Crystalyte BLDC Hub Motor Bearings Replacement after 10,000km (Stealth E-Bike)
Вставка
- Опубліковано 16 сер 2020
- Channel Support - www.paypal.com/paypalme/evcus...
EV-Customs Website - ev-customs.com
Instagram - / ev_customs
Facebook - goo.gl/tu3Qdk
Music - Kontekst No Copyright Music
English
In this video you will see a bearing replacement in a BLDC hub motor of Crystalyte, as you will see in the video the Bearings have rusted from moisture and will be replaced with new ones.
Russian
в этом видео вы увидите замену подшипника в ступичном двигателе BLDC компании Crystalyte, как вы увидите на видео, что подшипники заржавели от влаги и будут заменены новыми.
German
In diesem Video sehen Sie einen Lagerwechsel in einem BLDC-Nabenmotor von Crystalyte, wie Sie in dem Video sehen werden, in dem die Lager durch Feuchtigkeit verrostet sind und durch neue ersetzt werden.
Italian
in questo video vedrete la sostituzione di un cuscinetto in un motore con mozzo BLDC di Crystalyte, come vedrete nel video i cuscinetti si sono arrugginiti dall'umidità e verranno sostituiti con dei nuovi.
French
dans cette vidéo, vous verrez un roulement de remplacement dans un moteur de moyeu BLDC de Crystalyte, comme vous le verrez dans la vidéo, les roulements ont rouillé à cause de l'humidité et seront remplacés par de nouveaux.
Spanish
en este video verá un reemplazo de cojinete en un motor de cubo BLDC de Crystalyte, como verá en el video, los cojinetes se han oxidado por la humedad y serán reemplazados por otros nuevos. - Наука та технологія
![Lp. Последняя Реальность #107 РОДНОЙ ДОМ [Финал] • Майнкрафт](http://i.ytimg.com/vi/IK3QKzKUlHM/mqdefault.jpg)
Thank you for the video. I love the resourcefulness and creativity with very modest tools!
Thank you for the time you spent to make and upload this video.
Awesome video man. I was gonna say for others watching to avoid touching the disc brake contact area with bare hands. But then I saw you clean with spirits after lol. Great to watch and good music too.
Thank you mate!😄
U can also little warm up the aluminum with torch but careful. Since aluminum is great er thermal Expansion than steel bearings it will expand and the bearings goes easy out
Maybe take the rotor off next time to keep the grease off it?
Very good !!
There is no way that I would be doing that with the brake rotor still attached.
sorry to be offtopic but does anybody know a method to log back into an instagram account??
I stupidly lost the account password. I would love any tricks you can give me.
@Kason Trevor Instablaster ;)
@Ayden Liam thanks for your reply. I got to the site on google and I'm waiting for the hacking stuff atm.
Takes quite some time so I will reply here later with my results.
@Ayden Liam it worked and I finally got access to my account again. Im so happy!
Thanks so much, you saved my account !
@Kason Trevor Happy to help :)
Awesome
THAT'S GOOD
Damn, you need 2RS bearings that are watertight, not Z or ZZ that are only dust protected.
Hi... i didn't know that about dust and watertight, but also previous old bearings was Z...
Great Advice. If something fails, don't replace it with the same part. It will only fail. I also didn't know about the difference between 2RS and Z or ZZ bearings. Good point. Fix the cause of the problem; don't just replace and repeat it. I would have made the same mistake if you hadn't mentioned it. Thank you.
oh no i got zz too, what if i slather a ton of grease?
@@difflocktwo It then sucks in tons of dirt.
is ok to apply grease inside motor magnets ? because i did
Thanks for sharing to us ,nice one especially from 11:00 good tip with welcome to circus 💪🤣😉😉
😂😁😄 Thank you mate!
Good works just wondering why didn't u use some high temp silicon on side plate b4 tighten it up to waterproof it
If the bearings overheated from the speed especially during summer times can burn all the wires can cause heated pressure even with mild explosion better have some air inside !
A hub motor is far more likely to fail from overheating than from rusting so why would anyone put an insulating seal on the motor covers which will make the motor more liekly to fail just to prevent a tiny amount of water seeping through a gap which shouldn't even be visible if screwed up properly and these droplets will usually be evaporated by the motor on the same ride anyway
@@Parabler wrong
Did you put red insulating varnish on the stator and rotor ?
what a the great design the stator for less noise I think.
what's the power?
nice work
Bro can u tell yhe size of rear motor ball bearing does 6202 size work ?
