Assembling & Running a WORKING 4 Cylinder FOUR Stroke Model Engine - Toyan L400 Engine
Вставка
- Опубліковано 7 лют 2021
- ►TOYAN FS-L400: bit.ly/3jxejdR
$100 OFF Coupon Code: L400 , Only $699.99 ,Save $100
►Starter kit: bit.ly/36ShQhS
►Toyan Engines: bit.ly/2VGhYuR?ref=8_o3dxgl2qw
►Toyan Parts: bit.ly/3rzyY3D
}}}}} Use code: jq90 for 10% discount {{{{{
--------------------------------------------------------------------------------------------------------------------------
►NEW UPCOMING TOYAN V8 ENGINE!
➜ bit.ly/3rkRM94
--------------------------------------------------------------------------------------------------------------------------
►Tools that I used on this video:
➜ 63 in 1 Multi-Tool Magnetic Precision Screwdriver Set: ban.ggood.vip/WLKy
(code: BGHKC5, 35%off)
SEQURE SQ-ES126: ban.ggood.vip/WLKx (code: BGSQES126, US$85.15)
---------------------------------------------------------------------------------------------------------------
►Subscribe! bit.ly/2m1d1y7
►Instagram: johnnyq_90
►Support my videos!: / johnnyq90 - Наука та технологія
Nice job man! Just a little tip, installing components should be torqued from inside out to make sure it all stays flat. Just like a sticker where you start in the middle and work your way out in a cross pattern. And after setting the timing, always turn the crank 2 revolutions by hand to make sure valves and pistons don’t collide.
Yeah, that oil pan installation was painful to watch.
Although he's not using enough torque to really deform anything, those o-rings could get wrinkled up very easily and cause a leak.
i thought the same thing. he also never torqued the connecting rods. ouch.
@@Mike-Minion I don't think he's planning to do 100,000 miles with it.
It's a video showing what's available and how it works.
Or that it even does.
@@andysaunders3708 so i guess you and him have a 1000 dollars to burn then. Cool. More fun to watch later.
@@Mike-Minion That's me, mate. Mr Moneybags.
This gives me so much respect to mechanics that can do this on such bigger scale and more components
TBH smaller scale looks a lot more complicated than a regular I-4 fewer tiny bits to lose for sure.
@@truegamer_007 It requires a lot more work and time to assemble a real engine
@@truegamer_007 That's why it's harder. Needs more tools and knowledge as well
It's a job.
@@truegamer_007 You don't really see many sensors etc on these miniature models, neither torque settings. Also timing belt is very simple on this one, compare that to real engine which might have tensioner, few guide pulleys etc. How about adjusting a diesel pump as well. Awesome work anyway
Thank you, for not having some annoying music playing for the entire video. I much prefer just hearing the sounds of assembly.
When tightening things like the oil pan, valve cover, and especially the cylinder head, you should start in the middle and work to the ends in a spiral pattern. If you tightening from the outside in any warp induced will be locked in instead of flattened out.
when i saw how he was tightening them down i cringed a little on the inside...
Repent to Jesus Christ
“He cuts off every branch in me that bears no fruit, while every branch that does bear fruit he prunes so that it will be even more fruitful.”
John 15:2 NIV
h
@Tim Rock-It Saunders yea this is the method, i call it an x pattern start from the middle and do the outside then back inside then out etc.
It's the first thing you learn if you decide to become a tire technician, or any technician in that industry
Thanks Captain obvious
I’m yelling at my phone “do the main bearings before the rods”!!!!
Continued watching and there aren’t any mains. Haha!
Found another mechanic
@@kyleculp7520
It also got me all riled up when he put the valve train lube on after assembly. I was like “put a drop of oil under the valve spring cups and assembly lube between the rockers and the cam”!!! Haha, old habits die hard.
@@MrCarnutbill67 Exactly! I wonder why they went with no main bearings??? I'm guessing they did it to keep costs down, which they definitely did. Looks like a forging? (same sort of finish on the unfinished parts of the crank as a lot of powersports con rods) Let's hope so...
Dude i was sh*tting bricks when he didnt check the gap of the rings
@@garrettliepelt8148 them rings have a mile wide gap 🤣
I found this very informative as it is easier to see on this scale where every parts goes as you can just turn the entire engine upside down and film from every angle. Also helped a lot with all parts lined up like that and watching them be put on one by one.
As someone who has done some engine work this looks like so much fun. All of the fun of assembling an engine together without any of the heavy lifting and busted knuckles
I agree!
This blows my mind. I work on cars and seeing this small version of what I do is crazy. Love this channel and will subscribe
That would be cool if you took an online Mechanic course and they sent you this for the semester test!
sure, after you build the thing, you get $150,000 year job.
Sure, this would be a 20,000 dollar test.
