Wow i love this trick! I wanted to change cv joints from my Ford EcoSport but was stressed how to prevent the hub from turning. Thank you very much for this video
I agree with you. Just take the center cap off of the rim. Slide it onto the rotor and then lower the vehicle with just one or two lug nuts and then the vehicle will hold everything in place so that you can just go ahead and go to town on that axle nut. 😅
The easiest way to get it off is just to take the center cap off of the rim and then put the rim back on the vehicle even if you only use a lug nut or two and then from there use an extension to get to the axle nut and if it's torqued on there like on a pickup truck you use a breaker bar and then at the end of the breaker bar you simply put the jack and you use the jack to push the breaker bar.😅
@@adamxenon829 no the actual rim. The center cap is the part where they'll put like the Mercedes emblem or the Jeep emblem you pop that part out and then put the tire back on and it gives you direct access to the nut that holds the CV axle in place in the hub
I only lower the car enough to get the wrench to just sit on the wood block. There isn’t any real heavy weight on the wrench; so I think the chances of damaging the threads is very low. Thanks for such a good question.
@@eddienolan7129 Perhaps, but in my experience I have not seen any damage to the threads. This may be due to my using the lug nuts to keep everything tight (no wiggle of the wrench). Hope this helps!
Unfortunately, the Impact gun couldn’t break the nut loose, even at 180 psi. The length of the floor jack handle provides plenty of leverage to loosen that nut.
@@spanky762is there any danger to using the impact wrench to take off an axle nut. Some people online say it can damage splines but I’ve seen it done dozens of times without issue.
Truthfully, I think if the Impact gun will work, then that is the fastest way. My issue was my impact gun did not have the power to break the axle nut loose. Using the 4 foot+ cheater bar provides so much leverage that it is easy work -it just takes a bit longer to set up.
@@spanky762 thank you. It was a genuine question. I was curious if the impact was a bad idea in this instance because I see so many tips on UA-cam for using different set ups with a breaker bar but in regular life I see impacts used on them. I know not to put one back on with any impact though. Definitely put back on using a ratchet and finishing off with a torque wrench.
But what you could have done instead. Is just put the rim back on the vehicle with the center cap removed and then you use a breaker bar with an extension. Once the vehicles back on the ground and at the end of the breaker bar you put the jack and you use the jack to rotate the breaker bar. 😅
Same here. Honda Pilot torqued to 240 ft-lb, and seized. Soaking it with PB Blaster. Broke two 1/2 inch square drives with a 3 foot extension. Haven't moved on to the torch yet. One thing, on my car a sort of collar on the nut is peened into a slot in the threads. You have to hammer it back out with a punch or the nut can't turn. But right now it is still stuck.🙁
I didn’t think I’d come to UA-cam and be saved by this handsome mug today. BIIIIG THANK YOU!!!
Wow i love this trick! I wanted to change cv joints from my Ford EcoSport but was stressed how to prevent the hub from turning. Thank you very much for this video
Take the center cap of the rim, put the parking brake and it should go like a blast.
I agree with you. Just take the center cap off of the rim. Slide it onto the rotor and then lower the vehicle with just one or two lug nuts and then the vehicle will hold everything in place so that you can just go ahead and go to town on that axle nut. 😅
I feel like a moron, for not thinking of this myself. Awesome Solution!
And if some steering wheel holder welded the axle nut to the axle?
@@9WEAVER9Cutting torch. And a stern talking to.
Bro lifesaver in 2024 on hot Alabama day. Def worked on 98 4Runner
Very nice and secure. Thanks
The easiest way to get it off is just to take the center cap off of the rim and then put the rim back on the vehicle even if you only use a lug nut or two and then from there use an extension to get to the axle nut and if it's torqued on there like on a pickup truck you use a breaker bar and then at the end of the breaker bar you simply put the jack and you use the jack to push the breaker bar.😅
HOLY CRAP! I can’t believe that did not occur to me. That is a freaking brilliant solution! Thank you! 🎉
@@spanky762 you're welcome
Your explanation doesn't make sense. What do you mean rim? The tire?
@@adamxenon829 no the actual rim. The center cap is the part where they'll put like the Mercedes emblem or the Jeep emblem you pop that part out and then put the tire back on and it gives you direct access to the nut that holds the CV axle in place in the hub
Good trick, Nice Jack.
Any danger of damaging the threads on the studs?
I only lower the car enough to get the wrench to just sit on the wood block. There isn’t any real heavy weight on the wrench; so I think the chances of damaging the threads is very low. Thanks for such a good question.
@spanky762 Ah, would there not be loads of force put on the threads though when the force of the cheater bar is applied ?
@@eddienolan7129 Perhaps, but in my experience I have not seen any damage to the threads. This may be due to my using the lug nuts to keep everything tight (no wiggle of the wrench). Hope this helps!
excellent trick, thank you
Big flathead in the rotor . Or if the parking brake works use that
Juat snapped my brand new breaker bar trying this.
How is it that I saw this comment as I JUST bought one and was about to try 💀
I just broke two 1/2 square drive wrenches doing this.
Broke my 1/2in breaker bar 😂 time to go get a bigger breaker bar!
Buy impact gun. One of the best tools to ever have.
Unfortunately, the Impact gun couldn’t break the nut loose, even at 180 psi. The length of the floor jack handle provides plenty of leverage to loosen that nut.
wow Thats very tight @@spanky762
@@spanky762is there any danger to using the impact wrench to take off an axle nut. Some people online say it can damage splines but I’ve seen it done dozens of times without issue.
Truthfully, I think if the Impact gun will work, then that is the fastest way. My issue was my impact gun did not have the power to break the axle nut loose. Using the 4 foot+ cheater bar provides so much leverage that it is easy work -it just takes a bit longer to set up.
@@spanky762 thank you. It was a genuine question. I was curious if the impact was a bad idea in this instance because I see so many tips on UA-cam for using different set ups with a breaker bar but in regular life I see impacts used on them.
I know not to put one back on with any impact though. Definitely put back on using a ratchet and finishing off with a torque wrench.
Yea we all know you can do that with a 5ft. breaker bar. I'm not sure what if anything the hocus pocus with the wrench on the lugs had to do with it.
Remove it with the tire on. Much easier
Wow wow wow. The effort on that cheater bar was nothing
The magic of leverage. :-)
Too bad my spindle nut is torqued to 241 lbs and was seized. Pb blaster, map gas torch and a whole lot of swearing and it finally came loose lol.
Yikes!
But what you could have done instead. Is just put the rim back on the vehicle with the center cap removed and then you use a breaker bar with an extension. Once the vehicles back on the ground and at the end of the breaker bar you put the jack and you use the jack to rotate the breaker bar. 😅
@gsc512 that's exactly what I did. No lift so I had to do some home mechanic gymnastics. Rust was a factor.
Same here. Honda Pilot torqued to 240 ft-lb, and seized. Soaking it with PB Blaster. Broke two 1/2 inch square drives with a 3 foot extension. Haven't moved on to the torch yet.
One thing, on my car a sort of collar on the nut is peened into a slot in the threads. You have to hammer it back out with a punch or the nut can't turn.
But right now it is still stuck.🙁