hey man thank you for this very informative video I'm 99% sure my cdi box is bad I've got two cylinders not firing even with good trigger and I've searched and searched until now
CAPTAIN WILLY I was wondering if the trigger is bad would that cause the stator wires leading to the switch box to get hot and melt the plastic coating on the wires
Great video. I have no spark at all. According to my ohm meter, the regulator is bad. Will that cause no spark at every cylinder, or is my trigger likely the problem?
Great video I have the same motor question does the black and yellow cable goes to the rectifier I took the old one out and now I don't know how to connect the cables back
Love the content! Not sure where to begin but I’ve been looking forward to firing this old 105 hp Chrysler I recently found[surprisingly clean] but needs some attention.so far, I’ve rigged the ignition switch at the motor to eliminate bad wires and so forth, but still will only run for a brief second on starter fluid and only with the key in the on pos and by jumping the solenoid.Initially, I got spark on all cylinders with an in-line spark tester,but now I don’t seem to be getting spark on any cylinder. Compression is at 145-150psi. Cleaned out carburetors twice. Any tips would be appreciated! I suspect the timing may be off but I will also change the plugs is weekend and go from there since I don’t believe fuel delivery to be the issues since I’ve changed it! Thanks in advance!
Hi Captain, I have a 79 mercury 115 with no spark. I just got it. The previous owner replaced stator but not sure what else they did. I’m not sure if it’s a bad kill switch, trigger, cdi, coils etc. I see a black wire down by the cdi with tape rapped around it. Do you have a diagram or know where to get one. I’m not good with electric at all but willing to learn.
I'm getting no fire to any plugs on a 1997 Suzuki DT115 with less than a 100 hours on it. Mines turning over but its getting no fire to the plugs, from my understanding of the Factory Manual it could be the Pulsar Coil, the Trigger, the Gear Count Coil, the Stator or the CDI Unit. I wish there was a video on how to test all the different parts to know for sure what to replace.
@@JayMuzz-xn3rv It's been a while like about a year but after spending $150 for a Factory Manual I had to get the Voltage tester leads to add to my Multi-meter to test everything and it turns out it was my CDI Unit. I later found out when I let my step father use the boat for the summer he jumped the battery instead of taking it out and charging the battery and he hooked up the jumper cables wrong shorting out the CDI. So, at a $3200 new CDI replacement cost I took the motor off took the boat to a Boat Dealer and dropped $12,000 on a new Tohatsu 115 with 5 year warranty. The Suzuki is sitting in my shop today and I hope to sell it one day. I'll never buy another Susuki boat motor again.
Really enjoyed this information. How well you explained the wiring diagram. I screwed up and accidentally hook up battery wrong. What should I be looking for? Any help would be greatly appreciated.
Hey captain, I have a miss at full throttle on my 88 45 hp classic 50. I took a spark tester and I have good spark. Did you use a dva adapter on your volt meter? I ohm my stator out. The book say 5.7 to 8.0. I am reading 2.23. I guessing my stator is bad?? Any advice appreciated.
Well that sounds fun. Have you determined which cylinder is missing. Or is it all or random. If you can identify if its one or many we can go from there
I have an early '90's 175HP mercury outboard and one ear broke off the propeller (didn't hit anything) drove it back with alot of vibration for 10miles and suddenly the motor completely stopped. I have no spark anywhere now and motor wont start but turns. I did a visual inspection and no wires broke off. Had a mechanic look at it and he stated it might be a fried ECM , three wires that looked like they melted and or bad coils. (I don't think he did a well Diagnostic on the motor. While reading through the comments it looks like a bad CDI box , Stator or trigger. My worst case scenario a bad piston ring fell. I'm not that great with electrical. Any help would be appreciated
Hi nice Video,im from Germany. I have Mercury 50ps 2takt from 1992, only Spark on one Cylinder. When i change wires to coils,the Spark goes to another Cylinder. The Spark is not strong. I measure the Stator and one of wires is no passage to other wire. So the Stator must be Broken? But i hear when have Spark than it’s Not the Stator 🤷♂️ U have idea?
The stator put out a/c voltage. 4 wires. And 2 colors. While cranking check voltage in those wires. One color should have 30ish volts ac. And the other color should have over 100 volts a/c. Thats the only way to test the stator. Test with wires off of the cdi box.