This is a toy, get real
@@chakstak3684 a "toy" that runs on gasoline? shut the fuck up.
@@whw710 has the measures of a toy, an expesive toy
When the wife says no more car parts in the house, just make em smaller.
Well a 4 joke stroke is fun to bash with hammer and rev tilted up side down. lets see a 4 joke survive with just oil injection tilted running in any position, it would be a fun experiment as 4 joke3s are as plentiful as dirt in the auto industry. what a wast of an engine!
ok boomer
But she never said Anything about motorcycle parts! >.>
800 dollar piece of junk.
@@jlo13800 two strokes are great for recreation but too much maintenance for a car, which you probably wouldn’t plan on driving upside down anyways. Plus you don’t want to have to mix a full tank of gas for a car. 2 strokes are great but you have to take application into account
The smoothness of the sound of the 4-cylinder engine is very good and cool.
so addicted to this, building my new shop for my r/c trucks and ordered some new equipment. thanks for the inspiration!!! pro diesel tech for 35 years and now i only want my hobby shop!!!!!!
I can watch this build on replay mode all day. Too cool! Love these "little engines that could". Thanks for sharing
Check out "It took me 500 hours to manufacture this 7 cylinder engine" on YT.
The guy machines EVERY component himself and it is just perfect !!
One day I will get to do cool projects like this.
Why not today?
Go buy a used car engine and do it. Rebuilding it will be cheaper than buying one of these.
@@2Skinny Nat after buying the supplies and tools. But not a bad idea.
@@norsevikingsir4932 tools last forever, which means you can always re use your tools for damn near everything...
@@fuckngreat8955 Still the tools need initial investment and if he wants to do just one it might not make any sense. This small engine is doable even on office desk or maybe kitchen counter when negotiated with wife. For full size engine you'd need a garage or something like that, not going do drag it into your apartments living room.
The machineing and finish is excellent,, so so amazing. Its a work of art on its own just set out in the box .
I feel like this would be a good first step for someone who had little knowledge but wanted to understand the basics of how an internal combustion motor works. Ive done a bunch of accessory work like brakes, alternator, tensioner, radiators, and water pumps. A front main seal even. What I've never done is tear down a motor. Speaking of seals I'm in need of a new rear output drive shaft seal. That'll be a first.
As a mechanic of 33 years and still going, I really enjoy your channel!
Hello sir, is it possible for me to make such a small motor on my own using the unique and the output? Is it possible for that please explain
i think the screw driver with torque selection was what really impressed me the most. Never seen it before
Wow, that is great! I'd love to design that into some kind of coffee maker or something around the house. Maybe an alarm clock .... if you snooze it too many times it will just bounce off the rev limiter and threaten to blow up, so you've got to get up because it's expensive to replace. Very cool.
This has now made me interested in these kinds of model cars with working engines. looks like I found a new hobby thanks to you
The next stage is for you to *make* something like this. Of course start with 1 cylinder but I feel like you’ve got the skills to make a good job of it
Hey just a notice.
On fullsize Parts you tourque from the inside to the outside.
Imagine a bowed pice of paper.
If you pin the outside Down and stop in the Center you get wrinkels.
If you start in the Center and stop on the outside it can "squish" out without any crazy deformations.
Sorry for Bad english, its late af Here in germany 🤣
LOVE Your Videos, keep them goin!
Your guidance is SPOT ON! Your spelling? Not so much... it's "wrinkles"
It's called snail torque sequence
No that late
Yes, I was thinking the same. He did the sequence for disassembly instead of assembly! Oh well, it's just a toy, and it seems to run quite well.
I was unimpressed with the fact that it's only sohc. At first glance, the second (idler) pulley looks like an actual cam shaft. They should have just made it dohc, with the cams directly on top of the valve spring buckets. Maybe that can be a future job for Johnny!
Still cool though, but for $700-$800, it could be better.
Your English is spot on! I’m quite impressed, kudos to you, and love from the U.S! :3
This is jaw-dropping cool.
Really, I am stunned at the details on this tiny engine..🤩
crazy right
pretty dope man enjoyed watching this come together
When I look at the engineering here I just feel humbled !
Grab a file! Start gettin subtractive!
Ah this is where Stuart Little gets his race engines built! Haha excellent work!! I love the individual throttle bodies and velocity stacks. Too cool!
Looks like a good Father’s Day gift.
Works of art. The people that design, build & maintain - artists.
YES YES YES! A project I can do!!
You have just made my summer. Thank you
I love this site
This the coolest thing that I've ever seen in a while! I'm just starting to learn the ropes about car mechanics and I think it would be really helpful if I had an engine like this to build.
