I bought it to be able to upgrade for a auto bed leveling (wich need Marlin 1.1). A tip for potential buyers. If you see nothing on the lcd screen just check the usb jumper he must not be on the usb side (check this video). Tinymachines must have forgotten to turn it back when they made it flashable. No big deal but newbie like me might loose some time not finding the solution :)
This is just a how to video... they sell the boards so it just to show how to do it for people who have broken boards. To do a firmware upgrade I suspect you would just need to flash the board with the correct firmware over the ICSP port which I believe you can see there in the lower left (10 pins with a black shroud), some variants of this port art 6 pins the 10 pin port just has extra grounds if I remember correctly. I would like to see this printer get a smoothie board upgrade though!
Can I install a CR Touch with this new mother board? If so, how hard is the programming? I’m comfortable with installation of many things, but programming always gets me
0:30 You have nothing plugged on the add fan plug! This is the same as me. I had my extruder fan not moving, and thought it was because i had nothing plugged there... does your extruder fan (front fan) work?
I installed a new motherboard for the cr10. now my LCD screen shows no movement for the hot bed. Nozzle temp. works not the heated bed. Because of that the printer wont move. Is it the wrong wiring or I need a new software upgrade for the new motherboard. (I got the motherboard from Gearbest). Need help?
assembled my cr-10 today and the control box isn't turning on all connections are in place and plugged in but its not turning on lcd display is blank. even switched it onto the right voltage (110v) please help me.
having trouble getting my cr-10 to turn on out of the box havent known what to do started tinkering with the control box and power supply. Something I did while unscrewing the power supply started it up temporarily. I turned it off then tried to turn it back on to see if it was ok. Hasn't turned on since. From what I can tell the 4 minutes that it was on it was good. I have ordered a new power supply and am waiting on it. Do you think swapping the power supply will do the trick? if not what do you suggest?
Can someone help me here. I have the original single z axis cr10 and was looking to upgrade mine but this looks like he replaced an old board with another old board. Doesn't the new board have dual z connections and extra plug ins like filament sensor and other options? I was looking to buy a board on ebay. How do I know what is the correct option? I want mine to be able to add auto bed leveling abl type sensor and also have all the upgrades of the CR10S. The kits I have seen are $200 for dual z, board, lcd, and other CR10S updates. That seems a bit high when you compare the individual parts to ebay and can get them for $125 for everything. Anyone else do this? Thanks for the help.
would anyone know where to get info on why my motherboard is giving me a max temp error with the bed cool to the touch? I'm unable to clear this error and would think its a bad board
Hi Geo. I'm having the same issue on a brand new CR10. Were you able to figure this out? My research says the error is related to a bad (shorted) thermistor or fried thermistor pins on the board.
So I just stumbled across a pic of a CR-10 motherboard that has dual extruder circuits on it along with a bunch of other connections. Anyone know anything about this? pro1d5612.pic34.websiteonline.cn/upload/CrealityCR-10%2812%29.jpg
I would love some help if anybody knows, I did this board swap myself but for some reason the power supply fan and the two internal fans no longer work. I even replaced the power supply am still having the same problem. I checked all the connectors & made sure they’re on there good. I just don’t know what to do.
Thank you for caring and sharing this tutorial. It is for people like you that everything is possible through the internet
So great to see Joe Pera getting into 3D printing. Thanks for the demo!
lol
I bought it to be able to upgrade for a auto bed leveling (wich need Marlin 1.1).
A tip for potential buyers. If you see nothing on the lcd screen just check the usb jumper he must not be on the usb side (check this video). Tinymachines must have forgotten to turn it back when they made it flashable. No big deal but newbie like me might loose some time not finding the solution :)
Just got my motherboard from you, thanks for this usefull video.
Why did you swap it out? Was the original broken or is this an upgrade? Thanks for sharing this video, very detailed. :-)
This is just a how to video... they sell the boards so it just to show how to do it for people who have broken boards. To do a firmware upgrade I suspect you would just need to flash the board with the correct firmware over the ICSP port which I believe you can see there in the lower left (10 pins with a black shroud), some variants of this port art 6 pins the 10 pin port just has extra grounds if I remember correctly.
I would like to see this printer get a smoothie board upgrade though!
What is the improvement on this?
Thanks a lot a very, is a useful video
What motherboard is this? Where can I purchase it?
e? Just swap like that? No need to adjust current for each stepper driver?
Can I install a CR Touch with this new mother board? If so, how hard is the programming? I’m comfortable with installation of many things, but programming always gets me
0:30 You have nothing plugged on the add fan plug! This is the same as me. I had my extruder fan not moving, and thought it was because i had nothing plugged there... does your extruder fan (front fan) work?
Hello, didn't you check the voltage range?
I installed a new motherboard for the cr10. now my LCD screen shows no movement for the hot bed. Nozzle temp. works not the heated bed. Because of that the printer wont move. Is it the wrong wiring or I need a new software upgrade for the new motherboard. (I got the motherboard from Gearbest). Need help?
assembled my cr-10 today and the control box isn't turning on all connections are in place and plugged in but its not turning on lcd display is blank. even switched it onto the right voltage (110v) please help me.
having trouble getting my cr-10 to turn on out of the box havent known what to do started tinkering with the control box and power supply. Something I did while unscrewing the power supply started it up temporarily. I turned it off then tried to turn it back on to see if it was ok. Hasn't turned on since. From what I can tell the 4 minutes that it was on it was good. I have ordered a new power supply and am waiting on it. Do you think swapping the power supply will do the trick? if not what do you suggest?
Where can i buy the individual board to replace it, and does it have a name or serial? Thx
Do you believe we can use the board from the CR-10S Pro in the CR-10?
Can someone help me here. I have the original single z axis cr10 and was looking to upgrade mine but this looks like he replaced an old board with another old board. Doesn't the new board have dual z connections and extra plug ins like filament sensor and other options? I was looking to buy a board on ebay. How do I know what is the correct option? I want mine to be able to add auto bed leveling abl type sensor and also have all the upgrades of the CR10S. The kits I have seen are $200 for dual z, board, lcd, and other CR10S updates. That seems a bit high when you compare the individual parts to ebay and can get them for $125 for everything. Anyone else do this? Thanks for the help.
Hey guys which model motherboard is the new one and where can i buy it from? thank you in advance!!
those connectors and fets for the bed look pretty flakey.
would anyone know where to get info on why my motherboard is giving me a max temp error with the bed cool to the touch? I'm unable to clear this error and would think its a bad board
Hi Geo. I'm having the same issue on a brand new CR10. Were you able to figure this out? My research says the error is related to a bad (shorted) thermistor or fried thermistor pins on the board.
Did you get to figure the problem out?
Thanks for the video. The music is very distracting though.
Your music is way too loud, I have to turn up and turn the volume repeatedly
hi does anyone know if this is an 8bit board
So I just stumbled across a pic of a CR-10 motherboard that has dual extruder circuits on it along with a bunch of other connections. Anyone know anything about this? pro1d5612.pic34.websiteonline.cn/upload/CrealityCR-10%2812%29.jpg
The cr-10s motherboard has second extruder connection
I would love some help if anybody knows, I did this board swap myself but for some reason the power supply fan and the two internal fans no longer work. I even replaced the power supply am still having the same problem. I checked all the connectors & made sure they’re on there good. I just don’t know what to do.