The spark mived when you switched coil signal. So your coils are good. Try moving the trigger wires to another coil pole on the cdi box. Using 1 trigger to trigger the a cylinder. If you still dont have spark on the bad cylinder when you move a known good trigger. The cdi box is bad
Thanks for your fast answer I have Pictures but cant send here, from my Stator comes two yellows wires,one Black,one red and one Blue one. I messarue with Ohm,red to Black it’s 109,3 semms to be ok Blue to Black nothing,so the Stator Borken? I messuare the Trigger and all seems ok
Thtwo yellow. Not realted to spark. The black is ground. The blue and the red should have ac voltage on them. One at 30ish volts ac and the other over 100 volts ac if you dont have that check for broken wires. If none found replace stator
So I have a Merc 90hp 2002. But it does not have a CDI box. Just the rectifier. Still trying to figure out why no park. If I have no CDI box where do I look for that interchange between Stator and trigger?
Thanks! Please give me your advice. 1985 90hp Evinrude 4 cylinder. Runs rough at idle and low speed. Kicks in at mid to higher speed... One cylinder barely working at idle when plug wire pulled off while running. Things i checked...115 compression...coil swap...plug wire swapped... Fuel pump checked.. carbs swapped (2 double barrel).. sprayed carb cleaner into bad carb throat no effect but kills other side of double carb when sprayed into it.. checked spark with timing light looks like others..ran it with the plug out just blows warm air no water or fuel..plug is never very wet after running just lightly wet.. cleaned the carbs.. still not picking up that weak cylinder. Please let me know what you think. Edit... Ok i switched the power packs no change.. when i spray starting fluid in carb upper and lower it gets boggy.. also bogs when priming bulb or pushing in key for choke.
Hi,I got 332-7778 cdi switch box for 3 cylinders 2 strokes mercury force outboard 90 hp and I don’t know how to test it or diagnose my cdi switch box using multimeter?
I have a 2002 merc 75 hp 4stroke. only 2 and 4 have sparks on. 1and 3 do not have sparks. I am going to need to replace all the wires and give it another try tomorrow If I can find 804271T in stock with all the dealers here on the island. If not, I will have to wait for the eBay guy to ship to me.... If there is still a problem ( not geting sparks on 1and 3) I will hate to replace the stator and It IS a pain in the ass to get the flywheel nut off( I had to ask to plumber guy to use his ranch where he gets off the 2" pipe off) and then get a KMS tool( $30 )to take the wheel off( I think it is called a flywheel puller). Extended cranking on my bad costed me a $300 starter, another $280 for those two sets of coil wires, and I do not want to spend another $300 on the stator..... You video is good information and is helping me to regain my confidence after I lost power on the water last week..... I am from Canada but has not so fluent english writing skills.
Your writing was great. A little tip for ya. Find a big tough angry dude and a long pipe. Put the pipe on your wrench and make the big guy hold it tight on the flywheel nut. Then tap the starter. Cranking the engine should rotate the nut the right way to loosen it.
Only spark on two cylinders. Attack one at a time. Trade coil wires on the cdi box from #2 to#1. If you now have spark on #1 coils are good Put it all back. Then trade trigger wires from #1 to#2. If no spark on #2 then you need a trigger. If spark on number 2 then you need a stator. Make shur to test voltage input to the cdi from the stator
@@CAPTAINWILLY As you said, I am trying to follow your method: "Trade coil wires on the cdi box from #2 to#1. If you now have spark on #1 coils are good--> If not, the wire /and the coil is cooked? or the stator is cooked as well?. , if #1 coil is good, I move on to trading #1 to #2, if no sparks on #2, I will need a trigger? If sparks 2, then you need a stator. I mean If sparks 2, does it mean the stator is good since it pulling juice into #1? Thank you Captain and have a good night.
Yes. By trading around known good trigger wires amd get spark out of corresponding coil outputs the stator and cdi are good amd the trigger is bad. If you trade known good trigger wire amd it stays dead amd coil is already tested. Then you have a bad cdi or stator. Habe to test output voltage on stator to be shur
@@CAPTAINWILLY here's the update. I got four used coils and wires from eBay for $75. Got all sparks now. Still not starting... Is there a way to test if the trigger is good? or is the stator is good? Pls advise Capitain when you have a moment?
my 2006 90hp 2 stroke OIS ignition suddenly has no spark. IF im testing stator right MY ohms reading brown to brown 865 dva output 219, orange to orange ohms 56 dva output 4.5 im reading that on dc 600V should that be on Ac volts ?. I believe it has a sensor not a trigger. Not sure if one can create other to show no fire?? Dont mind putting some$ in to it just dont want to throw bad $ at it. Any help is appreciated
Hello there boat Community! I hope someone see’s this, I recently got into boats and motors and am trying to repair a 4 stroke merc 6hp 2007, which has been standing for about 1-2 Years. But as I dont really know too much im having some troubles, theres no spark, (already changed oil, Spark plug and gasoline) so I thought it was the Coil, so I brushed that real clean of most rust, sadly I dont have an Ohm reader to test it. My guess is that the kill switch cables are the problem though, would you have some procedures or tips to finding what my motor wants and or needs, thank you in advance. I do not have the money to let a professional look at it or buy any expensive spare parts. Have a nice day.
