Here are the links to some of my other videos I talked about in this one DJI O3 FCC Hack - ua-cam.com/video/efVPu2JKZPY/v-deo.html DJI O3 Vibrations Issues - ua-cam.com/video/p3WdkTMxlVU/v-deo.html DJI O3 Complete FCC vs CE RF Guide - ua-cam.com/video/21C80SiUWZA/v-deo.html DJI O3 Harness Warning - ua-cam.com/video/dwR4BIhfxtw/v-deo.html DJI O3 How Hot Will It Get - ua-cam.com/video/e7cKL7M5aSM/v-deo.html DJI O3 Teardown - ua-cam.com/video/z4tQZmevEtw/v-deo.html DJI O3 DJI FPV Remove V2 Setup - ua-cam.com/video/teR4S9WxvEU/v-deo.html DJI O3 Power Requirements - ua-cam.com/video/ClavnlN663Y/v-deo.html I hope you have found this video helpful .
Sussed it out. it was the connection cable. It was not putting enough power through to be able to bind. Would light up the turn off. Tried with another cable works perfect. Thanks for the help man and this video. Hope your well cheers J
Thank you for the great guide. I'm still looking for a guide on how connecting the O3 to a TBS Crossfire transmitter. I have the TBS module for the Taranis X9D.
Mr Steele mustache man should watch this. He was complaining of the feed whilst in low power mode. Even in this video you can see it was choppy and then you armed and was buttery smooth.
I saw the same thing. You can clearly see 7mb/s in 1 set of goggles and 50mb/s other. I don’t know how you miss that trying to make a comparison unless you know 0 about how these transmissions systems work. And I don’t know how you get that far without knowing anything about how they work either.
Thank you so much for this video. You’re the only one I could find that explains everything clearly and I appreciate the troubleshoot segment. No one warns us new user about tue possibilities of the wiring being wrong, which was the case for me. DJI harness had tx/rx switched. Explains why I could not get OSD to work.
Great review. I just returned mine as I fly INAV 7.1 and found the OSD to be almost useless. I simply could not get a descent layout as the presentation in the goggles did not match even remotely the layout in the INAV OSD setup screen. I have several Caddx and Runcam units which work perfectly with WTFOSD. So my plane is to eventually go with Walksnail Avatar instead of going down another of DJI's rabbit holes.
Thanks so much for your work. You made my day. I had partly DJI OSD, permanent low power mode and no recording. Thanks to your simulation I could replace the falty grey wire and will get airborne now. THANKS!
Running this in a baja 5b truggy. Using a spektrum dx9 and a 636b receiver with the steering on the rudder and the camera on the elevator and aileron channels so that I can look around while driving. This video made it pretty much painless to connect. Unless I was told to I would have taken forever to figure out the settings change in the goggles. Thank you. Liked and subbed
Just want to say thanks! Finally upgraded to digital, which is excellent - that said, I broke off the small (IPEX?) connecter as I was removing a part of the frame… you mentioned it could be replaced with standard antennas - just curious where they could be purchased - or what length and type are considered standard. Thanks again!!
Your videos are borderline too informational, but I do learn a great deal from you, so thanks! This is related somewhat, but I have the Avata 2 which was my first drone (I am now addicted to FPV) ever. I now own an RTF TanQ 2 5” from Rotor Riot, with the DJI O3 and DJI receiver and the F7 HD+F55A ProII 3-6S 30/30 with F7 FC and 32 bit 55A ESC and I have it flying well and I love it, but I wanted to find limitations for the compatibility with the Remote 3 and Goggles 3 with custom Quads. In 1 video when you reviewed the DJI O3 system you mentioned that you were better off with a different remote as the DJI FPV 3 actually is sending to the goggles 3, then to the air unit for control. I have read if you have a DJI O3 HD and DJI receiver you are married to their FPV remote, but I believe I heard you say otherwise. If i have choices for a remote with the Goggles3/Tanq 2, what would be compatible? Thanks!
Im in USA and just found out my O3 is stuck in CE mode after watching ur video. I activated using same account i do all my dji fpv stuff. I have goggles V2
thank you so much for this information. i have a problem when flying my quad, DJI O3 air unit stop recording while lost signal connection with Goggles 2, but the goggles not stop recording until i disarm/finish flying. why this happen? thank u so much....
Thank you for this video! The flight controller and dji o3 have different connection terminals. In the video, you have a cable that fits perfectly to the flight controller. Where can I get the cable from the flight controller to dji o3?
Very helpful video. Thank you for your efforts to make this subject more understandable. I followed all the instructions, but even though my Goggles 2 are binded to the O3 Unit, when I arm still it does not start recording automatically, I still need to go to the menu of the Goggles and select record from there.