It costs a grand. You’d be better off buying some cheap used full-size engine. Would be cheaper and would translate much better into real world engine experience
@@jamesbizs 1) not true outside eu / us
2) normal engine requires heavy equipment, space, and specific tools
Maybe you could start out on an old Briggs and Stratton motor
Just use a lawn mower engine
Just start with small motors on lawn mowers four wheelers dirt bikes etc
Didn’t even know they made these. Damn wish dad was still around to see these he would’ve been blown away. I work on the full size ones and used to do model kits, but never got into the RC cars except messing with friends setups. Think I might try to build one with one of my brats at some point.
Huge respect to mechanical engineering! It makes our life easier!
Nice vid as usual :), thanks for sharing. I just wanted to mention that plane surfaces (head, covers...) have to be tightened in the middle first and then over cross to the sides.
Don't know why this video is so mesmerizing to me. So cool to watch.
These kits look really fun to build. All of those tiny machined parts are impressive on their own.
Yes, the machine work blows me away!
Onde comprar ??
Quanto custa no Brasil ??
do you know if they use petrol or water as fuel? And does it actual produce any drive?
I had a plastic see through engine when I was 7. Had to assemble it and it worked after assembly. 11 years later I rebuilt my 72 CJ5 and a 73 Le Mans gt.
Excellent work. DOHC, precise torque,timing marks and all. An engine build like any other. Bravo!
SOHC**
Imagine a 2JZ model Engine with its inline-6 pistons 🤤🤤
If Toyan will make it, it should have at least a middle support for the crank shaft
@@firionrazar3797 It looks like they managed to make some decent bearing for the conrod so i guess if they managed to make a thrust bearing at this size it's doable.
Or a small block lol
Well maybe be a N/A instead of Twin turbochargers.
But we know y Toyan, if they want to make a mini Mazda 787B three rotor engine they'll do it.
@@matthewmondragon2074
Imagine a 26B 4 Rotor as a Model Engine ❤️👌💪🤤
Or making a 𝓐𝓵𝓯𝓪 𝓡𝓸𝓶𝓮𝓸 V6 Busso
This would be an awesome Christmas gift.
Am i only one who thinks that all screwing scenes are so satisfying to watch?
This engine is an absolute work of art. I build engines for real, but this is on an entirely different level. This is absolutely beautiful.
Would you say it's ... on a different scale?
Levels to this scale
Ahh this was so relaxing to watch
Loved every second of this video. Thank you.
Looking forward to the real deal!! super excited
Can't wait for EP.2 of this, when JQ grinds out his own lumpy cam and makes this thing sound even better lol
nobody:
the boys: yo lets turbocharge it
They make turbo intakes that go on you key chain soo...
I bought the red paint. Let's goo.
ua-cam.com/video/2xx_2XNxxfA/v-deo.html
Llllb
ebay turbo!
OUTSTANDING !!
Without the modern Computers, Laser Cutters and micro machining of today, this would be impossible.
Humanity is limited only by the imagination
It's actually so cool this way it's much easier to learn spending less money but still having fun
Engine runs smoothly. 😘
Wow a Khmer youtuber? Ima have to go check your channel out haha
@@nMURKv mi
For sale? What the price?
I want to buy a recreational vehicle like this. There is shipping to Kuwait
@@nMURKv 😘😘
This as a training tool is amazing .
I've tooken small engine repair in high-school I've done quite a few 4stroke and 2stroke. This is actually pretty cool. All it's missing is a ignition module and coils.
Take grammar first.
I love watching these smart car engine builds
Had smile on my face the whole time :)
This looks like my dream project 🔥🔥
4:42 For the oil Pan on bottom of block don’t tighten in cross pattern, tighten from inside out, it keeps the gasket smooth from the inside out. (Not a hate comment just a helpful tip) very great video. Thanks for posting
how do u know its helpful? entitled child
Me and my boy had a plastic version of this from Discovery Kids and we had a blast building it together.
Good times for $50
👉📣 WOW it's working and sounds like the real one 💕 excited to see tiny robotic figures will be driving and racing little cars in a specific places in the near future independently 👍
Excellent! The only thing I would have done differently, is to add silicone oil or grease (as appropriate) on each part during assembly, e.g. greasing the rockers beforehand, not putting it on top as at 9.30. 👍👍
1:08 YO! STILL USING WINDOWS 7! WHAT A WARRIOR!!
Is the most reliable Windous system for most of operational as Adobe Reader, programing systems and more, but unfortunely their backup was shut down years ago.
What a great product, man I love this thing. Thumbs up.
2:54 you would think they would give you a piston ring compressor 😂 I loved that part of assembly. Freshly bored and honed - yep, still talking about cylinders
Nice work bro! Now lets see you put it in a car. Come on, we know you can :)
But first he has to supercharge it!
Watch the whole video, he said he would.
@@Donnerwamp nah, he needs to turbocharge it with that micro turbine he made in another video
@@trfpvVT It's belt driven, it's a supercharger. A centrifugal supercharger, to be exact. A turbo would be driven by exhaust gasses.