Guessing will be expensive. Go down to harbor freight and get a dvom. Digital voltage ohm meter. You will meed to test continuity between both wires on the kill switch in both positions. 000.= engine off postion. Open=engine run. Fair warning. Boat is an acronym. Bust out another thousand. It can be cheap but when things brake its usually at least 200 bucks... Every time
So I'm having a problem with my outboard Mercury 50 horsepower 2-stroke engine and a few people have said that they think one of my cylinders is not getting spark. Can you take a look at some videos I put up under my site and see if you think the same thing that one of my cylinders spark plugs is not getting spark. It could be any one of a number of things maybe bad fuel line, maybe bad fuel, maybe a bad pulse bulb, but I'd be curious to see if you think its cylinder issue. Let me know.
JB JB . hey there. I just watched all of your videos. Yes. Deffently a spark issue. Heres what im going to recommend. Write this down. 1. Get the problem to happen when running 2. While problem is happing take some needle nose plyers amd remove each spark plug wire one at a time. 3. If the engine dies or runs much worse. Them that plug is not an issue. 4. Continue for the rest of the plugs until removing a wire dosnt change the condition. 5. While it hasnt changed the condition amd the wire is off hold it close to the end of the plug or the block or a ground amd see if a spark jumps from the wire to ground. 6. Contact me.
CAPTAIN WILLY'S FISHING ADVENTURES okay got it the only other thing I wanted to add is that the engine seems to have an easier time starting when it's in an upright position rather than all trimmed all the way down I'm not sure if that's an indication that it's more carburetor related or not but I thought I would let you know. I really have no idea what it could be one when I feel like I finally have narrowed it down something will happen that will make me completely rethink whether I have the correct answer or not so I'm really just Flying Blind here trying to figure this out.
CAPTAIN WILLY'S FISHING ADVENTURES Okay so went out and purchased and inline spark tester and put it on all three and all three had an excellent spark. So I don't think it's a cylinder. If it helps any - when I first started the boat after not touching it for a week it started up perfect Idol perfect no problems at all it sounded like a new boat then it slowly deteriorated after about 10 minutes. Then it stalled and then I couldn't start it for about 10 minutes. So I'm not sure if that's indicative of a carburetor or not but that's what it did today anyway. It's worth mentioning that I also went out and purchased a $30 Mercury pulse bulb and put that on in replacement of the old one in hopes that it would help but it didn't seem to make a difference.
Negative....I would just connect the inline spark tester , start the engine, walk to the back of the boat and check the tester. i did this for all three spark plugs and that was it. Did I do it incorrectly? Should I have waited for the engine to start acting up? I just figured that as long there was a good spark there then that was not the problem. Let me know what you think.
My motor is turning over but no spark on any cylinders I have 2 stroke 4 cylinder merc mariner 40hp. What could it be replaced stator switch box battery spark plugs what else?
There’s three wires on top of my 115 hp evinrude cut wires a purple one gray one and a black one I can’t find where they go I think there trigger wires
CAPTAIN WILLY 1974 115 evinrude I think there trigger wires but I can’t find where they go they look cut just laying on the back of flywheel under it sort of in a taped up harness
Help!! So, I was only running on 2 cyl and after new plugs, wires, coils, trigger, and stator I'm getting nothing now just cranks, before it would start and run but now just cranks?
Gez that sounds like alot of money. Fist step: spray some starting fluid in the carb and verify thhis isnt a fuel problem. Then buy a spark tester to put inline with a plug wire
Yes it was a lot of money..lol but my guess is I wired something backwards. I can't find diagram that has color. I've switched some around but my brain is wore out.
