh rebuild on a 76 turbo 350, it works in reverse, 1st and 2nd but does not seem to go from 2nd to drive, it just seems to rev. What could be the cause of that? I can pull out of park into reverse then nuetral and to drive and the car seems to move fine and shift thru from 1st to 2nd but not to drive.
Any ideas of what to look for? I pulled the governor to see if it was stuck but was fine, replaced the new modulator with another new one and still the same.
Good input !
Thank you for sharing your knowledge.
Great video 👍👍
I have a Toyota axio 2009, and for some reasons the Drive gear just stopped working. The car won't drive forward but can go on reverse. How can I fix it without necessarily replacing the whole transmission?
Hi, my Isuzu wizard "4JG2" auto transmission does not move forward but can reverse.
Please help me solve this problem.
Thanks.
Jp
Excellent video! This is the fundamentals of diagnosing an automatic transmission. My 4l60E seems to not build pressure to move. I didn’t want to pull the transmission but I have no choice it seems because there is plenty of fluid, the truck sat for about two years before I got it, I’m guess something isn’t sealing to build pressure and drive, or something else? I’ll be making videos soon.
How'd it go? My truck won't go in drive or reverse. Only works in 1st and 2nd gear. Thinking it's the overdrive band...
@@Norcaljourneyman my pump is damaged
@@Norcaljourneyman same problem here on a ranger please lmk!!
@@Norcaljourneyman I’m on the same boat did you ever know what happened?
What happens if I fill only 6 quarts ( school bus requires 17 quarts ), and go D, R twice for 6.5ft ? Does that make front pump seal burns out and starts leaking fluid a few weeks later ?
Great video 💪🏾
What about shifting very hard into drive and reverse? 09 volvo xc90 v8 AWD, New engine installed and transmission fluid was changed out completely including torque converter. When it is shifted while on the vehicle lift with the drive shaft not installed the transmission shifts very hard into reverse and drive. Shift is so hard it shakes the vehicle on the lift lol what could that be? Transmission was fine before the new engine was installed and installation seemed to go very smooth no codes in TCM either
Great video, new sub
I have a mitsubishi pajero diesel with 4m40 engine, i went to test run it yesterday cause i just replaced my fuel pump a few minutes from my house it wouldn't accelerate or reverse.it starts well and does like it wants to move but wont i asked two mechanic and they have no clue do you think it could the the torque converter?. also today it makes a noise in park
I installed a new torque converter in a 4L60E transmission. It went in three times and fully seated but it still has wobble or play in it .
Is that normal ?
I have a gran Grand Marquis and I have to let my transmission oil warm up let the car warm up and I just get on my motor a little bit and it automatically kicks in or when I drive some of the gears will slip I have to put it in drive and overdrive to order up to the state cape can but once I get it down the road it's driving normal but like if I come to a stop I have to bark it down and like two and then I'll bark it down to like one gear and it'll stay there and then when I get from the stop sign I get on up and bark it from one to two and back into drive and then it's normal
I got a 1996 Mitsubishi gallant the tourk converter automatic transmission it goes in reverse but will stall going forward
@codemansauto208 just had a question I have a 2004 GMC sierra 2500 drive and reverse, engage, barely moves 12 and three work and once I am at a higher speed on third gear, Drive works helped appreciated. Love your videos.
my 2005 toyota tundra v8 two wheel drive won't go forward or reverse and it also makes a weird noise no matter whatgear it's in and when I move my stearing wheel the noise gets louder and less louder depending on what direction I move my stearing wheel......does any body know what that's means or if you don't mind please help me out with my problem that I have with truck I been trying to fix my truck for like almost a whole year it's crazy I should of gotten it fixed already by know right
Had a performance rebuilt pt cruiser a604 with performance valve body. It was the billet torque converter going out. No reverse. Gear no forwards.. i checked axles had park and started in neutral..
Chrysler transmission was working perfectly fine and then while driving I hear a bang and its gone now, no gears at all. The transmission is whining, with increased rpms comes more whine. Any ideas? I'm thinking torque converter or pump? What do you think? how do I isolate the torque converter as the issue? Can I tell by just looking at the torque converter when I get the transmission off the car? Everything looks fine. from the outside, shifter cable good. differential all that stuff is good, something happened inside of the transmission.
My wife's Buick LeSabre 4T65E started jurking a little at first , then it stopped pulling completely. I let it cool down and it started pulling again. But after it got hot it stopped pulling again. So I was thinking it was the toque converter slipping or the stator Sprague slipping. Not really sure, but I took it to a transmission shop. I'm weighting to here from them.
