Removing fuel rail, injectors 350z Vq35de
Вставка
- Опубліковано 17 бер 2017
- How to remove the fuel rail and replace injectors on a vq35de 350z. I Did this video to help others instead of nissan ripping your wallet in half lol. Hope this helps and please like and subscribe for more videos. Instagram @350z33vq
- Авто та транспорт
Saved me a lot of time. Very helpful
Helped me out. Thank you!
Thanks brother from Canada
Thanks for this, man. I have a 2002 Maxima SE and am troubleshooting a misfire on cylinder #6, I believe I could have a leaky/faulty injector. Our cars have the same motor, except yours is longitudally mounted. It looks like both rails have to come out even if you're only replacing an injector on a specific cylinder bank.
Matt Scott dam is this the same for 06 maxima?
Helpful video. He should cover the intake manifold holes lest something falls in.
Thank you for this video i finally know how to change them myself. Most people make these videos and it look so hard but you sir have helped me out
Thanks for getting right to the point instead of starting with a 45 minute introduction like "HAHAHA, HELLO UA-cam AND THANKS FOR SUBSCRIBING. IT'S ME, DIPITY-DUMB-SHIT, THE EXPERT OF EVERYTHING COLORED BLUE, TODAY WERE GONNA PAINT COMMON SENSE YELLOW CAUSE I'M AN IDIOT AND LIKE WASTING PEOPLE'S TIME"
When removing injectors do we have to remove the fuel pump sensor or it can it be done with it on
Thanks going to replace mine
How everyones performance after changing these?
What injectors did you use??
On the VQ35DE when removing the fuel rail for a headgasket job would I have to release the fuel pressure?
what you could do is pull the fuel pump fuse, run it until it burns up the rest of the fuel, then do the procedure
@@bumkinboy63 Ok thanks a lot. I'm gonna start on it and hopefully I can get the timing right. Take care!
clean it with what?
thank you brother . .. what did you notice that you had to change injectors ?
did you have a misfire?
xTORR Xx asking same
What made you change injectors? I have a misfire but good plug and coil. Dead mis p0303
Brandon Kizzire i have the same exact issue with good coil and plug right now im currently changing mine because my miss will go back and forth from missing to running smoothly but weakly and i dont see anything else being the issue
Lol po305 here.
What did you do?
Mine too! What was your solution?
I have a p302 cylinder 2 misfire code but only a slight pop audible from the exhaust at idle car still runs fine and has power. I have swapped the coil pack and spark plug between cylinders 2 and 4 and the code stayed on cylinder 2. Is this more likely to be the intake gasket or injector? I only use 91 octane Mobil gas and the check engine light never blinks only comes on after a few days of driving.
Can you tell me if you fixed it? if so... how? please
@@5ermad Mine was the intake plenum gasket between the upper and lower parts of the intake manifold. Fixed the pop at idle and CEL.
What where these injectors? Fbjc100?
fbjc100 is for the 3.0L, this is the FBJC101.. for the newer versions of the VQ35DE engine uses Bosch part # 0280158005, a popular upgrade for anybody looking to update early 2000's jecs injectors
www.injectorplanet.com/collections/jecs/products/jecs-fuel-injector-for-nissan-infinity-3-5-v6-4-5-v8-part-fbjc-101
www.injectorplanet.com/collections/bosch/products/bosch-fuel-injector-for-nissan-3-5-part-0280158005
very informative video
thank you
-Bryan
I installed fbjc100 on my 04 350z steady 21.6mpg every time.