I have the same issue with not having any spark. How did you figure out it was a bad piston ring? My motor spins but no spark. I drove my boat with one broken ear on the propeller and with all that vibration, I might have lost a piston ring too
I have a 1980 mercury 50 4 cylinder with only 1 cylinder with spark which is the second one from the top I need help on how to test the Cdi box do I use a volt meter or what I think it may be the coil but not sure NEED HELP THANKS
Colby Zern. So yes a multimeter will be needed. Sence you have one cylinder that has spark. Use That to your advantage. Follow your wires for identification. Coil wires. Stator wires. And trigger wires. Trigger wires will be between the coil wires. Swap the coil wires on the cdi. You said spark on two. So use the coil output on the cdi box to test other coils. Hooking up coil 3 on the coil 2 spot if coil 3 sparks then coils are good. Next test trigger. Swap trigger for 3 onto number 2 post on the cdi. This is testing the trigger. Like having one good post on the cdi. Test multible parts with that post.
Okay so i did that. we tried a lot of things but then we found that the spark plug wires are corroded so i cleaned them up and we know have spark on 3 cylinders so we are going to try to replace the top cylinder coil and pray that it works thanks ill let you know.
I know this is a bit of an ask .but would you be able to help me locate some Information. Regarding the wire diagram for the starter / ignition switches .also would you know the correct part number for the trigger as I'm struggling for a spark
If there is ac voltage from the stator like i said in the video. Yet no spark anywhere. You need to test resistance across the trigger. Depending on how many trigger wires you have/ cylinders you have. There are lots of videos how to test a trigger. But its likly a bad cdi box. Usually when a trigger fails its only on one cylinder or two. Total loss of spark is more like the cdi. Only replace it if the trigger tests good
I just fixed my Johnson 110. It would run great when cold but when it was warmed it would run like crap. Hard warm start. Had air, fuel and compression was 115 across the board. It was the power pack. Replaced and now she hits 32 mph on 20ft chapperal at 5100 rpms
Ok little confused.. you said the stater is to convert A/c to D/c to charge batt. Then you said the stater was to give the power pack charge. Will a motor start if there is a bad stater? And what about rectifier, will motor still start with bad rectifier?
Ok sorry. There are two winding in a stator. One the powers the cdi for spark. And another that feeds the rectifier. Then power gos from rectifier to battery. Bad rectifier engine will run with no battery charge. Bad stator on the cdi side no start. Bad stator on the rectifier side will start.
@@CAPTAINWILLY Thank you! It did finally attempt to start and when it did I noticed the flywheel changed direction to counter clockwise not sure why Maybe I have the stator on wrong I need to rotate it one bolt hole IDK you have any idea? And there is only 2wires coming out of stator I don’t think I got them hooked up wrong. Working on 1979 Mariner 115hp in line 6 tower of power. When I try to start it flywheel is rotating clockwise (normal) rotation I believe, then when it attempts to fire up flywheel changes direction. Haven’t ran it that way don’t want to miss it up.
![HOW TO TEST A STATOR / WHAT IS A STATOR [step by step] GY6](/img/n.gif)
hey man thank you for this very informative video I'm 99% sure my cdi box is bad I've got two cylinders not firing even with good trigger and I've searched and searched until now
I don't know how to explain it, but for some reason I want to subscribe.
Let er rip brotha
You have some of the best videos out there on this man thank you
Thanks brotha. Please share it on your socials
CAPTAIN WILLY I was wondering if the trigger is bad would that cause the stator wires leading to the switch box to get hot and melt the plastic coating on the wires
I just shared it as well
Great video and explanation!!
Great video. I have no spark at all. According to my ohm meter, the regulator is bad. Will that cause no spark at every cylinder, or is my trigger likely the problem?
Great video I have no spark do you have the parts numbers for stator trigger and rectifier? For this motor I have the same one
Love the bee-dee ba-dah sound effects
Great video I have the same motor question does the black and yellow cable goes to the rectifier I took the old one out and now I don't know how to connect the cables back
Love the content! Not sure where to begin but I’ve been looking forward to firing this old 105 hp Chrysler I recently found[surprisingly clean] but needs some attention.so far, I’ve rigged the ignition switch at the motor to eliminate bad wires and so forth, but still will only run for a brief second on starter fluid and only with the key in the on pos and by jumping the solenoid.Initially, I got spark on all cylinders with an in-line spark tester,but now I don’t seem to be getting spark on any cylinder. Compression is at 145-150psi. Cleaned out carburetors twice. Any tips would be appreciated! I suspect the timing may be off but I will also change the plugs is weekend and go from there since I don’t believe fuel delivery to be the issues since I’ve changed it! Thanks in advance!
Man this helped me fix my 68 chrystler with no spark to either coil my man !
