Thx for this tutorial! A heads up for people who do this for the first time: the original parts are WAY tighter than these 😅 Had to get some proper tools to open them
Awesome video! At first, I was skeptical since it had no voice, but the caption does it all! I don't believe this video was watched over 13,000 times but only 22 people had commented on this video. You saved me $50 for a replacement blender! Much thanks!
Oh thank you. I thought I was gonna have to throw it out. We normally leave stuff on the wall outside , if people can fix them have them. Times are hard I have to fix my stuff now. Thank you so much. X
Thank you so much 👍👏👏✊✊ I had taken my bullet aprat as the switches were glued shut from over flow. I was fallowing a couple of other videos that the plastic part of gear was gone and only the brass bolt was there. So I wasn't having any luck untill your video. WOW put the bottm cover back on it will hold the screwdriver in the motor bolt . Without the bottom cover the screwdriver kept slipping out 😂 Once again appreciate you thank you 😊
Question about one of the blade peace. Does it have a metal washer between the rubber peace and the golden part attached to the blade peace? Mine has a washer and it seems very wore out. Should I replace it too. Thanks!
I'm missing one of the circles at the bottom that holds the base stable. I've looked all over the internet but couldn't find any piece. Any idea on where i can find those?
Had my 1st Magic Bullet for years. Just got a new one.. One 3rd run, the plastic gear shattered. I bought the new parts which arrived today....HOWEVER, I just noticed the new MB doesn;t have the opening at the base to access the screw. Sigh.
The unit with the blade. That gear seems to be mineralized to the shaft. Basically the inside of the screw is minerlized so I can't remove the black runbber gear. Should I ty soaking it in vinegar? KI don't want ot spray WD 40 on it because it's near food. Thanks!
Sorry I did not see your comment sooner I do not come on here very often. Yes you can soak it and vinegar it will help dissolve those minerals and you can wiggle it back and forth to help loosen it up good luck
I have had mine for nearly 15 years now and have changed the gear and rubber parts a few times. Today though I realised: 1. the little rubber feet come out and are hiding screws which makes it much easier (or even possible if the screw has blown out or if yours doesn't have the slot) to remove the cog - use a well folded tea towel to hold the flywheel in the bottom of the unit and pliers or locking pliers on the plastic cog. If it doesn't seems to budge, try going the other way :D and 2. These things are some of the best made appliances of all time. I have been saying I'd buy another one in a heartbeat if mine broke for at least ten years now and it looks like its still got plenty of life left in it now. Magic Bullets rule!!
Sorry unable to do the way shown by you, the plastic part in blender just doesn’t more and also the grove on screw has worn off unable to hold a screw driver any more.. any other method possible ? Please help…. Thanks
First make sure you are turning it the right way. It is the opposite of normal, "turn to the right to remove not the left. If you already did that you will have to take the bottom off. Turn it upside down, pull the little rubber feet out there are screws hidden behind them. remove the bottom and try again. might have to use channel locks to hold it. good luck!
I don't know if anyone else has same issue but with mine it turns on straight away without putting anything on as soon as I plug it in its like the pressure plates are broken on it anyone know how to fix this?
Sounds like you will have to disassemble your Magic Bullet. Do the white bars spring back or are they stuck down? Clue two of them will click when you depress them to switch on the motor the switches might be broke. You will have to completely disassemble and replace the if you can find them might be better off just buying a new one.
Unfortunately the Magic Bullet Mini doesn't have that secret hidden screw on the bottom...I'm going to try to remove the whole base. Screws are under the base foot pads.
I got them on Amazon you can just put Magic Bullet base gear and it should come up..... this link should get you there thanks.... www.amazon.com/Magic-Bullet-Blender-MB1001-Replacement/dp/B07CGKK21J/ref=mp_s_a_1_3?crid=NTU4C1CJKVW6&keywords=magic+bullet+base+gear+replacement&qid=1680134681&sprefix=Magic+Bullet+replacement+gear%2Caps%2C595&sr=8-3
Just what I needed. Mine had a qc sticker over slot on bottom of the Magic Bullet so I had no idea the screwdriver slot was there. My plastic gear cracked so replacement might've been easier since I could lock onto brass nut with channel lock pliers. Great community answering other questions too.