Being that the transmission shifts and pulls ok when cold and stopped pulling when hot I'm guessing it is a torque converter problem.
When it first started I thought it was a ignition miss. I mean it really felt like a ignition coil or plug wire shorting out.
sounds like your on the right track with the torque converter but usually when the converters goes bad they have little pieces of metal that stop the filter up and thats whats probably stopping the car from pulling
the bad part about this is it may require a rebuild to remove all the metal debris, i hope this helped you
I have an A4LD in a Mustang that upon cold startup, it goes into any gear properly but has almost no pull. As it warms up though, the pull gets stronger until operating temp has been achieved. It pulls normally then. The fluid level is where it should be.
Hard rubber seals in the drum, old timers called it morning sickness.typical ford problem.
My truck doesn’t drive when it’s on Drive Gear ⚙️ something seems like it’s stuck. But the other gears are completely fine. I’m not sure what it could be , considering I just recently got my differential fixed the idiots made a leak in it so I’m guessing that it messed up the transmission
I have a 06 Chevy Colorado with a 4L60e transmission and it goes into " drive" but just revs up and doesn't go anywhere but reverse and the gear "1-2" work and drives am I in need of a new transmission???
I have nissan pathfinder 2nd generation 2005 3.5 engin I have lost my revers there no mechanic in my area what should I check
My car doesn’t find any gears all of a sudden, no warning it was shifting fine and smooth until it just disappeared on me. I see the shifter cable moving the black plastic thing on the Tran. But it doesn’t even try to find anything what happened? 2004 ford taurus SE
I have a Lexus is200..Reverse is not pulling or engaging. My mechanic told me I will have to replace my transmission but I need a second opinion. Any advice
I have a 07 Silverado 2500 HD 6l90 2wd I do believe . Parked the park next day went to leave and it doesn’t move even in neutral it’s acting like it’s still in park . When you shift to drive or reverse it sounds like it idles down but it’s still locked up
What if I lost forward and reverse, heard a whirling noise. Adjusted fluid level, still no forward or reverse (Was low, not on dip stick) Few days later drives fine? Is trapped air a thing?
Why would a 2007 GMC Sierra
I was going down the road and all the sudden it felt like a standard that has slipped out of gear and now it won't go forward I have no forward gears but I have a good reverse
my civic 01 AT no drive no reverse, scanned but no fault code. it starts, it has NO checkengine..ATF full..what do u think the problem?
i need help i got a nissan terrano 1997 td27t not moving forward or reverse
Will the car out stall out an not want to start up like it's out of gas or not want to start up again like bad fuel pump or starter
I just purchased a 2012 nissan juke,i did notice my axels are leaking can that cause no reverse ?
i have a 1987 350 700r square body chevy, it has reverse but not drive. obviously transmission but what could it be inside going on?
07 Chevy express van
Drives forward good
Reverse takes increase idle to go,
Any thoughts thx
My ES 330 LEXUS CANT MOVE. Transmissions not reading. What might be the problem?
What would make one after it changed out of frist and 2and it go in to 3 it seems like it in N
My car nissan tiida 2007 non cvt gearbox repaired last week . Now gearbox is work fine but in high slope or in hill car roll down very fast if break released so difficult to accelerate . Please help me what is the reason . It dose not have hill start assistant in this model . Please help
Excellent video. I have a 96 Civic. One day on my way back from work my transmission stops working won't go in any gear not forward not reverse. I had the car towed to my house. Next morning I started the car and tried to move the car and it worked fine. I drove around the block but as soon I came back into my driveway it stopped working again. I checked again next morning it worked only when the engine is cold and as soon as the engine gets hot the transmission stops working at all. In your opinion what do you think is going on with my transmission? I hope to hear from you soon. Thanks
Have you found the issue ?
@@THESMOOVEGAMER no not yet. But, I am going to change the speed sensor and hopefully that will solve the issue because I watched a video and in that video the guy had the same problem. Keep me in your prayers.
@@hilifetravel8764 found the problem?
@@f.b.i8015 yes. It was speed sensor.