Thanks brotha. Dont forget to share and sub
Hi Captain, I have a 79 mercury 115 with no spark. I just got it. The previous owner replaced stator but not sure what else they did. I’m not sure if it’s a bad kill switch, trigger, cdi, coils etc. I see a black wire down by the cdi with tape rapped around it. Do you have a diagram or know where to get one. I’m not good with electric at all but willing to learn.
fabulous. good back engineering diagnosis. my service peeps still can't find what's giving my 4 stroke Honda 7.5hp an unreliable spark...
Kill switch more times than not
Lmao the sound affects im subscribing
Thanks brotha
Broken down perfectly! Thank you!
Nice troubleshoot and funny too. Longwinded? Naw. keep it up !
really really good information. thank you for posting!
I'm getting no fire to any plugs on a 1997 Suzuki DT115 with less than a 100 hours on it. Mines turning over but its getting no fire to the plugs, from my understanding of the Factory Manual it could be the Pulsar Coil, the Trigger, the Gear Count Coil, the Stator or the CDI Unit. I wish there was a video on how to test all the different parts to know for sure what to replace.
I’m here today with same issue as you describe
@@JayMuzz-xn3rv It's been a while like about a year but after spending $150 for a Factory Manual I had to get the Voltage tester leads to add to my Multi-meter to test everything and it turns out it was my CDI Unit. I later found out when I let my step father use the boat for the summer he jumped the battery instead of taking it out and charging the battery and he hooked up the jumper cables wrong shorting out the CDI. So, at a $3200 new CDI replacement cost I took the motor off took the boat to a Boat Dealer and dropped $12,000 on a new Tohatsu 115 with 5 year warranty. The Suzuki is sitting in my shop today and I hope to sell it one day. I'll never buy another Susuki boat motor again.
How many cables go connected to the rectifier I can really use your help
Really enjoyed this information. How well you explained the wiring diagram. I screwed up and accidentally hook up battery wrong. What should I be looking for? Any help would be greatly appreciated.
You made a nice video
Great information. Thank you
Thanks brotha. Dont forget to share and sub
I may have missed it, but WHAT Merc outboard was that you were working on? What year?
Awsome info mate!
Well done willy
Hey captain, I have a miss at full throttle on my 88 45 hp classic 50. I took a spark tester and I have good spark. Did you use a dva adapter on your volt meter? I ohm my stator out. The book say 5.7 to 8.0. I am reading 2.23. I guessing my stator is bad?? Any advice appreciated.
Well that sounds fun.
Have you determined which cylinder is missing. Or is it all or random. If you can identify if its one or many we can go from there
I have an early '90's 175HP mercury outboard and one ear broke off the propeller (didn't hit anything) drove it back with alot of vibration for 10miles and suddenly the motor completely stopped. I have no spark anywhere now and motor wont start but turns. I did a visual inspection and no wires broke off. Had a mechanic look at it and he stated it might be a fried ECM , three wires that looked like they melted and or bad coils. (I don't think he did a well Diagnostic on the motor.
While reading through the comments it looks like a bad CDI box , Stator or trigger.
My worst case scenario a bad piston ring fell. I'm not that great with electrical. Any help would be appreciated
Hi nice Video,im from Germany.
I have Mercury 50ps 2takt from 1992, only Spark on one Cylinder.
When i change wires to coils,the Spark goes to another Cylinder.
The Spark is not strong.
I measure the Stator and one of wires is no passage to other wire.
So the Stator must be Broken?
But i hear when have Spark than it’s Not the Stator 🤷♂️
U have idea?
The stator put out a/c voltage. 4 wires. And 2 colors. While cranking check voltage in those wires. One color should have 30ish volts ac. And the other color should have over 100 volts a/c. Thats the only way to test the stator. Test with wires off of the cdi box.
The spark mived when you switched coil signal. So your coils are good. Try moving the trigger wires to another coil pole on the cdi box. Using 1 trigger to trigger the a cylinder. If you still dont have spark on the bad cylinder when you move a known good trigger. The cdi box is bad
Thanks for your fast answer
I have Pictures but cant send here, from my Stator comes two yellows wires,one Black,one red and one Blue one.
I messarue with Ohm,red to Black it’s 109,3 semms to be ok
Blue to Black nothing,so the Stator Borken?
I messuare the Trigger and all seems ok
Before i had Problems mit the Gastank so i Start many times without Gas and wohnt start.
Maybe something Burns up?
Thtwo yellow. Not realted to spark. The black is ground. The blue and the red should have ac voltage on them. One at 30ish volts ac and the other over 100 volts ac if you dont have that check for broken wires. If none found replace stator
So I have a Merc 90hp 2002. But it does not have a CDI box. Just the rectifier. Still trying to figure out why no park. If I have no CDI box where do I look for that interchange between Stator and trigger?