@@TheHelicapt I figured out. In my case I was plugging the USB C cable to the O3 Unit and was thinking that I can make it work that way. But only with the cable not enough power goes to the unit. You need to attach a battery to your quad. You can only bind with while on USB C cable, but you won't see it on the Goggles. Use a battery on your quad and it should be working. Don't forget to remove the props on your quad before that. Hope it helps
Very much appreciated big dawg. Whole othe point though you should spread the word however you can. Basically flite test is trying to raise the 250g to 1kg. They posted last night on their CBO channel I think. And I'm just trying to make sure you big view guys are also aware ASAP.
This absolutely the best guide to date on this new unit. I do wonder if DJI will enventually license/allow RunCam to produce their own branded units given that Caddx has gone the way of the TREX.
hey there i found your channel recently so much good info as im very new to the hobby. ive finally got everything pretty well dialed. is there a way to get a DJI o3 air unit to goggles signal strength represented in the OSD i just got a bit of trouble watching the goggles signal strength as the native OSD icon is small. thanks!
Hi, thanks for your great videos. in Italy I didn't find any results for my problem with the unit03. mounted on a geprc20, during a flight it was disconnected and from that moment when it is powered a green LED remains flashing, and in addition to not seeing anything on the integra it doesn't even connect to the PC. do you know what it could be?
Mine won’t arm either. Goggles show “BADRX”. Looking for answers too. Good luck. I’ll try to remember to come back here and update if I find anything useful.
Nice work mate! Could you do a video going through camera settings etc and best you have found and the differences. Cine vs just everyday FPV flying. Thanks and keep up the great work!
Hi there hope you can help I've powered my 03air with a 2s lipo the wires are solder to the fan wires and the plug plugs into the lipo it all works but won't record to the micro sd in the border it trys but then says low power mode activated won't record and It drops signal for about 5 _8 seconds then comes back on any ideas many thanks
I have V2 goggles, i bound of one of my quad and changed to second quad and bound. When i use my 1st quad again, do i need to rebind? Thank you for answer
Great Vid Ian, still not had time to look at my binding issue. To busy packing boxes. Hopefully I’m just not pushing to right button 😂. Will let you know man. Thanks Ian always super helpful mate. Thanks Justin
You mentioned that if air unit LED will not become solid red after plugging in battery it's most likely the unit is not fully powered. Looks like I'm experiencing that issue in my diy nazgul evoque v2 build. Brand new o3 properly wired but powering up battery make air unit led solid green - pairing button doesn't have any effect of course. My FC is Iflight Blitz mini f7 - and honestly can get my head around with this - you suggested some power switch, but can't find anything in BF.
This Information is so useful!!! Thanks! I would love it if you found away to get the air unit to perform at max without the use of a flight controller as I am using it in an RC plane.
Did u get it working? Trying to make a wing myself with 03 unit and my v2 goggkes and rc2 remote but not clear if the remote will work, I know it does for a drone but not a wing
Great video, thank you. Just out of curiosity, do we know if having all of this power, does it have any adverse health issues on our body, especially the brain?
great video and very helpful!! i just got the o3 air unit for my rc planes. im in market for goggles now but i was wondering if i need a flight controller for o3 or if it would connect to Spektrum Air Receiver??
I purchased a flywoo with a 03 unit. And it shows up in the app but will not pop up the activation window. Any suggestions? Is there a way to look at my account and see what’s activated on my account?
Thanks Ian . Love your videos mate. But I have a question on switching to my vista units with my DJI v2 goggles. Every time I switch from 03 to Vista it keeps telling me to power cycle my goggles then i have to rebind every time . This is so annoying. Is there a solution to this? Thanks Ian
Sadly no. This is how DJI designed it. There are some technical limitations to how they implemented the different modes in the goggles and it results in the need to rebind when you switch modes.
I currently have the vista set up on my FC, but I am getting the O3 on monday. Assuming all the wiring is correct, and assuming I don't personally have a need to add anything from betaflight's OSD at the moment, shouldn't the DJI OSD theoretically come up on my goggles as soon as they are bound together, without any presets in betaflight?
Thanks for the great video. I have 1 question: If I delete the existing Ham-File from the Sd-Card and I restart the goggles V2, the powermode goes back/ less RF-Power? Ham-File must be always on the Sd-Card? Thanks a lot
No once it’s done it will stay till either you connect to assistant 2 or you reset the goggles to factory settings. You do not need to leave it on the card in normal use.
