The last shot of the helmet was a HUGE surprise! In addition to being a firefighter/paramedic, I am also a Medical Examiner.. I instantly recognized the helmet by the shield on the front of it; because, I was the Medical Examiner on a fatal wreck where the owner of that helmet was on KFD Truck 41, literally two nights ago! 🤯 Perfect example of a small world! Also, great job on the helmet, it looked great!
One Shot was the approved “touch up” paint recommended by cairns in the Pre-MSA days. I am almost sure that was the paint used to produce the helmets while in NJ.
I have buddies on my snap they are volunteer fire fighters they risk there lives for 0 pay THANKS FIREFIGHTERS,POLICE,EMS,MILITARY,ALL HEROS KEEPING US SAFE AND ALSO THANK A FARMER AND TRUCKER WHO PROVIDES AND TRANSPORTS ALL OF THE SUPPLIES AND FOOD
Could you also thin this paint with mineral spirits? If so would there be any downside other than maybe more time to dry? I’m about to do the same job you did once I finish some other repairs to the helmet
Not really sure, the stuff I used came fro Tractor Supply and it’s an enamel reducer. One Shot is an enamel paint. You could try a test spot, however the reducer I used was very inexpensive. Thanks for watching and good luck on your project!
Thank you! I needed up heading to TSC and got the same stuff. I used your recommendation of “little thicker than milk” since I’ve never used enamel paint or a spray gun for that matter, and it turned out GREAT! It looks just like the one you shot and I’m a total beginner. Thanks for the tips and great tutorial
I’ve been mixing paint for years, lol. Didn’t really have a proper ratio. If you’re using the cheap purple harbor freight gun just mix it to the consistency a tad thicker than milk. You want it to flow well, it won’t lay smooth at first but as it dries it should level out a bit. Spray it in light coats. Hopes this helps, best of luck.
Glaze is a product that’s used auto body repair. Usually a two part product, one will be glaze the other is activator or hardener you mix in. Then you spread it, let it dry then sand it to a smooth finish then prime and paint. Clearcoat is another product you spray last to give a lasting shine and uv protection. Hope that helps! Thanks for watching
Oh man, it’s been so long lol. I usually mix stuff up to the consistency of milk, 😂. I’ll thin some down this weekend and see if can get ya a better idea!
If I want to put a new crown and eagle on my helmet, how would I do that? Also, if I wanted to replace the ear flaps in my helmet, is that a possibility? For reference, it’s an 85’ N5A
definitely possible for crown and eagle the liner and ear flaps tho is possible but very tricky you'd be better off sending it to someone like capital city or rekindled lids to have that done
Ok so one shot is a thick paint so you need to thin ( this will sound crazy) to the consistency of a lil thicker than milk. I used the purple harbor freight gun so I wouldn’t possibly contaminate my good guns. The purple gun will do a good job, if it’s to thick and sputters just add a lil more thinner. Just to let ya know the helmet is holding up great! Let me know if have any more questions. Thanks for watching
@@markjackson812 no I only used maybe a quarter of the can. If you’re gonna prime like I did with the trans tar you can get it in black. That way you would need less paint to cover it.
The last shot of the helmet was a HUGE surprise! In addition to being a firefighter/paramedic, I am also a Medical Examiner.. I instantly recognized the helmet by the shield on the front of it; because, I was the Medical Examiner on a fatal wreck where the owner of that helmet was on KFD Truck 41, literally two nights ago! 🤯 Perfect example of a small world! Also, great job on the helmet, it looked great!
Thanks,appreciate ya viewing,commenting and subscribing!!
One Shot was the approved “touch up” paint recommended by cairns in the Pre-MSA days. I am almost sure that was the paint used to produce the helmets while in NJ.
Wow good to know. I’ve used one shot before so I thought it would hold up nicely. So far it has. Thanks for watching and commenting!!
well sprayed and well spoken Sir : )
Once again, thanks brother
Great video. And awesome looking helmet.
Thanks a lot, I have several friends that are first responders!! Let’s thank them also!!
I have buddies on my snap they are volunteer fire fighters they risk there lives for 0 pay THANKS FIREFIGHTERS,POLICE,EMS,MILITARY,ALL HEROS KEEPING US SAFE AND ALSO THANK A FARMER AND TRUCKER WHO PROVIDES AND TRANSPORTS ALL OF THE SUPPLIES AND FOOD
Very true, I have hauled soy beans for a good friend of mine, Freightliner and a 40ft dump trailer
Thanks for watching!
Could you also thin this paint with mineral spirits? If so would there be any downside other than maybe more time to dry? I’m about to do the same job you did once I finish some other repairs to the helmet
Not really sure, the stuff I used came fro Tractor Supply and it’s an enamel reducer. One Shot is an enamel paint. You could try a test spot, however the reducer I used was very inexpensive. Thanks for watching and good luck on your project!
Thank you! I needed up heading to TSC and got the same stuff. I used your recommendation of “little thicker than milk” since I’ve never used enamel paint or a spray gun for that matter, and it turned out GREAT! It looks just like the one you shot and I’m a total beginner. Thanks for the tips and great tutorial
@@travisscottmedina yes sir glad I could help!
Can you give us the proper ratio of paint to thinner when mixing for an HVLP gun?
I’ve been mixing paint for years, lol. Didn’t really have a proper ratio. If you’re using the cheap purple harbor freight gun just mix it to the consistency a tad thicker than milk. You want it to flow well, it won’t lay smooth at first but as it dries it should level out a bit. Spray it in light coats. Hopes this helps, best of luck.
What did you mean by glaze? Clearcoat? If so what do you recommend
Glaze is a product that’s used auto body repair. Usually a two part product, one will be glaze the other is activator or hardener you mix in. Then you spread it, let it dry then sand it to a smooth finish then prime and paint. Clearcoat is another product you spray last to give a lasting shine and uv protection. Hope that helps! Thanks for watching
what’s the ratio you thinned the paint at? looks really good better than brushing on
Oh man, it’s been so long lol. I usually mix stuff up to the consistency of milk, 😂. I’ll thin some down this weekend and see if can get ya a better idea!
If I want to put a new crown and eagle on my helmet, how would I do that? Also, if I wanted to replace the ear flaps in my helmet, is that a possibility? For reference, it’s an 85’ N5A
Not exactly sure. I’ve only painted that one for a good friend. I’ll look at another helmet and see if I can come up with anything.
definitely possible for crown and eagle the liner and ear flaps tho is possible but very tricky you'd be better off sending it to someone like capital city or rekindled lids to have that done
Cool
Thanks for watching!!
What paint and primer did you use?
The primer was Transtar 2n1,and the paint was One Shot lettering enamel
@@speedy94- thank you!
👍
How has it held up so far? I just bought an N5A and am about to do the same thing lol
Still looks like it was freshly painted!
Thanks for watching and commenting
What ratio did you thin it down to?
Ok so one shot is a thick paint so you need to thin ( this will sound crazy) to the consistency of a lil thicker than milk. I used the purple harbor freight gun so I wouldn’t possibly contaminate my good guns. The purple gun will do a good job, if it’s to thick and sputters just add a lil more thinner. Just to let ya know the helmet is holding up great! Let me know if have any more questions. Thanks for watching
Did you use a full can of one shot? How much thinner did you use?
@@markjackson812 no I only used maybe a quarter of the can. If you’re gonna prime like I did with the trans tar you can get it in black. That way you would need less paint to cover it.
What about a Tl2?
??