Рік тому
Keep posting videos like this one! This was both extremely helpful and very relaxing to watch. There’s some ASMR folks that would love to watch this.
Kudos on showing this!! Made me nervous that it was still plugged in while you fixed it... thanks
This video was AWESOME.! Very clear and loved the demo. No music. No talking. Perfect!!!! Thank you!!!!!
Just creepy, stalker, phone calling breathing. But yes. Straight to the point, no fluff.
Exactly what I needed no fluff and time wasting. Straight to the point. Time efficient. Thank you, much appreciated.
Thank you! I've had my Magic Bullet for over a decade and the base gear broke. So glad to know all I need is a new gear!
For anyone who tries this….
Safety first. Unplug the machine before changing any parts. 😮
Thx for this tutorial! A heads up for people who do this for the first time: the original parts are WAY tighter than these 😅 Had to get some proper tools to open them
You just saved us $40+ for a new machine, THANK YOU!
Awesome video! At first, I was skeptical since it had no voice, but the caption does it all! I don't believe this video was watched over 13,000 times but only 22 people had commented on this video. You saved me $50 for a replacement blender! Much thanks!
Oh thank you. I thought I was gonna have to throw it out. We normally leave stuff on the wall outside , if people can fix them have them. Times are hard I have to fix my stuff now. Thank you so much. X
Thank you so much 👍👏👏✊✊
I had taken my bullet aprat as the switches were glued shut from over flow.
I was fallowing a couple of other videos that the plastic part of gear was gone and only the brass bolt was there.
So I wasn't having any luck untill your video.
WOW put the bottm cover back on it will hold the screwdriver in the motor bolt . Without the bottom cover the screwdriver kept slipping out 😂
Once again appreciate you thank you 😊
Did you do all that while it was plugged in?
Thanks for tutorial!
Thank you for the simple instructions.
You're a man of few words!! LOL
Personally I would have unplugged the bullet as a precaution before changing the gears.
I have MB 1001 model and need to replace the upper plate wheel that adjust the motor to the housing. Any idea where I can get it online? Thanks.
Question about one of the blade peace. Does it have a metal washer between the rubber peace and the golden part attached to the blade peace? Mine has a washer and it seems very wore out. Should I replace it too. Thanks!
yes I would replace it. it is probably a spacer to make sure you get good contact with the base.
@@diyhomeimprovement9298 thank you so much :)
Thanks a lot, this video just made my day.
Good job. Very helpful l. Thank you.
I'm missing one of the circles at the bottom that holds the base stable. I've looked all over the internet but couldn't find any piece. Any idea on where i can find those?
Thanks for this tutorial 🙏
Please unplug all electrical appliances before changing parts.
how to order transparen gear 6mm dia. inside for magic bullet juicer
I got mine on amazon. It is hard to find parts now so look around.
Sorry I just saw your comment hope its not too late. I ordered them through amazon. Some people are having a hard time findings parts now . good luck!
I buyed on ebay
Had my 1st Magic Bullet for years. Just got a new one.. One 3rd run, the plastic gear shattered. I bought the new parts which arrived today....HOWEVER, I just noticed the new MB doesn;t have the opening at the base to access the screw. Sigh.
Me too! I’m looking at the base of mine and it doesn’t have an opening to do this!!!!😢
Look for my other comment here if you still have it!
Thank you so much dear sir for this video
Very helpful
🙏🏻
You ever sharpen the blades?
Unplug. Good Job. Brief
The unit with the blade. That gear seems to be mineralized to the shaft. Basically the inside of the screw is minerlized so I can't remove the black runbber gear. Should I ty soaking it in vinegar? KI don't want ot spray WD 40 on it because it's near food. Thanks!