Hi boss, many thanks for your fantastic guide and tutorials, I have an absurd problem with my two new dji O3s: I have two Kakute H7 fc mounted on two of my 5" freestyles, the first is a H7 V2: when I connected it to the O3 the fc is dead, it is no longer powered by usb or from lipo, with the second fc which is a Kakute H7 V1.2, if it's connected the plug to the O3 air unit, the quad does not arm, I see in my dji V2 the image from the cam but the quad does not arm: I checked the connections between the fc and the O3 air unit several times and they are correct in both cases: what can I do to solve it? what could be the problem? many thanks
Quick question. Running the Mobula8 with DJI 03. Throttle, Pitch Yaw and Roll all respond in Betaflight. But when I arm the drone to fly only Pitch, Yaw and Roll work. Using the DJI remote 2. Do I need to adjust the thresholds in the receiver tab or something?
You mentioned connecting the 03 camera wire connectors to a flight controller OR a power supply. I'm trying to use my 03 camera on a fixed wing aircraft that does not have a flight controller, only an ESC. Can the power leads just be connected to a battery using the power leads on the camera? I'm told that the camera goes into a low power mode. (.25) How does the low power mode still supply enough power to operate the camera at normal 'line of site' ranges? Can I use those power supply of a balance plug of the proper voltage? Your help would be greatly appreciated. Thank you.
You can absolutely use O3 just on the battery with in its accepted voltage range with out an FC however it’s worth noting while you can turn off low power mode it’s still not full RF power and as such you may get reduced range. O3 Must have an Arming command from a flight controller to get full RF power.
Great vid as always. I have an 03 air unit, v2 goggles and controller 2. I can’t get rid of the country code error. I have refreshed the updates but still get the message. Also, I can’t access the advanced functions in the controller as they aren’t highlighted. And I can’t change from 16:9 to 4:3. Some strange stuff going on.
1yr later I don't even fly my 03, mine just never got any more range than my Vista. Having a camera that can't be mounted in any of my frames and software that requires me to rebind my gogglesv2 every time I want to use it, total pita. I guess I find the waterproof Vista more rugged than 03, and the hero7 to have a better image. 03 was pretty useless for me, guessing 04 will be the same.
the mamba mk4 f740 aio power the o3 air unit directly with vbat.... is there any over heating or risk by doing that......the aio also have a tvs diod protection for safety ..... or i need to cut the wire and add a bec for safety...... please help.. i am a little bit confused
FOCUS ISSUE!! Is there a way to focus the 03 Air Unit? Our is only focused at extreme close and I do not know how to get it to get the focus back to far for flying. Thanks!
@Mads Tech do you know of a preset for betaflight 4.3 if I'm using the 03 air unit with the DJI controller? Supafly is only 4.4 I believe, at least I don't see one for DJI remote only one with the options for crossfire and ELRS etc.
Hi Ian, thank you very much for your work and efforts to make this subject more understandable for beginners FPV pilots like me. I have question. I recently bought DJI Avata with Goggles Integra and FPV controller 2. I had some issues loosing connection and with the help of your videos I was able to switch to FCC mode using the ham file hack. I also bought the GEPRC CineLog 35 V2 PNP version and trying to use the same Goggles Integra and FPV Controller 2 to fly the the CineLog 35 V2 with the same set up. The question is if I update firmware on the Goggles Integra do I need to perform the ham hack again in order not to loose the FCC mode when I use to the Avata? Thank you again for your time and efforts.
Hi can you please help on setup dji air unit o3? I recorded video 6 times both in my goggles and air unit internal storage. I found exact 6 videos in my goggles but in o3 only found 3 videos.
My air Unit is blinking red and green at the Same Time when im powering it up. I dont Know What to do, everthing is connectet up correctly and it has enough power. Dont Know What to do know
Hi is it possible to attach this to a RC car without a FC and just power it from the battery balance lead? And will it bind with the DJI google2 automatically?
I'm having issues binding my O3 - but it's worked before and I haven't changed anything or crashed. The V2s start beeping (binding mode) and the O3 red LED starts blinking (binding mode) but it never connects. Any tips?
I got the 03 mode in my Goggles V2 , but I have no way to adjust the power in mw , range seems fine🤔. Also when switching to air mode on my new iflight there's no air mode weird , but flys great lol
While it’s true you can’t bind without the air unit receiving battery power, some things are powered just from USB. Mounting internal storage and SD card storage works with just USB and software updates also work with just USB. This generates much less heat because none of the wireless functionality of the air unit is being powered. This is the same on the Avata. When doing an update or using the air unit as a SD card reader, it’s better to not have a battery plugged in due to the reduced heat generation and it also eliminates the need to remove props for increased safety while performing these tasks.
Why is my dji 03 air unit in ce mode in the first place? I live in the us and I activated it in the us so why are all of my dji air units in ce mode I don't understand.
Hey Ian, I just bought the goggles 2 and updated it to the latest firmware and I also did that with the Caddx vista I’m using. When the quad is not armed I got 6mbs and when I arm it goes to 47mbs but when I arm and before I see the 47mbs I got a 0.5sec black screen like a black screen. What is this? Thanks already!
