As an actual professional I can say we would do that differently. For one the industry standard is mig/pulse welding and not stick welding and two I would have laid the pipe flat then welded the patch on and lastly, we would have used the same thickness of material as the pipe.
No bevel and you ground down the cap which is only acceptable on a full pen groove weld. If its a short term repair sleeve it and weld it like a lap joint, you could probably knock that piece out with a good steel toe boot theres such little penetration.
We were trained to use a sharp piece of chalk and punch marks. Plus we were not allowed to over lay. We always inlayed and beveled all our cuts. Also all corners were rounded because we were dealing with pressure vessels. All our cuts were flame cut and our bends were made at a break press or roll benders. Course not all of these jobs were performed in this manner due to conditions in the field etc. Over the years I found out there are a few ways to skin a cat sort of speak. I watched others getting precise accurate results using methods I would never use!
Это сколько же электродов надо сжечь впустую... А из обрезка такой же трубы сделать не додумался.И не надо по ушам ездить а вот если да вдруг,не окажется под рукой...
Great video.. I’ll go with the last option... I did notice as you were shaping the curve, there was a notch about 3 inches on the top, it wasn’t there when you fitted. Is that the same piece
this isn't proper way and some applications it in necessary to do things a certain way . welding is much more then sticking metal's together unless your tinkering a bunch of junk metal to make a go-kart or somthing
La mejor reparación a mí entender, es la tercera. Siempre y cuando el grosor del tubo permita curvar la chapa. Sí es muy gruesa, también se podría curvar añadiendo calor al proceso. Grande el mundo del metal y las reparaciones!
To be honest with you....as a hobbiest you could probably do something like that but in real world application is totally useless,and if a welder don't want a show those so call "tricks" that you just share in the video is because no real welder would do something like that. Five minutes of my life that I will never get back.
It's hard to keep comments respectful when there are people showing so called tricks that might get others killed. Pay someone to teach you the correct method to do the job. Fortunately nature has a way of dealing with that through natural selection.
Se llama soldadura de ventana ( welding Window), el soldador está muy lejos de ser calificado,.muy malo para soldar . Le falta pulso y mejor acabado a la soldadura, de verdad impresentable,.practique más.
I'm a welder, and I don't care who knows how to fill a hole.. but if I would ever considered this it would be because I wanted to get fired at my job 😂
Спасибо да богословит тебя боги
никому не расскажу эти секреты особенно сварщикам
Узнают засмеют😁
Узнают убьют, прячься ,,😅
😂😂😂😂😂😂😂
Интересно для кого такие крутые лайфхаки! 😂😂😂
🤣🤣🤣🤣
А секреты то где ? В видео ничего кроме глупой лишней работы нет . Зря потерял время .
Прочииал ваш комментарий, Благодарствую,что сэкономил моё время .
Последняя вставка вообще не та что гнул, гнул максимум 3 мм, а вставка родная, та что вырезана от этой трубы.
Кроме глупой, лишней работы нет. Есть пол ляма просмотров)).
@@user-ir4yf8ci8e просто люди деградируют - не думать проще чем думать
A lot of this is definitely not what a professional would do. I promise you that.
a lot? NOY ANY!!!!
As an actual professional I can say we would do that differently. For one the industry standard is mig/pulse welding and not stick welding and two I would have laid the pipe flat then welded the patch on and lastly, we would have used the same thickness of material as the pipe.
Поверьте сварщик такой ерундой не будет заниматься. Это сколько лишних швов надо положить. Трубу кусок срезал вот тебе ладка.
No bevel and you ground down the cap which is only acceptable on a full pen groove weld. If its a short term repair sleeve it and weld it like a lap joint, you could probably knock that piece out with a good steel toe boot theres such little penetration.
You grind down the cap if the prints state that finish on the weld symbol.
С трубы не сцдьба латку сделать?А это дурная работа
العملية رقم 3 أحسن طريقة و أتقنها
Рулетка в руках сварщика это нонсенс!)))
Where are those damn welders who do not want us to know these "secrets" ... So, the welding mafia does exist...!!! 🤔😲😜
The first rule of weld club is ...
They've got a secret hand shake and everything.
All of them are gangs in any job🤣🤣
Some secrets are best kept secret...this is one of them.
А что тут хитрого? Обычная сварка, я печку делал и не такое варил
Once.iş.guvenliyi.yok.izlemeye.deymez
Man, you didnt need to cut the plate. All you need to do for up to 6mm is tack and hammer, tack and hammer....
agree, i ges he teaches to beginners.