Thanks! Please give me your advice. 1985 90hp Evinrude 4 cylinder. Runs rough at idle and low speed. Kicks in at mid to higher speed... One cylinder barely working at idle when plug wire pulled off while running. Things i checked...115 compression...coil swap...plug wire swapped... Fuel pump checked.. carbs swapped (2 double barrel).. sprayed carb cleaner into bad carb throat no effect but kills other side of double carb when sprayed into it.. checked spark with timing light looks like others..ran it with the plug out just blows warm air no water or fuel..plug is never very wet after running just lightly wet.. cleaned the carbs.. still not picking up that weak cylinder. Please let me know what you think. Edit... Ok i switched the power packs no change.. when i spray starting fluid in carb upper and lower it gets boggy.. also bogs when priming bulb or pushing in key for choke.
By the way this motor has one power pack per side. Thought about swapping them but timing light showed ok.
Excellent vid!
Thanks!
Your welcome brother! Thankyou!
Hi,I got 332-7778 cdi switch box for 3 cylinders 2 strokes mercury force outboard 90 hp and I don’t know how to test it or diagnose my cdi switch box using multimeter?
If trigger is bad would that cause stator wires to get hot and melt the plastic
Yes. And or the cdi box. If there is any short to ground. It will cause melted wires. Iv even seen a coil cause it
I have a 2002 merc 75 hp 4stroke. only 2 and 4 have sparks on. 1and 3 do not have sparks. I am going to need to replace all the wires and give it another try tomorrow If I can find 804271T in stock with all the dealers here on the island. If not, I will have to wait for the eBay guy to ship to me.... If there is still a problem ( not geting sparks on 1and 3) I will hate to replace the stator and It IS a pain in the ass to get the flywheel nut off( I had to ask to plumber guy to use his ranch where he gets off the 2" pipe off) and then get a KMS tool( $30 )to take the wheel off( I think it is called a flywheel puller). Extended cranking on my bad costed me a $300 starter, another $280 for those two sets of coil wires, and I do not want to spend another $300 on the stator..... You video is good information and is helping me to regain my confidence after I lost power on the water last week..... I am from Canada but has not so fluent english writing skills.
Your writing was great. A little tip for ya. Find a big tough angry dude and a long pipe. Put the pipe on your wrench and make the big guy hold it tight on the flywheel nut. Then tap the starter. Cranking the engine should rotate the nut the right way to loosen it.
Only spark on two cylinders.
Attack one at a time. Trade coil wires on the cdi box from #2 to#1. If you now have spark on #1 coils are good
Put it all back.
Then trade trigger wires from #1 to#2. If no spark on #2 then you need a trigger. If spark on number 2 then you need a stator. Make shur to test voltage input to the cdi from the stator
@@CAPTAINWILLY As you said, I am trying to follow your method: "Trade coil wires on the cdi box from #2 to#1. If you now have spark on #1 coils are good--> If not, the wire /and the coil is cooked? or the stator is cooked as well?. , if #1 coil is good, I move on to trading #1 to #2, if no sparks on #2, I will need a trigger? If sparks 2, then you need a stator. I mean If sparks 2, does it mean the stator is good since it pulling juice into #1? Thank you Captain and have a good night.
Yes. By trading around known good trigger wires amd get spark out of corresponding coil outputs the stator and cdi are good amd the trigger is bad. If you trade known good trigger wire amd it stays dead amd coil is already tested. Then you have a bad cdi or stator. Habe to test output voltage on stator to be shur
@@CAPTAINWILLY here's the update. I got four used coils and wires from eBay for $75. Got all sparks now. Still not starting... Is there a way to test if the trigger is good? or is the stator is good? Pls advise Capitain when you have a moment?
my 2006 90hp 2 stroke OIS ignition suddenly has no spark. IF im testing stator right MY ohms reading brown to brown 865 dva output 219, orange to orange ohms 56 dva output 4.5 im reading that on dc 600V should that be on Ac volts ?. I believe it has a sensor not a trigger. Not sure if one can create other to show no fire?? Dont mind putting some$ in to it just dont want to throw bad $ at it. Any help is appreciated
Cool video great info 🤙😎
Question. Only one trigger wire broke how is it missing on two cylinders??
After removing the upper shrouds there was 2 broken wires
Thank you!
Hello there boat Community!
I hope someone see’s this, I recently got into boats and motors and am trying to repair a 4 stroke merc 6hp 2007, which has been standing for about 1-2 Years.