Hi, not found any info of flying my 03 while others are flying vista and the old air unit, no option to drop to 25mw, and are the channels different? Flying today with 03 while someone flying vista, I was on channel 3 he was on channel 1 seemed ok for a while then his picture blacked out.
Very nice video. I know that this is a guide for betaflight , but I wonder if you have any idea for inav. For now , inav has not OSD support . But when I arm the quad , it exits from low power mode and starts recording. The problem is that I have 0 Volts in my V2 goggles for the battery of the quad and the signal is weaker from the previous air unit. Is it possible that this msp behavior , affects the strength of the signal , or from the moment it exits low power mode is irrelevant ? Thanks in advance
I''ve been trying to get my 03 unit to give me osd with the F7 mini stack from T motor and can't seem to get it to work. I've swapped white and gray cables thinking I'm just cross eyed and double and tipple checked Uart's I have no idea what I'm doing wrong. it won't display.
when low power state is gone after armed, that gonna shutdown automatically?, because i already get failsafe 2 times because of automatically disconnect, its like overheat on dji o3 unit, but just flight 1 half minute
Hi to every one. Have problem...looks same as i don't have gray wire. No voltage and signal from FC, but i have OSD on my Googles V2. I had try: change uart. change cable, all steps as from video but nothing. May be some of you have same problem. One time (wihle i'm playing with all this thing) i wired tx nad rx oposit...it could be the problem?
HI. Are the settings for sharpness and noise reduction only available for the newer dji goggles two, as the settings are not there on my dji v2 goggles? thanks.
struggling to find the solution , i have betaflight osd but no dji osd voltge 0.0 with low power, but betaflight osd show all correct . i also try that on different fc with different cable same problem /;
Why is my 03 au only recording bitrate and delay and nothing else also I have the iflight chimera 7 pro V2 worth the 03 au should I direct solder the au directly to battery power
Ok just want to say, further to my issues with me having created a ham file on my Win 10 notepad, that was the issue, even though created perfectly, it didn't want to know.. So I went to one of your other videos, found the zip file, unzipped and pasted onto the SD root... Bingo!! Now working properly and fully unlocked 😁 Just some help if anyone has the same problem. Download the zip file. It just works! The goggles just don't like the Win 10 notepad for some reason.. Lol
Here are the links to some of my other videos I talked about in this one
DJI O3 FCC Hack - ua-cam.com/video/efVPu2JKZPY/v-deo.html
DJI O3 Vibrations Issues - ua-cam.com/video/p3WdkTMxlVU/v-deo.html
DJI O3 Complete FCC vs CE RF Guide - ua-cam.com/video/21C80SiUWZA/v-deo.html
DJI O3 Harness Warning - ua-cam.com/video/dwR4BIhfxtw/v-deo.html
DJI O3 How Hot Will It Get - ua-cam.com/video/e7cKL7M5aSM/v-deo.html
DJI O3 Teardown - ua-cam.com/video/z4tQZmevEtw/v-deo.html
DJI O3 DJI FPV Remove V2 Setup - ua-cam.com/video/teR4S9WxvEU/v-deo.html
DJI O3 Power Requirements - ua-cam.com/video/ClavnlN663Y/v-deo.html
I hope you have found this video helpful .
Sussed it out. it was the connection cable. It was not putting enough power through to be able to bind. Would light up the turn off. Tried with another cable works perfect. Thanks for the help man and this video. Hope your well cheers J
Thank you for the great guide. I'm still looking for a guide on how connecting the O3 to a TBS Crossfire transmitter. I have the TBS module for the Taranis X9D.
@@PhilippZ you won’t be able to connect it directly. You will need to get a nano or similar and connect that to the transmitter.
I spent days trying to find the solution to my osd problem. After watching your video my issue has been fixed. Thank you!
Mr Steele mustache man should watch this. He was complaining of the feed whilst in low power mode. Even in this video you can see it was choppy and then you armed and was buttery smooth.
Steele needs to watch alot of things, lol. Stuck in 2018.
I saw the same thing. You can clearly see 7mb/s in 1 set of goggles and 50mb/s other. I don’t know how you miss that trying to make a comparison unless you know 0 about how these transmissions systems work. And I don’t know how you get that far without knowing anything about how they work either.
@@s.flying1022 easy, you always fly anolog
He said that even when flying it’s choppier than the v2.
Thank you so much for this video. You’re the only one I could find that explains everything clearly and I appreciate the troubleshoot segment. No one warns us new user about tue possibilities of the wiring being wrong, which was the case for me. DJI harness had tx/rx switched. Explains why I could not get OSD to work.