丿丨丨丨一？一丨丿丨丿？？卅丶丨丨？丿丿一丨丿丨？丨丨丿一丿？丿一丨丨丨？？丨丿一丨丨？丨丨丿丨？？丨一丿丿？？做？丿一一丨丿一丨丿？一丨丿丨丨？？丨丿丨丿？三？丨丿丨一？一丨一丿丨丿一一？丿丿丿丨一一？一丨丿丨丿？丨丨一？丨丨一？花？一丿丨一丿？一丿丨一丨丨？？？？？？丿一丨丿丿？？在？？栞？？一丨一丨一丨一一？一丿丿一一一？
Hey i really didnt understood one with the “wont drive forward but reverse works fine” i have the same problem with my audi s6 C5 4.2, i bought a new torque converter but i havent installed it yet, so is it the torque converter? Or the gears?
gears most likely
Hi sir, I have a 1999 Ford F250 Super Duty 4WD 7.3 Power Stroke, The torque converter is beeping and at the time of gear 1 and 2 it would stick and at 3000 rpm I would shift and it would knock,So I decided to replace the torque converter, and when I turn it on, the truck doesn't work in the front, nor in the rear.Is it possible that the torque converter was defective or the installation was poor?Thank you very much, I hope for your help.
2005 trailblazer 4l60e . Would not shit out of first. Dropped pan, replaced pillow switch. Pan back on .fresh fluid. Also replaced speed censor at back of yolk. This is a 4wheel drive trans. After I was done with correct fluid level, no forward or reverse. (Yes cable is hooked up. Any feed back would be appreciated
check your fuse, if its blown it will make it take off in 2nd gear and you will loose 1st and fourth
@@codemansauto208 thank you for your reply. I should have stated I have zero gears working. It's like the trany isn't even there. Just got back from vacation I'll check all relatable fuses.
@@jeffgordon9103 did you find the problem?
I have no forward gears but i have reverse what do you think it can be.
Thanks Codemans for sharing youre expertise . ive got an05 honda civic stock , that pretty much went to neutral at 60 mph . towed it home then it only goes back or forward for about 5 seconds , upon first start up , does have a little whinning noise . could that be a bad torque converter ? thx .
yes it could be and with the systems you are experiencing replacing the torque converter could be the fix
@@codemansauto208 I have an 1977 international scout with the 727 automatic trans. I put it on drive and it slowly accelerates. But no reverse. What can the issue be?
My 2012 savvana van wont pull forward or reverse also when this happens the abs and emergency brake light came on
When I was younger, we would hear about a friend who had blown a tranny,
back then you could safely assume the conversation was referring to automobile's
Good ole days when Democrats werent tryna make everyone gay, take our guns, and dress kids In dragg......
@@productions6994
Agreed.
Used to be something that would shift gears.
Now it could be someone with their gears shifted.
It's a Confusing world.🤔😏
A man needs an ASE PHD just to make sence of it all.
I hope you appreciate that last one, as it just came to me.
We may be the only 2 humans who know that joke. Lol
@@Thesaurcery4U2C 🤣🤣🤣🤣 my friend you sound like you would be an awesome man to have a few beers with or twelve lol!!!! So happy to see there is still like minded people in this world and I'm not going crazy!!!!! Straight pride!!!!!!
My rear diff went out and now it wont mive with a new one no gears will get it ti mive like no power going through
Hi I have a 95 dodge b2500 5.9 V8 46RH. When I put it in drive it won't move just revs up and acts like it wants to drive but doesn't, but I can manually put it in 1st, 2nd and into drive and it works fine. But when I come to a stop I have to put it back into first and back to second and into drive. Reverse works fine as well. Any ideas? I would appreciate it, thanks I subscribed.
I know this is a older post but got a question. My car was driving fine, I had to WOT to go across traffic, then I had nothing ...came to a stop and it rolls in Park, when I shift the gears, I can feel it like shift but nothing. When I put it in Park, it grinds so I stop the engine to park it, but like I stated, I can push roll in all gears including park...thoughts?
It sounds like a broken axle I would check there first Hope this helps you
You give me the impression to be a very honest man. saying that , I have a very important question regarding my Baby, a 1960 Impala. I'm an 79 year old man with cancer. and I will like to sell my classic before I past, I have being all my life mechanically incline , but I need your expert advice.,I keep my car all ways in a running condition but only in my garage ,never on the road, I moved it occasionally , this time I was working on the my car with the 4 tires on the air (on stands ) when a friend start the engine and abruptly move the gearshift ,and hear a bad grinding noise, after that the transmission don't go forward only reverse , can you tell me what might be the problem, Thank You and God bless.
could find answer to my problem tho. :( my transmission work great, but starts pulling the second it goes in freewheeling, (rolling without power from the engine) then I need to restart the car to get the transmission working again. sooo strange to me, cant understand. happened suddenly.