Sorry I did not see your comment sooner I do not come on here very often. Yes you can soak it and vinegar it will help dissolve those minerals and you can wiggle it back and forth to help loosen it up good luck
I have had mine for nearly 15 years now and have changed the gear and rubber parts a few times. Today though I realised:
1. the little rubber feet come out and are hiding screws which makes it much easier (or even possible if the screw has blown out or if yours doesn't have the slot) to remove the cog - use a well folded tea towel to hold the flywheel in the bottom of the unit and pliers or locking pliers on the plastic cog. If it doesn't seems to budge, try going the other way :D
and
2. These things are some of the best made appliances of all time. I have been saying I'd buy another one in a heartbeat if mine broke for at least ten years now and it looks like its still got plenty of life left in it now. Magic Bullets rule!!
Senza staccare la presa dalla corrente?
Same issue as mine. Thanks for this!
Thanks for the video
Sorry unable to do the way shown by you, the plastic part in blender just doesn’t more and also the grove on screw has worn off unable to hold a screw driver any more.. any other method possible ? Please help…. Thanks
First make sure you are turning it the right way. It is the opposite of normal, "turn to the right to remove not the left. If you already did that you will have to take the bottom off. Turn it upside down, pull the little rubber feet out there are screws hidden behind them. remove the bottom and try again. might have to use channel locks to hold it. good luck!
@@diyhomeimprovement9298 this is the reply I needed. 👏
Nice! Where did you get the parts?
I got them on Amazon
Good video, but this part broken in half and the gold part stay in the base, how can I out this???? Sorry my english is not good
You will have to use a pair of pliers or channel locks to hold on to that gold peace. Good luck
@@diyhomeimprovement9298 🙄🙄thanks
I don't know if anyone else has same issue but with mine it turns on straight away without putting anything on as soon as I plug it in its like the pressure plates are broken on it anyone know how to fix this?
Sounds like you will have to disassemble your Magic Bullet. Do the white bars spring back or are they stuck down? Clue two of them will click when you depress them to switch on the motor the switches might be broke. You will have to completely disassemble and replace the if you can find them might be better off just buying a new one.
Nice voice
Merveilleux ! ! Merci 😊
Tq 🎉
Thank you so much
wow that was easy
THNKS BRO
Grazie
Awesome!
Kewl. But unplug the device first.
UNPLUG IT FIRST! I hope you don't own a gun, my friend.
Damn. Buddy.. why your breathing so hard and heavy ??? 😮
👍👍👍👍👍👍👍
Disconnect it before!!
Im from India ,no one is repairing this center part from where can i order.Middle gear is jammed😢
Reminder to unplug it from the power outlet before working on anything!
So easy!! Thanks for helping save my magic bullet mini from the landfill.
Unfortunately the Magic Bullet Mini doesn't have that secret hidden screw on the bottom...I'm going to try to remove the whole base. Screws are under the base foot pads.
Where did you get that replacement spare parts and how to buy?? Please tell me
Thank you. This helped me a lot!! Turn to the right. And I was not aware of the screw slot on the bottom.
Do you really leave it plugged in while you’re working on it?😮
Do you have the link for the parts?
😊красава меньше слов брльше дела
thanks
Fake
Fantastic, can now repair mine so easy
Do you have the link for the parts?
I got them on Amazon you can just put Magic Bullet base gear and it should come up.....
this link should get you there thanks....
www.amazon.com/Magic-Bullet-Blender-MB1001-Replacement/dp/B07CGKK21J/ref=mp_s_a_1_3?crid=NTU4C1CJKVW6&keywords=magic+bullet+base+gear+replacement&qid=1680134681&sprefix=Magic+Bullet+replacement+gear%2Caps%2C595&sr=8-3
Just what I needed. Mine had a qc sticker over slot on bottom of the Magic Bullet so I had no idea the screwdriver slot was there. My plastic gear cracked so replacement might've been easier since I could lock onto brass nut with channel lock pliers. Great community answering other questions too.
Keep posting videos like this one! This was both extremely helpful and very relaxing to watch. There’s some ASMR folks that would love to watch this.
Thank you for your help, it’s easy and amazing
Thank you! I almost broke for real my Magic Bullet trying to change that item 😅
Thank you. Straight to the point
Nice thank you
Thanks for this video 🙏
Where did you buy those parts? On Amazon they sell those separately...thank you
yes I got the on Amazon. they came in a three pack. Everything is hard to find these days.
Where can you buy the replacement part?
I found them on Amazon
You Da man!