Great review. I just returned mine as I fly INAV 7.1 and found the OSD to be almost useless. I simply could not get a descent layout as the presentation in the goggles did not match even remotely the layout in the INAV OSD setup screen. I have several Caddx and Runcam units which work perfectly with WTFOSD.
So my plane is to eventually go with Walksnail Avatar instead of going down another of DJI's rabbit holes.
Thanks so much for your work. You made my day. I had partly DJI OSD, permanent low power mode and no recording. Thanks to your simulation I could replace the falty grey wire and will get airborne now. THANKS!
Running this in a baja 5b truggy. Using a spektrum dx9 and a 636b receiver with the steering on the rudder and the camera on the elevator and aileron channels so that I can look around while driving. This video made it pretty much painless to connect. Unless I was told to I would have taken forever to figure out the settings change in the goggles. Thank you. Liked and subbed
I set mine up with the HD osd just the other day and it appears to be working correctly for me.
Thanks @Mads Tech , couldn't get my OSD working,your video fixed it 😊
Just want to say thanks! Finally upgraded to digital, which is excellent - that said, I broke off the small (IPEX?) connecter as I was removing a part of the frame… you mentioned it could be replaced with standard antennas - just curious where they could be purchased - or what length and type are considered standard. Thanks again!!
Your videos are borderline too informational, but I do learn a great deal from you, so thanks! This is related somewhat, but I have the Avata 2 which was my first drone (I am now addicted to FPV) ever. I now own an RTF TanQ 2 5” from Rotor Riot, with the DJI O3 and DJI receiver and the F7 HD+F55A ProII 3-6S 30/30 with F7 FC and 32 bit 55A ESC and I have it flying well and I love it, but I wanted to find limitations for the compatibility with the Remote 3 and Goggles 3 with custom Quads. In 1 video when you reviewed the DJI O3 system you mentioned that you were better off with a different remote as the DJI FPV 3 actually is sending to the goggles 3, then to the air unit for control. I have read if you have a DJI O3 HD and DJI receiver you are married to their FPV remote, but I believe I heard you say otherwise. If i have choices for a remote with the Goggles3/Tanq 2, what would be compatible? Thanks!
You can use whar every remote system you want on O3, Dji can not force you to use theirs inav and betaflight can take any remote.
Thank you for explaining. Very well done!
Lovely work Mads,
Thanks for All
The help 😊
Im in USA and just found out my O3 is stuck in CE mode after watching ur video. I activated using same account i do all my dji fpv stuff. I have goggles V2
thank you so much for this information. i have a problem when flying my quad, DJI O3 air unit stop recording while lost signal connection with Goggles 2, but the goggles not stop recording until i disarm/finish flying. why this happen? thank u so much....
Thank you for this video! The flight controller and dji o3 have different connection terminals. In the video, you have a cable that fits perfectly to the flight controller. Where can I get the cable from the flight controller to dji o3?
Thank you very much from Brazil
Very helpful video. Thank you for your efforts to make this subject more understandable. I followed all the instructions, but even though my Goggles 2 are binded to the O3 Unit, when I arm still it does not start recording automatically, I still need to go to the menu of the Goggles and select record from there.
I have the same problem. whats the solution ?
@@TheHelicapt I figured out. In my case I was plugging the USB C cable to the O3 Unit and was thinking that I can make it work that way. But only with the cable not enough power goes to the unit. You need to attach a battery to your quad. You can only bind with while on USB C cable, but you won't see it on the Goggles. Use a battery on your quad and it should be working. Don't forget to remove the props on your quad before that. Hope it helps
@@sethvane669 thanks
Very much appreciated big dawg. Whole othe point though you should spread the word however you can. Basically flite test is trying to raise the 250g to 1kg. They posted last night on their CBO channel I think. And I'm just trying to make sure you big view guys are also aware ASAP.
This absolutely the best guide to date on this new unit. I do wonder if DJI will enventually license/allow RunCam to produce their own branded units given that Caddx has gone the way of the TREX.
Thanks so much. the OSD info really helped!!
"I am using DJI 03 and Googles V2, is there any way to record OSD information on the video?"
hey there i found your channel recently so much good info as im very new to the hobby. ive finally got everything pretty well dialed. is there a way to get a DJI o3 air unit to goggles signal strength represented in the OSD i just got a bit of trouble watching the goggles signal strength as the native OSD icon is small. thanks!
Very helpful 👍🏻 Thanks & subscribed 🤚🏻
Hi, thanks for your great videos. in Italy I didn't find any results for my problem with the unit03. mounted on a geprc20, during a flight it was disconnected and from that moment when it is powered a green LED remains flashing, and in addition to not seeing anything on the integra it doesn't even connect to the PC. do you know what it could be?
