On each valve (which the solenoid is on) is a little round knob. Turn the round knob counter clockwise to open that valve. Now go check to see which sprinklers are on. This will tell you which valve goes for which system of sprinklers in your yard.
Do I need to shut off the entire house power to swap out wires on solenoids when I replace anti-siphon valves or just the controller sprinkler system to be in off mode? I want to avoid getting electrocuted.
Gregory, thanks for pointing out to watch out for the old O ring. It was left behind when I replaced the solenoid and the new one would not shut off as a result. Luckily I read thru the comments here and was able to figure out the problem.
some replacement solenoids have a small white guard around the plunger - should this be removed before installation? I do not see one in the picture on the solenoid.
How do you know which solenoid goes with what zone on your system? We don't have just one control box we have about 4 of the small round control boxes spread about the front & back yard. Some have just one solenoid & others have 2. =/
One of my zones stays on slightly after the scheduled time while my other timed zones are sprinkling. Would this be a problem where that zone solenoid needs to be replaced?
That is great for the value in the video, but what if you have the type of valve that has the solenoid on the side and the adjustment in the center? Like this one: 3/4"FPT Auto Inline Valve With Flow Control
have replaced the solenoids and it hasn't fixed the problem, I have 3 valves and the middle one isn't turning itself on with the timer...its making the sounds at the valve box, but not coming on
+Bob Gaddis it could be multiple things bob, If your system has been winterized its very possible that the bleed screw has been turn on which totally bypasses what the solenoid is meant to do. Make sure its off and if that fails make sure the timer isnt running on its own. Also the solenoid might not be fully shut which means you might have to try and rotate the solenoid clockwise to tighten it. If all these steps are not working then you're looking at a solenoid problem.
yes,but be sure you dont tighten too tight because you can stretch the o-ring and the valve wont shut off. hope that helps.oh and the little handle comes off,basically the same procedure,the wires can be reversed
I have a problem. My rainbird controller fuse blows off when it gets to zone 5 out of 7 zones. When i turn the zone 5 to 00 running time, it skips the zone 5 and works fine all the way to zone 7. I am guessing that there is some electric issue with zone 5 valve. Any suggestions?? replace valve or replace solenoid or what???
I've changed out my solenoid and now it's making a hissing noise if I turn it a bit as if I was treating it Manuelie it stops but it still releases water what is the problem
this could be a number of things. we'd need to speak with you and try some different fixes to determine the problem. Please send your contact info via private message to our social media and we'll get in touch. Thanks.
+SpectreRSG It's called a multi-purpose electrician's tool. It cuts and strips wire, trims bolts to length, crimps connectors, and more. Here is one: www.altex.com/Klein-Tools-Combination-Wire-Stripper-Cutter-Multi-Purpose-Electricians-Tool-1001-P143496.aspx
you have infinite resistance on that zone,go to your timer find what color the wire is and referance it back to your valve box,or test your silinoids with a volt meter,turn to ohms and if it goes to zero your silinoid needs to be replaced
Hi Jason, Is there a way to test the solinoids without having to cutting all the wires and then using a voltmeter to find the faulty solinoid. i.e any way of testing to see which one is faulty first.
+John Smith The solenoid allows the valve to turn on when power is sent from the common wire and the zone wire. Without one the valve wouldn't be able to turn on via the timer.
Next to each valve (which the solenoid is on) is a little round knob. Turn the round knob counter clockwise to open that valve. Now go check to see which sprinklers are on. This will tell you which valve goes for which system of sprinklers in your yard.
On each valve (which the solenoid is on) is a little round knob. Turn the round knob counter clockwise to open that valve. Now go check to see which sprinklers are on. This will tell you which valve goes for which system of sprinklers in your yard.
Do I need to shut off the entire house power to swap out wires on solenoids when I replace anti-siphon valves or just the controller sprinkler system to be in off mode? I want to avoid getting electrocuted.
Thank you, Brad. This helped me a lot.
Gregory, thanks for pointing out to watch out for the old O ring. It was left behind when I replaced the solenoid and the new one would not shut off as a result. Luckily I read thru the comments here and was able to figure out the problem.
Hi how can you tell what wire is the common wire coming from solenoid if both wire are black?
some replacement solenoids have a small white guard around the plunger - should this be removed before installation? I do not see one in the picture on the solenoid.
No, this should remain.
Do you need to turn off the electrical power first?