Umm just gonna put theirs out there that in a rwd drift car would be awesome
This is actually a good way to learn about engines but on a much smaller scale...Now I'm not 100% sure about if every part is an exact replica of the "real" life size parts in cars we see everyday, but the fact it has all be downsized is convenient for teaching and learning the overall basics! Pretty darn cool I'd say!
I had so much fun watching this video, thanks
Hermoso trabajo en diminuto. SINCRONIZACIÓN TOTAL.
Lets Go! Can't wait to see what you do with this!
The video has only just started and am commenting how great this build looks. And that torque wrench was sooo cool.
I don't need one but I want one so bad.
Dude this is literally the coolest
This is the most awesome thing I've ever seen.
Wow, that's a really nice looking kit! the stuff we dreamed of as kids eh?
I love your work man, please keep this videous comin, so satisfying to watch😄
Nice build!!
This is so cool man!!!
Jóia de mais, parabéns 👏👏👏
Incredibly fascinating. This engine building should be mandatory for all desiring to get involved in automotive and combustion engine tech. This could also be a part of a larger project but this engine build is fantastic!
I can not believe the crankshaft is not supported by more than a bearing on each end! The crankshaft has got to be supported in between every cylinder or it will break. Inline 4 cylinder engines should have 5 main bearings and inline 6 cylinder engines require 7 mains. I hope Toyan builds an inline 6 someday.
Gosh - it's like a piece of mechanical jewellery. How clever and constructive humans are, when they want to be...
Nice video I really like those engines. Keep up the good work
Awesome, this channel gets all my inner Lego Builder neurons firing lol
I'm tempted to buy this for a mate of mine who's an engine builder and a fkn top bloke
This is so badass on sooo many levels...
Notification squad. Can't wait to see what you have in store for us this time.
I wanna see this company make an engine with an oil pump and clearances. Some thrust washers on the crank and more crank shaft main journals so it can handle some boost 😈
@Joshua Jason Karl lol I’d buy a civic with that 700$
This was awesome!
Very cool. I might pick this up as a hobby
I've seen this today, what a way to end St. V.
Thank you Johnny.
My favorite is the "Explosion View" at 1:04.
I've thought about buying 1 of these kits... They look really fun, really accurate, metal parts & tools, not cheaply made, BUT not cheap to buy. LoL
Far-out, I love this autominiture technology, it's got potential👍👍
Torque sequence! Always start inner to outer
Especially for the cylinder head!
thank you! i was hoping someone else caught that.
i was triggerd when i saw the oilpan, then the head and started looking through the comments when i saw the valvecover
LOL, ik was looking for this comment.
@@DidricSundgren Yeah same lol, even if it's not as important with these smaller engines I'd still do it that way for peace of mind. Also nice Merc!
10:18 almost got me heart attack I didn’t realize the speakers were at the maximum sound level.
I feel you, I have just resurrected.
Subbed! Can't wait to see this in the car! Been watching RCwizzard's grave digger build for years, I'll keep up with yours too!
as a absolute engine finatic,having one of these would make my day 😁👍🏼
I just wanna see in future tiny like this 2JZ engine, that would be incredible
A ferrari v12
@@User-rj2dk ua-cam.com/video/SeUMDY01uUA/v-deo.html
Es
4-strokes are shit - this world needs less SCAMdemic and Climate Change BS, and more 2-STROKES, AGAIN !!!!!!!!!!!!!!!!!!!!
My 2-stroke unrestricted 125cc motorbike does 90+mph, and these crappy 4-stroke 125's cant even get 70mph... 4-strokes are a joke, even if they are technically 'clever'... !!!!!!!!!!!!!!!!
And I've only got 1 x exhaust - these shitty 4-strokes have 2 x exhausts... !!!!!!!!!!!!!!
Fuck 4-strokes !!! :)
That was so friggen cool and satisfying when it started!! I literally had a massive smile on my face hearing it's little revs lol
I love thing like this. I had this bmw straight 6 engine from a 98 316i. I have had it since a kid.
My dad made this stand so I could have it in my bedroom and everyday I would strip it down and put it back together.
When I moved out of my mums I couldn't take it with me as I moved into a flat on the 2nd floor with no lift.
I love to work out how things work. Its the only thing I'm good at is fixing things.
I would give anything to have that engine back but it's too heavy and I have just been diagnosed with MS so my hands are not plugged in properly.
This looks like its prefect for me but out of my budget.
Come on that price is stupid. They have that on a 90% mark up. There is no way that costs $100 no manufacture let alone $900.
I could buy a whole damn car for that price.
amazing work 👌🏻
The layout and clean look is already eye-catching
We’re in the big leagues now my friends.
Cool to watch. I've heard the best way to learn about and how to fix engines is starting with an old lawn mower.
This is awesome!