What's the best FC for the o3 on a EDF plane guys? Thanks
if i just want to use the 03 air unit to bind to my goggles 3 and install in roban 800 heli do i still need a flight controller ?
Hi - great video - do you know if this can be fitted to a DJI Avata ? thanks
my air unit wont arm and is showing MSP instead of arming any help please just built and spent hours trying to figure it out. thank you
Mine won’t arm either. Goggles show “BADRX”. Looking for answers too. Good luck. I’ll try to remember to come back here and update if I find anything useful.
Mads, I need you to brave the horrible weather and test that 90 FPS CAM OK I'M DYING TO HEAR IT 😘
Nice work mate! Could you do a video going through camera settings etc and best you have found and the differences. Cine vs just everyday FPV flying. Thanks and keep up the great work!
Do you mount the O3 with double sided tape? Why are there no mounting screws
can I just connect positive and negative from a Bec to run the O3 with my integrate goggles if I'm putting the O3 is an RC plane?
Another awesome video!! Thank you!
How do you connect it directly to a battery, if want to use it on an Rc truck?
Hi there hope you can help I've powered my 03air with a 2s lipo the wires are solder to the fan wires and the plug plugs into the lipo it all works but won't record to the micro sd in the border it trys but then says low power mode activated won't record and It drops signal for about 5 _8 seconds then comes back on any ideas many thanks
I have V2 goggles, i bound of one of my quad and changed to second quad and bound. When i use my 1st quad again, do i need to rebind? Thank you for answer
YESS!!! Thank you for this Ian!!!
Great Vid Ian, still not had time to look at my binding issue. To busy packing boxes. Hopefully I’m just not pushing to right button 😂. Will let you know man. Thanks Ian always super helpful mate. Thanks Justin
This just saved me a huge headach
The final guide we were all looking for, simply thanks !!
You mentioned that if air unit LED will not become solid red after plugging in battery it's most likely the unit is not fully powered. Looks like I'm experiencing that issue in my diy nazgul evoque v2 build. Brand new o3 properly wired but powering up battery make air unit led solid green - pairing button doesn't have any effect of course. My FC is Iflight Blitz mini f7 - and honestly can get my head around with this - you suggested some power switch, but can't find anything in BF.
Did you find solution for this issue? I’m experiencing exactly the same with my brand new mark5 for the last few weeks
On the latest Betaflight...does the VX(MSP) still need to be selected to work OCD etc for DJI 03 ?
and how do I know what UART is my board using?
This Information is so useful!!! Thanks! I would love it if you found away to get the air unit to perform at max without the use of a flight controller as I am using it in an RC plane.
Sadly no, I have asked DJI for an update to resolve this but they never replied.
were you able to use crash flip mode?
Do you think there is a way to use dji fpv controller 2 with crossfire reciever? This would be awsome to prevent looseing signal
Great video. Subbed. I have bound my remote 2 and goggles no problem but there is no response on the receiver tab on betaflight? any ideas?
Did u get it working? Trying to make a wing myself with 03 unit and my v2 goggkes and rc2 remote but not clear if the remote will work, I know it does for a drone but not a wing
Great video, thank you.
Just out of curiosity, do we know if having all of this power, does it have any adverse health issues on our body, especially the brain?
great video and very helpful!! i just got the o3 air unit for my rc planes. im in market for goggles now but i was wondering if i need a flight controller for o3 or if it would connect to Spektrum Air Receiver??
I purchased a flywoo with a 03 unit. And it shows up in the app but will not pop up the activation window. Any suggestions? Is there a way to look at my account and see what’s activated on my account?
Why It doesnt start recording when I arm??? I also want to see the time when I arm to count down. I liked that on my V2 goggles .
Thanks Ian . Love your videos mate. But I have a question on switching to my vista units with my DJI v2 goggles. Every time I switch from 03 to Vista it keeps telling me to power cycle my goggles then i have to rebind every time . This is so annoying. Is there a solution to this? Thanks Ian
Sadly no. This is how DJI designed it. There are some technical limitations to how they implemented the different modes in the goggles and it results in the need to rebind when you switch modes.
@@MadRC ok thanks Ian
@@MadRC Ian we have get you on our show one day . Whenever your available my friend just let me know if your interested. We’ll set a date
Hey Mads, i just wondering if that unit can be record without flight controller? 'cause i think maybe could be use as bikers tiny vlog camera
I currently have the vista set up on my FC, but I am getting the O3 on monday. Assuming all the wiring is correct, and assuming I don't personally have a need to add anything from betaflight's OSD at the moment, shouldn't the DJI OSD theoretically come up on my goggles as soon as they are bound together, without any presets in betaflight?