My truck wont even manually go into reverse or park but has all other gears. Also cuts out when I try to pull weight in 4x4 reverse.
I have also same problem
What do you think if it lurches foward a tiny bit in park..nothing in reverse and drives in nutrual and all other gears..I have a 700r4 that had the guts installed in a new casing?
something is binding up in the transmission, possibly forward clutch pack built with not enough clearance
I have a ZF6HP that won't move when it's in drive or reverse but when I put her in neutral I can move it forward at about 3000RPM although it obviously doesn't pull like it should...If I crawl in neutral the second I shift into drive it comes to a halt...It's not the shift mechanism because the mechanical position matches what the scan tool says the computer is getting.
Any ideas?
It definitely shouldn't move in neutral though right?
Forward frictions are partially welded together,
I have a 2009 Silverado 1500 with the 6L80. It stopped pulling was making a whining noise and now noise is gone and it's pulling again. Any ideas on what's happening?
thats a tough one for the 6l80 making noises but sometime the noise could be the torque converter or pump making the noise, check out my other video on a 6l80 with a cracked filter, this has been a problem from the factory
hope this helps
Mine is a Lexus GS300 2006 with few seconds delay in engaging reverse. what could possibly be the problem?
Thank you Sir
First time I understand from your experiences
What actually we all should be looking at
Help people sharing your experiences
I have a 1991 Ford Ranger 2wd that sat for years and replaced all fluids and filters including the trans fluid and filter and as I was bleeding the coolant system my trans fluid started to leak a good bit of transmission fluid, and I noticed a wire hanging by the transmission I’ve never seen that before when I was changing the trans filter and everything. Any info helps thanks!
Its a auto transmission and It won’t go into any gear, it doesn’t make any noise when trying to go in Reverse or Drive or Overdrive
if the fluid level drops when you start the truck then your pump is working, and if the pump is working then you could have a problem in the input shaft area
i have a 2010 4.0 ford mustang that will not move. i’ve replaced the fluid and filter, even replaced the whole transmission. my dad has done everything he knows to do and has done it all by himself. would love to hear your opinion, thanks.
does it make noise when you go from drive to park ?
Mines does what’s that mean and this was sudden it wasn’t giving me any warnings
I got a Chevy Silverado 2005 whenever I try to put it in reverse it wont move but it’ll make like a grinding noise but if I put on 4 wheel drive it does reverse what could it be?
My gmc awd does the same it doesn’t move in any gear but it makes a grinding noise I can’t find anyone to help
I have a 09 Dodge Charger and I’ve lost both reverse and drive but you can feel it engage when you put it in reverse and in drive but it will not move
does it make a noise when you put it in park
@@codemansauto208 I have an 08 tbss. So I have a TBSS 08 that won’t crank over. It was in the shop getting the suspension swapped to coils and after it got out the shop no more than three days later it completely shitted on me in traffic. It wouldn’t go foward anymore just backwards. That was a few months ago. It will turn on but won’t start. Do y’all think I need a whole new engine or will a new transmission fixed my problem? 
@@codemansauto208 no
I was driving and suddenly my car wouldn't go in drive or reverse but I was able to park and go in neutral other that idk
My truck was being towed but it was in drive gear instead of neutral now it won’t go foward or reverse. Any ideas on what’s wrong? It’s a 2014 Silverado 1500 4x4
make sure that the tow truck driver didn't put your transfer case in neutral
If your transfer case is in neutral you will have a noise going from drive to park
hello , im not sure if you are still available or accepting any questions , I have 03 ranger xlt 2wd , i lost reverse and drive on my way to work as if it was in neutral , only 1st n 2nd , OD doesnt work either do you think this could be the OD sprag ?
it is a possibility with no forward and drive range then the sprag could possibly be broke
My Chrysler grand voyager 2010 2.8 CRD vehicle engine starts ok and rev up but car isn’t moving in both forward or reverse. Mechanic tried replacing transmission fluid and filter but no luck. It’s only moving an inch forward or backward nothing more. He now saying I need a torque converter but he’s not guaranteed whether that solves the problem 😢 can you please provide your inputs what could be wrong?