But as I dont really know too much im having some troubles, theres no spark, (already changed oil, Spark plug and gasoline) so I thought it was the Coil, so I brushed that real clean of most rust, sadly I dont have an Ohm reader to test it.
My guess is that the kill switch cables are the problem though, would you have some procedures or tips to finding what my motor wants and or needs, thank you in advance. I do not have the money to let a professional look at it or buy any expensive spare parts.
Have a nice day.
Guessing will be expensive. Go down to harbor freight and get a dvom. Digital voltage ohm meter. You will meed to test continuity between both wires on the kill switch in both positions. 000.= engine off postion. Open=engine run.
Fair warning. Boat is an acronym. Bust out another thousand. It can be cheap but when things brake its usually at least 200 bucks... Every time
CAPTAIN WILLY Thank you for the advice I will try to get one as soon as possible as well as test it out! 😄
I’ll keep you posted If I make progress!
Goodjob
So I'm having a problem with my outboard Mercury 50 horsepower 2-stroke engine and a few people have said that they think one of my cylinders is not getting spark.
Can you take a look at some videos I put up under my site and see if you think the same thing that one of my cylinders spark plugs is not getting spark.
It could be any one of a number of things maybe bad fuel line, maybe bad fuel, maybe a bad pulse bulb, but I'd be curious to see if you think its cylinder issue.
Let me know.
JB JB . hey there. I just watched all of your videos. Yes. Deffently a spark issue. Heres what im going to recommend.
Write this down.
1. Get the problem to happen when running
2. While problem is happing take some needle nose plyers amd remove each spark plug wire one at a time.
3. If the engine dies or runs much worse. Them that plug is not an issue.
4. Continue for the rest of the plugs until removing a wire dosnt change the condition.
5. While it hasnt changed the condition amd the wire is off hold it close to the end of the plug or the block or a ground amd see if a spark jumps from the wire to ground.
6. Contact me.
CAPTAIN WILLY'S FISHING ADVENTURES okay got it the only other thing I wanted to add is that the engine seems to have an easier time starting when it's in an upright position rather than all trimmed all the way down I'm not sure if that's an indication that it's more carburetor related or not but I thought I would let you know.
I really have no idea what it could be one when I feel like I finally have narrowed it down something will happen that will make me completely rethink whether I have the correct answer or not so I'm really just Flying Blind here trying to figure this out.
CAPTAIN WILLY'S FISHING ADVENTURES Okay so went out and purchased and inline spark tester and put it on all three and all three had an excellent spark.
So I don't think it's a cylinder. If it helps any - when I first started the boat after not touching it for a week it started up perfect Idol perfect no problems at all it sounded like a new boat then it slowly deteriorated after about 10 minutes. Then it stalled and then I couldn't start it for about 10 minutes. So I'm not sure if that's indicative of a carburetor or not but that's what it did today anyway.
It's worth mentioning that I also went out and purchased a $30 Mercury pulse bulb and put that on in replacement of the old one in hopes that it would help but it didn't seem to make a difference.
JB JB did you test the spark again after it started to deteriorate after the 10 minutes?
Negative....I would just connect the inline spark tester , start the engine, walk to the back of the boat and check the tester. i did this for all three spark plugs and that was it.
Did I do it incorrectly? Should I have waited for the engine to start acting up? I just figured that as long there was a good spark there then that was not the problem.
Let me know what you think.
Bad stator or bad trigger
My motor is turning over but no spark on any cylinders I have 2 stroke 4 cylinder merc mariner 40hp. What could it be replaced stator switch box battery spark plugs what else?
I have the same issue. No spark anywherr..anywhere... have you figured out your issue?
@@Diego-le5xt I think my new stator was no good have you changed your stator? About to try a new one I'll let you know once I try that if you want...
@@robpaul7900 yes let me know. Thank you
seedy eye box
There’s three wires on top of my 115 hp evinrude cut wires a purple one gray one and a black one I can’t find where they go I think there trigger wires
What yearish? 2 stroke? How many cylinders?
CAPTAIN WILLY 1974 115 evinrude I think there trigger wires but I can’t find where they go they look cut just laying on the back of flywheel under it sort of in a taped up harness
CAPTAIN WILLY 4 cylinders
I need help with my motor just bought a boat. No spark on any piston
You need to test ac voltage from your stator while cranking first
I had that problem, and it was the safety switch
Lucas Hunter hey I got one cylinder not firing, I have done all the trying different wires and it works on different wires, would it be the stator ?