3 weys to do weld it.
He showed all 3.
Man,you should've watch the whole video before entering the comment section. It's a complete guide
Very good , more than one way to do the job , shown all three , very good teacher .
We were trained to use a sharp piece of chalk and punch marks. Plus we were not allowed to over lay. We always inlayed and beveled all our cuts. Also all corners were rounded because we were dealing with pressure vessels. All our cuts were flame cut and our bends were made at a break press or roll benders. Course not all of these jobs were performed in this manner due to conditions in the field etc. Over the years I found out there are a few ways to skin a cat sort of speak. I watched others getting precise accurate results using methods I would never use!
Your way is the proper way to do this . No bevel essentially makes this a ground down fillet weld.
you should make a vevel and use 6011 or 6010 for the rootpass.
He can use even 7018 or 6013 but yes, 6010 or 6011 is easier
bevel, root pass 6010, cover with 7018 done
Very good work
3 вариант лучше из всех))) Когда выгнул по трубе один лист а вставляешь тот который выпилил)))))).
😂😂😂😂
Ты тоже заметил эту херню
Да, мне тоже показалось что он конченный😂😂
5 минут шняги,большой и толстый диз
Это сколько же электродов надо сжечь впустую... А из обрезка такой же трубы сделать не додумался.И не надо по ушам ездить а вот если да вдруг,не окажется под рукой...
Просмотрел несколько раз и не понял смысла этого ролика.
@@user-jz5zq8os6r Аналогично🤔
Вырезать кусок трубы,чтобы потом из кусочков делать...
Может не хватило мысли родной вварить.😄
@@user-hi9sk7zj1s так он этот вырезанный кусок потом и вварил, думает мы идиоты совсем такой бред за ним повторять
Very good.
number 3 i like...good job👍👍👍
Greats Tips ! Thank You
Можно было и без подрезов согнуть
un genio!! gracias por compartir. Es el segundo video que veo y está excelente!!! suscito.
Who comes up with these titles? I've spent at least10,000 hours of my life welding. I couldn't care less who knows this....
Great video.. I’ll go with the last option... I did notice as you were shaping the curve, there was a notch about 3 inches on the top, it wasn’t there when you fitted. Is that the same piece
It always seems welders want people to know the PROPER way of doing things and to stay away from short cuts.
this isn't proper way and some applications it in necessary to do things a certain way . welding is much more then sticking metal's together unless your tinkering a bunch of junk metal to make a go-kart or somthing
@@clittle1559 that's why I said welders want people to know the PROPER WAY, NOT this way.
amazing amount of extra work
La mejor reparación a mí entender, es la tercera. Siempre y cuando el grosor del tubo permita curvar la chapa.
Sí es muy gruesa, también se podría curvar añadiendo calor al proceso.
Grande el mundo del metal y las reparaciones!
I was a welder for 40 years and I wouldn't recommend any of this.
Jaki problem wygiąć drzwiczki w łuk, nieprofesjonalne podejście do tak prostego zadania. Pozdrawiam
The 3rd approach would have been my first.
Thanks you my friend
Abría sido más fácil soldar 4 puntos luego echarlo al suelo y recién soldar así no hubiese gastado tanto electrodo
Que dijo?
Ya pero esq son rusos y si no lo.hacen difícil no se quedan contentos 😁😅😅😉
@@famosisimo jjajajaja muy buena yo mire el programa ese que necesitaba un traductor jajajaj
Y no solo eso, para hacer esos tipos de trabajos hay que hacerlo en 3g
@@angelorivasvera2080 🤣🤣🤣👍👍
Is not that they don’t want you to know, they don’t know themselves. You can’t teach if you don’t know.
Это же генеально!!! 😂
I’m a welder…I don’t give a crap if you use this trick. Why wouldn’t welders want you to know this trick?
Oh Gawd,,,someone started a welder,,LOL
Good job 👍
Для этого видео х2 скорости мало, не часто так бывает
To be honest with you....as a hobbiest you could probably do something like that but in real world application is totally useless,and if a welder don't want a show those so call "tricks" that you just share in the video is because no real welder would do something like that.
Five minutes of my life that I will never get back.
I gues they only have stick welders there.
Third is the best
It's hard to keep comments respectful when there are people showing so called tricks that might get others killed.
Pay someone to teach you the correct method to do the job. Fortunately nature has a way of dealing with that through natural selection.