your torque converter can cause this issue but if he cant guarantee that it will fix it then i would take to someone who is more sure that he knows what the problem is
I have an 1977 international scout with 727 auto transmission. I put it in drive and it slowly accelerates when gassing it. And in reverse it won’t move at all. What can the issue be there?
the reverse band has to release in drive and it has to apply while in reverse so I would look in the apply servo area
I have an 02 Silverado 4l60e that only shifts into both drive and reverse only when u start it wether it's at operating temp or not then after a few shifts from drive to reverse there's nothing? I turn the truck off them start it and does the same thing shifts fine then nothing. I went through all the comments hoping to not ask again if it had been answered but didn't find anything, any info would help 🤷🏽♂️
if you are losing all gears then it must be either the torque converter is bad or something is coming apart and it is stopping up your filter
make sure the fluid level is good because chevy is known for one side of the stick showing full and the other showing nothing
always go by the lowest fluid on the stick
@@codemansauto208 thank you!
I have a 2008 pathfinder just out of no where when warms up i loose all gear dosnt seem like slip they just go away possible torque converter?
the 2008 Pathfinder is known for having issues with the transmission fluid and antifreeze cross mixing in the radiator, make sure this isnt happening to you and if it is you should change the fluid and replace the radiator ASAP
The actions that you explained on your pathfinder make me think this maybe happening to yours
I have a 05 sprinter only goes into gear in 10 seconds of starting the engine after driving 5min in first gear it won't pull at all and I have to turn off the engine for a minute to do it again to make it move, is that because of a bad torque converter
this sounds like a bad torque converter, thats exactly what a failing torque converter action is
getting by with just replacing the torque converter is a possibility with this type transmission
i would pull the pan and inspect the fluid for metal and determine from there if just a torque converter is needed
My transmission won't move in reverse or drive. You said something about when putting it in park it makes a grinding noise? Mine does that. What is the problem then?
if its a front wheel drive then check for a broken axle
if its a rear wheel drive possible transfer case or rear diff
also you could put it in park and see if you can shove the vehicle if it is a broke axle the vehicle will roll in park
I have Golf MK1 Automatic it only goes reverse no more forward, now someone advice me to look for Torgue Converter.
Now I'm looking for Golf 1 Torque Converter, please help out.
Flip the seat around.
My truck is 1988 GMC Sierra K2500. It sometimes pulls, in Reverse and Drive but then after driving it for about 5 minutes it looses all gears, no drive no reverse. And sometimes when I start it, it just won't engage in D and R.
What do you think that could be?
it sounds like there may be something coming apart inside the transmission and it could be clogging up the filter? but i dont think a filter change will solve all of those issues
@@codemansauto208 would that make it work sometimes and then sometimes not work
Can I call you I just got my.transmission rebuild and still doing same shifts
I have a 90 f150 automatic and I don't have a b y forward gears. Where should I start looking for problems at?
sounds like your having problems with your forward clutches
i have a 1995 f150 automatic 5.0 it drives forward perfectly fine no issues but when i put it into reverse it like shakes the whole car and it wont move into reverse at all i dont know what to do or how to fix it please help
sounds like possibly the reverse band but you may start out checking the apply servo for that reverse band
What if it only happens after a long drive? Then I let it sit for awhile and it will go again just fine and shift smoothly? I don’t get it
either the torque converter is getting hot or your transmission filter is stopping up Hope this helps
got a 1990 Nissa D21 Hard-body pickup truck 2WD with a 4 cylinder automatic transmission. I got something wrong with the transmission are something. Let me begin at the beginning. I had the fuel pump go out why I was going to work and had to get towed 80 miles back home. And While I was being towed I had the truck in Neutral and didn't think nothing of it and keep being towed. But for the first 10 miles of being towed with the engine turned off. it still sounded like the engine was running. then all of a sudden the back tires locked up briefly for a tenth of a second then it didn't sound like the truck was running anymore. Then when I got home i changed the fuel pump and got the truck started I put it into reverse backed out of my driveway then put it into drive but their was no forward gears only reverse can anybody please put me in the right direction and tell me what I screwed up and what I need to change. I now know you supposed to unhook the driveshaft it you have an automatic and are being towed more then 10 are 15 miles
more then likely there is internal damage to transmission, i would drop the pan to inspect for metal
How much it cost to have a automatic transmission for a 1990 Nissan D 21 hard body 2wd
@@ryangreene9679 around 2k
My truck is a 1977 chevy 350 engine automatic transmission 4 wheel drive but has no gears at all it sounds like it's shifting but does nothing and I replaced the rear end fluid still nothing
Oh has transmission fluid
is it a 4 wheel drive??