Hi buddy
Where I can get plastic spacer you install where break rotor side
I replace my bearing but I notice that I'm missing this spacer and wheel have play w shaft
I really never seen this motor, very curious about the windings. I think, it blows lot of current with little noises
Que rodamientos lleva ?
Does anybody know where I can buy a new axle for my ebike wheel, my thread has totally gone byby
I have the first version of the Crystalyte Phoenix motor. I would like to put a disk brake on it. Can it be done? Is there a replacement casing ?
*EV - Customs* 🏆🏆🏆🏆🏆🏆🏆🏆v
That plastic pipe is special adjustment does it make any heat?
8:46 i smashed soo hard but bearing does not move... and even i cracked whole case from smashing... what to do if it does not want go out?
This is a great video. My electric scooter has recently encountered a problem where the motor locks when moving forward, but it moves smoothly when moving backward, including when manually rotating. I want to know if this is because there is a problem with the bearings. The issue with the motor controller has been ruled out. Thank you, looking forward to your reply.
Why would you keep the rotor on when doing all that?
Sometimes I find a socket that's close to the O.d. of the bearing without being bigger. Then socket + wood piece + 🔨 - the batteries. I wouldn't be using the batteries as pounding blocks
So better use that last size bearings SKFon both sides looks it's fitting easy!?
Can I switch a throttle to remote ESC?
no
Γεια χαρά καλλιτέχνη μου!!🙋
Τι γνώμη έχεις για τα μονωτικά σπρέι ή βερνίκια που βάζουν στο μοτέρ (σύρμα χαλκού, μαγνήτες)..??🤔
Έχω ανοίξει τα μοτέρ μου κ δεν ξέρω αν πρέπει να ρίξω κάποιο σπρέι (ή βερνίκι μονωτικό) πριν τα ξανα κλείσω...🤷
Geia sou file... tha itan na valeis verniki... alla idiko kai oxi oti na.nai
@@EVCustoms έχεις κάποιο συγκεκριμένο..??
Να πάω να πάρω αυτό που θα μου πεις!!!
I got crystalyte H series 6.2kw
On stealth b-52 bomber
Great video! How wide is stator of that motor? What is power rating?
Rated for 5kW but fine for short burst between 8-12kW is what mine sees daily.
Where are you located? How much would you charge to refurbish a QS 205 4t motor like this?
Hello my friend... i am located in Cyprus (Greek side)
@@EVCustoms Awesome! I’m in the Santa Monica area, so not too far from ya. I’m putting a new QS205 5t on my Enduro Ebike, it’s at a motorcycle shop right now getting laced with powdercoated spokes. I’m wanting to put the old 4t onto a custom stretch cruiser sometime in the next year or so. The 4t probably needs a onceover with new bearings and the threads on the axel was in terrible condition from the previous owner, and needs swapped out or re-threaded with a die, which is why I just bought a new motor. But I want to reuse the old motor on a different bike eventually. Is this a motor a project I could work with you on?
This is the bike I’m modding and upgrading with the new motor right now
ua-cam.com/video/e0KvR8uxsEM/v-deo.html
Tak tohle je pan umělec opravař...bez lisu bez niceho..
Jesus h. Why not show where you attached the puller?
No silicon seals or gaskets only a oil seal on the Axel ( whits you poult that wiked piece of pipe truwe ) hmmmm Great jop. O and next time put a peace of whod on your tyle Floor before you beat iT whit an Axel 🤔. 😉. Ne great jop
Comment about the tiled floor was spot-on. Something protecting his electrical/electronics workbench too for heavy jobs like this, would help. Good work.
Hi... i forget on video edit to put video when i put a screw on axel before hit it on floor. ;)
Speak english
Advice from a professional.
You should have upgraded and used 2RS bearings .Rubbers seals .Oh and of you heated the end plates a bit those bearings would come out really easily.
Less drag?
@@FightFilms Whether using metal shielded or rubber sealed bearings the frictional losses are about the same .The grease does contribute a small amount to frictional losses verses a lightly oiled bearing which would not be suitable for this type of application. Always use a decent brand of bearings as the tolerance and quality control are better . Fitting a bearing correctly is essential as banging it in by the inner ring will cause damage versus pushing it in by the outer shell on a press or by means of threaded rod ,washers and nuts is the correct way.