Thanks for the great video. I have 1 question: If I delete the existing Ham-File from the Sd-Card and I restart the goggles V2, the powermode goes back/ less RF-Power? Ham-File must be always on the Sd-Card? Thanks a lot
No once it’s done it will stay till either you connect to assistant 2 or you reset the goggles to factory settings. You do not need to leave it on the card in normal use.
Great Info, thanks Ian
Hi boss, many thanks for your fantastic guide and tutorials, I have an absurd problem with my two new dji O3s: I have two Kakute H7 fc mounted on two of my 5" freestyles, the first is a H7 V2: when I connected it to the O3 the fc is dead, it is no longer powered by usb or from lipo, with the second fc which is a Kakute H7 V1.2, if it's connected the plug to the O3 air unit, the quad does not arm, I see in my dji V2 the image from the cam but the quad does not arm: I checked the connections between the fc and the O3 air unit several times and they are correct in both cases: what can I do to solve it? what could be the problem? many thanks
Quick question.
Running the Mobula8 with DJI 03.
Throttle, Pitch Yaw and Roll all respond in Betaflight.
But when I arm the drone to fly only Pitch, Yaw and Roll work.
Using the DJI remote 2.
Do I need to adjust the thresholds in the receiver tab or something?
How were you able to connect o3 unit to the Betaflight configurator? Can't make it. Even though it is set to com7 port in system.
You mentioned connecting the 03 camera wire connectors to a flight controller OR a power supply. I'm trying to use my 03 camera on a fixed wing aircraft that does not have a flight controller, only an ESC. Can the power leads just be connected to a battery using the power leads on the camera? I'm told that the camera goes into a low power mode. (.25) How does the low power mode still supply enough power to operate the camera at normal 'line of site' ranges? Can I use those power supply of a balance plug of the proper voltage? Your help would be greatly appreciated. Thank you.
You can absolutely use O3 just on the battery with in its accepted voltage range with out an FC however it’s worth noting while you can turn off low power mode it’s still not full RF power and as such you may get reduced range. O3 Must have an Arming command from a flight controller to get full RF power.
Great vid as always. I have an 03 air unit, v2 goggles and controller 2. I can’t get rid of the country code error. I have refreshed the updates but still get the message. Also, I can’t access the advanced functions in the controller as they aren’t highlighted. And I can’t change from 16:9 to 4:3. Some strange stuff going on.
I can't either. Tried the DJ fly app to get gps even. Can't find a solution yet. Did you ever figure it out?
1yr later I don't even fly my 03, mine just never got any more range than my Vista. Having a camera that can't be mounted in any of my frames and software that requires me to rebind my gogglesv2 every time I want to use it, total pita. I guess I find the waterproof Vista more rugged than 03, and the hero7 to have a better image. 03 was pretty useless for me, guessing 04 will be the same.
the mamba mk4 f740 aio power the o3 air unit directly with vbat.... is there any over heating or risk by doing that......the aio also have a tvs diod protection for safety ..... or i need to cut the wire and add a bec for safety...... please help.. i am a little bit confused
DJI O3 has a built-in receiver, is it correct? Noone talks about it for noobs
FOCUS ISSUE!! Is there a way to focus the 03 Air Unit? Our is only focused at extreme close and I do not know how to get it to get the focus back to far for flying. Thanks!
options of video format is not available on my BF
it's too bad us surface guys are in the dark. how the hell do i get this thing at full power. Is the arduino working? no idea. stuck at 300m range.
You can use Arduino with code that forces arming. Just search Google for DJI O3 Arduino
will you open the o3 antenna plastic cover. love to know how to check inside.
@Mads Tech do you know of a preset for betaflight 4.3 if I'm using the 03 air unit with the DJI controller? Supafly is only 4.4 I believe, at least I don't see one for DJI remote only one with the options for crossfire and ELRS etc.
Hi Ian, thank you very much for your work and efforts to make this subject more understandable for beginners FPV pilots like me. I have question. I recently bought DJI Avata with Goggles Integra and FPV controller 2. I had some issues loosing connection and with the help of your videos I was able to switch to FCC mode using the ham file hack. I also bought the GEPRC CineLog 35 V2 PNP version and trying to use the same Goggles Integra and FPV Controller 2 to fly the the CineLog 35 V2 with the same set up. The question is if I update firmware on the Goggles Integra do I need to perform the ham hack again in order not to loose the FCC mode when I use to the Avata? Thank you again for your time and efforts.
Yea you will need to do it again but only on the goggles. Just place the ham file back on the sd card and boot up after the update.
@@MadRC thank you so much for the fast reply and all your work to make this understandable for newbies like me 😊😊😊
Hi can you please help on setup dji air unit o3? I recorded video 6 times both in my goggles and air unit internal storage. I found exact 6 videos in my goggles but in o3 only found 3 videos.