Yes
A got a 1998 rav4 all wheel drive won't go forward or reverse and makes a grinding noise when putting itbin park. What could be the issue?
check out my broken axle video, maybe this will help you, this doesnt sound like a transmission issue ?
I can't find the video
I have a 2000 ford f250 7.3 powerstroke an I was driving in 2nd an put in back in to drive an heard a clunk an now I don't have any gears what could that be
is this a manual shift
Hey man I gotta ?.. my Ford ranger has no forward or reverse, not either move, is it the clutch?
thats what it sounds like if you have no gears and no noise going from drive to park
I have a 2001 GMC Sierra with a 4l60e. One day my truck suddenly acted like it was in neutral. All gears are like neutral but park still works. I replaced the fluid pump and it’s still doing the same thing. Any suggestions would be greatly appreciated.
Input sprag, or forward clutch pack, or pump , stripped splines in convertor.
@@ronniecox109 so I figured out that I didn’t seat the torque converter right when I put the transmission back in and broke the new pump. I now got a new pump (again) and it’s back in but I have no second or fourth gear. I was told that it’s either the servo or the band. I changed the servo and no change. I don’t know anything about the band. Like what position it’s supposed to be on or anything like that.
Shift solenoid A. is on in 2nd And 4th. Should show a code. OR if this is a used unit, The band applies on the reverse drum in 2 and 4 , a dished rev drum will result in no 2 or 4(OD). Or a servo apply valve ,stuck open
In the valve body.
@@ronniecox109 ok thank you. I’ll check those out tomorrow. If I have any other questions I’ll let you know. Again. Thank you.
Why my transmission kicks when shifting from one to second gear ⚙️ and second to third gear too??
Did you ever find what happened what was the fix
my buick le sabre 2005 goes in reverse but not forward but it goes forward in L 1, 2, and 3. Any idea?
sounds like it has a one way sprag broke in the forward drum
@@codemansauto208 thanks. Is it an expensive fix? I appreciate your comments
My 07 Chevy suburban only has reverse no forward gears …any suggestions?
Try to put it in manual low, if it goes thru the gears when you manual upshift then its your one way sprag but if it doesn't move then it could be burnt clutches
07 dodge ram 1500 trans will not engage, try to put in gear, but gears are spending.
-make sure the drive shaft is not turning while in drive gear.
-if it turns then your rear dif may be broke
- if its a four by four put in four wheel low lock and see if it will pull- that will rule out the transfer case
So I have a question, my truck transmission has always worked fine and all of a sudden today I put it in drive and couldn't feel it go into gear so I gave it some throttle and it takes a second and then it moves , what could be the issue?
My truck is doing the same thing did you fix the issue? Or what’s happened?
@@carlosv5117no transmission was toast, so I took out the automatic and converted my truck to manual.
@@jaynelson8743 damn really? How many miles did it have? You didn’t try to change the fluid that’s what I’m thinking of trying mines at 150k
@@carlosv5117 the automatic transmission had 370000 miles on it plus the previous owner drove it into a lake, so it had to have had water damage, truck is absolutely beautiful, but the motor was blown because of the water so put a motor in that only has 128000 miles on it, runs beautiful, and my 7f5 I just converted it to is a beast. So now the truck is badass.
@@carlosv5117 I'll make a short video of my truck so you can see how nice it looks and runs, so look on my channel probably on Friday.
My Saturn Ion 2006 lost all forward 2 weeks ago. The so-called expert at Aamco said tranny has bad clutch and priced the job at $1700.00. Couldn't afford it so had car towed home. Did some google research and found out that these Ion's have an issue with a feed pipe that is located under the transmission pan. The pipe breaks at the weld and usually car will only lose forward gear. Took a chance and ordered the feed pipe from Amazon for $124.00 and sure enough the pipe was broken off at the weld. Slapped in the new pipe and car runs perfect again. Sadly, we can't always trust the word of the so-called experts. Here's the how-to video of the broken feed pipe. ua-cam.com/video/jW9h-9TEOn0/v-deo.html
you did your homework and that's awesome!
that's what I like about youtube it keeps mechanics honest!
I already have a video about this tube but it is Titled under Cobalt and HHR
I didn't add Saturn because Saturn put a CVT transmission in some of their cars and I was trying to keep from confusing anyone