Whew - I had asked my son how I was supposed to deal with baseboard ending at an opening that has no door trim. I do like option 3 so will give it a try first.
The floor return with the mitre running through the board isn’t the best way to do it. You can still bring the mould around another way by measuring out. It’s a smaller joint and less to fill
It would have been nice if you had bothered to tell us what angle your cuts were and what you used spray the ends with before you glued them....I'm still in the dark!!
The saw is set up at 45 degrees to make a 90 degree angle. I used Miter Bond which is a CA glue, basically super glue, on one side and the spray is an activator to speed up the set time. You can use regular wood glue and hold it for a bit or tape it with some masking tape while it dries
@@BrentDarlington I'm sure that stuff will totally be OK once it arrives after being shipped from china or wherever. LOL Home depot can't even deliver this stuff a few blocks without damaging it.
Whew - I had asked my son how I was supposed to deal with baseboard ending at an opening that has no door trim. I do like option 3 so will give it a try first.
3:35 haha! Can related. ”Dont like this, prefer this but usually end up with this”
Awesome work! Now I know how to end my bathroom baseboard up to the 90° tiled wall. Thank you.
Glad I could help!
Thanks for this, was really trying to figure out how to terminate baseboard where the wall met the surface of a cabinet that was flush with the wall.
Thank you sir! Going to go with the self return
Thanks, just what I was trying to figure out!
Great tutorial, needed to see this for my own project.
Please explain the degrees used in the different cuts; more detail please. Thank you
You set the saw at 45 degrees
Absolutely great information on those cuts thank you sir
Do you need a slide saw to do these? Mine bevels both directions but it only goes up and down.
You're good with the saw you have
Those are very easy to glue with the regular glue. All you need is a bit of painters tape.
Yes
Great video!
Thanks!
I like it thanks for the great tips 👍
Would it be a good idea to back cut when base and casing are the same thickness?
I usually break the edge a bit to leave a grove where they meet.
To the point. I like it
Great vid thanks
Where do you find that glue / spray combo? I've looked in big box stores but NG. Anyone reply, I get notifications thanks.
You may have to order some online but I have seen them more and more at big box stores
What is this spray?
it speeds up the hold time for the CA glue
Super helpful thank you!!!!
Thanks!
Plinth is another option.
I'm not a fan of plinth blocks but it is an option👍
The floor return with the mitre running through the board isn’t the best way to do it. You can still bring the mould around another way by measuring out. It’s a smaller joint and less to fill
I don't understand what you mean
What's the size of the miter saw?
12"
12
He said what the first two were called but then the last one he never mentioned
I don't know if it has a specific name. I'd just call it a floor return. Hope that helps.
he went so fast I didn't catch nothing
It would have been nice if you had bothered to tell us what angle your cuts were and what you used spray the ends with before you glued them....I'm still in the dark!!
The saw is set up at 45 degrees to make a 90 degree angle. I used Miter Bond which is a CA glue, basically super glue, on one side and the spray is an activator to speed up the set time. You can use regular wood glue and hold it for a bit or tape it with some masking tape while it dries
He said every angle was 45 and it’s common sense on mitres, 45 = 90, 22.5 =45
You didnt teach the 3rd on... you just did it.
Basically the same thing, cut at 45 degrees
Wheres the info? 😂
I like to just cut it straight and then smear caulk all over the end of it🤷♂️
Do your best and caulk the rest!
I don’t smear caulk but I do spread a light coat to seal the fibers on the MDF before applying paint.
😅😅 I wish i could do that🎉
Or you can use pin nails
You can
MANUFACTURER AND EXPORTER
[ PRODUCT INTRODUCTION]
BASEBOARD/MDF WHITE MOULDING /CROWN/CASING/WAINSTCOT/QTARTERROUND
ANY INTERESTING,PLEASE CONTACT US.
no thanks, spammy
@@BrentDarlington I'm sure that stuff will totally be OK once it arrives after being shipped from china or wherever. LOL Home depot can't even deliver this stuff a few blocks without damaging it.
Showed us absolutely nothing
Thanks!
You don't explain anything
No explanation as to what angle to make the cuts..be more thorough, all the detail on the camera is with the gluing!
45 degree. Thanks for your input, noted.
Great video !!!
Thanks, glad you liked it!