This was perfect! 🙌
im lost if i have a rushfpv analogue blade 722 fc. with 5v 5a bec can i solder it using that or can i use the vcc .using a 6s
My air Unit is blinking red and green at the Same Time when im powering it up.
I dont Know What to do, everthing is connectet up correctly and it has enough power.
Dont Know What to do know
Hi is it possible to attach this to a RC car without a FC and just power it from the battery balance lead? And will it bind with the DJI google2 automatically?
I'm having issues binding my O3 - but it's worked before and I haven't changed anything or crashed. The V2s start beeping (binding mode) and the O3 red LED starts blinking (binding mode) but it never connects. Any tips?
i cant see to find the preset anymore in bettaflight preset menus
I got the 03 mode in my Goggles V2 , but I have no way to adjust the power in mw , range seems fine🤔. Also when switching to air mode on my new iflight there's no air mode weird , but flys great lol
While it’s true you can’t bind without the air unit receiving battery power, some things are powered just from USB. Mounting internal storage and SD card storage works with just USB and software updates also work with just USB. This generates much less heat because none of the wireless functionality of the air unit is being powered. This is the same on the Avata. When doing an update or using the air unit as a SD card reader, it’s better to not have a battery plugged in due to the reduced heat generation and it also eliminates the need to remove props for increased safety while performing these tasks.
sup man. ive gotta problem with googles v2 drv. its not showing gps coords in it, but googles shows this info
Why is my dji 03 air unit in ce mode in the first place? I live in the us and I activated it in the us so why are all of my dji air units in ce mode I don't understand.
Is there a chance of getting a tumor due to the extra power?
Hey Ian, I just bought the goggles 2 and updated it to the latest firmware and I also did that with the Caddx vista I’m using. When the quad is not armed I got 6mbs and when I arm it goes to 47mbs but when I arm and before I see the 47mbs I got a 0.5sec black screen like a black screen. What is this?
Thanks already!
Hi, not found any info of flying my 03 while others are flying vista and the old air unit, no option to drop to 25mw, and are the channels different? Flying today with 03 while someone flying vista, I was on channel 3 he was on channel 1 seemed ok for a while then his picture blacked out.
Very nice video. I know that this is a guide for betaflight , but I wonder if you have any idea for inav.
For now , inav has not OSD support . But when I arm the quad , it exits from low power mode and starts recording.
The problem is that I have 0 Volts in my V2 goggles for the battery of the quad and the signal is weaker from the previous air unit.
Is it possible that this msp behavior , affects the strength of the signal , or from the moment it exits low power mode is irrelevant ? Thanks in advance
hi , is there a chance that dji O3 could get the osd on the dvr with the google V2 ?
Anything I can do to get osd for the 03 au with goggles 2 on Betaflight 4.3?
I''ve been trying to get my 03 unit to give me osd with the F7 mini stack from T motor and can't seem to get it to work. I've swapped white and gray cables thinking I'm just cross eyed and double and tipple checked Uart's I have no idea what I'm doing wrong. it won't display.
OMG I redid the presets after swapping white and gray cables now it works!!!!!!!
Mhh, input Voltage, on DJI Homepage 7.4-17.6v?!
when low power state is gone after armed, that gonna shutdown automatically?, because i already get failsafe 2 times because of automatically disconnect, its like overheat on dji o3 unit, but just flight 1 half minute
Hi to every one. Have problem...looks same as i don't have gray wire. No voltage and signal from FC, but i have OSD on my Googles V2. I had try: change uart. change cable, all steps as from video but nothing. May be some of you have same problem. One time (wihle i'm playing with all this thing) i wired tx nad rx oposit...it could be the problem?
Problem was solved by wiring to other uart....so 2 was not good, and 3rd attempt was lucky
HI. Are the settings for sharpness and noise reduction only available for the newer dji goggles two, as the settings are not there on my dji v2 goggles? thanks.
struggling to find the solution , i have betaflight osd but no dji osd voltge 0.0 with low power, but betaflight osd show all correct . i also try that on different fc with different cable same problem /;
Just want to say thanks😊
How do you get rid of country of origin not updated after activation of the 03
You need to connect it to the DJI fly app and then take it all out doors.
Hey do you know how/if OSD can be viewed in the DVR?
Why is my 03 au only recording bitrate and delay and nothing else also I have the iflight chimera 7 pro V2 worth the 03 au should I direct solder the au directly to battery power
great work. thank you.
Ok just want to say, further to my issues with me having created a ham file on my Win 10 notepad, that was the issue, even though created perfectly, it didn't want to know..
So I went to one of your other videos, found the zip file, unzipped and pasted onto the SD root... Bingo!!
Now working properly and fully unlocked 😁
Just some help if anyone has the same problem.
Download the zip file. It just works!
The goggles just don't like the Win 10 notepad for some reason.. Lol