I don’t know man are you sure that’s on an engine?.... kinda looks like the inside of a power utility box...
SS Maynerd hehe. Totally!
Uhu
Help!! So, I was only running on 2 cyl and after new plugs, wires, coils, trigger, and stator I'm getting nothing now just cranks, before it would start and run but now just cranks?
Gez that sounds like alot of money. Fist step: spray some starting fluid in the carb and verify thhis isnt a fuel problem. Then buy a spark tester to put inline with a plug wire
@@CAPTAINWILLY well the fuel is what I tested before the spark problem. I did an inline test no spark on any
Yes it was a lot of money..lol but my guess is I wired something backwards. I can't find diagram that has color. I've switched some around but my brain is wore out.
Update: End up being a piston ring dropped lost compression.
I have the same issue with not having any spark. How did you figure out it was a bad piston ring? My motor spins but no spark. I drove my boat with one broken ear on the propeller and with all that vibration, I might have lost a piston ring too
I have a 1980 mercury 50 4 cylinder with only 1 cylinder with spark which is the second one from the top I need help on how to test the Cdi box do I use a volt meter or what I think it may be the coil but not sure NEED HELP THANKS
Colby Zern. So yes a multimeter will be needed. Sence you have one cylinder that has spark. Use That to your advantage. Follow your wires for identification. Coil wires. Stator wires. And trigger wires. Trigger wires will be between the coil wires.
Swap the coil wires on the cdi. You said spark on two. So use the coil output on the cdi box to test other coils.
Hooking up coil 3 on the coil 2 spot if coil 3 sparks then coils are good.
Next test trigger. Swap trigger for 3 onto number 2 post on the cdi. This is testing the trigger. Like having one good post on the cdi. Test multible parts with that post.
Okay so i did that. we tried a lot of things but then we found that the spark plug wires are corroded so i cleaned them up and we know have spark on 3 cylinders so we are going to try to replace the top cylinder coil and pray that it works thanks ill let you know.
What's with the um,um business?? Get with it!!
Well said eddie. Im working on it. My channel is slowly improving.... If you were a subscriber...you would know
@@CAPTAINWILLY Very informative video....thank u!!
Ha ha ha, clear as mud
But thank you for the post buddy, I appreciate it man
Don you still own this engine bud .I'm from the UK and nobody over hear knows a thing about theses
I have one just like it yes
I know this is a bit of an ask .but would you be able to help me locate some Information. Regarding the wire diagram for the starter / ignition switches .also would you know the correct part number for the trigger as I'm struggling for a spark
Marine engine.com will have alot of that info.
Hey. My mercury has absolutely no spark. I am getting power to the box.
How many cylinders what year or year ish.
No spark on any cylinder? And you have ac voltage on all stator wires?
If there is ac voltage from the stator like i said in the video. Yet no spark anywhere. You need to test resistance across the trigger. Depending on how many trigger wires you have/ cylinders you have. There are lots of videos how to test a trigger. But its likly a bad cdi box. Usually when a trigger fails its only on one cylinder or two. Total loss of spark is more like the cdi. Only replace it if the trigger tests good
89
3 cyl
Around here 95% of the ones iv worked on cdi or power c
Pack bad my merc 90hp stop firing one #1 power pack
I just fixed my Johnson 110. It would run great when cold but when it was warmed it would run like crap. Hard warm start. Had air, fuel and compression was 115 across the board. It was the power pack. Replaced and now she hits 32 mph on 20ft chapperal at 5100 rpms
Ok little confused.. you said the stater is to convert A/c to D/c to charge batt. Then you said the stater was to give the power pack charge. Will a motor start if there is a bad stater? And what about rectifier, will motor still start with bad rectifier?
Ok sorry. There are two winding in a stator. One the powers the cdi for spark. And another that feeds the rectifier. Then power gos from rectifier to battery. Bad rectifier engine will run with no battery charge. Bad stator on the cdi side no start. Bad stator on the rectifier side will start.
@@CAPTAINWILLY Thank you!
It did finally attempt to start and when it did I noticed the flywheel changed direction to counter clockwise not sure why Maybe I have the stator on wrong I need to rotate it one bolt hole IDK you have any idea? And there is only 2wires coming out of stator I don’t think I got them hooked up wrong.
Working on 1979 Mariner 115hp in line 6 tower of power.
When I try to start it flywheel is rotating clockwise (normal) rotation I believe, then when it attempts to fire up flywheel changes direction. Haven’t ran it that way don’t want to miss it up.
Thanks!