How do you know which solenoid goes with what zone on your system? We don't have just one control box we have about 4 of the small round control boxes spread about the front & back yard. Some have just one solenoid & others have 2. =/
One of my zones stays on slightly after the scheduled time while my other timed zones are sprinkling. Would this be a problem where that zone solenoid needs to be replaced?
Do rainbird solenoids get replaced the same way, as ours have little handles on them?
What happens if you don't turn off the main water before removing the solenoid?
Does it matter which wire's go where when hooking up the solenoid?
as far as the wires on the solenoid, no, you can use either of the two.
@@orbitsprinklers
Yes I should have clarified that's exactly what I meant thank you for your response
black and white wire does not matter, the sprinkler system is a AC not DC system so there is no polarity.
That is great for the value in the video, but what if you have the type of valve that has the solenoid on the side and the adjustment in the center? Like this one: 3/4"FPT Auto Inline Valve With Flow Control
Can i buy this system
Thank you. This helped a lot. Actually, in my case, I also had a short in the wiring.
have replaced the solenoids and it hasn't fixed the problem, I have 3 valves and the middle one isn't turning itself on with the timer...its making the sounds at the valve box, but not coming on
If my zone won't shut off after trying to fire up the system after the winter, does that mean the solenoid is shot?
+Bob Gaddis it could be multiple things bob, If your system has been winterized its very possible that the bleed screw has been turn on which totally bypasses what the solenoid is meant to do. Make sure its off and if that fails make sure the timer isnt running on its own. Also the solenoid might not be fully shut which means you might have to try and rotate the solenoid clockwise to tighten it. If all these steps are not working then you're looking at a solenoid
problem.
Just want to say thanks! This video helped!
yes,but be sure you dont tighten too tight because you can stretch the o-ring and the valve wont shut off. hope that helps.oh and the little handle comes off,basically the same procedure,the wires can be reversed
Why do my new solenoids / manifold leak slightly through the last dripper ? Why would this
I have a problem. My rainbird controller fuse blows off when it gets to zone 5 out of 7 zones. When i turn the zone 5 to 00 running time, it skips the zone 5 and works fine all the way to zone 7. I am guessing that there is some electric issue with zone 5 valve. Any suggestions?? replace valve or replace solenoid or what???
Hire me and I'll fix it then I'll tell you what it is
I've changed out my solenoid and now it's making a hissing noise if I turn it a bit as if I was treating it Manuelie it stops but it still releases water what is the problem
this could be a number of things. we'd need to speak with you and try some different fixes to determine the problem. Please send your contact info via private message to our social media and we'll get in touch. Thanks.
I can buy the sprinkler valve in Germany?
I have a valve leaking, I guess I need to replace the whole valve, would you agree?
It could just be the diaphragm. No way to say for sure.
What was the name of the tool he uses to cut and strip the wire coating?!
+SpectreRSG It's called a multi-purpose electrician's tool. It cuts and strips wire, trims bolts to length, crimps connectors, and more.
Here is one:
www.altex.com/Klein-Tools-Combination-Wire-Stripper-Cutter-Multi-Purpose-Electricians-Tool-1001-P143496.aspx
Very helpful. Thanks for posting this.
Replace solenoid that zone is keep running...???? Plz help
How to find out that a solenoid Is bad?
It's only 24 volts at very low current to operate the solenoids.
Very helpful,thanks for sharing...
you have infinite resistance on that zone,go to your timer find what color the wire is and referance it back to your valve box,or test your silinoids with a volt meter,turn to ohms and if it goes to zero your silinoid needs to be replaced
Hi Jason, Is there a way to test the solinoids without having to cutting all the wires and then using a voltmeter to find the faulty solinoid. i.e any way of testing to see which one is faulty first.
0:58 use dielectric grease on connections
Nice too easy
Very helpful.
What does a solenoid do???
+John Smith The solenoid allows the valve to turn on when power is sent from the common wire and the zone wire. Without one the valve wouldn't be able to turn on via the timer.
FYI spin up the station first before you fully secure it, incase you f**k up
Thank you :-)
Nice video. Except you probably shouldn't have cut off and dropped the old wire nuts and left them in the ground. Not good for the planet.
Mate that's not solenoid valve it's a coil. Get your shit together.
Coming from the guy who doesn't know the difference between your and you're.
Next to each valve (which the solenoid is on) is a little round knob. Turn the round knob counter clockwise to open that valve. Now go check to see which sprinklers are on. This will tell you which valve goes for which system of sprinklers in your yard.