Me cuts same thickness then bends it with ofc grinds a bevel on both parts clean around them and do a open root v grove
3rd one is good
I'm still waiting for the 3 tricks.!
Nice work enjoy the video thanks sir for that
Perdí mi tiempo pence que Hiba a ver algún trabajo especial,
Не знаю ,если честно херню показали , я лично ,в даной сетуаций варю без всяких подрезов, походу подганяю просто делать надо не спеша
I needed a good laugh……🤣🤣🤣🤣🤣🤣🤣
Se llama soldadura de ventana ( welding Window), el soldador está muy lejos de ser calificado,.muy malo para soldar .
Le falta pulso y mejor acabado a la soldadura, de verdad impresentable,.practique más.
Aaaaamonos camión!!! Otro cerebro super dotado. Egresado de la nassa jajaja😂😂🚀
Tiene razon amigo ramon.....pero este tio le falta todavia
Here's an idea. Use the piece you cut out.
I'm a welder, and I don't care who knows how to fill a hole.. but if I would ever considered this it would be because I wanted to get fired at my job 😂
The second one is best
Que buen video
А секрет в том☝ , что дыру в трубе можно закрыть латкой из металла 👍КЛАСС😂😂😂
Mate stick to stacking supermarket shelves, that was a waste of time
Y cuál es el truco ahí no le veo nada de otro mundo
Просто гений, прививка от ковида сделала своё дело! 🤔🤔🤣🤣🤣🤣
يامعلمممم
What a load of croc! If i did that at work i would have no job! 😬
المش فاهمو ماشاء الله اول قناه عربيه تصعد والغريب التعليقات كلها اجنبيه صراحه مش فاهم حاجه
Не всем интересна сварка...
So to get an accurate measurement it's required to pull out the tape that slow?
its down to health and safety. Don't want you pulling a muscle pulling it to quickly 🤣
@@grantashby5390 lmfao🤣🤣🤣🤣🤣
ขอถามก่อนดูคลิปจบนะครับ
no conozco tu idioma. pero gracias
the last one is simply a misleading.... you bending a 3mm but you use a peace of cutted pipe 😂
mantap bos q
Что здесь ваабще происходит
Какой у тебя сварочный аппарат?
GUANDO A MÁQUINA E BEM REGULADA E A MÃO DO SOLDADOR E BOA A CASCA SOUTA SOZINHA,!
Rất hay !!!
I'd like to know how to keep my fingers and nails all pretty and clean, like that. Mine look like an APE's and I use gloves when I'm working.
Good
Mictr
Jgn lupa mampur
Why didnt you use the cut out for the door
reason welders dont tell you about shit like this is because we would never do that
I want to see how this seam goes through flaw detection. And yes, fire your locksmith. He does not know how to prepare the welding area at all.
This isn't a job for a welder its a job for a fabricator.
جميع الطرق جيدة ولكن الطريقة الثالثة افضلهم
3 способ хороши 👍3
No es algo que un soldador tenga que ocultar.
Что тут особенного?где 3 хитрости? название ролика не соответствует самому ролику.
Wy not sticky tape and then measure the tape?
Tui xem 3 thủ thuật này nhưng quên mình là thợ hàn 🤣
What did you do with the piece you beat around the pipe. The piece you put in there was the piece that was cut out of the pipe
Когда делать нечего можно фигнёй пострадать!
Y para que marca el Flex si para eso están los números y los milímetros entonces uniera medido con la misma lámina🤪
Tack the plate at one end , get the oxy bottles out heat and bend around the cylinder. So much easier.
Обычно это делают гипсокартоном. Очень хитрый сварщик.
Put a spacer under
ГЛАЗАААААА........ матвеева в студию
مشاء الله good very nice 👍👍👍👍
منورني والله
Меня этому учили в ПТУ в 17лет.
Pretty cold weld piled up to high.
Đây ko phải là cách lên dùng ... kết cấu ko bền vững .. mất quá nhiều thời gian.. và ko đủ thông số kỹ thuật
Valeu Brother Thank you ! Mui Bom excelente 👍👍🤝🤝🤜🤛
Oh no the welding trade is not safe the cats out of the bag
это хорошо чтоб мы не знали такую залепу, спасибо всем сварным, кроме этого сварного
Root pass first 6010 then 6013 or 7018 for full weld
Про какие хитрасти я не понял,нет тут ни каких хитростей.
Los soldadores no queremos enseñar estupideces, por eso no queremos que la gente aprenda a perder su tiempo.